Corporation Of Chennai - Tamil Nadu

34073429 hiring of one number of hydraulic excavator (be 200 model or equivalent capacity) for a period of 2 months or 600 hrs (each) whichever is later to use in perungudi dumping ground....

Corporation Of Chennai - Tamil Nadu

34073399 hiring of 2 numbers of hydraulic excavators ( be 200 model or equivalent capacity ) for a period of 2 months or 600 hrs ( each ) whichever is later to use in perungudi dumping ground....

Corporation Of Chennai - Tamil Nadu

34073385 hiring of 2 numbers of hydraulic excavators ( be 200 model or equivalent capacity ) for a period of 2 months or 600 hrs ( each ) whichever is later to use in perungudi dumping ground....

Corporation Of Chennai - Tamil Nadu

33986452 hiring of 2 nos of ex 200 or equivalent model hydraulic excavator for a period of 2 months or 540 hrs each for kodungaiyur dumping ground for koyembedu point...

Corporation Of Chennai - Tamil Nadu

33986026 hiring of 2 nos of ex 200 or equivalent model hydraulic excavator for a period of 2 months or 540 hrs each for kodungaiyur dumping ground for taurus and tipper point...

Corporation Of Chennai - Tamil Nadu

33986015 package 1 / 2022 hiring of 2 nos of ex 200 or equivalent model hydraulic excavator for a period of 2 months or 540 hrs each. for kodungaiyur dumping ground for compactor point...

Indian Oil Corporation Limited - Tamil Nadu

33743449 supply and installation of scissor lift for handling 425kg capacity cylinders at lpg bottling plant, salem, tamil nadu. supply and installation of scissor lift for handling 425kg capacity cylinders at lpg bottling plant, salem, tamil nadu. , supply & installation of manually operated scissor lift for 425kg capacity cylinders . , earth work in excavatiion in all kinds of soilby mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place. , providing and laying in position cement concrete of1:1½:3(1 cement :1½ coarse sand: 2 graded stone aggregate of 20mm) excluding cost of centering & shuttering. all work up to plinth level: , providing and laying brick work in cement mortar 1:4 (1 cement : 4 coarse sand)in foundation and plinth with common burnt clay f.p.s (non modular) bricks of class designation 7.5 in foundation & plinth , providing and laying 20mm cement plaster of mix 1:4 (1 cement: 4 fine sand)on surfaces with fine sand including curing etc. => limited...

Ministry Of Coal - Tamil Nadu

33740323 bids are invited for a type teeth for 700 litres capacity bucket wheel excavator (q3) , b type teeth for 700 litres capacity bucket wheel excavator (q3) , e type teeth for 700 litres capacity bucket wheel excavator (q3) , f typeteeth for 700 litres capacity bucket wheelexcavator (q3) total quantity : 3049...

Ministry Of Coal - Tamil Nadu

33739576 bids are invited for sm461570090: c type teeth for 700 litres capacity bucket wheel excavator ( q3 ) , sm461570091: d type teeth for 700 litres capacity bucket wheelexcavator ( q3 ) total quantity : 3463...

Ministry Of Coal - Tamil Nadu

33662506 bids are invited for sm461570088: a type teeth for 700 litres capacity bucket wheel excavator ( q3 ) , sm461570093: f type teeth for 700 litres capacity bucket wheelexcavator ( q3 ) total quantity : 600...

Corporation Of Chennai - Tamil Nadu

33656712 hiring of front end loaders with back hoe 400 hours and poclain hydraulic excavator 200 hours in unit 44, div 192, 194, 197 and199, zone 15 ...

Corporation Of Chennai - Tamil Nadu

33656704 hiring of front end loaders with back hoe 400 hours and poclain hydraulic excavator 200 hours in unit 45, div 193, 195, 196, 198 and 200, zone 15 ...

Corporation Of Chennai - Tamil Nadu

33652652 hiring of 2 nos. of hydraulic excavator ( ex 200 model or equivalent capacity ) for a period of 3 months or 720 hrs ( each ) whichever is later for perungudi dumping ground h ...

Corporation Of Chennai - Tamil Nadu

33652546 hiring of 2 nos. of hydraulic excavator ( ex 200 model or equivalent capacity ) for a period of 3 months or 720 hrs ( each ) whichever is later for perungudi dumping ground ...

