Department Of Employment And Training - Tamil Nadu

33704226 supply, erection and commissioning of machineries and equipment for various government industrial training institute ( iti ) in tamil nadu 1. split type air conditioner 1.5 ton 17 nos ac 2. bottle cooler visible 1 no 3. car ac tutorial model 2 sets 4. de scaling pump set 1 no 5. deep freezer 1 no 6. evacuating and refrigerant charging station fitted with weighing scale 1 no 7. frost free refrigerator 1 no 8. ice candy plant 1 no 9. refrigerator 365 litre 1 no 10. refrigerator 185 litre 2 nos 11. storage type water cooler ( hot & cold ) 150 liters capacity 1 no 12. two stage rotary vacuum pump ( 3 or 4 cfm ) 2 nos 13. visi cooler185 liter 1 no 14. water cooler storage type 1 no 15. window ac 1 ton 1 no 1. battery charger 4 nos au 2. cut section working model of centrifugal clutch assembly 1 no 3. cut section working model of automatic transmission gear box 1 no 4. cutsection model of mock layout of a motor car electrical system working model. 1 no 5. diesel engine crdi 4 stroke for dismantling and assembling with swivelling stand 1 no 6. diesel engine 4 stroke vertical ( up to about 10 kw ) 1 no 7. diesel engine 6 cylinder in running condition 1 no 8. diesel engine 6 cylinder crdi 4 stroke running condition 1 no 9. drum brake assembly 2 nos 10. front axle ( rzeeppa joint ) with stand for dismantling and assembly. 2 nos 11. hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity each 1 no 5 sets 12. petrol engine ( 2 stroke ) cut section 1 no 13. steering assembly– working model 14. synchronous gearbox with stand for dismantling and assembly. 2 nos 15. trolley type portable air compressor 1 no 16. tyre changer machine 1 no 17. wheel balancing machine 1 no 18. functional / experiment model of different type of sensors. 1 no 1. motor generator ( dc to ac ) set 3 nos e 2. 2kva alternator with 3phase induction motor 1 no 3. ac phase wound slip ring motor with starter switch5 hp, 440 v, 3 phase, 50hz 1 no 4. ac squirrel cage induction motor 5 hp, 3 phase, 400 v with star delta starter 2 nos 5. brake test arrangement with two spring balance 1 no 6. dc compound motor with starter &switch 6 nos 7. dc generators –series, shunt & compound type 1 no 8. dc series motor ( 2.5kw, 220 v ) coupledwith spring balance load 3 nos 9. d.c. shunt generator with control panel2.5kw, 220v 3 nos 10. dc shunt motor 2.5 kw, 220 volts 3 nos 11. diesel generator set 2 nos 12. motor generator ( actodc ) 1 no 13. oil testing kit: 4 nos 14. oscilloscope dual trace 50mhz: 1 no 15. synchronous motor 3 phase, 3 hp, 440 volt, 50 hz, 4 pole, with all panel board accessories 4 nos 16. three phase transformer shell type 6 nos 17. three phase transformer, ( 5kva ) 2 nos 18. data acquisition system ( das ) 1 no 1. inter lock machine 1 no lgm 2. post bed sewing machine 1 no 3. sewing machine power operated ( heavy duty ) 1 no 4. cylinder bed sewing machine 1 no 5. sewing machine industrial type flat bed 2 nos 6. upper leather skiving machine 1 no 1. auto compression moulding machine 1 no plastic 2. automatic extrusion blow moulding machine 1 no 3. hand operated compression moulding machine with moulds 1 no 4. hand operated injection moulding machine 15 grams capacity 5. hand operated injection moulding machine 30 grams capacity 1 no 6. test equipment for plastic mfi 1 no 7. universal testing machine for plastic 1 no 1. 15 hp submersible pump set 8 stage 1 no lm 2. centrifugal pump coupled with mono block set 1 no 3. diesel engine 3.5 kw fitted with pump 1 no 4. circle cutting machine 300 mm 1 no 5. drilling machine bench ( sensitive ) to drill up to 13mm dia along with accessories 21 nos 6. drilling machine pillar0 20mm capacity with swivel table motorized with chuck and key 22 nos 7. guillotine shearing machine foot operated 1 no 8. double ended pedestal grinder 300 mm 4 nos 9. double ended pedestal grinder 250 mm 9 nos 10. power hacksaw machine 16” hydraulic 12 nos 11. seaming machine 1 no 12. slotter with all attachments 8 nos 13. profile projector 1 no 1. ss and sc center lathe ( all geared head stock ) 95 nos hm 2. tool room lathe s.s &s.c. ( all geared type ) 13 nos 3. horizontal milling machine 2 nos 4. universal milling machine 6 nos 5. vertical milling machine 2 nos 6. surface grinding machine ( hydraulic type ) 1 no 7. tool & cutter grinder 5 nos 8. universal cylindrical grinder with center height 130mm ( hydraulic typewheel head movement ) 1 no 9. universal cylindrical grinder with center height 150 mm ( hydraulic typewheel head movement ) 3 nos 1. sewing machine single needle lock stritch industrial model. 43 nos sewing 2. overlock machine 3 thread. 1 no 3. zig zag multipurpose machine. 1 no 4. double needle machine. 3 nos 5. button hole machine. 1 no 6. button sewing machine 2 nos 7. feed off the arm double needle 1 no 1. welding transformer with all accessories ( 400a, ocv60 100v, 60% dutycycle 2. welding transformer with all accessories ( 300a, ocv60 100v, 60% duty cycle ) 14 nos 3. d.c arc welding rectifiers set ( thyristor type ) with all accessories ( 400a. ocv 60 100v, 60%duty cycle ) 15 nos 4. gmaw welding machine 400a capacity ( inverter type ) with air cooled torch, regulator, gas pre heater, gas hose and standard accessories 4 nos 5. ac / dc gtaw welding machine with water cooled torch 300 a, argon regulator, gas hose, water circulating system and standard accessories 7 nos 6. air plasma cutting equipment with air compressor and all accessories. 2 nos 7. spot welding machineto15kva with allaccessories 10 nos 8. portable gas cutting machine...