Private Company - Tamil Nadu

33596903 auction sale of dcbl dalmiapuram material generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 13 of 65 copyright rights 1 6120548 filter bag,131 x 4191 mm,for cvrm 1 2 6164272 torque weldment assembly,drg:10053315,pls:50005801,itm:06,flsmidth,sht :01.01.01,spares for cfg clinker cooler,make:flsmi 3 6114459 end cover inlet, drg:552 cm1 2 mp 327 0, spares for cement mill 2 4 6113410 driven sprocket wheel, with bushing, cfg 5 6182280 cross head assembly, pn:111 81 3 1928, dwg:50005808,01.01.01.03,spares for cooler,make:fls,1272 cis/cfg/rft 6 6119989 hammer, drg:45n cc1 3 mp 302 0,spares for clinker crusher 7 6118660 connection clamp,motor rating:30 kw,1465 rpm,spares for belt elevator,bw g400/2,make:aumund 8 6124534 low energy grate plate,pos:04,spares for cooler,make:flsmidth,cfg 1272 hw/1107 cismfr 9 6120881 rft dead grate plate lh,of kiln,drg:45n gc1 2 mp 308 0,spares for cooler,make:flsmidth 10 6120882 rft dead grate plate rh,of kiln,drg:45n gc1 2 mp 307 0,spares for cooler,make:flsmidth 11 6112786 insulator,porcelain,spares for current transformer 12 6117326 body wear liner,of ks tripple gate feeder,drg:531 fv1 3 mp 301,spares for cvrm 3 13 6121257 conveyor belt,skirted,endless,nylon,m 24,800 kn/m,ply:4 ply,thk(top/bot):5 mm/2 mm,wd:650 mm,lg:4980 mm,tolerance for belt lg: +/ 1 mm 14 6111742 expansion valve 15 6119515 bellow,spares for coal tippler,make:khd 16 6124527 regulator,pos:013,pn:1601604,spares for cooler,make:flsmidth,cfg 1272 hw/1107 cismfr 17 6132432 piston 47piston (47) 18 6128379 damper plate,pn:2170063350,serial no:a a0051,spares for lp compressor,tbtdrm,make:kirloskar pneumatic company 19 6131626 seal kit for power cylinderseal kit for power cylinder 20 6091547 sprocket,duplex,forged carbon steel,13 teeth,pitch:3 inch,for cooler,make:fls,min bhn.300 21 6117602 hanger bearing assy,sc,spares for vrm 1 esp 22 6105852 coupling,pin bush,elecon fc 16,for vrm2 esp fan 23 6131807 hose pn 40nb 1200lg sw female connectorsatend for mu lticor spil mat.code i120055015 parts group mechanica l multicor k 80 spil ifo o 6111003000 eqpt refic611 100300022004008012 016 make schenck process india ltd hose, pn 40nb 1200lg, sw female generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 15 of 65 copyright rights 24 feeder,drg:531 fv1 3 mp 302,spares for cvrm 3 25 6100952 holding beam,of esp collecting electrode,spares for mill(vrm 2) 26 6120767 belt sway switch,800/1000/1400/1600 mm b/w,spares for weigh feeder 27 6119592 solenoid valve,model: lsks 66 c/s,spares for pneumatic jet bag filter,make:polysius 28 6117965 drive sprocket,equipment tag no:l21 cv2,spares for conveyor 29 6117591 non drive sprocket,76 t,drg:351 ep1 1 ms 303 0,spares for vrm 2 esp 30 6112173 spur pinion,66 teeth,drg:76 4,for rm elevator,make:polysius,spares for gear box 31 6102335 sprocket,57 teeth,drg:351 ep1 3 mp 335 0,of esp rapping driven (collecting plate),spares for mill(vrm 2),make:andrew yule 32 6131612 silicon seal kit,for ivgk model,size:100nb butterfly valve,make:intervalve,ed 40/a,serial no:25647. 33 6119136 shaft,pn:113ad51113,make:beml 34 6118796 propeller shaft,pn:346202000000 35 6112174 spur pinion,ref:247,drg:76 4,for rm elevator,make:polysius,spares for gear box 36 6119278 dirty oil pump,spares for transformer oil filtering unit generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 16 of 65 37 6127487 for excavator,ex1200,make:telcon(tata hitachi) 38 6095627 brake nester cylinder assy,pn:02013068,spares for forklift,g300d,make:godrej 39 6124251 solenoid valve,spares for raw mill(vrm),lm 46.4,make:loesche 40 6119594 elbow,bronze,spares for pneumatic jet bag filter,make:polysius 41 6113757 hammer pin,spares for clinker crusher 42 6107129 sealing set,of hoisting cylinder assy,pn:b6360504301,spares for front end loader,636,make:beml 43 6097601 cross switch,pn:81 139,make:roots,spares for road sweeping machine,1700d,hako 44 6097652 cad contact,drg:313 115,for starter 45 6129926 brake lining,pn:8602551,spares for hydraulic mobil crane,hydra 10,make:escorts 46 6122344 ferrule female fitting,pn:sar09178,spares for printing machine,make:video jet 47 6108814 bucket attachment pin,of chassis system,pn:3034300,spares for excavator,uh083lc,make:tata hitachi 48 6108759 pin,of hydraulic system,pn:3034301,spares for excavator,uh083lc,make:tata hitachi 49 6108812 pin,of chassis system,pn:3034299,spares for excavator,uh083lc,make:tata hitachi50 6118843 repair kit,of ut lift cylinder,pn:340627000001,spares for loader,1420z,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 17 of 65 51 6103989 for blower,sr091,make:kulkarni 52 6107251 operating soft shaft,pn:z0105306618,spares for loader,636,make:beml 53 6099960 slip ring assembly,ref:315 8,750 rpm,spares for motor,3 ph,225 kw,3.3 kv,50 hz,make:bhel 54 6108816 hose,of chassis system,pn:4142888 page154/13,spares for excavator,uh083lc,make:tata hitachi 55 6106860 o ring,of transmission system,pn:0634313049,spares for loader,1420z,make:beml 56 6107045 seal kit,of hydraulic system,pn:iw350614022000/5 21 20,spares for loader,1420z,make:beml 57 6109857 trans filter element,return oil,pn:w0104317204,spares for loader,636,make:beml 58 6097696 contact,drg:313 88a,pn:60009,spares for oh crane 59 6096099 ignition switch,ref:13.695,spares for road sweeping machine,1300dy,dulevo 60 6097697 contact,pn:21s,drg:313 88d,spares for oh crane 61 6107189 pin assy,pn:344900040000,spares for front end loader,1420z,make:beml 62 6107063 engine fuel filter,pn:13020488,spares for loader,636,make:beml 63 6107147 turbine boss,pn:w0104311028,spares for front end loader,636,make:beml 64 6055689 solenoid valve assy,pn:25/220998,itm:30,spares for backhoe loader,3dx,make:jcb 65 6107155 stator boss,pn:w0104311005,spares for loader,636,make:beml 66 6107073 brake hoof,pn:z0104322921,spares for loader,636,make:beml 67 6107153 impeller boss,pn:w0104311021,spares for front end loader,636,make:beml 68 6107353 tube,of distribution valve,pn:z0105306022,spares for loader,636,make:beml 69 6106841 transmission element,pn:230962,spares for loader,1420z,make:beml 70 6116434 shacking filter,for electric motor,cs rim,pn:d671300000 71 6112588 extraction gate seal kit,make:dycat,spares for clinker silo 72 6107047 seal set,pn:iw34062000000/5 39 26,spares for loader,1420z,make:beml 73 6107070 return oil filter t/m,pn:w0104317200,spares for loader,636,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 19 of 65 copyright rights 74 6108821 bellow expansion joint,pn:td00605,spares for excavator,ex200lc,make:tata hitachi 75 6121608 air slide box gasket,for fls rabh bottom,flsmidth,drg:fls std 4 mp 301 0,serial no:3 76 6095397 o ring,of spring cylinder,pos:60,size:350/140 220st use,spares for raw mill (vrm 2),lm 30.31,make:loesche 77 6117596 link,andrew yule,drg:sp 192 1/576,drg:351 ep1 4 mp 307 0,spares for vrm 2 esp 78 6108871 coupling,of hydraulic system,pn:4069801,spares for excavator,uh083lc,make:tata hitachi 79 6107220 suction hydraulic oil filter,spares for loader,636,make:beml 80 6107146 stator,pn:w0104311027,spares for front end loader,636,make:beml 81 6108799 collar,of transmission system,pn:td00352/02 pg138/95,spares for excavator,uh083lc,make:tata hitachi 82 6122819 hydraulic pump,ref:rt 10,serial no:301092503 83 6106824 hose,dia:1 1/4 inch x lg:640 mm,insap12,of hydraulic system,pn:3406 3231 0000,spares for loader,1420z,make:beml 84 6108763 needle bearing,of hydraulic system,pn:4126657,spares for excavator,uh083lc,make:tata hitachi generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 20 of 65 85 6101906 brush holder,drg:313 114,spares for motor 86 6106878 pin assy,of chassis system,pn:34405010001,spares for loader,1420z,make:beml 87 6107059 hydraulic oil filter return,spares for loader,636,make:beml 88 6092153 air filter element,20 x 10 x 3 1/4 inch,pn:45016200y,spares for compressor,2vyd210,make:kg khosla 89 6096189 ballast choke,for metal halide lamp,voltage rating:230 vac,power rating:50 w 90 6102173 slip ring,spares for motor,25 hp,720 rpm 91 6097861 arcing contact cmprn spring,make:fls,for ocb,200 350 a 92 6103623 high pressure flexible hose,1/4 inch x lg:1 m,spares for inert gas generator 93 6108804 teeth,of chassis system,pn:4501626,pn:tb00147,spares for excavator,uh083lc,make:tata hitachi 94 6106864 cross & bearing,of chassis system,pn:iw346201010000,spares for loader,1420z,make:beml 95 6107136 drive pump shaft,pn:w0104311002,spares for front end loader,636,make: 96 6106882 h frame bush top,of chassis system,pn:344900000930,spares for loader,1420z,make:beml 97 6129023 brake shoe front & rear,pn:86.02.36.1,spares for crane,hydra 12 sb,12 ton,make:escorts 98 6107066 engine air filter outer,pn:13022638,spares for loader,636,make:beml 99 6107044 seal kit,of hydraulic system,pn:iw350614011800/5 31 18,spares for loader,1420z,make:beml 100 6108751 bolt,of chassis system,pn:j932721,spares for excavator,uh083lc,make:tata hitachi 101 6099964 slip ring assembly,of engine & elmr,pn:710407,spares for lt motor,115 hp 102 6094563 suction valve plate,of cr 105,pn:35383200a,spares for compressor,2vyd210,make:kg khosla 103 6107168 planet gear,frame,pn:z0104304211,spares for loader,xz636,make:beml 104 6107125 pin rear,of front frame assy,pn:z0104302206,spares for loader,636,make:beml 105 6106850 vent valve,of transmission system,pn:0507205154,spares for loader,1420z,make:beml 106 6106870 bush,of chassis system,pn:344900000230 f408/11,spares for loader,1420z,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 22 of 65 copyright rights 107 6106880 spacer,of chassis system,pn:344405000330,spares for loader,1420z,make:beml 108 6107162 shaft seal,pn:355ax94482,spares for loader,1420,make:beml 109 6096253 pin assy,pn:344900030000,spares for truck,1612,tata 110 6107052 bush,of hydraulic system,pn:344900001030,spares for loader,1420z,make:beml 111 6107217 bell crank link bush,of chassis system,pn:344900000330,spares for loader,1420z,make:beml 112 6117590 drive sprocket,15 t,rap,drg:351 ep1 3 mp 335 0 .,spares for vrm 2 esp 113 6096187 choke,for lamp,voltage rating:230 vac,power rating:20 w 114 6107042 repair kit,of flow amplifier,pn:345410053100,spares for loader,1420z,make:beml 115 6107149 needle bearing,pn:b0704074106,spares for front end loader,636,make:beml 116 6127457 pin assy,of hydraulic system,pn:347033000003,also for truck,make:tata,1612,spares for loader,1420z,make:beml 117 6106862 o ring,of transmission system,pn:0634313487,spares for loader,1420z,make:beml 118 6107075 edge teeth lh,pn:z0105310513,spares for loader,636,make:beml 119 6107076 edge teeth rh,pn:z0105310514,spares for loader,636,make:beml 120 6092111 protection grill,pn:r79/g/45258120m,spares for compressor,2vyd210,make:kg khosla 121 6103983 lip seal,pn:100156,serial no:2007,spares for blower,sr091,make:kulkarni 122 6107111 rocker arm shaft,pn:z0105311203,spares for loader,xz636,make:beml 123 6200540 brake slack adjuster,diesel,pn:mh02018612,spares for forklift,g300d,make:godrej 124 6107055 wiper seal,of hydraulic system,pn:350614020100,spares for loader,1420z,make:beml 125 6127061 valve,spool,3 way,single solenoid operated,1/4 inch bsp,schrader,drg:ps 021/86,single solenoid operated,for khd cooler 126 6101839 brush holder,drg:313 116,spares for motor,make:kirloskar 127 6106888 ball bearing,of chassis system,pn:vy 2917fafnir s1100k,spares for loader,1420z,make:beml 128 6107043 dust seal,of hydraulic system,pn:iw344900000140,spares for loader,1420z,make:beml 129 6108118 oil seal,pn:8431341,spares for loader,636,make:beml 130 6108114 bearing pad,pn:8589910,spares for loader,636,make:beml 6093813 131 driving plate,aluminium,pn:f3031814,spares for engine,alu 370,make:ashok leylan 132 6097651 electrical contact,drg:313 105b,for starter 133 6107164 bearing,pn:3000210,spares for loader,636,make:beml 134 6097854 moving arcing contact spring,make:fls,for ocb,60 100 a 135 6117597 end piece thread rod,with rapping,emitting frame support pipe,spares for vrm 2 esp 136 6106859 o ring,of transmission system,pn:0634313369,spares for loader,1420z,make:beml 137 6106863 rod end,of chassis system,pn:ik1548117150,spares for loader,1420z,make:beml 138 6106817 o ring,of hydraulic system,pn:iwvg9096/5 7 58,spares for loader,1420z,make:beml 139 6107041 oil seal,of hydraulic system,pn:kk0701210085,spares for loader,1420z,make:beml 140 6096815 spd clutch repair kit,pn:871.000,spares for hydraulic mobil crane,hydra 10,make:escorts 141 6097198 tubular rivet,pn:8602560,spares for hydraulic mobil crane,hydra 10,make:escorts 142 6103985 sleeve,pn:7817k,serial no:2007,spares for blower,sr091,make:kulkarni 143 6103984 sleeve,pn:6932,serial no:2007,spares for blower,sr091,make:kulkarni 144 6097689 contact,drg:313 89c,spares for crane 145 6097692 contact,cli,drg:313 89a,spares for crane 146 6093758 bearing set,for connecting rodnor, pn:0211310434jt10f202,spares for engine,697 tc,make:tata 147 6129722 support assy rear,rubber,pn:257624200118,spares for engine,697 tc,make:tata 148 6106848 vent valve,of transmission system,pn:0732612001,spares for loader,1420z,make:beml 149 6107053 seal carrier assy,pn:350614011200,spares for loader,1420z,make:beml 150 6107124 bearing sheu,of front frame assy,pn:w0104302003,spares for loader,636,make:beml 151 6107169 sun gear,frame,pn:z0104304215,spares for loader,xz636,make:beml 152 6107143 bearing,pn:b0702120000,spares for front end loader,636,make:beml 153 6119593 make and brake contact,model: lsks 66 c/s,spares for pneumatic jet bag filter,make:polysius 154 6107150 bearing,pn:b0702060000,spares for front end loader,636,make:beml 155 6106826 hose,pn:340632440000,pn:34230002,spares for loader,1420z,make:beml 6106891 156 o ring,of chassis system,pn:chs0105340,spares for 157 6105559 knife edge,spares for weigh feeder,make:transweigh 158 6107152 isolating ring,pn:w0104311024,spares for front end loader,636,make:beml 159 6107126 pin rear,of front frame assy,pn:z0104302205,spares for loader,xz636,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 26 of 65 copyright rights 160 6097650 contact,drg:313 105a,for starter 161 6097688 electrical contact,drg:313 89,spares for crane 162 6107140 bearing,pn:b0703100000,spares for front end loader,636,make:beml 163 6101902 o ring,pn:80579800,spares for raw mill,lm 46.2+2,make:loesche 164 6107236 coupling sleeve,of hydraulic system,pn:w0104319016,spares for loader,636,make:beml 165 6116248 distance ring,of cooler crank drive,is 2062,spares for kiln,make:khd 166 6200542 brake cylinder,pn:mh2570802,spares for forklift,g300d,make:godrej 167 6106879 spacer,of chassis system,pn:344405000230,spares for loader,1420z,make:beml 168 6089693 pressure switch,pn:4055075,spares for engine,nt495c,make:cummins generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 27 of 65 copyright rights reserved. 169 6168295 cold vulcanizing adhesive,sk811 a,for conveyor belt joining purpose. 170 6107138 bearing,pn:b0703080000,spares for front end loader,636,make:beml 171 6010277 w.a pivot pin,pn:646/04622,spares for payloader,3d,make:jcb 172 6174354 bush,for boom assy,pn:y05.26.11.o,spares for crane,hydra 10/058,make:escorts 173 6107137 bearing,pn:b0703070000,spares for front end loader,636,make:beml 174 6106816 o ring,pn:8431345,spares for loader,636,make:beml 175 6092104 suction valve plate,pn:r79/j/38102660p,spares for compressor,2vyd210,make:kg khosla 176 6106810 o ring,pn:8431532,spares for loader,636,make:beml 177 6117598 end piece thread rod,without rapping,emitting frame support pipe,spares for vrm 2 esp 178 6097694 contact,drg:313 86b,pn:70021,spares for oh crane 179 6107061 bolt,pn:b0100016060,spares for loader,636,make:beml 180 6096011 cylinder gasket kit,ref:1842,pn:c38d800000,spares for road sweeping machine,1300dy,dulevo generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 28 of 65 181 6100726 insulator,porcelain,of channel support,spares for crane 182 6106889 o ring,of chassis system,pn:chs0106250,spares for loader,1420z,make:beml 183 6097757 contact,drg:313 105a2,for switch 184 6106857 o ring,of transmission system,pn:0634306519,spares for loader,1420z,make:beml 185 6107072 brake shoe,pn:z0104508107,spares for loader,636,make:beml 186 6106809 o ring,pn:8431531,spares for loader,636,make:beml 187 6107110 pin shaft assy,pn:z0105311201,spares for loader,xz636,make:beml 188 6107112 pin shaft assy,pn:z0105311204,spares for loader,xz636,make:beml 189 6106890 o ring,pn:chs0105280,spares for loader,1420z,make:beml 190 6107154 coupling sleeve,pn:w0104317008,spares for loader,636,make:beml 191 6106792 o ring,crown (main reductor) assy,pn:z0104304206,spares for loader,636,make:beml 192 6122826 seal kit,spares for 3 way chute valve,make:khd aumund generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 29 of 65 copyright rights 193 6107071 o ring,pn:b0700131115,spares for loader,636,make:beml 194 6096009 oil filter cartridge,pn:d733100000,spares for road sweeping machine,1300dy,dulevo 195 6119595 manifolding rack,spares for pneumatic jet bag filter,make:polysius 196 6129089 catcher plate,pn:38102200n,spares for compressor,2vyd210,make:kg khosla 197 6108808 oil strainer upper,of chassis system,pn:9te00188,spares for excavator,uh083lc,make:tata hitachi 198 6129060 spare kit,l&t,cat:ss90896,for contactor,mm:ml 1,coil voltage:440/220 vac,10a 199 6096012 gasket kit,pn:c38n600000,spares for road sweeping machine,1300dy,dulevo 200 6106815 o ring,pn:8431344,spares for loader,636,make:beml 201 6129583 backup ring,of hydraulic system,itm:8,pn:4085607,spares for excavator,ex1200,uh083lc,make:telcon(tata hitachi) 202 6107058 element,of hydraulic system,pn:1546012170,spares for loader,1420z,make:beml 203 6124355 o ring,pn:qv100132,spares for air blaster,100 l,make:mm fabricators 204 6092155 piston,dia:35 mm,pn:35320240f(plg),spares for compressor,2vyd210,make:kg khosla 205 6093770 axle shaft rear,pn:257635707005,spares for engine,697 tc,make:tata 206 6102147 slip ring,pn:0121686a,spares for ht motor,250 hp 207 6129088 catcher plate,pn:35332160n,spares for compressor,2ha2ter,2vyd,make:kg khosla 208 6129203 gm bush small end/upper end,pn:a/37098120a,spares for compressor,2vyd210,make:kg khosla 209 6124847 travel hose,telcon(tata hitachi),pn:4313352,spares for excavator,ex1200,make:telcon(tata hitachi) 210 6095166 air filter indicator,pn:p896701,spares for compressor,make:elgi 211 6106788 switch,pn:iw560800130000,pn:td9427/1 13 14,spares for loader,636,make:beml 212 6106846 o ring,of transmission system,pn:227672,spares for loader,1420z,make:beml 213 6107682 return spring front & rear axle,front & rear axle,pn:81008663,spares for loader,2021,make:hindustan motors,make:caterpillar 214 6108805 voltage sensitive relay assy,of chassis system,pn:te00793,spares for excavator,uh083lc,make:tata hitachi generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 31 of 65 copyright rights reserved. 215 6107048 steering seal kit,of hydraulic system,pn:340649000000,spares for loader,1420z,make:beml 216 6097119 oil seal,of front end,pn:b0900112013,spares for wheel loader,636,make:beml 217 6130663 bolt,pn:f3533211,for engine,hydraulic system,model:90ck,make:l&t,spares for water sprinkler,comet super,ashok leyland 218 6120888 seal kit,3 inch,spares for cooler double flap 219 6107068 v belt,pn:2234343,spares for loader,636,make:beml 220 6124846 travel hose,telcon(tata hitachi),pn:4473993,spares for excavator,ex1200,make:telcon(tata hitachi) 221 6107054 wiper,of hydraulic system,pn:350614011400,spares for loader,1420z,make:beml 222 6094114 high pressure piston,dia:70 mm,pn:34136360w,spares for ect compressor,2ha2ter,make:kg khosla 223 6106786 o ring,pn:6498564391000242/2 13 4,spares for loader,1420z,make:beml 224 6106843 band seal,of transmission system,pn:228931,ref:fig 202/05,spares for loader,1420z,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 32 of 65 copyright rights 225 6097045 oil reservor brake,pn:v19490470,spares for crane,hydra 10,make:escorts 226 6128982 high pressure hose,pn:v19 45 048 1,spares for hydrau lic mobil crane,hydra 10,12 ton,make:escorts 227 6129435 o ring,pn:a811110,spares for excavator,ex600,ex600v,make:telcon(tata hitachi) 228 6106829 hose,of hydraulic system,pn:iw340601000642/5 49 18,spares for loader,1420z,make:beml 229 6126396 flow regulator hose,telcon(tata hitachi),pn:4392311,spares for excavator,ex1200,make:telcon(tata hitachi) 230 6117594 roller,for rapping,drg:351 ep1 4 mp 336 0,spares for vrm 2 esp 231 6103030 pad,nylon,main frame & boom assy,pn:v19261730,spares for hydra crane,12 mton,make:escort 232 6113498 o ring,150 x 7,for khd cooler,spares for grease pump,zpu 14 233 6107145 o ring,338 x 3.5 mm,pn:b0600135338,spares for front end loader,636,make:beml 234 6092114 relief valve body,pn:35120043m,spares for compressor,2vyd210,make:kg khosla 235 6118971 gear pump joint bush,of steering hydraulic system,pn:z010431700,spares for loader,636,make: 236 6120127 plummer block,of cabin drive shaft,drg:j31ca23mp3450,spares for oh crane,make:polysius 237 6108104 relay,pn:w7482000009,spares for loader,636,make: 238 6110401 bearing,make:timken,pn:hm803110,pn:hm803149,spares for loader,3dx,make:jcb 239 6096029 hose,metal,lg:1400 mm,valve bank to front brush,ref:drso,spares for road sweeping machine,1300dy,dulevo 240 6096030 hose,lg:1500 mm,blower motor to central brush,ref:drs07,spares for road sweeping machine,1300dy,dulevo 241 6108116 oil seal,pn:8431539,spares for loader,636,make:beml 242 6108117 oil seal,pn:8431546,spares for loader,636,make:beml 243 6106842 retainer filter,of transmission system,pn:236801010610,spares for loader,1420z,make:beml 244 6124831 pilot hose,telcon(tata hitachi),pn:4364775,spares excavator,ex1200,make:telcon(tata hitachi) generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 34 of 65 copyright rights 245 6108102 relay,pn:w7750000042,spares for loader,636,make:beml 246 6092105 washer,100 x 92 x 2 mm,pn:g/45430130j,spares for compressor,2vyd210,make:kg khosla 247 6092102 washer,91 x 87.4 x 1 mm,pn:h/45330360n,spares for compressor,2vyd210,make:kg khosla 248 6092113 delivery ball valve,pn:45112080h,spares for compressor,2vyd210,make:kg khosla 249 6102172 slip ring,mpv,spares for lt motor,120 hp 250 6128396 delivery valve bell,pn:35112040,spares for compressor,2vyd,2ha2ter,make:kg khosla 251 6106856 o ring,of transmission system,pn:25k030020,spares for loader,1420z,make:beml 252 6130561 back nut,pn:130 99534,pn:1356/0204z,spares for pay loader,3dx,3d,make:jcb 253 6096017 hose,lg:500 mm,hydraulic tank to service pump,ref:drs01,spares for road sweeping machine,1300dy,dulevo 254 6132615 o ring for cylinder liner part.no130601252o ring for cylinder liner, (part.no:130601252) 255 6111999 receiver valve,spares for air dryer,make:gem 256 6107557 hose assy,pn:9194159,spares for loader,2021,make:hindustan motors 3generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 35 of 65 257 6106811 spring,pn:8431533,spares for loader,636,make:beml 258 6106789 speedometer cable,spares for loader,636,make:beml 259 6130664 washer special,pn:f4933715,10 kl,for engine,hydraulic system,model:90ck,make:l&t,spares for water sprinkler,comet super,ashok leylan 260 6093769 gasket,pn:252514115301,spares for engine,697 tc,make:tata 261 6093771 high pressure hose assy,3/8 inch,pn:257344105803t40p183,spares for engine,697 tc,make:tata 262 6108540 hose,pn:s03231976,spares for excavator,cu 90 3,make:l&t 263 6106812 spring,pn:8431534,spares for loader,636,make:beml 264 6097061 repair kit,wheel cylinder,pn:69967137,spares for hydraulic mobil crane,hydra 10,make:escorts 265 6108866 coupling,of hydraulic system,pn:94071215,spares excavator,uh083lc,make:tata hitachi 266 6107062 nut,pn:b0300116001,spares for loader,636,make:beml 267 6106793 gasket,pn:z0104304221,spares for loader,636,make:beml generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 36 of 65 268 6108870 page10/7,spares for excavator,uh083lc,make:tata hitachi 269 6108809 bushing,of chassis system,pn:3028934,spares for excavator,uh083lc,make:tata hitachi 270 6097847 contact,drg:313 98e,for ocb 271 6106813 spring,pn:8431334,spares for loader,636,make:beml 272 6106814 spring,pn:8431335,spares for loader,636,make:beml 273 6129303 slew raw plunger seal,pn:14060015,spares for loader,3dx,make:jcb 274 6093768 cover top,for different filter,pn:945103532f42t7pg29,spares for engine,697 tc,make:tata 275 6108103 relay,pn:z7750000002,spares for loader,636,make: 276 6093766 hose,rubber,pn:3129976182,spares for engine,697 tc,make:tata 277 6108111 bulb,pn:z7581000016,spares for loader,636,make: 278 6107139 oil seal,pn:b0900108222,spares for front end loader,636,make:beml 279 6093767 bed front,pn:3122201417,spares for engine,697 tc,make:tata generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 37 of 65 280 6095618 brake return spring,pn:02025670,spares for forklift,g300d,make:godrej 281 6107142 seal ring,80,pn:w0104311019,spares for front end loader,636,make:beml 282 6108810 dust seal,of chassis system,pn:4084578,spares for excavator,uh083lc,make:tata hitachi 283 6174352 castle nut,for main frame & boom assy,pn:n1.30x1.5,spares for crane,hydra 10/058,make:escorts 284 6106847 circlip internal,of transmission system,pn:340623001230,spares for loader,1420z,make:beml 285 6092101 piston ring,dia:250 mm,pn:a/35324280x,spares for compressor,2vyd210,make:kg khosla 286 6092106 gasket,of c.case & pin guide,pn:a/45230320m,spares for compressor,2vyd210,make:kg khosla 287 6092107 piston ring,dia:210 mm,pn:a/45324400h,spares for compressor,2vyd210,make:kg khosla 288 6092108 cylinder head gasket,pn:b/45230800w,spares for compressor,2vyd210,make:kg khosla 289 6093762 piston pin,with circlip,spares for engine,697 tc,make:tata 290 6093765 head gasket assy,ref:728 ds,spares for engine,697 tc,make:tata generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 38 of 65 copyright rights 291 6092103 gudgeon pin,pn:b/37270280n,spares for compressor,2vyd210,make:kg khosla 292 6093760 bush,for normal,pn:3520381150,spares for engine,697 tc,make:tata 293 6097848 contact,drg:313 98f,for ocb 294 6108538 hose,pn:u01031982,spares for excavator,cu 90 3,make:l&t 295 6107060 sealing,pn:z0104320006,spares for loader,636,make:beml 296 6108800 pack up ring,of transmission system,pn:4038533,spares for excavator,uh083lc,make:tata hitachi 297 6107806 seal ring,of transmission,pn:6750558,spares for loader,2021,make:hindustan motors 298 6174350 castle nut,for lower structure assy,pn:n7.20x2,spares for crane,hydra 10/058,make:escorts 299 6132617 ring teflon for vertical pistonpart.no210005014ring teflon for vertical piston,(part.no:210005014) 300 6107807 gasket,of transmission,pn:6772740,spares for loader,2021,make:hindustan motors 301 6092100 oil ring,dia:210 mm,pn:a/35324120x,spares for compressor,2vyd210,make:kg khosla generated on: 17th aug 2022 11:56:21 | website: https://www.mjvaluemart.com/ | page: 39 of 65 302 6107141 seal ring,60,pn:w0104311008,spares for front end loader,636,make:beml 303 6106892 hose,of chassis system,ref:505062,spares for loader,1420z,make:beml 304 6108110 bulb,pn:z7581000012,spares for loader,636,make:beml 305 6108108 fuse,pn:x7482000004,spares for loader,636,make:beml 306 6093774 o ring,spares for engine 307 6106791 sump cover packing,spares for loader,636,make:beml 308 6108105 fuse,pn:x7482000001,spares for loader,636,make:beml 309 6108106 fuse,pn:x7482000010,spares for loader,636,make:beml 310 6108107 fuse,pn:x7482000011,spares for loader,636,make:beml 311 6093764 major gasket,pn:252501000405,spares for engine,697 tc,make:tata 312 6108541 lub oil pressure switch,pn:b20041649,spares for excavator,cu 90 3,make:l&t 313 6106808 seal kit,of lock valve,pn:8346000,spares for loader,636,make:beml 314 6095297 flat ring(oil resistant),rubber,ref:sh 50 55,spares for compressor,make:elgi 315 6129438 o ring,of hydraulic system,pn:a810160,spares for excavator,ex600,ex200,ex1200,make:telcon(tata hitachi) 316 6108109 fuse,pn:x7482000025,spares for loader,636,make:beml 317 6107046 spring,of hydraulic system,pn:tg3055/3 5 11,spares for loader,1420z,make:beml 318 6093772 hose,rubber,for:excavator,pn:252509135828,spares for engine,697 tc,make:tata 319 6106865 retainer,of chassis system,pn:346300000330,spares for loader,1420z,make:beml 320 6106821 o ring,of hydraulic system,pn:iwif3232vj0579/5 7 47,spares for loader,1420z,make:beml 321 6108535 o ring,pn:p20030414,spares for excavator,cu 90 3,make:l&t 322 6106818 o ring,of hydraulic system,pn:564300005241,ref:tf5195,spares for loader,1420z,make:beml 323 6106820 o ring,of hydraulic system,pn:sv2580/5 49 22,spares for loader,1420z,make:beml etc...