Bharat Heavy Electricals Limited - Tamil Nadu

33114358 bhel / trichy invites applications for regd. from suppliers / manufacturers for supply of various items bhel trichy cast: aluminium, astm a 217 c12a castings, cast iron castings for windbox, feeder, coal nozzles ( sg iron castings up 850 kgs ) , castings for oil field equipments: carbon, alloy and stainless steel qcnrv castings, hemi spehrical dished ends ¿ grade hemi spehrical dished ends ¿ alloy steel upto gr 22 ) , die forgings for oil field equipments:, carbon, alloy and stainless steel, open forgings f91, f92, f92 forgings, closed die forged components forged finned elbow, forged flanges, formed fittings: large 12 and above, forged finned elbows, formed fittings: small 2 to <12 socket welded forged fittings, open forgings carbon, alloy and stainless steel except sa 182 f91, inconal fittings, inconel forgings for valves , investment castings for connectors, windbox sa 351 gr ch 20, sa 351 ck 20, investment castings, castings: malleable iron nickel based castings, non ferrous castings for feeder: is 617 4223, is 617 4450, is 305 gr ab1, astm b 148 gr 9c, non ferrous castings ( 0.5 to 200 kg ) open forgings for oil field, equipments: carbon, alloy and stainless steel, open forgings for hp bypass valves: carbon and alloy steel, formed fittings p91, f92 fittings, steel castings, sg iron machined castings for coal, nozzles, split collar for wind box: astm a 536 gr 654512 sg iron castings, close die forgings: carbon, alloy and stainless steel, open forgings for valves, carbon steel, alloy steel and stainless steel castings for valves name plate metallic, , , fasteners: hsfg bolts and nuts as per tdc:5:211 / 01, , precsn bolts, studs, screws and nuts dip coat paint, thinner and special additive, h.r. aluminium paints grade i h.r. aluminium paints grade ii , conventional paints and thinners, epoxy based paints and thinners, epoxy finish paints and thinners, special primer paints and thinners seamles p91 / p92 pipes, alloy steel pipes: sa 335 p11, p12, p22, od 88.9 to 1016 mm, 6.02 to 135 mm thick carbon steel pipes: sa106 gr b, c; od, 88.9 to 1016 mm, 6.02 to 135 mm thick pipes & tubes ( welded stainless steel, erw / saw pipes : api 5l gr b, od 219.1 to 1168 mm, 4 to 14.3 mm thick, erw black pipes: is 1239, nb 80 to nb 150, light, medium and heavy thick, seamles p91 / p92 pipe alloy steel pipes: sa 335 p11, p12, p22 od 88.9 to 1016 mm, 6.02 to 135 mm thick, carbon steel pipes: sa106 gr b, c; od 88.9 to 1016 mm, 6.02 to 135 mm thick, alloy steel rounds for valves:, 21crmov57, sa 193 b7, a322 gr 6150, sa 193 b16, sa 182 f22 cl3, aisi 4140, aisi 1040, : dia 22 mm to 300 mm, brass sheets, 0.2 mm and 1.0 mm thick, 17% gr. ss ( othron steel ) rods, astm a182 f430, dia 25 mm to 200 mm, special alloy steel rods for hplp valves alloy steel plates to grade sa387 gr91 cl alloy steel rounds to grade sa182 f91, stain l ess steel rods, dia 25 mm to 250 mm of different specs including sa 182 f304, sa 479 304, sa 182 f316, a276 410, , aisi 410, a582 416, a276 420, a565 616, sa 564 630, a182 f6a cl3, 17 4 ph, special stainless steel rounds: x 19 cr mo vn bn 111 6010 dia 52mm, 56 mm and 125 mm, alloy steel rounds / blooms, alloy steel plates: sa 387 gr 12 cl 2, gr 22, gr 91 4 mm to 120 mm thick., alloy steel rounds: sa 182 f12, f22, sa193 b7, b16, astma600t4 dia 6 mm 200 mm, carbon steel plates boiler quality ( sa299 gr a ) 65 mm to 190 mm thick, carbon steel plates boiler quality ( sa515 gr 70 ) 5 mm, 6 mm, 63 mm to mm thick, carbon steel rounds / blooms, structural quality plates bsen 10025 3 / s420n, a36 75 mm to 155 mm thick, structural quality plates carbon steel is 2062 e250 gr a, b / is 513 osk, and dsk / is 1079 0.9 mm to 63 mm thick corsn resi. steel sheets and plates , , astm a 588 gr a, corten a, jis 3125 2.5 mm to 5.0 mm thick angle, channel, beams heavy section ( a 130 200 mm, b 400 600 mm and c 300 ? 400 mm ) , angle, channel, beams light section ( a 40 65 mm, b 125 200 mm and c 75 ? 100 mm ) , angle, channel, beams medium section 75 100 mm, b 250 350 mm and c 200 ? mm ) , parallel flange beam / u beam / h beam 150 mm to 700 mm, carbon steel boiler quality rounds: sa 105 20 mm to 200 mm dia, . carbon steel rounds: is 2062, is 1875 4 8 mm to 100 mm dia. stainless steel sheets and plates: sa 240 tp 300, 400 series 0.6 mm to 50 mm thick, stainless steel rounds: sa 479 tp 300, 400 series, sa 182f316 6mm to 100 mm dia., tmt bars dia 8 mm to 40 mm weld stud / ferrules, ifm gas ignitor, 0.25 kw heat capacity, length of ignitor 900 to 1265mm, 110 v / 240 v, ac, regulating duty electrical actuator ( for dampers ) , transmitter ( pressure / flow / temp ) actuator: pneumatic ( open / close type ) , regulating duty pneumatic actuator ( for dampers ) proximity switch , bdt / tubular level gauges, electrical accessories for valves, fractional hp motor for soot blowers, panels: plc based control system, cast aluminium junction box ( non flame proof ) , compensating / extension cable, cable dressing materials, mpgfc cpu, brass cable gland and cable gland adapter, gi perforated / ladder type cable tray cable tags, cable lugs, pvc insulated copper control cable frls ) , pvc insulated multipair instrumentation cable ( frls ) , frp junction box, flame scanner head assy ( safe flame ) , flame scanner cable, thermoplastic / elastomeric / equiv alent, material insulated double shielded copper, instrumentation cable ) , flame scanner assy ( industrial boilers ) , flame scanner head assy test kit flame scanner head electronics, mpgfc i / o modules / mp based gr. feder control, mpgfc kbd and ps / mp based gfc key, board and power supply, bhelfeed20s modules, electrical panels: ac / dc distibution, ptfe insulated and outer sheathed, extension cables, mpgfc rack, pcb and accessories, vfd controller, wired modular panel local control, panel, weighing module, wired modular panel remote , control panel, airfilter regulator, sheet steel junction boxes, starter / cntrl boxes: dc and ac local starter / mill fire, flame proof boxes ( cast aluminium ) galvanized sheet junction box, electrical actuator, motor control centre / power control centre stainless steel junction boxes, ash level switch, , acoustic pyrometer, modular type cabinet, bottom ash load cell bhelvision: electrical accessories, cctv system for furnace flame, viewing, gravimetric feeder control modules electronic modules for flame scanner system, electronic modules for acoustic, steam leak detection ( asld ) system electronic modules for electronic, water level indicator ( ewli ) , pressure switch for electromatic releif valve, electronic water level indicators fluegas analyzers ( dilution probe ) flue gas analyzers, smoke density: opacity / particulate measurements fluegas analyzers: oxygen measurement at boiler eco. inlet fluegas analyzers: sox / nox hot extraction type flow nozzles furnace flame viewing camera system and thermographic analysis system dp gauges pressure gauges temperature gauges signal isolator ( i / p converter ) local instrument enclosure passenger and goods elevator local instrument rack mass flow meter metal temperature measurement thermocouple process thermocouples and rtds with thermowell orifice plate assy purge meter ptfe insulated multipair instrumentation cable erv controller and control station steam and water analysers online carbon in ash analyser system vibration monitoring system for motor / fan bearing xlpe insulated lt power cable ( copper and aluminium ) coal motion monitor sensor cable assembly digital tachometer feeder belt motors: weather proof / flame proof panels for feeder integral cabinet fibre optic cable and lens barrel assy. calibration kit for solid state feeders copper / ss tube for instrumentation application decibel scanner unit with pc and software for asld system micro switch for gravimetric feeder pressure and dp swithces pressure gauges critical application pressure switches position transmitter for quick closing non return valves electrical control panel for soot blowers limit switches push button station, boxes etc for soot blowers solenoid for electromatic relief valves solenoid for hp bypass valves sonic tube assy and sensor housing drum saddle slide bearing plate: ptfe slide bearing on one side and the mirror polished ss sheet on the other side. load bearing capacity upto 200 kg / mm2 soot blower pressure reducing valve fuel oil control and trip valves control valve: high pressure steam application gun metal valve hp fill and purge filter assembly intrascope nitrogen blanket system high pressure startup control valve direct water level gauge refractory for cfbc boiler ceramic wool castable / crushed refractory insulation: calcium silicate slab / block / pipe electro forged floor grills long span fire bricks wool mattress / rtd / pipe section pourable insulation sealing compound ss wiremesh rope woven wire cloth stainless steel steel glazed windows cd. plated / galvanised fasteners pre painted galvanised sheets for boiler roof hea ignitor assy ( oil / gas ) solenoid valves ball valves ( fire safe design ) trip valves strainers: simplex goggle valve high pressure hoses ( dynamic pressure of 200 bar, static pressure of 290 bar, proof test pressure of 552 bar max, bursting pressure of 1103 bar max ) isolation valves / knife edge gate valves light duty limit switches gear pump with motor ( drain oil ) self actuating valves sump pump motor assembly speed regulator steam trap y type strainers neoprene hoses mill seal air filter assembly oil accumalator ( fuel oil ) actuator: elec. open / close ( damper / gates ) scanner air fan ( with dc motor / ac motor ) scanner air filter elements dynamic shaft seals ss flexible hoses graphite alloy damper bearing and bushings 400 deg c operation butterfly valves ( wafer design ) drag link chain feeder gaskets for coupling rockwell / sleeve couplings variable orifice victaulic / pipe couplings heat resistent glass ( pyrex glass dia 109mm, 5 mm thick, violet / light colour to withstand 500 deg c ) metallic expansion bellows non metallic expansion joints slide bearing plates teflon slide bearing plate gravimetric feeder assembly solenoid valve ( boi ) boiler circulating water pumps gravimetric feeder components frp cable trays instrument fittings: brass / ss double compression fittings, cs / as welded fittings, gi threaded fittings teflon hose ( ss braided, flexible ) furnace maintenance platform handling equipment: electrically operated trolly with hoists handling equipment: manually operated mobile platform quick errect scaffolding ( aluminium ) quick erect scaffolding system steel actuator for full bore valve pneumatic actuators for quick closing non return valves airset ( mech ) / air filter / regulator anti seize : spray lubricant head pulley bush bearings coal valves clad roller brg. assy strainers: duplex feeder components assembly fittings like male stud olive coupling / elbow / tee, bleeded plug, bulk head union feeder light fittings gaskets gasket eliminator / sealant fuel oil ( triple screw pump ) springs link chains o rings oil seals plug valves metallic seated high pressure rubber hoses sintered flange bronze bushes slip on pipe coupling ss spiral wound gasket tadpole tape fully built electric bus supply of power assisted safety valves special bearing for oil field equipment isolating ball valves pneumatic actuated full valves boiler water recirculating pump chains for soot blowers sdm: fully machined ofe castings machined components for valves zinc and xylan coated fasteners for oil field equipment plc panels for soot blower corrugated al sheet air / oil cylinder for quick closing nrv sdm:kgv:elastomers elastomers for oil field equipment sdm: 12 point cap screw flow bean for oil field equpment feed back transmiter high pressure filter circlips for feeders glass globe / light fitting for feeder fabricator metal component gear box and clean out conveyor drive gear box with motor for soot blowers gear box for valves special glass for water level gauge accumulatars accessories hp bypass system high tensile fasteners limit switch boxes premium threaded ( fox, acme, vamtop, etc., ) body hanger and adaptors non asbestos packings non metallic end covers drive belts pulleys for temperature probe o rings and oil seals aluminium sheet: plain / corrugated air cylinder open / close, retractor assembly special packing set for full bore valves limit switches for quick closing nrv ring joint gasket ( api ) ultrasonic digital thickness gauges with accessories sintered bronze bush soft iron gaskets and sealing rings silencers for safety valves swagelock fittings coil springs for safety valves coil springs for safety valves with ibr tc special tools for oil field equipments anhydrous ammonia hose agitator for waste ammonia dilution system ammonia injection skid butterfly valves for dilution air and ammonia injection system dilution air fan & motor assembly including filter de dusting system dosing tank & pumping system dilution air heater ( electrical ) expansion bellows emergency eye wash & safety shower frp grating hydraulic jack for scr cart ammonia injection control valve ammonia knife edge gate valve anhydrous ammonia pump skid dilution air heater ( steam ) & accessories spray nozzle for spraying sealing rings, retainer rings, drive screws safety selector for tank relief valve spray water self regulating valve fibre glass tadpole tape ammonia trip valves ( ball type, manual, pneumatic & electrical ) anhydrous ammonia truck unloading skid wind indicator water level gauge rings and washers excess flow valves & check valves tunguston carbide balls, bearings, etc for ofe ( oil field equipment ) spiral wound gaskets oil supply unit for hp bypass system teflon o rings, packing rings etc. accumulator manifold keys, pins, washers etc. valve diaphragm actuator valves elec actuators hydraulic actuators & accessories hydraulic power unit proportional valve valves special ( iq ) actuators throttle device for hydraulic power unit washers and circlips coated abbrasives adaptors api gauges te abrasives polytap hss circular saw bi metal band saw blades te boring, facing head bta tools carbide burrs carbide tipped circular saw disc slitting wheels thread gauges grinding wheels shelf life grinding wheels hss cutting tools carbide cutting tools hacksaw blades high q carbide cutting tools measurnig instruments letter and number punchs special cutters spade drills stellite turning inserts spiral fluted tap symmetrical carbide drills threading taps threading tools tube expanders wrenches indexable carbide drills vdi holders zircon belts alloy steel flats carbon steel strips tubes: erw black is 1161 yst 240 and bsen 10305 alloy steel tubes: sa 213 t11 / t12 / t22 / t23 / t91 / t92 boiler quality carbon steel tubes: sa 210 gr c , sa210 gra1, sa192 boiler quality stainless steel tubes: sa 213 tp 347h tp316 / tp304h / s304h boiler quality alloy steel tubes t91, t92 fused saw flux for drum welding fused saw flux for tube to fin welding gtaw wire for t92 er80s b2 bulk pack gmaw wire gmawwire ernicrfe 7a gmaw wire er 70s a1 gmaw wire er 80s b2 gmaw wire er347 gmaw wire ernicr3 gmaw wire er90s b9 gmaw wire er70s 6 gmaw wire er80s g 1cr mo gmaw wire er90s g 2cr mo gmaw wire for t23. saw flux p91 saw flux for sa335p92 saw wire for sa335p92 weld:ss overlay flux f48p2 em12k submerged arc welding flux for structural application saw flux struct.weld gtaw rod t92 / p92 gtaw rod er309l er 70s a1 gtaw rod er 80s b2 gtaw rod er 90s b3 gtaw rod gtaw rod tig er347 gtaw rod tig ernicr gtaw rod er90b9 er80s d2 gtaw rod gtaw rod super 304h smaw electrode e7018 a1 smaw electrode e8018 b2 smaw electrode e9018 b3 smaw electrode e9015 b9 smaw elecd t92 / p92 smaw electrode e6013 smaw electrode e7018 smaw electrode e7018 1 e7018 smaw electrode flux cored wire e71t 1 flux cored wire e309t0 1 fcaw wire e309lmoto 1 flux cored wire e81t1 b2 flux cored wire e91t1 b3 bulkpack :e551t1 b2c smaw:hf electrode ecocra smaw electrode ecocr e smaw electrodes enicrfe3 smaw electrode smaw ss electrodes ( e308 16 ) smaw ss electrdes low carbon ( e308l 16 ) smaw electrodes e309 16 smaw electrodes e310 16 smaw electrodes e316 16 smaw electrodes e316l 16 smaw electrodes e347 16 hayness alloy 25 ( ha 25 ) filler rod hayness alloy 21 ( ha 21 ) filler rod ercocr a rod hard facing powder type cocr a hard facing powder type cocr e el 8 saw wire saw wire eb3 wg:wire:saw er430 saw wire eb2 saw wire ea4 saw wire em12ksaw wire eb 9 er 309 saw wire er 347 saw wire weldwire saw em12k...

Southern Railway - Tamil Nadu

33008736 supply of design, supply and commissioningdesign, supply and commissioning,design, supply and commissioning of hydraulic power pack for single acting hydraulic jack of make vanjax vxrc 30/150 & vankos rc sp ehp 30/150 . power pack consists of motor: 2 hp with starter, tank with trolley wheels:25 30ltr, valves: hand operated dcv suitable for 700 bar manifold block with ng 6 size valves, relief (safety) valve, pressure gauge, check valve. pump: piston pump 0.7 lpm, with 3 mtr jack hose with quick coupling arrangement, the hydraulic oil:30 lts, vg 68 mineral oil. power pack should be suitable to operate the single acting jack 30t capacity @700 max working stroke 150 mm in 40 50 sec. note : 1. the firm should commission the power pack with available 30 t single jack of emu workshop, tambaram. 2. after commissioning the power pack, the firm should impart training to railway staff. 3. maintenance manuals , spare parts lists with prices and other technical details are to be submitted along with supply. 4. warranty : one year. => limited...

Southern Railway - Tamil Nadu

31952767 supply of traction rod bush assemblytraction rod bush assembly,supply, erection & commissioning of traction rod bush assembly fixture consisting of double acting hydraulic jack, hand pump, pipe etc, along with complete fixture for wag 9 locomotives as per els/kzj specification no. c/els/kzj/spec/07....

Southern Railway - Tamil Nadu

31952319 supply of 50 ton aluminium hydraulic jack50 ton aluminium hydraulic jack,50 ton aluminium hydraulic jack set consisting of 05 items : 1.single acting, spring return aluminium cylinder capacity: 50 ton, stroke: 150 mm, qty 01 no. 2. single acting, two speed hand pump, usable oil capacity: 2294.1 cu.cm, . qty 01 no. 3.heavy duty hydraulic rubber hose. hose length: 6 feet, hose i.d. : 1/4 inch, qty: 01 no. 4. hydraulic pressure gauge. qty: 01 no. 5. gauge adaptor. qty: 1 no. make: i torq or aero boom or good way or vankos & co...