Municipal Adminitration And Water Supply Department - Tamil Nadu

33567753 hiring of excavator ex 200 normal boom length and engaging excavator for managing handling of the incoming municipal solid wastes dumped for heaping in the open land at vellalore site. hiring of excavator ex 200 normal boom length and engaging excavator for managing handling of the incoming municipal solid wastes dumped for heaping in the open land at vellalore site. roc no 1775 / 2022 / md4...

Municipal Adminitration And Water Supply Department - Tamil Nadu

33567712 hiring of excavator ex 200 with 9 m boom length and stitch for managing handling of the incoming municipal soild wastes dumped for heaping in the open land at vellalore site hiring of excavator ex 200 with 9 m boom length and stitch for managing handling of the incoming municipal soild wastes dumped for heaping in the open land at vellalore site...

Corporation Of Chennai - Tamil Nadu

33557347 z.o.iv.c.no.b3/0642/2022 providing tipper lorries, front end loaders and hydraulic excavators on rent basis in zone iv z.o.iv.c.no.b3/0642/2022 providing tipper lorries, front end loaders and hydraulic excavators on rent basis in zone iv => limited...

Corporation Of Chennai - Tamil Nadu

33473027 m.e.d. n.c.d c.no.b4/470/2022 hiring of 02 nos private operators for operating hydraulic excavator bearing number ne_3 and ne_8 deployed at kodungaiyur dumping ground...