Chief Construction Engineer - Tamil Nadu

31536334 ocb / ckicp / hrs eq 1 / 02 procurement of equipment for hrs phase 1 vacuum viscometer bath , towards the supply of vacuum viscometer bath cannon manning or equivalent capillary viscometers made of borosilicate glass, calibrated with constant certificate for absolute viscosity of bituminous materials and capable of conducting tests as per is 1206 ( part ii ) 1978 and astm d2171m complete with factory calibration certificate. standard accessories: • differential mercury manometer made of borosilicate glass / digital vaccum system upto 650mm hg, graduated from 40 0 40cmsor 0 80cms with lc of 0.5mm, duly guarded with unbreakable perspex cover1 no. • high vacuum pipelines, one meter length with silicon viscometer2 nos • high performance kinematic viscometer bath: designed for 24x7 duty cycle andis used to maintain the correct constant temperature for estimating viscosity from below ambient to 160°c 1 no • silicone thermal fluid suitable for temperature up to 250°c20 litres • cannon manning or equivalent tube size: 12 viscosity range ( poises ) 360 80002nos • cannon fenske or equivalent reverse flow capillary viscometers tube sizes: 6 viscosity range ( cst ) 60 1000 1 no • thermometer: mercury in glass, ip5cfor kinematic viscosity1 no including warranty for the period of 12 months from the date of supply or installation whichever is later. , universal digital penetrometer , towards the supply of universal digital penetrometer capable of conducting test as per astm d5, and is 1203:1978 with the following features: • opto electronic / laser / lvdt based depth detection & measurement system • display resolution of penetration depths in tenths of units ( 0.01mm ) • magnifying lens for adjusting needle tip / cone tip exactly on the sample surface. to be supplied complete with the following items for bitumen penetration, •weight of 50 grams 1 no. • penetration cup of 55mm diameter x 35mm height 1 no. • transfer dish 1 no. • penetrometer needle 1 no. • needle holder 47.5g ± 0.05g 1 no. • thermometer astm 17c ( +19 to 27 °c ) 1 no. including warranty period of 12 months from the date of supply or installation whichever is later. , digital ductility testing apparatus , towards the supply of digital ductility testing apparatus capable of conducting the testsas per astm d113 with the following features: • cooling arrangement with required compressor provision • equipped with testing three specimens simultaneously • electric pump circulator and heater. • the temperature is controlled by digital temperature controller with two rates of travel are to be provided i.e. 5cm / min and 1cm / min. • suitable for operation on 220v, 50 hz, single phase, ac supply. including warranty period of 12 months from the date of supply or installation whichever is later , rolling thin film oven , towards the supply of rolling thin film oven capable of conducting the test as per astm d2872 with following features: • low thermal mass rtd.;• over temperature safety cutout ;• double walled temperature cabinet • 16 gauge welded steel exterior;• 18 gauge corrosion resistant stainless steel interior • insulation with 89mm high density fiberglass ;• programmable microprocessor ul listed controller • 4 digit red led temperature display;• 4 digit green led for temperature set points • including thermal protection which prevents oven in event of control failure;• temperature range: ambient to 200deg c; • double exhaust vents;• needle valve for air flow adjustments;• air pressure gauge range ( 0 to 100 psi ) ; • heat exchanger 5 / 16 inch dia. copper tube;• electrical supply : 230v ac supply, 50hz single phase • dimension : 1016x660x915 mm;• estimated weight : 100 kg ;including warranty period of 12 months from the date of supply or installation whichever is later. , digital marshall stability apparatus , towards the supply of digital marshall stability apparatus of 100kn single speed for4” / 6” dia. samplecapable ofconducting the test as per ms 2 and is 17127:2019 including calibration certificate with the following features : •load frame, • holder pin, • power cable, • load transfer bar, • steel ball, • electronic kit indicator containing. load cell with adapter and cable. displacement sensor with cable • 4” / 6” dia. sample mould assembly with . rammer . extractor. round plate . dummy plate. handle pipe . breaking head. pedestal ( 4” / 6” sample ) including warranty period of 12 months from the date of supply or installation whichever is later. , california bearing ratio testing machine , towards the supply ofcalifornia bearing ratio testing machine capable of conducting test as per is 2720 part xvi with the following features: • compact, bench top design, rapid platen adjustment complete with stabilizing bar options for mechanical or electronic measurement • suitable for operation on 220v, 50hz, single phase, ac supply;• digital indicator ;• mode of display: micro controller multiline, alpha numeric lcd display for all simultaneous channel ( no need for channel selection ) ;• load cell, capacity: 50kn compression type;• three speed 1.5 mm / min, 1.25 mm / min & 2.5 mm / min, maximum: 110% of the rated capacity • sensing: strain gauges in full bridge configuration;• displacement transducer range: 0 20 mm with 3m long cable • sensing element: lvdt ;the equipment shall be supplied with ;•laptop computer ( minimum intel i5 processor, 8gb ram ) loaded with licensed microsoft windows 10 os ( lifetime free update ) – 64 bit;•ms office bundle software valid for 5 years and other suitable software for conducting all the above tests with recording and analyzing.;including warranty for period of 12 months from the date of supply or installation whichever is later. , automatic california bearing ratio test apparatus , towards the supply of automatic california bearing ratio test apparatus capable of conducting test as per is 2720 part xvi. with the following features: • motorized electronic with data acquisition system;• geotechnical software for testing, analyzing and reporting; • the software should allow selection of british / indian standards for analysis.; • tests are to be performed in si, imperial or metric units.; • test information is to be presented on menu driven screen.;• each package guides through the test procedures is to be in very user friendly way.;• a database setup to store and manage completed analysis records with ms access as default system.; • the software has to read the data format for analysis from data aacquisition system;• an option to enter the data manually and save; • with extensive search functions based on date of analysis, analysis done by different user accounts or search based on duration etc, for easy retrieval of old data.; • the default reports shall be automatically generated in crystal reports and to be printed directly.;• the reports shall be exported to word, excel or pdf formats.; • customizable report header / footer; • the inbuilt utilities include master unit conversation calculator, besides the normal and scientific system calculators.; • database backup and restore facilities ;• complete user activity logging ; special features and graphs for cbr analysis software • manual data entry facility ;•to find out cbr value in % at 2.5 mm and 5mm penetration.;• graph for load vs penetration ( top side, bottom side and both ) .;• graph correction facility ; • graph expand facility.; with software for the following tests •unconsolidated undrained triaxial test;•consolidated undrained triaxial test;• consolidated drained test; •direct / residual shear test;•cbr test;•one dimensional consolidation test;including warranty period of 12 months from the date of supply or installation whichever is later. , automatic soil compactor , towards the supply of automatic soil compactor capable of conducting test as per is 2720 part viii complete with the following features •motor driven mechanical compactor for soil compaction in 100 mm or 150 mm dia moulds. •two rammers with different stroke length that should travel across the mould and the table rotates the mould in equal steps on a stable base. •the number of blows per layer can be set at the beginning of the test. • rammer circular faced 50mm dia. adjustable to 2.6kg or 4.9kg weight •drop adjustable to 310mm or 450mm. •digital display for counting the number of blows. •the equipment should be suitable for operation on 220 v, 50 hz, single phase, ac supply including warranty period of 12 months from the date of supply or installation whichever is later. , automatic vicat’s apparatus , towards the supply of automatic vicat’s apparatus for setting time test on cement / mortar / gypsum conforming to en 196 3, 13279 2, 480 2, is 4031 part 4& 5, astm c191, c187 complete with the following accessories: • initial setting time needle 1.13 mm dia, 1 mm diameter needle mould •needle for final setting test; • cylindrical probe for consistency test; • accessory for needle continuous cleaning and in water testing ; touch screen display• graphic printer; • usb port for data storage, export to pc and firmware upgrade and ethernet port for pc / network communication and network mode to independent units; • minimum 16 gb internal permanent memory on sd card •to be supplied complete with necessary software for remote pc control including lan cable to be supplied complete with the following features • fully automatic test cycle; • easy re call of test settings from test profiles database • easy programming of customized test including: test start delay, penetration points positions, manual or automatic penetration rate, free or driven mode, holding intervals, automatic end test detection.; •automatic measurement of initial and final setting time;• easy calibration menu including warranty period of 12 months from the date of supply or installation whichever is later. , digital flexural testing machine , towards the supply of digital flexural testing machine ( 100kn ) conforming to is 516, bs: 1881 and astm c78 with the following accessories: •suitable frame ; •double action hydraulic pump ; •self aligning roller assembly ; •hydraulic jack provided with retraction spring for testing beams of 100x 100x500mm and 150x 150 x 700mm;•suitable for operation on 220v 50hz, single phase, ac supply including warranty period of 12 months from the date of supply or installation whichever is later. , automatic blaine’s apparatus , towards the supply ofautomatic blaine’s apparatus capable of conducting tests conforming to astm c204, en 196 6, is:1727, 4031, 4825 with the following features: •automatic control of the movement of fluid until the upper mark.;•automatic sensing of the upper & lower marks ensuring error free repeatable measurement of the time taken for the liquid column to fall.;•automatic measurement of temperature during the test using a probe including automatic correction of formula for calculation of the blaine value per is: 5516 with variation in temperature.;• facility to operate in either standalone mode or through a computer controlled system complete with software login facility.;•report generation based on date / time. user type & type of cement in excel or equivalent format. including warranty period of 12 months from the date of supply or installation whichever is later. , rebar locator profometer 650ai , towards the supply of rebar locator profometer 650ai capable of conducting corrosion measurement conforming to astm c 876 consisting of profometer with the following features: •touchscreen, •universal probe with probe cart, •probe cable 1.5 m ( 5 ft ) , •power supply, ;•usb cable, dvd with software; •documentation, •activation key; •carrying strap and carrying case ; •upgrade kit to profometer corrosion consisting of interface box, ;•cable coil of length 25 m ( 82 ft ) with clamp, ;•dvd with software, •documentation and carrying case;•profometer corrosion rod electrode, with spare parts, cable including spade terminal adapter and copper sulphate ( 250g ) ;•profometer corrosion one wheel electrode, with telescopic handle, encoder, cables, spare parts, tool kit, copper sulphate ( 250 g ) , citric acid ( 250 g ) etc complete ; including warranty period of 12 months from the date of supply or installation whichever is later. , multipurpose universal testing machine , towards the supply of multipurpose universal testing machine 2000kn servo controlled machine capable of conducting tests conforming to is 1828 part 1:2005 with the following features: •hydraulic power system, • microprocessor control unit, ; • clearance for tensile test shall be 50 850 mm; • clearance for compression test shall be 0 700 mm ; • user interface with large graphic display with keyboard; • data acquisition testing system and related legal and licensed version of interactive software. with the following accessories;• 2000kn loading unit; • servo pump system ;• clamping jaws for round specimen 08 70mm; • clamping jaws for flat specimen 0 40mm; • clamping jaws for ht strand wires 12.7 and 15.2mm;• bend test 180 degree attachment; • bend re bend test attachment ; • electronic extensometer with 25mm & 50mm gauge lengths & 600 mm forht strand wires; • shear test attachment 6, 8, 12, 16, 20mm;• shear test attachment 25, 30, 35, &40mm ; • flexure test attachment; • wire rope test attachment 0.12 13.2 mm;the servo pump with the following features; • standalone close loop automatic control console to perform tests under control of: load / stress and displacement by suitable transducers.• the rate of strain shall be adjustable between 0.00025 / s and 0.0025 / s and rate of stress 1 to 50 n / mm2 per second.including warranty period of 12 months from the date of supply or installation , digital compression testing machine , towards the supply ofdigital compression testing machine 2000 kn plates and accessories conforming to is 516 & is 14858:2000. with the following features: •digital indicator having 4 digits display calibrated in kilo newton ( kn ) and preset to maximum load capacity fitted with micro switches.;•electrically operated pumping units provided with control knob to adjust the pace rate and provided with a pace indicator to indicate pace rate on a bar graph.;•the pace shall be controlled manually while the test is in progress including warranty period of 12 months from the date of supply or installation whichever is later. , universal testing machine , towards the supply ofuniversal testing machine ( 1000kn ) capable of conducting tests conforming to is 1828 part 1 2005 with the following features; • hydraulic jaw set with a resolution of 0.01kn ;• clearance for tensile test shall be 50 850 mm; • clearance for compression test shall be 0 700 mm ;• clearance between columns 650mm, • ram stroke: 250mm ;• piston speed at no load should be 0 50mm / min• fully enclosed and protected load measuring system. load frame with rigid construction.;• motor driven threaded columns for up / down movement of lower crosshead for quick change over of specimen, grips and attachment.• power pack should generate a maximum pressure of 200 kgf / cm².;• system should have high precision, sealed and accurate pressure transducer mounted in thehydraulic pressure line of the loading unit;• system should have ergonomically designed micro process unit selection for load, displacement.;• results should include load vs displacement curve, maximum displacement, uts, %elongation, youngs modulus and proof stress; system should include the following accessories:;• clamping jaws for round specimens 8 25mm, 25 45mm; • clamping jaws for flat specimens thickness: 0 40mm; • flat specimen width: 70mm for tension test, ; pair of compression plates;• electronic extensometer strain gauge type with gauge length 25mm and 50 mm; • brinell test attachment, • bend / rebend test attachment , • flexural test attachment. system shall be supplied with following features:• software should have the features for data analysis like mean deviation, frequency distribution, skew diagram, histogram and graph.;• system should be calibrated in accordance with bs:1610 and is standards and it should comply with grade a of bs 1610:1964 and grade 1 of is: 1828 1991.;• power supply: 440v, 50hz, three phase, ac supply. • computer and printer should be supplied with the system having minimum specifications as follows; • i5 or better, 4 gb ram, ;•processor, 256mb , 250gb hd drive, cd rom drive, ;•mouse or pointing device and keyboard supported by windows 10 pro 64 bit and ms office bundle.;• monitor that supports 1024x768 resolution and 32 bit color, 2 usb serial port adapter per machine;• windows compatible sound card and speakers ( for audio playback ) • additional usb ports for measuring devices, barcode scanners, printer;• one integrated serial port ( not usb ) where possible, lan card for connecting with electronic panel .;including warranty period of 12 months from the date of supply or installation whichever is later. , desktop systems with licensed latest windows os 64bit , towards the supply of desktop systems with licensed latest windows os 64bit with the following futures: • genuine window 10 pro 64 bit ;• intel core i5;• 8 gb ram;• 1 tb harddisk ;•2gb graphics memory ; •19.5 inches monitor;including warranty period 36 monthsfrom the date of supply or installation whichever is later. , multi functional plotter , towards the supply ofmultifunctional wide format colour plotter, • size a0 to a4 with licensedsoftware; including warranty period 60 months from the date of supply or installation whichever is later. , video camera unit , towards the supply of drone camera with the following specification and accessories: • aerial video recording & photography, ;• sensor size of 1 / 2.3 inches, ;• cmos, optical zoom of 6x, ; • max speed 50 to 55 mph with flight time of 27mins, ;• 10 million pixels, • remote distance of 5 to 7km control range with fpv operation, ;• 2control channels, • app controller connectivity, ;• 4k hd video recording, • digital video zoom, ;• d log m and hlg hdr for high dynamic range recording and 10 bit support. • footage that is suitable for high end grading and editing applications; including warranty period of 12 months from the date of supply or installation whichever is later. , towards the supply of 4k professional camcorder with super 35 camcorder kit with zoom lens or equivalent, with the following specifications / accessories: • e mount locking sys mechanical adapter, • variable electronic neutral density nd 2 to 7 stops filter, • built in mic viewfinder and short gun mic holder mount with latest rolling shutter technology, • wi fi adaptor, • controllable zoom focus iris & white balance as well as recording functions, control with mobile device., internal recording in both dci 4k & uhd 4k upto 59.94 frames / sec, • camera tripod, • carry case including warranty period of 12 months from the date of supply or installation whichever is later. , still camera , towards the supply of slr cameraseries or equivalent with selectable lenses with the following specification / accessories: • 20 mp fx cmos sensor; • 14fps shooting ( video mode ) ; • 4k ultra hd video recording at 30fps • built in wi fi ; • bluetooth and gps; • touch screen lcd monitor; • expeed 6 image processor or equivalent; • 64gb xqd memory card 2nos, • shoulder bag; • zoom lens200 500mm f / 5.6ed or equivalent; • normal 50mm; • wireless ttl flash unit; • free wave wireless remote including warranty period of 12 months from the date of supply or installation whichever is later. , video editing unit , towards the supply and installation of video editing unit consisting intel core i7 10th gen processor ( windows platform ) with asus b250m plus motherboard or equivalent with the following accessories: • 64gb ddr4 ram; • 350gb ssd wd hdd ; • 2tb sata wd hard disk ( 2nos ) ;• w5000 g force8gb / asus game engine or equivalent ; • cooler master cabinet or equivalent ( industrial cabinet ) • cooler master 750w smps or equivalent, digital intermediate panel board; •keyboard and mouse, editing console table; • blue ray writer; • led monitor 2 nos ; • television 32inchs preview monitor ; • monitor speaker 2 nos; • hdmi splitter with cable ( according to the length ) • speaker stand 2nos, interconnecting cables ( signal / pwr / bband / ethernet / hdmi , sound proof & acoustic ( sq ft rate 1200 / sqft ) ; • lightings / emergency light.; • software required • fcp / premier pro ( any one ) ; • photo shop & after effect ; •color correction software windows 10 / 64 bit pro and ms office bundle. including warranty period of 12 months from the date of supply or installation whichever is later. , sound recording editing unit , towards the sound recording editing unit consisting intel core i7 10th gen processor ( windows platform ) with asus b250m plus motherboard or equivalent with the following accessories: • 64gb ddr4 ram; • 350gb ssd wd hdd ; • 2tb sata wd hard disk 2 nos; • w5000 g force8gb / asus game engine or equivalent •cooler master cabinetor equivalent ( industrial cabinet ) , • cooler master 750w smps or equivalent • keyboard and mouse • blueray writer • 22 inch led monitor or equivalent 2 nos • television 32inchs preview monitor, • ssl soundscape 32 daw hardware •digital portable mixing console o3d • audio interface ( audio card ) • 1000c condenser 2 nos • headphone 3 nos • studio monitor speaker 2 nos • hdmi splitter with cable ( according to the length ) , • mic stand 2 nos • speaker stand 2 nos • working table ( mixer and console table with rack ) • console and studio chairs, pop filter ( blow cutter ) • interconnecting cables ( signal / pwr / ethernet / hdmi • sound proof & acoustic for console and vox room ( @ sq ft rate 1200 / sqft ) • vox room 200 sqft • console cum engineer room 250 sqft • air condition plant4ton ( 2x2 ) , lightings / emergency light / sign boards softwares required are: • protools ver.10 or 12 & sscape daw software ( digital audio workstation ) or equivalent • noise cleaning software • window 10 pro 64bit and ms office bundle includingwarranty period of 12 months for from the date of supply or installation whichever is later. , multifunctional colour copier machine , towards the supply ofall in one color printer, digital color mfd ( print / copy / color scan / stores / scan to e mail and folder ) with the following features: • all in one color printertowards the supply ofall in one color printer, digital color mfd ( print / copy / color scan / stores / scan to e mail and folder ) with the following features: • 30 cpm / ppm copying / printing speed • up to a3 size • digitalinbuilt network printer • copier color • duplex printing & copying • dadf ( duplex automatic document feeder • 3 gb ram • 250gbhard disk • 2auto trays ( 550+550 ) sheetscapacity • 100 sheets bypass • 200x1200 dpi resolution • 1.5kw or less power consumption • 25% 400% zoom ration • rotate collate •toner yield – black – 36000 copies; •color ( c / m / y ) – 19000 copies each •drum yield – black –84000 copies •color ( c / m / y ) 66000 copies each •machine life 10 lakh copies, •value addition: movable trolley with shelf and 2kva stabilizer including warranty period of 12 months for from the date of supply or installation whichever is later. , towards the supply of all in one wireless colour printer ofink tanktype color printer with all in one ( print, scan, copy ) functionality with iso standards with the following features: • • wi fi connectivity • usb, with suitable printing application. • compatible withwindows 10, windows 8.1, windows 7 sp1. • power requirements of 200 to 240 v • 50 / 60 hz • 1.2 inch lcd diplay on printer ( mono ) • 8.8 ipm ( black ) • 5 ipm ( colour ) • as per iso standards. page size supported 4.0x6.0 till a4 / letter / legal / a5 / b5with • print resolution of4800 x 1200 dpi, • compatible ink bottle gi 790 ( bk ) , gi 790 ( cyan, magenta, yellow ) , • page yield of 6000 pgs ( bk ) , 7000 pgs ( color ) – with 1 set of all 4 ink bottles inside the box ( as per iso standards ) including warranty period of 12 months the date of supply or installation whichever is later. , towards the supply of laser printerwithall in one ( print, scan, copy ) functionality with the following features: • with the following features: • printer output mono ( black ) . • usb 2.0 connectivity. • wi fi, with software for printing. • 6.9cm bw lcd display panel. • compatible with 32 / 64bit windows 10, 8.1, 8, 7, vista, windows server 2012 r2 ( 64bit ) , windows server 2012 ( 64bit ) , windows server 2008 r2 ( 64bit ) , windows server 2008, windows server 2003 r2, windows server 2003, • print language ufr ii lt, pcl 6; • device memory 512mb • duplex • page size supported a4, b5, a5, • legal, letter, statement, executive, • government letter, government legal, • foolscap, indian legal • custom ( minimum 76.2 x 210mm to maximum 216 x 356mm ) • print resolution 600 x 600dpi • cartridge 337; page yield 2400 pages. • as per iso standards, ( digital multifunction laser printer, black, standard ) including minimum warranty period of 12 months from the date of supply or installation whichever is later. . , garden maintenance machine , towards the supply of brush cutter with the following features; • with the following features; • powered by42.7 cc with 2 stroke air cooled engine, • fuel tank capacity of 0.9 ltrs., • dry weight 8.0 kgs, • cutting tool steel blade, • nylon head & 15 metre nylon rope including warranty period of 12 months from the date of supply or installation whichever is later. , towards the supply of lawn mower with the following features: •powered by electric motor, ;•3 phase / 440v, ;•5 hp / 2880 rpm, ;•cutting width of 45 cm, ;•cutting height of 10 100 mm ( 6 stages ) , ;•straight blade•steel cutting deck , ;•cable length 4;including warranty period of 12 monthsfromthe date of supply or installation whichever is later. , vaccum cleaner , towards the supply ofvacuum cleaner with the following features: • 230 240 / 50hz voltage, • 1350 w power, • 54lps airflow with suction power of 22 kpa, • tank volume of 35 litres, • dimensions cm ( lxwxh ) 36x36x76, • weight 9 kg including warranty period of 12 monthsfromthe date of supply or installation whichever is later , laptop and desktop computers , towards the supply of laptop with the following specifications; • intel core i7 1165g7 • 8gb ddr4 • 512gb ssd • 15.6” ( 1920x1080 ) • 2 gb dedicated graphics / hd • webcam backlit keyboard • finger print reader • wifi 6+bt 5.0 •maximum weight of 1.8kgms office licensed software. • win 10 pro – 64 bit ms office bundle including warranty period of 36 monthsfromthe date of supply or installation whichever is later. , towards the supply of desktop systems with licensed latest windows os 64bit with the following futures: • genuine window 10 pro 64 bit • intel core i5 • 8 gb ram • 1 tb harddisk • 2gb graphics memory • 19.5 inches monitor including warranty period 36 monthsfrom the date of supply or installation whichever is later. , towards the supply ofms office 2019 standard version , calculation of subtotal, gst and total amount carried out by system automatically , basic cost of value put to tender as per estimate , add gst at 18% , total value put to tender , negotiated percentage , final negotiated value , add gst at 18% of final negotiated value , total value of contract including 18% of gst , basic cost of value put to tender as per estimate , quoted rate in figures ( total value of contract including 18% of gst ) ...

Southern Railway - Tamil Nadu

31318472 supply of facilities for dismantlingfacilities for dismantling,facilities for dismantling and assembly of traction rod assembly associated tooling along with accessories as enclosed in annexure. traction rod bush assembly fixture consisting of double acting hydraulic jack pump, pipe etc. along with complete fixture to adtranz drawing no. v01s75 hb for wag 9 loco. make: power team/vankos/aeroboom....

Southern Railway - Tamil Nadu

31245572 supply of procurement of supply and fitment for orione hydraulic jack.procurement of supply and fitment for orione hydraulic jack.,supply and fitment of the following spares and service for orione hydraulic jack & pump 1. spare repair kit consisting of ram seal, o ring, inner tube piston seal and wiper ring for orione 20ton hollow jack. model : osh 20 100 2. orione hyd. hand pump of relief valve, suction & delivery valves and its accessories model ohp 2p4 2 5 3. operating handle for the orione hyd. hand pump model : ohp 2p4 2 5 4. pressure gauge 0 1000 bar with glycerin filled & stand pipe for connecting the pressure gauge with hyd. pump 5.hyd.high pressure hose 2 mtrs length with 3/8bsp female swivel nut on both sides to connect jack and pump. w/p @700 bar. 6.quick change coupler 3/8 npt x 3/8 bsp make : orione holmburyuk with dust cap. note : the supplier has to demonstrate successful working of the hydraulic jack & pump after fitment/servicing....

Directorate Of Technical Education - Tamil Nadu

30686977 supply of lab items supply of lab items , supply of material testing lab i equipments , compression testing machine: ( electrically operated – 1000 kn. with single dial gauge ) the machine embodies a hydraulic system designed to meet the requirements of indian standards specification 516 1959 for compression tests on cement mortar cubes up to 7.06 cms. and concrete cubes of 15 cm. loading unit: the hydraulic jack of 1000 kn capacity is fixed to the base. the upper platen has got a self aligning action and is attached to a screw which passes through the cross head plate, and can be raised or lowered for initial clearance adjustment. the ower platen rests on the jack ram and is positioned with the help of a centring pin. loading is accomplished by upward movement of lower platen. a spacer with a centering locating pin is provided to test small specimens. the lower and upper platens of the machine are hardened ground and polished. guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack. pumping unit: the motorized pumping unit which is housed in an elegant console is of double plunger type and is driven by three phase 440 volts 50 cycles electric motor. the pumping unit is a separate unit connected to the jack by means of a steel connecting tube. a junction box is suitably fixed to connect the motor to the mains through a push button starter. the pumping unit is fitted with a 20cm dia, dial hydraulic pressure gauge with 200 division i.e. 0 1000 kn x 5 kn. a max red pointer is provided to facilitate taking readings after failure of the specimen. the machine is fitted with hand wheel control which enables the rate of application of load to vary. the machine is equipped with facility for hand.pumping in case of power faliure. the electric pumping unit is fixed with a micro switch to switch off the motor automatically as the load on the machine approaches the rated capacity. relays are incorporated in the pumping unit so that in case of breakdown of power supply, the motor will stop and would not re start unless the starting switch is operated. complete with our own calibration certificate for pressure gauge with national traceability. technical speci?cation:type of pumping : electrical loading range : 1000 kn least count : 5 kn ram dia : 165 mm ram travel in mm : 50 mm platen dia : 200 mm horizontal clearance : 250 mm vertical daylight in mm : 300 mm overload protection : yes sort circuit protection : yes motor: induction motor 1 hp 220 volts => limited...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

30640894 portable hydraulic jack portable hydraulic jack , portable hydraulic jack , portable hydraulic jacktonnage:50tstroke:18mmeffective area:78.5cm 2 inner diameter:100mm outside diameter:155*130mm body height:77mm hose length:3meter matching pump suitable pump technical data high pressure :700kg / cm 2 low pressure : 20kg / cm 2 oil storage capacity:900cc high pressure flow:2.3cc low pressure flow:13cc net weight:9.5 kg...

Southern Railway - Tamil Nadu

30611999 supply of hydraulic jack double acting cylinderhydraulic jack double acting cylinder,hydraulic jack double acting cylinder of capacity 3 ton with the following specification. 1) cylinder height: 480mm and overall height (with extended piston) is 550mm. 2) cylinder outer diameter: 185mm. 3) piston diameter : 75mm. 4) piston head dia; as per the requirement. 5) stroke length: 300mm. 6) the piston extended end outside the cylinder should be 70mm in length and diameter 75mm up to 20mm length & diameter 50mm for the remaining 50mm. 7) piston top centre should have a 16mm tapped hole. => limited...

Directorate Of Technical Education - Tamil Nadu

30569555 supply of lab items supply of lab items , supply of material testing lab i equipments , compression testing machine: (electrically operated – 1000 kn. with single dial gauge) the machine embodies a hydraulic system designed to meet the requirements of indian standards specification 516 1959 for compression tests on cement mortar cubes up to 7.06 cms. and concrete cubes of 15 cm. loading unit: the hydraulic jack of 1000 kn capacity is fixed to the base. the upper platen has got a self aligning action and is attached to a screw which passes through the cross head plate, and can be raised or lowered for initial clearance adjustment. the ower platen rests on the jack ram and is positioned with the help of a centring pin. loading is accomplished by upward movement of lower platen. a spacer with a centering locating pin is provided to test small specimens. the lower and upper platens of the machine are hardened ground and polished. guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack. pumping unit: the motorized pumping unit which is housed in an elegant console is of double plunger type and is driven by three phase 440 volts 50 cycles electric motor. the pumping unit is a separate unit connected to the jack by means of a steel connecting tube. a junction box is suitably fixed to connect the motor to the mains through a push button starter. the pumping unit is fitted with a 20cm dia, dial hydraulic pressure gauge with 200 division i.e. 0 1000 kn x 5 kn. a max red pointer is provided to facilitate taking readings after failure of the specimen. the machine is fitted with hand wheel control which enables the rate of application of load to vary. the machine is equipped with facility for hand.pumping in case of power faliure. the electric pumping unit is fixed with a micro switch to switch off the motor automatically as the load on the machine approaches the rated capacity. relays are incorporated in the pumping unit so that in case of breakdown of power supply, the motor will stop and would not re start unless the starting switch is operated. complete with our own calibration certificate for pressure gauge with national traceability. technical speci?cation:type of pumping : electrical loading range : 1000 kn least count : 5 kn ram dia : 165 mm ram travel in mm : 50 mm platen dia : 200 mm horizontal clearance : 250 mm vertical daylight in mm : 300 mm overload protection : yes sort circuit protection : yes motor: induction motor 1 hp 220 volts => limited...