Corporation Of Chennai - Tamil Nadu

33473026 m.e.d. n.c.d c.no.b4/467/2022 hiring of 02 nos private operators for operating hydraulic excavator bearing number ne_5 and ne_9 deployed at kodungaiyur dumping ground...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

33472997 school building renovation work school building renovation work , school building renovation work , bushes cleaning around the school building by using jcb excavator retal basis , dismantling of old flooring & wall including necessary tool & breaking machines and labours charges etc , flooring with cement concrete 1:5:10, 40mm metal 100mm thick and plasterd over with cement mortor 1:3 20mm thick including cost of all material and labour charges etc , brick work in cement mortar 1:5 using country bricks 8 ¾” x4 ¼” x2 ½” including cost of all materials and labour charges & curing etc , plastering work in cement mortor 1:5 12mm thick inclusing cost of all material and labourcharges and curing etc , supply and fixing new ac sheet including cost of all material and labour charges etc , colour washing two coats with coloring pigmentinclusing cost of all material and labour charges etc , plumbing & carpentering , supplying , carpentering and fixing window door using first class 25mm thick mica laminated flywood board including cost of all material & necessory fittings and labour charges etc , supplying , carpentering and fixing main door with frame using pannel door and country wood frame inluding cost of all material & necessary fittings and labour charges etc , supplying and fixing pvc door including cost of all material and labour charges etc , providing and fixing indian type water closet580mm x440mm with p or s trap and necessory plumbing and tools including cost of all material and labour charges etc , providing anf fixing 1000 liter capacity pvc water tank isi brand with necessary fittings, using50mtrs lenth pvc 1 1/2 pipe from existing water point to water tank inlet and using 40mtrs lenth 3/4pvc pipe and all tap, elbow and etcnecessary tools and tackels including cost of all material and labour charges...

municipality - Tamil Nadu

33420952 15th cfc_2020_21_tied grant_ supply and delivery of earth moving equipment back hoe loader 3dx ecoxpert for solid waste management in chinnamanur municipality 15th cfc_2020_21_tied grant_ supply and delivery of earth moving equipment back hoe loader 3dx ecoxpert for solid waste management in chinnamanur municipality , supply and delivery of 3dx ecoxpert backhoe loader (with live link) fitted with 1.1 cum bucket at loader end,0.26 cum bucket with bolt on teeth at excavator end,powered by jcb engine 448 water cooled 4 cylinder diesel engine of 49 hp and with standard specification.inclusive of gst,,registration,insurance,site delivery & tools. 1.supply of backhoe loader with below mentioned pecifications 2.engine – bs iii norms, 49 hp,torque 230 nm to 240 nm, auto stop feature, water cooled diesel engine. 3.two wheel drive machine. 4.hydraulic system : variable displacement hydraulic pump with standard mode & economy mode, with hydraulic pressure range of 3800 psi to 3900 psi. 5.excavator bucket capacity : 0.24 cu.m to 0.26 cu.m 6.excavator digging depth : 4.77 7.excavator tear out force : 5700 kgf 8.excavator max working height : 5.97 m 9.led rear working lights. 10.livelink monitoring system &intelli diagnostics system. 11.edsd heavy duty loader arm 12.loader bucket capacity : 1.0cu.m to 1.1cu.m 13.loader arm breakout force : 5300 kgf 14.electricals –ip 69 dust & water proof electrical horness. 15.cabin – all round visible cabin with easy walk through access, digital cluster display with digital speedometer & trip meter ( km & hr ). 16.service intervals – engine oil 500 hrs & hydraulic oil 4000 hrs. 17.office with service and parts support in uthamapalayam taluk. 17....

Chennai Petroleum Corporation Limited - Tamil Nadu

33399551 construction of anganwadi building at tiruvottiyur under corporate environment responsibility (cer) of cpcl construction of anganwadi building at tiruvottiyur under corporate environment responsibility (cer) of cpcl , part a civil works , earth work in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means (hydraulic excavators)/manually for depth upto 1.5m,including cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, and stacking of excavated material within a lead of 100m, including providing temporary supports to existing facilities viz., service lineslikewater pipes, electric under ground cablesetc. if any all complete as per the specifications and directions of engineer in charge. , same as item no: 20 above, but for depth beyond 1.5m and upto 3.0m. , backfilling after execution of the work to the proper grade and level with selected approved available excavated soil fromsoil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in foundations, plinths, etc.all complete as per directions of engineer in charge. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the corporation/municipality designated area up to a lead of 7km including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , supplying and filling m sand of specified quality underfootings,pedestal etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layersnot exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , supplying and filling approved quarry dust of specified quality under floors, plinths, etc. for all depthsincluding the cost of quarry dust, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying in position plain cement concrete (pcc) 1:4:8 with 40mm & down size graded aggregate for levelling course/fill under footings,pedestal etc., for all depthsincluding all tools and tackles, labour and material charges, curing, compacting,in any shape, level, thickness, position and finishing the surface smooth/rough etc., complete as directed by engineer in charge. , providing&laying dry rubble soling (hard core) with 20 to 40 mm size metal, under foundations/ ground floor slab (grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of engineer in charge. , providing, mixing and laying in position rcc 1:1.5:3 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m.using 53 grade ordinary portland cement in sub structure for all depths upto ffl level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position rcc1:1.5:3 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m. using 53 grade ordinary portland cement in super structure for all heightsabove ffl level including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (excluding the cost of reinforcement, shuttering), etc. all complete as specified,and directed by engineer in charge. , providing and fixing straight / inclinedcentering and shuttering in sub structure for all depths upto ffl levelincluding strutting, bracing, propping etc. keeping the same in position during concreting and de shuttering & removal of the same after specified period as per specifications.keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , providing and fixingstraight / inclined centering and shuttering in super structure at all heights above ffl level including strutting, bracing, propping etc. keeping the same in position during concreting, de shuttering & removal of the same after specified period as per specifications etc.,keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500 for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry in sub structureup to ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for alldepthsincluding the cost of materials, labour, tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structureabove ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying half brick masonry in cement mortar 1 : 4 (1 cement : 4coarse sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing 15mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the engineer in charge. , providing 12mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrickmasonry, concrete surfacesincluding preparation of base, cleaning, chipping, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 fine sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the engineer in charge. , providingandapplying two coats of interior emulsion with wall putty of approved make of any shades/coloursover one coat of primer asper the specifications includingnecessaryscaffolding and surface preparation consisting of application of plaster of paris punning over entire surface, filling all holes and depressions with white cement, applying a coat of primer, two or more coats of oil based putty(as per manufacturers recommendations)sand paperingetc. in walls and roof ceiling, complete as per specification and as directed by engineer in charge. , providing and applyingweather proof textured exterior paint on rcc /brick walls / plastered surface etc. of asian ,nerolac,berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti fungal, water proof, anti flakingweather proof paintof approved quality and shade including painting cartoon characters/kid friendly images in the elevation as per requirement etc.this alsoincludesnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of plaster of paris punning over entire surface,filling all holes and depressions with plaster of paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturers recommendations) sand papering etc., all complete as per specification and as directed by engineer in charge. , supplying, transporting, storing, fabricating & erecting in position bolted and / or weldedstructural steel works like angles, channels, beams, plates, square/round bars, pipes, tubesfor ladders at all heights & levels and locations including all builtup sections/ compound sectionsmade out of rolled sections and / or plates / bent plates for curb edging etc., cutting to required size, straightening/bending if required, edge preparation,cleaning, scrapping & welding, preheating, finishing edges by grinding, fixing in line and level,including preparing the surface for painting,surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease etc complete along with providing paint system as follows:(a) applying inorganic zinc silicate coat 75 micron dft(b) two coats of epoxy primer paint 75 micron dft each(c) two coats of anti rust epoxy top coat paint 100 micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after grit blast cleaning in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , providing and laying of premium quality glazed/matt finish vitrified tiles of size 800x800of kajariaor approved equivalent, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles,4skirting all around as per drawing ,along with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge as per drawing. , providing and laying of premium quality antiskid ceramic tiles of size 300x300 ofapproved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge. , providingand laying coloured glazed ceramic tiles for wall/dado(grade i quality), ofapproved make & shade including 20 mm thick cementbedding c.m. 1:3, pvc beading with matching colour, pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface, all complete with material costs, tools and tackles, stagings labour charges as perspecifications and as directed by engineer in charge. , providing and fixing in position two track two panel sliding upvc windows (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing bright finished brass 100mm mortice latch and lock isi marked with four levers and a pair of polished stainless steel decorative handles(size of handles to match the door size) with necessary screws etc. complete (best make of approved quality) as specified by engineer in charge. , providing and fixing solid sheet vinyl wall paper of minimum 150gsm , embossed with textured effect pasted to wall using flake adhesive to be fixed on to the walls/partitions neatly with out shrinkage and bubbles and should have seamless joints. the design , shade and colourshall be as directed by engineer in charge. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of kutty or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side with decorative1mm thick laminate and another side with water proof laminate of archidply or approved equivalentincluding providing and fixingt type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) including providing wooden filler/sealer, stainless steel lock with status indicator, teak wood lipping, aluminium butt hinges, 3mm thick anodised(anodic coating not less than15 microns) aluminium kicking plate fixed with screws for entire door width on either side of door for a height of 600mm, fixing with door frame,door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixingsecond class teak wooden framesfor doors, windows, ventilators,cupboards etc. for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner, painting with two coats of approved shade and make (ici or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by engineer in charge. , supplying and fixing30 mm thick wpc door shutter withframe including towerbolts on either sides,handlesincluding metal hinges and all other fittingsetc. complete as per directions of engineer in charge. , providing & laying to required slope cement concrete screed of mix 1:1.5:3 (1 cement : 1.5 coarse sand: 3 coarse aggregates 12.5mm and down graded aggregates) using 53 grade opc inroof terrace etc. laid to required slope and thickness & inclusive of curing/pond curing, brooming with wire brush, finishingetc.all labours, tools and tackles complete as per drawing, specification & as directed by engineer in charge. , providing and laying water proofing membrane to roof of atactic poly propylene (app) with non woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturers specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. (the thickness of atactic poly propylene (app) membrane to be considered as 4.0mm) , providing and fixing in positionstainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onm.s. brackets, supply, fixing ofm.s.brackets, fasteners, sinkcock (quarter turn range) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipewith heavy bottle trap of parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by engineer in charge. , providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre polished machine cut granite for platformsof approved qualityfor wash basin/ vanity counters,pantry etc.of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 cement:4 m sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing & fixing white floor mounted european water closet (ewc) with dual flush cistern of parry ware petitieor approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook,bibcock andother standard accessories, all fittings and fixturesincluding cutting walls/ floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing & fixing white floor mounted kidseuropean water closet single piece suit (including closet,flushing cistern,soft close seat cover and all fittings)of parryware kids c8941 or approved equivalent make including all fittings,slim line health faucet with hose & hook, bibcock and other standard accessories, all fittings and fixturesincluding cutting walls/ floor, making good of same,making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing and fixing white glazed earthenware china kids wash basin with pedestal of make parryware make c8943 or approved equivalent of 530x290x520 mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing and fixing white glazed earthenware china wash basin of make parryware/hindware with antisplash rims on 3 sides of 550x450mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing and fixingmirror of superior glass of parryware or approved equivalent complete with cp brass screws, fastners and washers complete as directed by engineer in charge. , providing and fixing600 mm long cp rodtowel rail of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by engineer in charge. , providing and fixing c.p. brass shower rose 100mm diameter with 15 to 20mm inlet of parryware or equivalent approved including 230mm shower arm, making inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing of cp brass twin robe hook of parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with cp screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , providing and fixing15 mm nominal outer dia. & sdr11 chlorinated poly vinyl chloride(cpvc) pipes (exposed on wall) , of approved equivalent make having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. this includes jointing of pipes & fittings with one step cpvc solvent and testing of joints complete as per directions of engineer in charge. , same as sl. no: 450 above, but for 20mm nominal outer dia. pipes , same as sl. no: 450 above, but for 50mm nominal outer dia. pipes , providing and fixing 80mm dia. nominal boreunplasticised rigidpvc(upvc pipe) sch. 40 water line pipes (concealed pipeline) conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion (single socketed pipes) with necessary fittings /accessories etc.all complete as per specifications and as directed by engineer in charge. , same as sl. no. 480 above, but for 100mm dia. nominal bore pipes. , same as sl. no. 480 above, but for 150mm dia. nominal bore pipes. , providing and fixing 150 mm dia. rigid pvc rain water pipeswith ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing100 mm dia.rigidpvc pipes with pressure rating of 4 kg/ sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring jointsusing approved lubricant, making hole in the slaband restoring the same to the original condition including provision of cowl in the septic tank vent pipe etc. complete as per specifications and directions of engineer in charge. , providing and fixing two way bibcock single lever range with flange of parryware or equivalent approved 15mm nominal bore cp including fixingand connections, etc. completeas directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal bore brass bibcock including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal borebrass angle valve including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing 50 mm nominal bore gun metal gate valve (lever type) lever of approved quality including all fittings etc. complete as directed by engineer in charge. , supplying and laying custom (prefabricated) pvc floor sumps/ floor traps fabricated out of 110mm dia. 6 kg/cm2 class pvc pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix cp/pvc colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by engineer in charge. , providing, hoisting and fixing in position rcc precast elementswithreinforced cement concrete grade 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate(20mm & down size) withopc 53 grade cementfor shelves in kitchen and store room, storm water drain and septic tank cover slabs for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position, all complete (excluding cost of reinforcement) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supply and installation of cylindrical triple layer white virgin plastic storage tank of capacity 1000 litres of sintex or approved equivalent onground floor roof with lid and making necessary cutout /holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly,all complete. including, fixing, transportation to work site all complete as per drawings and directions of engineer in charge. , demolishingthe existing building in the location approx.120sq.m (taking all necessary safety precautions) for allheights and depths above plinth level including dismantling of flooring, fixtures, doors, windows, brickwork,columns,truss,purlin, structural steel items etc. all complete as directed by engineer in charge. this includes demolishing foundation including raft and underlying layers.all unserviceable material should be disposed atcorporation/municipality designated area upto a lead of 7kmas directed by the engineer in charge. all serviceable materials shall be the property of contractor. , supply of unskilled labourto carry out petty works not assessable for measurements/minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools etc. all complete as directed by engineer in charge. , supply of jcb on hire basis on all days including sundays on 8 hrs.shift including driver,assistant /fuel/oil/lubricants /all consumables etc. complete. the quoted rate should include mobilization, operator crews/driver /assistant cost,tools, tackles etc., as directed by the engineer in charge. , part b electrical works , supply and laying of pvc wires: the scope of work includes supply of following size of pvc insulated, copper conductor and laying in the existing surface / recessed, pvc / steel conduit / pvc casing and capping as required including connection in fans, switches, light fitting, sockets etc, as per the specifications of this tender and directions of engineer in charge. note: only isi marked cables shall be used. , 1.5 sq.mm , 2.5 sq.mm , 4 sq.mm , 6 sq.mm , supply and laying of pvc conduits: the scope of work includes supply and laying of following size of pvc conduit along with the accessories to be used for installation in surface/concealed as required, as per the specifications of this tender and directions of engineer in charge. note: only isi marked conduits shall be used. , upto 25 mm , earth pit: the scope of work includes supply , installation , testing and commissioning ofearth pitwith 65 mm dia 3000 mm longearth electrodes , complete wih all necessarymaterialsincludingexcavation of earth pit , fillingwith charcoaland salt, back filling , providing cement (concrete) slab for earth pits, paintingand markingof earth pit nosand connectionsincluding all labour and materialsand as per the specifications of this tender and directions of engineer in charge , earth flat / wire: the scope of work includes supply, installation and connection of following gi earthing strips along the cable trenches or cable trays or fixing to walls or structures and for connecting equipments to the plant grid including welding at joints, providing anti corrosive paint or bitumen and jute covering for welded portion, clamping and necessary hardware for connection etc., including all labour and materials, as per approved drawings, specification of this tender and direction of engineer in charge. , 40 x 6 gi earth flat , 8 swg wire for earthing , supply and installation ofswitch & sockets: the scope of work includes supply of the below mentioned switch & sockets as per the specifications of this tender and directions of engineer in charge. , supply and installation of 5/6 amps socket outlet , supply and installation of 5/6 amps switch , supply and installation of 16 amps socket with switch , wall mounted bulb holder with led lamp:the scope of work includes supply and fixing of wall mounted bulb holder along with min 15 w led lamp and other related accessories as per the directions of engineer in charge , tube light fitting: the scope of work includes supply and fixing of led l.fixt elite pride plus 18 w 6500 k1, cool daylight (cdl), decorative slim linear 4’ led batten fittings with bulb of havells catalogue or equivalent ,including civil work (if any) required for installation, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , supply and fixing of module box:supply and fixing of plastic/metal boxes of following sizes with all accessories including necesssary base frame plates/ mounting , cover plates, etc.,suitable for fixing decorative switches of type roma or equivalent make in havells/siemens/anchor/l&t , 1 or 2 module box , 4 module box , 6 module box , 8 module box , 12 module box , ceiling fan: the scope of work includes supply, installation, testing and commissioning of 1200mm sweep ceiling fan ofbajaj / crompton greaves / khaitan / usha / havells make of following sweep withceiling fan and regulator, including wiring the down rod of standard length (upto 30 cm) with 1.5 sqmm, pvc insulated, copper conductor, single core cable etc., as required,, as per the specifications of this tender and directions of engineer in charge. , supply and installation of 12 way db:the scope of work includes supplyand installation of 12 way db with 40 a mcb, 40 a rccb and 8 nos of 10 a mcb as per the specification of this tender and directions of engineer in charge. this shall be inclusive of all mcb and rccb => limited...