Bharat Heavy Electricals Limited - Tamil Nadu

30543692 vis for booster fan foundation open tender enquiry for vis for booster fan foundation for 1x800 mw tangedco north chennai iii fgd project , supplying vibration isolation system (vis) consisting of steel helical spring units and viscous dampers with required load carrying capacities for atleast 90% isolation of dynamic loads including providing adhesive pads, templates, painting, packing, transportation, necessary manuals etc. all complete as per specification and drawing for booster fan foundations. , supplying associated auxiliaries for installation and commissioning of vis for foundations specified in st. no. 1 including frame for pre stressing, hydraulic jack system, high pressure tubes, manifold, lifting hook, packing plates, supporting stool, steel shims etc. all complete as per specification, drawing and as directed by the engineer in charge. , performing civil design engineering of rcc deck supported on vis including selection of vis, submission of documents and drawings etc. all complete as per specification and as directed by engineer in charge for booster fan foundation. , supervision by an experienced person during installation and commissioning of vis as per the specification and as directed by engineer in charge comprising the following: , temperature rise test with dissolved gas analysis test before & after , lightning impulse on hv & lv & neutral (where neutral is resistance grounded) full wave & chopped wave...

Bharat Heavy Electricals Limited - Tamil Nadu

30442394 vis for booster fan foundation open tender enquiry for vis for booster fan foundation for 1x800 mw tangedco north chennai iii fgd project , supplying vibration isolation system (vis) consisting of steel helical spring units and viscous dampers with required load carrying capacities for atleast 90% isolation of dynamic loads including providing adhesive pads, templates, painting, packing, transportation, necessary manuals etc. all complete as per specification and drawing for booster fan foundations. , supplying associated auxiliaries for installation and commissioning of vis for foundations specified in st. no. 1 including frame for pre stressing, hydraulic jack system, high pressure tubes, manifold, lifting hook, packing plates, supporting stool, steel shims etc. all complete as per specification, drawing and as directed by the engineer in charge. , performing civil design engineering of rcc deck supported on vis including selection of vis, submission of documents and drawings etc. all complete as per specification and as directed by engineer in charge for booster fan foundation. , supervision by an experienced person during installation and commissioning of vis as per the specification and as directed by engineer in charge comprising the following: , temperature rise test with dissolved gas analysis test before & after , lightning impulse on hv & lv & neutral (where neutral is resistance grounded) full wave & chopped wave...

Ministry Of Coal - Tamil Nadu

30435552 bids are invited for hydraulic jack low height 20t closed height 100mm(max) stroke 4mm(min) (q3) , single pump, double cylinder, spring return hyd jack of 5 ton capacity (q3) ,hydraulic jack of 10 ton (min) capacity, st. length50 55mm. (q3) total quantity : 5...

Ministry Of Coal - Tamil Nadu

30412887 bids are invited for hydraulic jack 50t, stroke 55 65mm, two speed hand pump000 psi qty: 5 set (q3) , hydraulic jack0t, stroke 50 60mm, two speed hand pump10000 psi. qty:5 set (q3) total quantity : 10...

Bharat Heavy Electricals Limited - Tamil Nadu

30264662 vis for booster fan foundation open tender enquiry for vis for booster fan foundation for 1x800 mw tangedco north chennai iii fgd project , supplying vibration isolation system (vis) consisting of steel helical spring units and viscous dampers with required load carrying capacities for atleast 90% isolation of dynamic loads including providing adhesive pads, templates, painting, packing, transportation, necessary manuals etc. all complete as per specification and drawing for booster fan foundations. , supplying associated auxiliaries for installation and commissioning of vis for foundations specified in st. no. 1 including frame for pre stressing, hydraulic jack system, high pressure tubes, manifold, lifting hook, packing plates, supporting stool, steel shims etc. all complete as per specification, drawing and as directed by the engineer in charge. , performing civil design engineering of rcc deck supported on vis including selection of vis, submission of documents and drawings etc. all complete as per specification and as directed by engineer in charge for booster fan foundation. , supervision by an experienced person during installation and commissioning of vis as per the specification and as directed by engineer in charge comprising the following: , temperature rise test with dissolved gas analysis test before & after , lightning impulse on hv & lv & neutral (where neutral is resistance grounded) full wave & chopped wave...

Indian Air Force - Tamil Nadu

30199365 bids are invited for jungle jim hydraulic jack (q3) , belt for brush cutter holder (q3) , jungle jim timing rod (q3) , birdscaring ribbon (q3) total quantity : 73...

Ministry Of Power - Tamil Nadu

30178606 bids are invited for spring compression jack (q3) , hydraulic gang jack: 4x100 t= 400 t (q3) , hydraulic gang jack: 4x150 t= 600 t (q3) , hydraulic puller cap 12 t (q3) , hydraulic puller cap 30 t (q3) , multipurpose hydraulic masterpuller set capacity 50 ton (q3) , hydraulic jack pumpset of 100 ton capacity (q3) , hydraulic jack pumpset of 50 ton capacity (q3) total quantity : 13...