Corporation Of Chennai - Tamil Nadu

33315049 hiring 4 nos. of hydraulic excavator hiring 4 nos. of hydraulic excavator ( ex 200 or equivalent model ) for a period of 3 months or 720 hrs ( each ) whichever is later for perungudi dumping ground...

Corporation Of Chennai - Tamil Nadu

33315013 hiring 4 nos. of hydraulic excavator hiring 4 nos. of hydraulic excavator ( ex 200 or equivalent model ) for a period of 3 months or 720 hrs ( each ) whichever is later for kodungaiyur dumping ground...

municipality - Tamil Nadu

33198462 mannargudi municipality supply and delivery of backhoe loader jcb ( 1 no ) , supply of backhoe loader with below mentioned specifications: 1. engine – cev stage iv norms, crdi, 74 hp to 95 hp, turbo charged, torque 395 nm to 410 nm, 1990 bar to 2010 bar high pressure fuel injection system, auto idle & auto stop feature, water cooled diesel engine. 2. hydraulic system : variable displacement hydraulic pump with standard mode, plus mode, loading mode &roading mode operating system with hydraulic pressure range of 3900 psi to 4000 psi. 3. excavator bucket capacity : 0.26 cum to 0.3 cum 4. excavator digging depth : 4.7 m to 5.0 m 5. excavator tear out force : 5900 kgf to 6000 kgf 6. excavator max working height : 5.95 m to 6.1 m 7. led rear working lights. 8. livelink monitoring system &intelli diagnostics system. 9. edsd heavy duty loader arm 10. loader bucket capacity : 1.1 cum to 1.2 cum 11. loader arm breakout force : 5600 kgf to 5700 kgf 12. electricals – ip 69 dust & water proof electrical horness. 13. cabin – all round visible cabin with easy walk through access, digital cluster display with digital speedometer & trip meter ( km & hr ) . 14. service intervals – engine oil 500 hrs & hydraulic oil 4000 hrs. price inclusive of one year warranty, gst, insurance, registration, transportation and other charges till delivery at mannargudy municipal office...

Ministry Of Coal - Tamil Nadu

33170962 bids are invited for sm461570089 b type teeth for 700 litres capacity bucket wheel excavator. (q3) , sm461570092 e type teeth for 700 litres capacity bucket wheelexcavator. (q3) total quantity : 580...

Tamil Nadu Minerals Limited - Tamil Nadu

33117154 labour contract along with excavator and compressor with chiseling tools labour contract along with excavator and compressor with chiseling tools as stated below in sl.no.1 of the tender document....

Ministry Of Coal - Tamil Nadu

33046993 bids are invited for sm461570090 c type teeth for 700 litres capacity bucket wheel excavator (q3) , sm461570091 d type teeth for 700 litres capacity bucket wheelexcavator (q3) total quantity : 660...