Chief Construction Engineer - Tamil Nadu

30121547 procurement of equipment for hrs phase i vacuum viscometer bath , vacuum viscometer bath cannon manning or equivalent capillary viscometers made of borosilicate glass, calibrated with constant certificate for absolute viscosity of bituminous materials and capable of conducting tests as per is 1206 ( part ii ) 1978 and astm d2171m complete with factory calibration certificate. standard accessories: • differential mercury manometer made of borosilicate glass, graduated from 40 0 40cmsor 0 80cms with lc of 0.5mm, duly guarded with unbreakable perspex cover1 no. • high vacuum pipelines, one meter length with silicon viscometer2 nos • high performance kinematic viscometer bath: designed for 24x7 duty cycle andis used to maintain the correct constant temperature for estimating viscosity from below ambient to 160°c 1 no • silicone thermal fluid suitable for temperature up to 250°c20 litres • cannon manning or equivalent tube size: 12 viscosity range ( poises ) 360 80002nos • cannon fenske or equivalent reverse flow capillary viscometers tube sizes: 6 viscosity range ( cst ) 60 1000 1 no • thermometer: mercury in glass, ip5cfor kinematic viscosity1 no including warranty for the period of 12 months from the date of supply or installation whichever is later. , universal digital penetrometer , universal digital penetrometer capable of conducting test as per astm d5, and is 1203:1978 with the following features: • opto electronically depth detection & measurement through opto electronic sensor • display resolution of penetration depths in tenths of units ( 0.01mm ) • magnifying lens for adjusting needle tip / cone tip exactly on the sample surface. to be supplied complete with the following items for bitumen penetration, •weight of 50 grams 1 no. • penetration cup of 55mm diameter x 35mm height 1 no. • transfer dish 1 no. • penetrometer needle 1 no. • needle holder 47.5g ± 0.05g 1 no. • thermometer astm 17c ( +19 to 27 °c ) 1 no. including warranty period of 12 months from the date of supply or installation whichever is later. , digital ductility testing apparatus , digital ductility testing apparatus capable of conducting the testsas per astm d113 with the following features: •cooling arrangement • equipped with testing three specimens simultaneously • electric pump circulator and heater. • the temperature is controlled by digital temperature controller with two rates of travel are to be provided i.e. 5cm / min and 1cm / min. • suitable for operation on 220v, 50 hz, single phase, ac supply. including warranty period of 12 months from the date of supply or installation whichever is later , rolling thin film oven , rolling thin film oven capable of conducting the test as per astm d2872. with following features: • low thermal mass rtd.;• over temperature safety cutout ;• double walled temperature cabinet • 16 gauge welded steel exterior;• 18 gauge corrosion resistant stainless steel interior • insulation with 89mm high density fiberglass ;• programmable microprocessor ul listed controller • 4 digit red led temperature display;• 4 digit green led for temperature set points • including thermal protection which prevents oven in event of control failure;• temperature range: ambient to 200deg c • double exhaust vents;• needle valve for air flow adjustments;• air pressure gauge range ( 0 to 100 psi ) • heat exchanger 5 / 16 inch dia. copper tube;• electrical supply : 230v ac supply, 50hz single phase • dimension : 1016x660x915 mm;• estimated weight : 100 kg ;including warranty period of 12 months from the date of supply or installation whichever is later. , digital marshall stability apparatus , digital marshall stability apparatus of 100kn single speed for4” / 6” dia. samplecapable ofconducting the test as per ms 2 and is 17127:2019 including calibration certificate with the following features : •load frame, • holder pin, • power cable, • load transfer bar, • steel ball, • electronic kit indicator containing . load cell with adapter and cable . displacement sensor with cable • 4” / 6” dia. sample mould assembly with . rammer . extractor . round plate . dummy plate . handle pipe . breaking head . pedestal ( 4” / 6” sample ) including warranty period of 12 months from the date of supply or installation whichever is later. , california bearing ratio testing machine , california bearing ratio testing machine capable of conducting test as per is 2720 part xvi with the following features: • compact, bench top design, rapid platen adjustment complete with stabilizing bar options for mechanical or electronic measurement • suitable for operation on 220v, 50hz, single phase, ac supply;• digital indicator ;• mode of display: micro controller multiline, alpha numeric lcd display for all simultaneous channel ( no need for channel selection ) ;• load cell, capacity: 50kn compression type;• three speed 1.5 mm / min, 1.25 mm / min & 2.5 mm / min, maximum: 110% of the rated capacity • sensing: strain gauges in full bridge configuration;• displacement transducer range: 0 20 mm with 3m long cable • sensing element: lvdt ;the equipment shall be supplied with ;•laptop computer ( minimum intel i5 processor, 8gb ram ) loaded with licensed microsoft windows 10 os ( lifetime free update ) – 64 bit;•ms office bundle software valid for 5 years and other suitable software for conducting all the above tests with recording and analyzing.;including warranty for period of 12 months from the date of supply or installation whichever is later. , automatic california bearing ratio test apparatus , automatic california bearing ratio test apparatus capable of conducting test as per is 2720 part xvi. with the following features: • motorized electronic with data acquisition system;• geotechnical software for testing, analyzing and reporting; • the software should allow selection of british / indian standards for analysis.; • tests are to be performed in si, imperial or metric units.; • test information is to be presented on menu driven screen.;• each package guides through the test procedures is to be in very user friendly way.;• a database setup to store and manage completed analysis records with ms access as default system.; • the software has to read the data format for analysis from star daq ;• an option to enter the data manually and save; • with extensive search functions based on date of analysis, analysis done by different user accounts or search based on duration etc, for easy retrieval of old data.; • the default reports shall be automatically generated in crystal reports and to be printed directly.;• the reports shall be exported to word, excel or pdf formats.; • customizable report header / footer; • the inbuilt utilities include master unit conversation calculator, besides the normal and scientific system calculators.; • database backup and restore facilities ;• complete user activity logging ; special features and graphs for cbr analysis software • manual data entry facility ;•to find out cbr value in % at 2.5 mm and 5mm penetration.;• graph for load vs penetration ( top side, bottom side and both ) .;• graph correction facility ; • graph expand facility.; with software for the following tests •unconsolidated undrained triaxial test;•consolidated undrained triaxial test;• consolidated drained test; •direct / residual shear test;•cbr test;•one dimensional consolidation test;including warranty period of 12 months from the date of supply or installation whichever is later. , automatic soil compactor , automatic soil compactor capable of conducting test as per is 2720 part viii complete with the following features •motor driven mechanical compactor for soil compaction in 100 mm or 150 mm dia moulds. •two rammers with different stroke length that should travel across the mould and the table rotates the mould in equal steps on a stable base. •the number of blows per layer can be set at the beginning of the test. • rammer circular faced 50mm dia. adjustable to 2.6kg or 4.9kg weight •drop adjustable to 310mm or 450mm. •digital display for counting the number of blows. •the equipment should be suitable for operation on 220 v, 50 hz, single phase, ac supply including warranty period of 12 months from the date of supply or installation whichever is later. , automatic vicat’s apparatus , automatic vicat’s apparatus for setting time test on cement / mortar / gypsum conforming to en 196 3, 13279 2, 480 2, is 4031 part 4& 5, astm c191, c187 complete with the following accessories: • initial setting time needle 1.13 mm dia, 1 mm diameter needle mould;•needle for final setting test; • cylindrical probe for consistency test;• accessory for needle continuous cleaning and in water testing; • icon driven capacitive sensing touch screen graphic display with 800 x 480 pixels, 16 m colors ; • graphic printer; • usb port for data storage, export to pc and firmware upgrade and ethernet port for pc / network communication and network mode with up to 32 independent units; • 16 gb internal permanent memory on sd card;•to be supplied complete with necessary software for remote pc control including lan cable ; to be supplied complete with the following features ;• fully automatic test cycle; • easy re call of test settings from test profiles database ;• easy programming of customized test including: test start delay, penetration points positions, manual or automatic penetration rate, free or driven mode, holding intervals, automatic end test detection.; •automatic measurement of initial and final setting time;• easy calibration menu including warranty period of 12 months from the date of supply or installation whichever is later. , digital flexural testing machine , digital flexural testing machine ( 100kn ) conforming to is 516, bs: 1881 and astm c78 with the following accessories: •suitable frame ; •double action hydraulic pump •self aligning roller assembly ; •hydraulic jack provided with retraction spring for testing beams of 100x 100x500mm and 150x 150 x 700mm;•suitable for operation on 220v 50hz, single phase, ac supply including warranty period of 12 months from the date of supply or installation whichever is later. , automatic blaine’s apparatus , automatic blaine’s apparatus capable of conducting tests conforming to astm c204, en 196 6, is:1727, 4031, 4825 with the following features: •automatic control of the movement of fluid until the upper mark.;•automatic sensing of the upper & lower marks ensuring error free repeatable measurement of the time taken for the liquid column to fall.;•automatic measurement of temperature during the test using a probe including automatic correction of formula for calculation of the blaine value per is: 5516 with variation in temperature.;• facility to operate in either standalone mode or through a computer controlled system complete with software login facility.;•report generation based on date / time. user type & type of cement in excel or equivalent format. including warranty period of 12 months from the date of supply or installation whichever is later. , rebar locator profometer 650ai , rebar locator profometer 650ai capable of conducting corrosion measurement conforming to astm c 876 consisting of profometer with the following features: •touchscreen, •universal probe with probe cart, •probe cable 1.5 m ( 5 ft ) , •power supply, ;•usb cable, dvd with software; •documentation, •activation key; •carrying strap and carrying case ; •upgrade kit to profometer corrosion consisting of interface box, ;•cable coil of length 25 m ( 82 ft ) with clamp, ;•dvd with software, •documentation and carrying case;•profometer corrosion rod electrode, with spare parts, cable including spade terminal adapter and copper sulphate ( 250g ) ;•profometer corrosion one wheel electrode, with telescopic handle, encoder, cables, spare parts, tool kit, copper sulphate ( 250 g ) , citric acid ( 250 g ) etc complete ; including warranty period of 12 months from the date of supply or installation whichever is later. , multipurpose universal testing machine , multipurpose universal testing machine 2000kn servo controlled machine capable of conducting tests conforming to is 1828 part 1:2005 with the following features: •hydraulic power system, • microprocessor control unit, ;• user interface with large graphic display with keyboard; • data acquisition testing system and related legal and licensed version of interactive software. with the following accessories;• 2000kn loading unit; • servo pump system ; • clamping jaws for round specimen 08 70mm; • clamping jaws for flat specimen 0 40mm; • clamping jaws for ht strand wires 12.7 and 15.2mm;• bend test 180 degree attachment; • bend re bend test attachment • electronic extensometer with 25mm & 50mm gauge lengths & 600 mm forht strand wires; • shear test attachment 6, 8, 12, 16, 20mm;• shear test attachment 25, 30, 35, &40mm ; • flexure test attachment • wire rope test attachment 0.12 13.2 mm;the servo pump with the following features • standalone close loop automatic control console to perform tests under control of: load / stress and displacement by suitable transducers.• the rate of strain shall be adjustable between 0.00025 / s and 0.0025 / s and rate of stress 1 to 50 n / mm2 per second.including warranty period of 12 months from the date of supply or installation , digital compression testing machine , digital compression testing machine 2000 kn plates and accessories conforming to is 516 & is 14858:2000. with the following features: •digital indicator having 4 digits display calibrated in kilo newton ( kn ) and preset to maximum load capacity fitted with micro switches.;•electrically operated pumping units provided with control knob to adjust the pace rate and provided with a pace indicator to indicate pace rate on a bar graph.;•the pace shall be controlled manually while the test is in progress including warranty period of 12 months from the date of supply or installation whichever is later. , universal testing machine , universal testing machine ( 1000kn ) capable of conducting tests conforming to is 1828 part 1 2005 with the following features; • hydraulic jaw set with a resolution of 0.01kn ;• max clearance for tensile test shall be 50 700 mm; • max clearance for compression test shall be 0 700 mm ;• clearance between columns 650mm, • ram stroke: 250mm ;• piston speed at no load should be 0 50mm / min• fully enclosed and protected load measuring system. load frame with rigid construction.;• motor driven threaded columns for up / down movement of lower crosshead for quick change over of specimen, grips and attachment.• power pack should generate a maximum pressure of 200 kgf / cm².;• system should have high precision, sealed and accurate pressure transducer mounted in thehydraulic pressure line of the loading unit;• system should have ergonomically designed micro process unit selection for load, displacement.;• results should include load vs displacement curve, maximum displacement, uts, %elongation, youngs modulus and proof stress; system should include the following accessories:;• clamping jaws for round specimens 8 25mm, 25 45mm; • clamping jaws for flat specimens thickness: 0 40mm; • flat specimen width: 70mm for tension test, ; pair of compression plates;• electronic extensometer strain gauge type with gauge length 25mm and 50 mm; • brinell test attachment, • bend / rebend test attachment , • flexural test attachment. system shall be supplied with following features:• software should have the features for data analysis like mean deviation, frequency distribution, skew diagram, histogram and graph.;• system should be calibrated in accordance with bs:1610 and is standards and it should comply with grade a of bs 1610:1964 and grade 1 of is: 1828 1991.;• power supply: 440v, 50hz, three phase, ac supply. • computer and printer should be supplied with the system having minimum specifications as follows; • i5 or better, 4 gb ram, ;•processor, 256mb , 250gb hd drive, cd rom drive, ;•mouse or pointing device and keyboard supported by windows 10 pro 64 bit and ms office bundle.;• monitor that supports 1024x768 resolution and 32 bit color, 2 usb serial port adapter per machine;• windows compatible sound card and speakers ( for audio playback ) • additional usb ports for measuring devices, barcode scanners, printer;• one integrated serial port ( not usb ) where possible, lan card for connecting with electronic panel .;including warranty period of 12 months from the date of supply or installation whichever is later. , autocad software , autocad softwarewith the following features: •specialized toolsets ad commercial new single user eld with annual subscription. , desktop systems with licensed latest windows os 64bit , desktop systems with licensed latest windows os 64bit with the following futures: • genuine window 10 pro 64 bit ;• intel core i5;• 8 gb ram;• 1 tb harddisk ;•2gb graphics memory ; •19.5 inches monitor;including warranty period 36 monthsfrom the date of supply or installation whichever is later. , multi functional plotter , multifunctional wide format colour plotter, • size a0 to a4 with licensedsoftware ( hp / canon or equivalent ) ; including warranty period 60 months from the date of supply or installation whichever is later. , matlab software , matlab software withthe following features: • toolbox for image processing; • image acquisition;• curve fitting ; • optimization; statistics stics and machine learning • deep learning, computer vision toolbox. , vissim software , vissim software perpetual corridor pos 1a software ( for standalone license: 1 user ) with 20 signal controllers, with the following features : • unlimited network and modules for 3d package, ;• signals, synchro import, ; • public transport, ; • com ( event based scripts etc ) , • managed lanes • with one year maintenance of software• viswalk size 1: pos 2a software for maximum 10, 000 pedestrians simultaneously in system. , z 250 reference profiler , z 250 reference profiler towards the procurement and supply of z250 reference profiler with first annual maintenance subscription ( ams ) •including packaging ; •shipping & insurance; •local custom clearances ; •local agent charges. ; including warranty period of 12 monthsfrom the date of supply or installation whichever is later. , video camera unit , drone camera dji camera or equivalent with the following accessories: • aerial video recording & photography, ;• sensor size of 1 / 2.3 inches, ;• cmos, optical zoom of 6x, • max speed 50 to 55 mph with flight time of 27mins, ;• 10 million pixels, • remote distance of 5 to 7km control range with fpv operation, ;• 2control channels, • app controller connectivity, ;• 4k hd video recording, • digital video zoom, ;• d log m and hlg hdr for high dynamic range recording and 10 bit support. • footage that is suitable for high end grading and editing applications; including warranty period of 12 months from the date of supply or installation whichever is later. , video camera of sony pxw z series or equivalent 4k xdcam with super 35 camcorder kit with zoom lens or equivalent, with the following accessories: • e mount locking sys mechanical adapter, ;• variable electronic neutral density nd 2 to 7 stops filter, ;• built in mic viewfinder and short gun mic holder mount with latest rolling shutter technology, ;• wi fi adaptor, • controllable zoom focus iris & white balance as well as recording functions, control with apple ipad or android mobile device., internal recording in both dci 4k & uhd 4k upto 59.94 frames / sec, ;• camera tripod, ;• carry case including warranty period of 12 monthsfrom the date of supply or installation whichever is later. , still camera , still camera nikon d6 dslr cameraseries or equivalent with selectable lenses with the following accessories: • 20 mp fx cmos sensor ;• 14fps shooting ( video mode ) ;• 4k ultra hd video recording at 30fps;• built in wi fi • bluetooth and gps;• touch screen lcd monitor;• expeed 6 image processor or equivalent • 64gb memory card 1no, wireless ttl flash;• shoulder bag;• sony 64gb g series xqd memory card or equivalent • nikon af s zoom lens200 500mm f / 5.6ed or equivalent;• normal 50mm;• bolt vs 570n wireless ttl flash or equivalent • free wave wireless remote ;including warranty period of 12 months from the date of supply or installation whichever is later. , video editing unit , video editing unit consisting intel core i7 10th gen processor ( windows platform ) with asus b250m plus motherboard or equivalent with the following accessories: • 64gb ddr4 ram ;• 350gb ssd wd hdd ;• 2tb sata wd hard disk ( 2nos ) • w5000 g force8gb / asus game engine or equivalent ;• cooler master cabinet or equivalent ( industrial cabinet ) • cooler master 750w smps or equivalent, digital intermediate panel board;•keyboard and mouse, editing console table • blue ray writer;• lg 22 inch led monitor 2 nos ;• television 32inchs preview monitor ;• monitor speaker 2 nos • hdmi splitter with cable ( according to the length ) ;• speaker stand 2nos, interconnecting cables ( signal / pwr / bband / ethernet / hdmi , sound proof & acoustic ( sq ft rate 1200 / sqft ) ;• lightings / emergency light.;• fcp / premier pro ( any one ) ;• photo shop & after effect ;• deviancy / assemblator ( scratch ) ;• software required;• windows 10 / 64 bit pro and ms office bundle. ;including warranty period of 12 months from the date of supply or installation whichever is later. , sound recording editing unit , sound recording editing unit consisting intel core i7 10th gen processor ( windows platform ) with asus b250m plus motherboard or equivalent with the following accessories: • 64gb ddr4 ram;• 350gb ssd wd hdd;• 2tb sata wd hard disk 2 nos;• w5000 g force8gb / asus game engine or equivalent;•cooler master cabinetor equivalent ( industrial cabinet ) , ;• cooler master 750w smps or equivalent • keyboard and mouse ;• blueray writer;• lg 22 inch led monitor or equivalent 2 nos ;• television 32inchs preview monitor, ;• mackie ssl soundscape 32 daw hardware or equivalent;•digital portable mixing console o3d yamaha or tascam or equivalent ;• audio interface ( audio card ) ;• akg 1000c condenser microphone or equivalent 2 nos • akg headphone or equivalent 3 nos ;• studio monitor speaker 2 nos ;• hdmi splitter with cable ( according to the length ) , ;• mic stand 2 nos ;• speaker stand 2 nos ;• working table ( mixer and console table with rack ) • console and studio chairs, pop filter ( blow cutter ) ;• interconnecting cables ( signal / pwr / ethernet / hdmi • sound proof & acoustic for console and vox room ( @ sq ft rate 1200 / sqft ) ; • vox room 200 sqft • console cum engineer room 250 sqft ;• air condition plant4ton ( 2x2 ) , lightings / emergency light / sign boards softwares required are:• protools ver.10 or 12 & sscape daw software ( digital audio workstation ) or equivalent ;• coustica or equivalentnoise cleaning software • window 10 pro 64bit and ms office bundle;includingwarranty period of 12 months for from the date of supply or installation whichever is later. , multifunctional colour copier machine , all in one color printer, digital color mfd ( print / copy / color scan / stores / scan to e mail and folder ) with the following features: • 30 cpm / ppm copying / printing speed;• up to a3 size ;• digitalinbuilt network printer;• copier color ;• duplex printing & copying ;• dadf ( duplex automatic document feeder;• 3 gb ram;• 250gbhard disk ;• 2auto trays ( 550+550 ) sheetscapacity;• 100 sheets bypass;• 200x1200 dpi resolution;• 1.5kw or less power consumption;• 25% 400% zoom ration • rotate collate;•toner yield – black – 36000 copies;•color ( c / m / y ) – 19000 copies each;•drum yield – black –84000 copies •color ( c / m / y ) 66000 copies each;•machine life 10 lakh copies, ;•value addition: pearl make or equivalent movable trolley with shelf and 2kva stabilizer;• brand canon model: ir adv dx 3730or equivalent; includingwarranty period of 12 months for from the date of supply or installation whichever is later. , all in one wireless colour printer ofink tanktype color printer with all in one ( print, scan, copy ) functionality with iso standards with the following features: • wi fi connectivity; • usb, canon selphy app or equivalent. ;• compatible withwindows 10, windows 8.1, windows 7 sp1. • power requirements of 200 to 240 v;• 50 / 60 hz;• 1.2 inch lcd diplay on printer ( mono ) • 8.8 ipm ( black ) ;• 5 ipm ( colour ) ;• as per iso standards. page size supported 4.0x6.0 till a4 / letter / legal / a5 / b5with • print resolution of4800 x 1200 dpi, ;• compatible ink bottle gi 790 ( bk ) , gi 790 ( cyan, magenta, yellow ) , ;• page yield of 6000 pgs ( bk ) , 7000 pgs ( color ) – with 1 set of all 4 ink bottles inside the box ( as per iso standards ) ;• brand canon pixma g3010 or equivalent ; all in one wireless ink tank colour printer or equivalent; including warranty period of 12 months the date of supply or installation whichever is later. , laser printerwithall in one ( print, scan, copy ) functionality with the following features: • printer output mono ( black ) .;• usb 2.0 connectivity.;• wi fi, canon print business, canon print service, google cloud print, apple airprint, mopria or equivalent.;• 6.9cm bw lcd display panel.;• compatible with 32 / 64bit windows 10, 8.1, 8, 7, vista, ;windows server 2012 r2 ( 64bit ) , ;windows server 2012 ( 64bit ) , ;windows server 2008 r2 ( 64bit ) , ;windows server 2008, windows server 2003 r2, ;windows server 2003, ;• mac os x ( *4 ) 10.6.8~, linux ( *3 ) or equivalent, up to 27ppm ( a4 ) , 6.0s • print language ufr ii lt, pcl 6;• device memory 512mb;• duplex;• page size supported a4, b5, a5, ;• legal, letter, statement, executive, ;• government letter, government legal, ;• foolscap, indian legal ;• custom ( minimum 76.2 x 210mm to maximum 216 x 356mm ) ;• print resolution 600 x 600dpi;• cartridge 337; page yield 2400 pages. ;• as per iso standards, ( canon mf244dw digital multifunction laser printer, black, standard or equivalent ) ;including minimum warranty period of 12 months fromthe date of supply or installation whichever is later. , garden maintenance machine , brush cutter with the following features; • powered by42.7 cc with 2 stroke air cooled engine, ;• fuel tank capacity of 0.9 ltrs., ;• dry weight 8.0 kgs, ;• cutting tool steel blade, ;• nylon head & 15 metre nylon rope ;including warranty period of 12 monthsfrom the date of supply or installation whichever is later. , lawn mower with the following features: •powered by electric motor, ;•3 phase / 440v, ;•5 hp / 2880 rpm, ;•cutting width of 45 cm, ;•cutting height of 10 100 mm ( 6 stages ) , ;•straight blade•steel cutting deck , ;•cable length 4;including warranty period of 12 monthsfromthe date of supply or installation whichever is later. , vaccum cleaner , vacuum cleaner with the following features: • 230 240 / 50hz voltage, ;• 1350 w power, ;• ametek or equivalent motor, • 54lps airflow with suction power of 22 kpa, ;• tank volume of 35 litres, ;• dimensions cm ( lxwxh ) 36x36x76, • weight 9 kg ;• brand : eureka forbes model : pro vac wd 35 or equivalent; including warranty period of 12 monthsfromthe date of supply or installation whichever is later. , laptop and desktop computers , laptop with the following specifications; • intel core i7 1165g7;• 8gb ddr4;• 512gb ssd;• 15.6” ( 1920x1080 ) ;• 2 gb dedicated graphics / hd • webcam backlit keyboard;• finger print reader;• wifi 6+bt 5.0;•maximum weight of 1.8kgms office licensed software. • win 10 pro – 64 bit ms office bundle ;• brand: dell or equivalent; including warranty period of 36 monthsfromthe date of supply or installation whichever is later. , desktop systems with licensed latest windows os 64bit with the following futures: • genuine window 10 pro 64 bit ;• intel core i5; • 8 gb ram; • 1 tb harddisk ;• 2gb graphics memory • 19.5 inches monitorincluding warranty period 36 monthsfrom the date of supply or installation whichever is later. , ms office 2019 standard version , calculation of subtotal, gst and total amount carried out by system automatically , basic cost of value put to tender as per estimate , add gst at 18% , total value put to tender , negotiated percentage , final negotiated value , add gst at 18% of final negotiated value , total value of contract including 18% of gst , basic cost of value put to tender as per estimate , quoted rate in figures ( total value of contract including 18% of gst ) ...

Ministry Of Coal - Tamil Nadu

30063776 bids are invited for hydraulic jack oil seal: 315 x 355 x 33.3mm for wagner press ( q3 ) , vako brand synthetic rubber wiperto size 315x335x10.2 / 18mm ( q3 ) total quantity : 32...

Southern Railway - Tamil Nadu

29443136 supply of hydraulic jack 20 ton capacityhydraulic jack 20 ton capacity,hydraulic jack 20 ton capacity specification as per attached annexure...

National Project Implementation Unit - Tamil Nadu

29435258 equipment for static and dynamic analysis of welded slewing ring bearing for high thermal application equipment for static and dynamic analysis of welded slewing ring bearing for high thermal application project , linear variable differential transformer (lvdt) & strain gauge , linear variable differential transformer (lvdt) (as specified in the gtecppp11202122.xls against sl. no. 1.1) , strain gauge (as specified in the gtecppp11202122.xls against sl. no. 1.2) , hydraulic jack with load cell , hydraulic jack (as specified in the gtecppp11202122.xls against sl. no. 2.1) , load cell (as specified in the gtecppp11202122.xls against sl. no. 2.2) , electrical coil heater , electrical coil heater (as specified in the gtecppp11202122.xls against sl. no. 3) , ac induction motor , ac induction motor 10 hp (as specified in the gtecppp11202122.xls against sl. no. 4) , ac induction motor 5 hp (as specified in the gtecppp11202122.xls against sl. no. 4) , pid controller , pid controller (as specified in the gtecppp11202122.xls against sl. no. 5)...

Ministry Of Defence - Tamil Nadu

29350993 bids are invited for 30 t single acting hydraulic jack, stroke: 200 250 mm, with: hydraulic two speed steel hand pump total quantity : 1...

Ministry Of Home Affairs - Tamil Nadu

29249148 bids are invited for hydraulic jack , metal primer red oxide , paints white , paints itbp khaki , paints black , paintsthinner total quantity : 79...

Department Of Heavy Industry - Tamil Nadu

29191027 bids are invited for hydraulic jack for scr cartsauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes ( a maximum of300 times ) total quantity : 6...

Ministry Of Steel - Tamil Nadu

29104671 bids are invited for boq total quantity : 1 1 10 t hydraulic jack with hand pump 2 20 t hydraulic jack with hand pump 3 50 t hydraulic jack with hand pump...

National Project Implementation Unit - Tamil Nadu

28809618 equipment for static and dynamic analysis of welded slewing ring bearing for high thermal application project equipment for static and dynamic analysis of welded slewing ring bearing for high thermal application project , linear variable differential transformer ( lvdt ) & strain gauge , linear variable differential transformer ( lvdt ) ( as specified in the gtecppp11202122.xls against sl. no. 1.1 ) , strain gauge ( as specified in the gtecppp11202122.xls against sl. no. 1.2 ) , hydraulic jack with load cell , hydraulic jack ( as specified in the gtecppp11202122.xls against sl. no. 2.1 ) , load cell ( as specified in the gtecppp11202122.xls against sl. no. 2.2 ) , electrical coil heater , electrical coil heater ( as specified in the gtecppp11202122.xls against sl. no. 3 ) , ac induction motor , ac induction motor 10 hp ( as specified in the gtecppp11202122.xls against sl. no. 4 ) , ac induction motor 5 hp ( as specified in the gtecppp11202122.xls against sl. no. 4 ) , pid controller , pid controller ( as specified in the gtecppp11202122.xls against sl. no. 5 ) ...

Ministry Of Petroleum And Natural Gas - Tamil Nadu

28655767 bids are invited for non sparking chain pulley block non spark 5mt capacity and 6m lift , aluminum ladder 12 ft self sported , mt mechanical screw jack , 10 mt hydraulic jack with handpump , 30 mt hydraulic jack with hand pump total quantity : 10...

Indian Coast Guard - Tamil Nadu

28364488 procurement of main engine cylinder head spares for icgs samudra paheredar , cap screw/allen screw , valve guide exhaust valve/ valve guide , valve rotor/b eng . , seat lock , o ring/o_ring 490 x 7 , 5 viton 75 , valve guide inlet valves/valve guide , o ring/o_ring 490 x 7 , 5 viton 75 , washer , socket head screw/allen screw , exhaust valve/valve exhaust , inlet valve/valve inlet , hydraulic jack seal kits/o ring kit hydraulic tool , cyl head gasket kit/cylinder head overhal . sett b32 , o ring/o ring , o ring/o ring , valve seat exhaust/cooled valve seat , exhaust , valve seat inlet/valve seat , air , any other charges...

Neyveli Lignite Corporation Limited - Tamil Nadu

28069513 supply of light weight hydrualic jack of capacity 100 tons, retracted cynlinder height(max):140mm, stroke length(min):50mm. jack, hydraulic jack with hand pump ( capacity: 50tons) consisting of 1. cylinder collapsed height 4 to 5 inches, stroke length 2.25 to 2.75 inches, spring return type. 2. a suitable 2 speed hand pump 3. heavy duty rubber hose of min 5 feet length. 4. suitable pressure gauge, adapter& coupler set, oil prefilled....

Neyveli Lignite Corporation Limited - Tamil Nadu

27338793 supply of 10 ton capacity single acting cylinder with spring return hydraulic jack and pump, one seal kit for the jack, hydraulic jack single acting spring return low height of capacity 10 tons, closed height:90 mm ( max ), stroke: 25 mm ( min ), working pressure 700 bar/10000 psi,hydraulic jack single acting spring return low height of capacity 20 tons, closed height:110 mm ( max ), stroke: 40 mm ( min ), working pressure 700 bar/10000 psi...