Chennai Petroleum Corporation Limited - Tamil Nadu

32941233 construction of storm water drain in manali refinery of cpcl construction of storm water drain in manali refinery of cpcl , cutting & clearing the areaof grass,rank,vegetation,wild growth bushes,trees and plants upto 30cm girth measured at a height 1.0m above ground leveletc, including removal of rubbish, grass, plants, bushes, by cutting it, removing completely as per directions of engineer in charge and collecting all cut grass, vegetation etc and disposing it atdesignated place within a lead of 100m, with all tools, labour etc. complete as per specifications and directions of engineer in charge. , earthwork in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means(hydraulic excavators) / manually for depth upto 1.5m,including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated/sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes,sewage pipes, electricunderground cables, etc.all complete as per the specifications and directions of engineer in charge. , sameassl. no. 20 abovebutfor depths beyond 1.5m upto 3.0m. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the designated area outside the refinery premises up to a lead of 7km (vaikkadu village) including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , backfilling after execution of the work toproper grade and level with selected materials from available excavated soil fromsoil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm,watering, rolling and ramming by manual methods/mechanical compactors , dressing, trimming etc. in foundations, plinths,pits etc.all complete as per directions of engineer in charge. , supplying and filling approved m sand of specified quality under floors, plinths, foundations etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying plain cement concrete (pcc)1:4:8 by volume(1cement : 4 m sand:8 coarse aggregate) with opc 53 grade and 40mm & down size graded crushed stone aggregates for all depths wherever required like in foundations, fillings ,floors,pavements & ramps or any other works etc., including shuttering, tamping, ramming, vibrating, curing, etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete including cement cost etc, all complete as directed by engineer in charge. , providing, mixing and laying in position rcc 1:1.5:3 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m.using 53 grade ordinary portland cement in sub structure for all depths upto ffl level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , providing,fixing formwork including centering, shuttering ,strutting and propping in sub structure at all depths wherever required including removal of the shuttering after the specified period is over and as directed by the engineer in charge complete with all materials, labour, consumables etc.(form work shall be supplied by the contractor and shall remain the property of the contractor) , providing, hoisting and fixing in position rcc precast elementswithreinforced cement concrete grade 1:1.5:3 (1 cement:1.5 m sand: 3 graded stone aggregate withopc 53 grade,minimum cement content of 400kg/cu.m and 20mm & down size graded crushed stone aggregates)for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position using crane, breaking brickwork and /or concrete surfaces and making good the same etc. all complete (excluding cost of reinforcement) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement(conforming to is 1786, grade fe500) for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, welding spacers, lifting hooks etc for all heights & depths etc. removing of scraps from site, all complete as directed by engineer in charge. , providing and laying reinforced np3 class (medium duty) rcc hume pipe of 300mm dia. with collars jointed with stiff mixture of cement mortar in the proportion of 1:2(1cement: 2m sand)for road crossing etc.including cutting, lowering, laying in position, with proper level, slope , testing of joints etc. as per specifications and directed by engineer in charge. , demolishing pcc work (taking all necessary safety precautions)manually / by mechanical means for all depths and heights belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishing rcc work (taking all necessary safety precautions)manually / by mechanical means for all depth and height belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , supply of unskilledlabourto carry out petty works not assessable for measurements/minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools. => limited...

municipality - Tamil Nadu

32874680 supply and delivery of earth moving equipment back hoe loader ( jcb 3dx plus ) for solid waste management in gudalur municipality , supply and delivery of ( jcb ) 3dx plus backhoe loader ( with live link ) fitted with 1.1 cum bucket at loader end, 0.26 cum bucket with bolt on teeth at excavator end, powered by jcb engine 444 water cooled 4 cylinder diesel engine of 74 hp and with standard specification.inclusive of gst, , registration, insurance, site delivery & tools....