Bharat Heavy Electricals Limited - Tamil Nadu

26813650 items bhel / trichy invites applications for regn . from suppliers / manufacturers for supply of various items cast: aluminium astm a 217 c12a castings cast iron castings for windbox, feeder coal nozzles ( sg iron castings up to 850 kgs ) castings for oil field equipments: carbon, alloy and stainless steel qcnrv castings hemi spehrical dished ends ¿ grade 91 hemi spehrical dished ends ¿ alloy steel ( upto gr 22 ) die forgings for oil field equipments: carbon, alloy and stainless steel open forgings f91, f92 f92 forgings closed die forged components forged finned elbow forged flanges formed fittings: large 12 and above, forged finned elbows formed fittings: small 2 to <12 socket welded forged fittings open forgings carbon, alloy and stainless steel except sa 182 f91 inconal fittings inconel forgings for valves investment castings for connectors, windbox sa 351 gr ch 20, sa 351 ck 20 investment castings castings: malleable iron nickel based castings non ferrous castings for feeder: is 617 4223, is 617 4450, is 305 gr ab1, astm b 148 gr 9c non ferrous castings ( 0.5 to 200 kg ) open forgings for oil field equipments: carbon, alloy and stainless steel open forgings for hp bypass valves: carbon and alloy steel formed fittings p91 f92 fittings steel castings sg iron machined castings for coal nozzles, split collar for wind box: astm a 536 gr 654512 sg iron castings close die forgings: carbon, alloy and stainless steel open forgings for valves carbon steel, alloy steel and stainless steel castings for valves name plate metallic fasteners: hsfg bolts and nuts as per tdc:5:211 / 01 precsn bolts, studs, screws and nuts dip coat paint, thinner and special additive h.r. aluminium paints grade i h.r. aluminium paints grade ii conventional paints and thinners epoxy based paints and thinners epoxy finish paints and thinners special primer paints and thinners seamles p91 / p92 pipes alloy steel pipes: sa 335 p11, p12, p22 ; od 88.9 to 1016 mm, 6.02 to 135 mm thick carbon steel pipes: sa106 gr b, c; od 88.9 to 1016 mm, 6.02 to 135 mm thick pipes & tubes ( welded stainless steel erw / saw pipes : api 5l gr b, od 219.1 to 1168 mm, 4 to 14.3 mm thick erw black pipes: is 1239, nb 80 to nb 150, light, medium and heavy thick seamles p91 / p92 pipe alloy steel pipes: sa 335 p11, p12, p22 ; od 88.9 to 1016 mm, 6.02 to 135 mm thick carbon steel pipes: sa106 gr b, c; od 88.9 to 1016 mm, 6.02 to 135 mm thick gi wire: is 280, dia 0.711 mm to 1.219 mm alloy steel rounds for valves: 21crmov57, sa 193 b7, a322 gr 6150, sa 193 b16, sa 182 f22 cl3, aisi 4140, aisi 1040, : dia 22 mm to 300 mm brass sheets, 0.2 mm and 1.0 mm thick carbon steel rounds for valves: aisi 1040, sa 105, is157013ni3cr80, is1875 cl.4: dia 22 mm to 300 mm 17% gr. ss ( othron steel ) rods, astm a182 f430, dia 25 mm to 200 mm alloy steel plates to grade sa387 gr91 cl 2 alloy steel rounds to grade sa182 f91 stain l ess steel rods, dia 25 mm to 250 mm of different specs including sa 182 f304, sa 479 304, sa 182 f316, a276 410, aisi 410, a582 416, a276 420, a565 616, sa 564 630, a182 f6a cl3, 17 4 ph special stainless steel rounds: x 19 cr mo vn bn 111 6010 dia 52mm, 56 mm and 125 mm alloy steel rounds / blooms alloy steel plates: sa 387 gr 12 cl 2, gr 22, gr 91 4 mm to 120 mm thick alloy steel rounds: sa 182 f12, f22, sa193 b7, b16, astma600t4 dia 6 mm to 200 mm carbon steel plates boiler quality ( sa299 gr a ) 65 mm to 190 mm thick carbon steel plates boiler quality ( sa515 gr 70 ) 5 mm, 6 mm, 63 mm to 100 mm thick carbon steel rounds / blooms structural quality plates bsen 10025 3 / s420n, a36 75 mm to 155 mm thick structural quality plates carbon steel is 2062 e250 gr a, b / is 513 osk and dsk / is 1079 0.9 mm to 63 mm thick corsn resi. steel sheets and plates astm a 588 gr a, corten a, jis 3125 2.5 mm to 5.0 mm thick angle, channel, beams heavy section ( a 130 200 mm, b 400 600 mm and c 300 ? 400 mm ) angle, channel, beams light section ( a 40 65 mm, b 125 200 mm and c 75 ? 100 mm ) angle, channel, beams medium section ( a 75 100 mm, b 250 350 mm and c 200 ? 250 mm ) parallel flange beam / u beam / h beam 150 mm 700 mm carbon steel boiler quality rounds: sa 105 20 mm to 200 mm dia. carbon steel rounds: is 2062, is 1875 cl 4 8 mm to 100 mm dia. stainless steel sheets and plates: sa 240 tp 300, 400 series 0.6 mm to 50 mm thick stainless steel rounds: sa 479 tp 300, 400 series, sa 182f316 6mm to 100 mm dia. tmt bars dia 8 mm to 40 mm special alloy steel rods for hplp valves ifm gas ignitor, 0.25 kw heat capacity, length ignitor 900 to 1265mm, 110 v / 240 v, ac regulating duty electrical actuator ( for dampers ) transmitter ( pressure / flow / temp ) actuator: pneumatic ( open / close type ) regulating duty pneumatic actuator ( for dampers ) proximity switch bdt / tubular level gauges electrical accessories for valves fractional hp motor for soot blowers panels: plc based control system cast aluminium junction box ( non flame proof ) compensating / extension cable cable dressing materials mpgfc cpu brass cable gland and cable gland adapter gi perforated / ladder type cable tray cable tags cable lugs pvc insulated copper control cable ( frls ) pvc insulated multipair instrumentation cable ( frls ) frp junction box flame scanner head assy ( safe flame ) flame scanner cable ( thermoplastic / elastomeric / equiv alent material insulated double shielded copper instrumentation cable ) flame scanner assy ( industrial boilers ) flame scanner head assy test kit flame scanner head electronics mpgfc i / o modules / mp based gr. feder control mpgfc kbd and ps / mp based gfc key board and power supply electrical panels: ac / dc distibution ptfe insulated and outer sheathed extension cables mpgfc rack, pcb and accessories vfd controller wired modular panel local control panel weighing module wired modular panel remote control panel airfilter regulator sheet steel junction boxes starter / cntrl boxes: dc and ac local starter / mill fire flame proof boxes ( cast aluminium ) galvanized sheet junction box electrical actuator motor control centre / power control centre stainless steel junction boxes ash level switch acoustic pyrometer modular type cabinet bottom ash load cell bunker load cell bhelvision: electrical accessories cctv system for furnace flame viewing condensing pot / constant head unit gravimetric feeder control modules electronic modules for flame scanner system electronic modules for acoustic steam leak detection ( asld ) system electronic modules for electronic water level indicator ( ewli ) earthing system pressure switch for electromatic releif valve electronic water level indicators fluegas analyzers ( dilution probe ) flue gas analyzers, smoke density: opacity / particulate measurements fluegas analyzers: oxygen measurement at boiler eco. inlet fluegas analyzers: sox / nox hot extraction type flow nozzles furnace flame viewing camera system and thermographic analysis system dp gauges pressure gauges temperature gauges signal isolator ( i / p converter ) local instrument enclosure passenger and goods elevator local instrument rack mass flow meter metal temperature measurement thermocouple process thermocouples and rtds with thermowell orifice plate assy purge meter ptfe insulated multipair instrumentation cable erv controller and control station steam and water analysers online carbon in ash analyser system vibration monitoring system for motor / fan bearing xlpe insulated lt power cable ( copper and aluminium ) coal motion monitor sensor cable assembly digital tachometer feeder belt lt motors: weather proof / flame proof panels for feeder integral cabinet fibre optic cable and lens barrel assy. calibration kit for solid state feeders copper / ss tube for instrumentation application decibel scanner unit with pc and software for asld system micro switch for gravimetric feeder pressure and dp swithces critical application pressure gauges pressure gauges critical application pressure switches position transmitter for quick closing non return valves electrical control panel for soot blowers limit switches push button station, boxes etc for soot blowers solenoid for electromatic relief valves solenoid for hp bypass valves sonic tube assy and sensor housing weld stud / ferrules drum saddle slide bearing plate: ptfe slide bearing on one side and the mirror polished ss sheet on the other side. load bearing capacity upto 200 kg / mm2 disc springs full cone nozzle dsh soot blower pressure reducing valve fuel oil control and trip valves control valve: high pressure steam application gun metal valve hp fill and purge filter assembly intrascope nitrogen blanket system recirculation control valve high pressure startup control valve startup drain control valve direct water level gauge insulation fixing components pins, nuts and washers mateerial ss 310 and304 and carbon steel pin length max 875 mm cfbc refractory for modification refractory for cfbc boiler ceramic wool castable / crushed refractory insulation: calcium silicate slab / block / pipe electro forged floor grills long span fire bricks wool mattress / rtd / pipe section pourable insulation resin bonded wool: material as per astm c 612. thickness 50 mm, density 100 kg / m3 sealing compound ss wiremesh rope woven wire cloth stainless steel steel glazed windows cd. plated / galvanised fasteners pre painted galvanised sheets for boiler roof hea ignitor assy ( oil / gas ) solenoid valves ball valves ( fire safe design ) trip valves ball type control valve and accessories strainers: simplex goggle valve high pressure hoses ( dynamic pressure of 200 bar, static pressure of 290 bar, proof test pressure of 552 bar max, bursting pressure of 1103 bar max ) isolation valves / knife edge gate valves light duty limit switches gear pump with motor ( drain oil ) self actuating valves sump pump motor assembly speed regulator steam trap y type strainers neoprene hoses mill seal air filter assembly oil accumalator ( fuel oil ) actuator: elec. open / close ( damper / gates ) scanner air fan ( with dc motor / ac motor ) scanner air filter elements ash handling plant dynamic shaft seals ss flexible hoses graphite alloy damper bearing and bushings 400 deg c operation butterfly valves ( wafer design ) drag link chain feeder gaskets for coupling rockwell / sleeve couplings variable orifice victaulic / pipe couplings coal handling plant equipment heat resistent glass ( pyrex glass dia 109mm, 5 mm thick, violet / light colour to withstand 500 deg c ) metallic expansion bellows non metallic expansion joints slide bearing plates blowers: tri lobe type. pressure ranging from 0.5 mbar to 1.0 mbar. flow ranging from 2200 nm3 to 20000 nm3. continuous operation. gravimetric feeder assembly solenoid valve ( boi ) boiler circulating water pumps dosing system hydro test pump gravimetric feeder components frp cable trays instrument fittings: brass / ss double compression fittings, cs / as welded fittings, gi threaded fittings teflon hose ( ss braided, flexible ) furnace maintenance platform handling equipment: electrically operated trolly with hoists handling equipment: manually operated mobile platform quick errect scaffolding ( aluminium ) quick erect scaffolding system steel actuator for full bore valve pneumatic actuators for quick closing non return valves inconel gaskets & packing rings airset ( mech ) / air filter / regulator head pulley bush bearings spring washers coal valves clad roller brg. assy strainers: duplex feeder components assembly fittings like male stud olive coupling / elbow / tee, bleeded plug, bulk head union feeder light fittings gaskets gasket eliminator / sealant fuel oil ( triple screw pump ) springs link chains o rings oil seals plug valves metallic seated high pressure rubber hoses sintered flange bronze bushes slip on pipe coupling ss spiral wound gasket tadpole tape fully built electric bus supply of power assisted safety valves pressure reducing valves forged valves hp bypass valves for super critical boilers and angle drain valves safety valves for supercritical boiler special bearing for oil field equipment isolating ball valves pneumatic actuated full valves boiler water recirculating pump chains for soot blowers sdm: fully machined ofe castings machined components for valves zinc and xylan coated fasteners for oil field equipment plc panels for soot blower corrugated al sheet air / oil cylinder for quick closing nrv elastomers for oil field equipment sdm: 12 point cap screw flow bean for oil field equpment feed back transmiter high pressure filter circlips for feeders glass globe / light fitting for feeder fabricator metal component gear box and clean out conveyor drive gear box with motor for soot blowers gear box for valves special glass for water level gauge accumulatars accessories hp bypass system high tensile fasteners limit switch boxes premium threaded ( fox, acme, vamtop, etc., ) body hanger and adaptors non asbestos packings non metallic end covers drive belts pulleys for temperature probe o rings and oil seals aluminium sheet: plain / corrugated air cylinder open / close, retractor assembly special packing set for full bore valves limit switches for quick closing nrv ring joint gasket ( api ) ultrasonic digital thickness gauges with accessories sintered bronze bush soot blower sprocket soft iron gaskets and sealing rings silencers for safety valves swagelock fittings coil springs for safety valves coil springs for safety valves with ibr tc special tools for oil field equipments anhydrous ammonia hose agitator for waste ammonia dilution system ammonia injection skid butterfly valves for dilution air and ammonia injection system dilution air fan & motor assembly including filter de dusting system de nox systems scr dosing tank & pumping system dilution air heater ( electrical ) expansion bellows emergency eye wash & safety shower frp grating hydraulic jack for scr cart ammonia injection control valve ammonia knife edge gate valve anhydrous ammonia pump skid dilution air heater ( steam ) & accessories spray nozzle for spraying sealing rings, retainer rings, drive screws safety selector for tank relief valve spray water self regulating valve fibre glass tadpole tape ammonia trip valves ( ball type, manual, pneumatic & electrical ) anhydrous ammonia truck unloading skid wind indicator water level gauge rings and washers excess flow valves & check valves tunguston carbide balls, bearings, etc for ofe ( oil field equipment ) spiral wound gaskets oil supply unit for hp bypass system teflon o rings, packing rings etc. accumulator manifold keys, pins, washers etc. valve diaphragm actuator valves elec actuators hydraulic actuators & accessories hydraulic power unit proportional valve valves special ( iq ) actuators throttle device for hydraulic power unit washers and circlips teflon slide bearing plate coated abbrasives adaptors api gauges hss circular saw bi metal band saw blades bta tools carbide burrs carbide tipped circular saw disc slitting wheels thread gauges grinding wheels shelf life grinding wheels hss cutting tools carbide cutting tools hacksaw blades high q carbide cutting tools measurnig instruments letter and number punchs special cutters spade drills stellite turning inserts spiral fluted tap symmetrical carbide drills threading taps threading tools tube expanders wrenches indexable carbide drills vdi holders zircon belts te abrasives polytap te boring, facing head alloy steel flats carbon steel strips tubes: erw black is 1161 yst 240 and 10305 alloy steel tubes: sa 213 t11 / t12 / t22 / t23 / t91 / t92 boiler quality carbon steel tubes: sa 210 gr c , sa210 sa192 boiler quality stainless steel tubes: sa 213 tp 347h tp304h / s304h boiler quality alloy steel tubes t91, t92 fused saw flux for drum welding fused saw flux for tube to fin welding gtaw wire for t92 er80s b2 bulk pack gmaw wire gmawwire ernicrfe 7a gmaw wire er 70s a1 gmaw wire er 80s b2 gmaw wire er347 gmaw wire ernicr3 gmaw wire er90s b9 gmaw wire er70s 6 gmaw wire er80s g 1cr mo gmaw wire er90s g 2cr mo gmaw wire for t23. saw flux p91 saw flux for sa335p92 saw wire for sa335p92 f48p2 em12k submerged arc welding flux structural application gtaw rod t92 / p92 gtaw rod er309l er 70s a1 gtaw rod er 80s b2 gtaw rod er 90s b3 gtaw rod gtaw rod tig er347 gtaw rod tig ernicr gtaw rod er90b9 gtaw rod super 304h smaw electrode e7018 a1 smaw electrode e8018 b2 smaw electrode e9018 b3 smaw electrode e9015 b9 smaw elecd t92 / p92 smaw electrode e6013 smaw electrode e7018 smaw electrode e7018 1 e7018 smaw electrode flux cored wire e71t 1 flux cored wire e309t0 1 fcaw wire e309lmoto 1 flux cored wire e81t1 b2 flux cored wire e91t1 b3 bulkpack :e551t1 b2c smaw:hf electrode ecocra smaw electrode ecocr e smaw electrodes enicrfe3 smaw electrode smaw ss electrodes ( e308 16 ) smaw ss electrdes low carbon ( e308l 16 ) smaw electrodes e309 16 smaw electrodes e310 16 smaw electrodes e316 16 smaw electrodes e316l 16 smaw electrodes e347 16 hayness alloy 25 ( ha 25 ) filler rod hayness alloy 21 ( ha 21 ) filler rod ercocr a rod hard facing powder type cocr a hard facing powder type cocr e el 8 saw wire saw wire eb3 saw wire eb2 saw wire ea4 saw wire em12k saw wire eb 9 weldwire saw em12k...

Southern Railway - Tamil Nadu

26807718 supply of , hydraulic jack capacity 50 ton with high pressure hand pump and lock nut (1)hand pump maximum working pressure 10000psi ,pressure can be reduced at any moment during operation,weight with hydraulic oil 10kg approx , robust construction.(2) hosepipe double braided lightweight high pressure hydraulic hose , working pressure 100psiand bursting pressure 20000psi ,high emplies and extremely flexible ,2m length (3) lifting jack compact in size ,weight 25kg approximate with cylinder base and lock nut , retracted height 250mm approximate ,extended height 400mm approximate , capacity 50 ton , working pressure 700 bar ,round cylinder base for extra stability....

Southern Railway - Tamil Nadu

26722346 supply of , hydraulic jack capacity 50 ton with high pressure hand pump and lock nut ( 1 ) hand pump maximum working pressure 10000psi , pressure can be reduced at any moment during operation, weight with hydraulic oil 10kg approx , robust construction. ( 2 ) hosepipe double braided lightweight high pressure hydraulic hose , working pressure 100psiand bursting pressure 20000psi , high emplies and extremely flexible , 2m length ( 3 ) lifting jack compact in size , weight 25kg approximate with cylinder base and lock nut , retracted height 250mm approximate , extended height 400mm approximate , capacity 50 ton , working pressure 700 bar , round cylinder base for extra stability....

Neyveli Lignite Corporation Limited - Tamil Nadu

26506433 supply of hydraulic jack of capacity 100tons, single acting, plain ram with spring return. closed height: 290 320mm, stroke: 150mm (min), out side dia: 210mm (max) port size: 3/8 bsp, working pressure: 550bar,...