Chennai Petroleum Corporation Limited - Tamil Nadu

32849887 rate contract for projects related civil works at manali refinery of cpcl rate contract for projects related civil works at manali refinery of cpcl , cutting & clearing the areaof grass,rank,vegetation,wild growth bushes,trees and plants upto 30cm girth measured at a height 1.0m above ground leveletc, including removal of rubbish, grass, plants, bushes, by cutting it, removing completely as per directions of engineer in charge and collecting all cut grass, vegetation etc and disposing it atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village) with all tools, labour etc. complete as per specfications and directions of engineer in charge. , cutting trees of girth above 30 cm upto & including 60cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village )as per specifications and as directed by the engineer in charge. , cutting trees of girth above 60 cm upto & including 120cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises(vaikkadu village )as per specifications and as directed by the engineer in charge. , cutting treesofgirth above 120cm upto & including 240cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal ofmaterial atdesignated place upto 7 km lead outside the refinery premises in vaikkadu area as per specifications and as directed by the engineer in charge. , cutting treesofgirth above 240cm (measured at a height of 1m above ground level) including cutting of trunks and branches removing the roots up to min 1.5m depth from the ground level, with all labour, tools & tackles, etc. completeand disposal ofmaterial atdesignated place upto 7 km lead outside the refinery premises in vaikkadu area as per specifications and as directed by the engineer in charge. , earthwork in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means(hydraulic excavators) / manually for depth upto 1.5m,including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated/sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes,sewage pipes, electricunderground cables, etc.all complete as per the specifications and directions of engineer in charge. , sameassl. no. 60 abovebutfor depths beyond 1.5m upto 3.0m. , excavating trial pits manually of required size & depth upto 3m at locations as specified with necessary shoring, dewatering & backfillingas required, etc. complete as per specifications and as directed by engineer in charge. , backfilling after execution of the work toproper grade and level with selected materials from available excavated soil fromsoil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm,watering, rolling and ramming by manual methods/mechanical compactors , dressing, trimming etc. in foundations, plinths,pits etc.all complete as per directions of engineer in charge. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the designated area outside the refinery premises up to a lead of 7km (vaikkadu village) including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) todesignated areas within the refinery premises including etp/ttp areasup to a lead of 3kmincluding re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , supplying and filling approved quarry dust of specified quality under floors, plinths,etc. for all depthsincluding the cost of quarry dust, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , collection of scrap (metal/steel scrap) from anywhere within the refinery premises including supply of necessary vehicles with driver,required labour,loading and unloading etc.and handing over the materials to scrap yard within the refinery premises with all tools and tackles,manpower etc.all compelte as directed by engineer in charge. , supplying and filling approved m sand of specified quality under floors, plinths, foundations etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying plain cement concrete (pcc)1:4:8 by volume(1cement : 4 m sand:8 coarse aggregate) with opc 53 grade and 40mm & down size graded crushed stone aggregates for all depths wherever required like in foundations, fillings ,floors,pavements & ramps or any other works etc., including shuttering, tamping, ramming, vibrating, curing, etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete including cement cost etc, all complete as directed by engineer in charge. , same as sl.no: 150 above,but for plain cement concrete (pcc)1:1.5:3 , providing and laying of reinforced cement concrete (rcc) 1:1.5:3 by volume (1cement: 1.5 m sand:3 aggregate) with opc 53 grade and 20mm and down size graded crushed stone aggregate materials for sub structure upto plinth beam levelfor all depths including pavement, machine mixing, curing, consolidating with vibrator, cement cost etcall complete as per instructions of engineer in charge excluding cost of shuttering and reinforcement. , same as sl.no: 170 above,but for super structure at all heights above plinth beam level. , providing,fixing formwork including centering, shuttering ,strutting and propping in sub structure at all depths wherever required including removal of the shuttering after the specified period is over and as directed by the engineer in charge complete with all materials, labour, consumables etc.(form work shall be supplied by the contractor and shall remain the property of the contractor) , providing, fixing formworkincluding centering, shuttering ,strutting and propping insuper structure at all heightswherever required including removal of the shuttering after the specified period is over and as directed by the engineer in charge complete with all materials, labour, consumables etc.(form work shall be supplied by the contractor and shall remain the property of the contractor) , providing, hoisting and fixing in position rcc precast elementswithreinforced cement concrete grade 1:1.5:3 (1 cement:1.5 m sand: 3 graded stone aggregate withwith opc 53 grade and 20mm & down size graded crushed stone aggregates)for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position using crane, breaking brickwork and /or concrete surfaces and making good the same etc. all complete (excluding cost of reinforcement) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement(conforming to is 1786, grade fe500) for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, welding spacers, lifting hooks etc for all heights & depths etc. removing of scraps from site, all complete as directed by engineer in charge. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases etc.using non shrink grout of approved make equivalent including supply of material,roughening surface, cleaning with compressed air/water jets, ramming, curing,labour charges etc.all complete as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion joint filler boards conforming to is:1838 p1/1983 in joints including application of primer as directed by engineer in charge. , providing & filling in joints bitumastic sealing compound 12 to 17mm width x 20 to 25 mm depthofapprovedmake conforming to is:1834 latest revision grade a including one coat of primer as per manufacturer’s specifications, drawings & as directed by engineer in charge. , providing and laying coping block with cement concrete 1:2:4with 12.5mm & down size graded crushed stone chip aggregates on top of masonry wall including providing pockets, openings, recesses, chamfering wherever required, tamping, curing and rendering if required to give a smooth and even surface etc. for all heights in any shape, profile, position and thickness etc. all complete as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks ofclass 5.0 in cement mortar 1:5 (1 cement:5 m sand)for all depths including the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level , curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in using cement mortar 1:5 (1 cement:5 m sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam/slab, embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying half brick masonry in cement mortar 1 : 4 (1 cement : 4m sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing random rubble masonry with hard stone in sub structure with cement mortar 1:6 (1cement:6 m sand) for toe wall , including the cement cost , tools & tackles, labour required to complete the job, rendering the full face with 1:3 cm as per the specifications and directions of engineer in charge. , same as item no:300 above ,but for superstructure. , providing&laying dry rubble soling (hard core) with 20 to 40 mm size metal, under foundations/ ground floor slab (grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of engineer in charge. , providing 15mm thick cement plasterin cement mortar 1:4(1 cement:4 m sand by volume) onbrickmasonry, pcc/rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster,bands ,mouldings etc. as specifiedfor all depths and heights including labour charges,tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 12mm thick cement plasterin cement mortar 1:4 (1cement:4 m sand by volume) onbrickmasonry,pcc/rcc surfacesincluding preparation of base, cleaning, chipping ,packing of electrical,plumbing works ,scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster,bands ,mouldings etc. as specifiedfor all heights including labour charges,tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 fine sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the engineer in charge. , providingandapplying two coats ofinterior paint of interior emulsion paint with wall putty of birla white/jk white or any other approved equivalent make of any shades/coloursover one coat of emulsion primer asper the specifications includingnecessaryscaffolding and surface preparation, filling all holes, cracks and depressions with wall putty,sand paperingetc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of exterior emulsion paint of asian or any other equivalent approved brand of required shade and includingsurface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty of birla white/jk white or any other approved equivalent make, necessary scaffolding etc, etc all complete as per specifications and directions of engineer in charge. , providing and applying 3 coats of white wash of approved make and shade for all depths and heights including cleaning, preparation of surfaces, curing etc with all labours, tools, tackles, scafolding etc. complete as directed by engineer in charge and as per specifications. , providing and applying two coats of water proof decorative cement paint of approved make and approved shade, cleaning, including preparation of surfaces, priming coat with cement primer,curing etc. all complete as per directions of engineer in charge. , providing recessed pointing onrandom rubble masonrywall for all heights with cement mortar 1:3(1cement:3 m sand) including scaffolding/staging, finishing, curing, etc.allcomplete as specified and directed by engineer in charge. , providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre polishedgranite for platformsof approved qualityfor shelves of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 cement:4 msand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish,curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing and fixing 20mm thick machine cut,polished cudappah slab of approved qualityfor kitchen sinks of required size of approved shade, colour, and texture jointed with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, for fixing as kitchen sink, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing and laying vitrified floor tiles of 600mmx 600mmof stain guard1st class quality ofapproved makelaid on 20mm thick cement mortar 1:4 (1 cement:4 m sand) , including a coating of adhesive as per manufacturers specifications, flush pointing of joints of tiles with cement paste, grouting with white cement and pigment with colour matching the shades of tiles including skirting, finishing ,curing ,material costs,labour charges,tools and tackles etc. all complete as directed by engineer in charge. , providing and laying of premium quality antiskid ceramic floor tiles (size of all tiles shall be 300x300) ofapproved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles,labour charges etc.as per specifications, standards and instructions of engineer in charge. , providingand laying upto300 x 450 mm size coloured glazed ceramic tiles for wall/dado(grade i quality), of approved make & shade including 20 mm thick cementbedding c.m. 1:3, pvc beading with matching colour , pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface with wax polishing complete with material costs,tools and tackles,labour charges as perspecifications and as directed by engineer in charge. , providing and laying pvc roll/tile of approved shade,texture of 2mm thickness homogenous, unbaked,flexible,anti static pvc tiles conforming to bs 2050 table 2, is 3461/3462 in floor,skirting,fixed over base floor/surface by means of a continous coating of rubber adhesive ( as per manufacturer specification) overthe base floor/surface including cleaning the finished surface with approved detergent to remove stains etc. all compelte as directed by engineer in charge.removal of damaged existing membrane to be carried out if required. , providing & forming40mm thick average hard wearing surface with granolithic concrete floor finish (1:1:2) laid in 2.5 m x 2.5 m panels by means of necessary formwork over concrete floor includingmaterials,labour,tools,tackles etc. all complete as per specification, drawings & as directed by engineer in charge. , providing asbestos free everest hitech or equivalent6mm thick corrugated cement sheet roofing in natural stone grey colour and fixing with high corrosion resistant self drilling fasteners and epdm washers by replacing the existing worn out sheet etc. complete ; including cutting to size and shape ,providing laps,scaffolding etc.with all labour,tools as directed by engineer in charge. , providing asbestos free everest hitech or equivalentserrated adjustable ridges for roofing including fixing with accessories like high corrosion resistant self drilling fasteners/epdm washers and or g.i. seam bolts and nuts, g.i. plain and bitumen/ washers including cutting to proper size , scaffolding, etc., for all heights with all labour,tools & tackles complete as directed by engineer in charge. , providing asbestos free everest hitech or equivalentgutterof 600mm overall girth semicircular in shape for roofing including fixing with necessary slope with accessories likegutter guards, clamps,brackets,high corrosion resistant self drilling fasteners/epdm washers and or g.i. seam bolts and nuts, g.i. plain and bitumen/ washers including cutting to proper size , scaffolding,providing provision for fixing rain water downtake pipe etc., for all heights with all labour,tools & tackles complete as directed by engineer in charge. , supplying, transporting, fabricating, erecting and fixing in position colour coated corrugated galvalume sheet of 0.45mm base metal thickness , with colour coating including fixtures, bitumen washers, corner pieces, all necessary accessories, scaffolding etc. complete in all respects at all levels, locations and as perspecifications and direction of engineer in charge. , providing & laying to required slope cement concrete screed of mix 1:1.5:3 (1 cement : 1.5 m sand: 3 coarse aggregates 12.5mm and down graded aggregates) using 53 grade opc inroof terrace etc. laid to required slope and thickness & inclusive of curing/pond curing, brooming with wire brush, finishingetc.all labours, tools and tackles complete as per drawing, specification & as directed by engineer in charge. , providing and laying cool roof s.r.i (solar reflective index)tiles of johnson endura or approved equivalent ,size 300mmx300mm ,white in colour with thickness not less than 10mm, on terraces jointed with suitable cementious water proof grout, laid over suitable tile fixing mortar as per manufacturers specification with required slope, thickness and finishing neat including pointing etc. complete with all tools, tackles, equipments, labour, cement cost etc. as per specifications and as directed by engineer in charge. , providing and laying first quality pressed clay tiles( as per approved pattern not less than 18 mm thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement: 4 msand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement: 4 m sand) and finishing neat including all tools, tackles, equipments, labour,materials,hacking of concrete,necessary surface preparation,pointing with cement mortar 1:4 mixed with 2 % integral water proofing compound , etc.whereever required , complete as per specifications and as directed by engineer in charge. , providing and fixing white glazed earthenware china wash basin of make parryware/hindware with antisplash rims on 3 sides of 550x450mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing & fixing white glazed earthernware indian pan type water closetof parry ware orrissa or approved equivalent of size 580x440 mm with integral footrest,includingall fittings, p or s traps, cutting walls, floors making good of same, finishing, soldered joints, making inlet/outlet connection, providing min. 150 mm thick sand cushion, finishing, etc.all complete as directed by engineer in charge. , providing & fixing white wall hungeuropean water closet (ewc) with dual flush cistern of parry ware or approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook, other standard accessories, all fittings and fixturesincluding cutting walls, floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing & fixing white floor mounted european water closet (ewc) with dual flush cistern of parry ware petitieor approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook,bibcock andother standard accessories, all fittings and fixturesincluding cutting walls, floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing and fixing white glazed earthern ware half stall urinal of parry ware niagara orapprovedequivalent, including parryware brand or approved equivalent cp urinal push angle valve, cp brass spreader with 32 mm dia pvc pipe, tee, distribution pipe, brackets etc. making inlet & outlet connections fixing with cp brass screws, finishing, etc. all complete as directed by engineer in charge. , providingandfixing in position white glazed earthern ware vitreous chinadivisional platepartition for urinals of size 350x675x130mmparryware magnum or approved equivalent placedbetweenurinalsanchoring and fixing the divisional plate with fastners and required clamps / fittings, making good of all damaged work, finishing etc., all complete as per specification and as directed by engineer in charge. , providing and fixing20 mm nominal outer dia.sch 40 unplasticised poly vinyl chloride(upvc) pipes, of approved equivalent make with ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb,spacing of jumpers shall be minimum 1mc/c etc. all complete including jointing with bonding solution of approved quality and makeincluding clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , same as sl. no: 610 above, but for 25mm nominal outer dia. pipes , same as sl. no: 610 above, but for 50mm nominal outer dia. pipes , providing and fixing 15 mm dia. nominal bore galvanized iron (gi) pipes complete with gi fittings including trenching and refilling etc. (external work) complete as per directions of engineer in charge. , same as sl. no. 640 above, but for 20mm dia. nominal bore pipes. , same as sl. no: 640 above, but for 50mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 80mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 100mm dia. nominal bore pipes. , same as sl. no. 640 above, but for 150mm dia. nominal bore pipes. , providing and fixing75 mm outer dia. of 6kg/sq.cm poly vinyl chloride(pvc) pipes (exposed on wall) ,including all pvc plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. this includes jointing of pipes & fittings with one step pvc solvent and testing of joints complete as per directions of engineer in charge. , same as item no:700 above, but for 110mmouter diameter. , providing and fixing 160 mm dia. rigid pvcpipesas rain water pipes,weep hole pipes etc. with ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal borebrass angle valveincluding breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixingapproved cp brass urinal push angle valve of parryware or approved equivalent including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing metro or equivalent approved 15mm nominal bore brass bibcockincluding breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing two way bibcock single lever range with flange of parryware crust or equivalent approved 15mm nominal bore cp including fixingand connections, etc. completeas directed by engineer in charge. , providing and fixing 25 mm nominal bore gun metal gate valve with cast iron (ci) wheel of approved quality (screwed end) including all fittings etc. complete as directed by engineer in charge. , same as sl. no. 770 above, but for 40mm nominal bore gate valve , same as sl. no. 770 above, but for 50mmnominal gate valve , providing and fixing 25mm nominal bore gi union in existing gi pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required as directed by engineer in charge. , same as sl. no.: 800 above, but for 40mm nominal bore gi union. , same as sl. no.: 800 above, but for 50mm nominal bore gi union. , providing and fixing 600 x 450mm mirror of superior glass of parryware or approved equivalent complete with cp brass screws, fastners and washers complete as directed by engineer in charge. , providing and fixing600 mm long cp rodtowel rail of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by engineer in charge. , providing and fixing in position approved quality liquid soap dispenser ofparrywareor approved equivalent make, of standard size with snap fittings, including drilling holes, fixing with cp screws all complete as directed by engineer in charge. , providing and fixing c.p. brass shower rose 100mm diameter with 15 to 20mm inlet of parryware or equivalent approved including 230mm shower arm, making inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing of cp brass twin robe hook of parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with cp screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , providing and fixing in positionstainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onm.s. brackets, supply, fixing ofm.s.brackets, fasteners, sinkcock (quarter turn range) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipewith heavy bottle trap of parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by engineer in charge. , providing and fixing coloured 10 litre p.v.c low level flushing cistern with manually controlled device(handle lever) deluxe dual flushofparryware or approved equivalent make with all fittings and fixtures complete as directed by engineer in charge. , supplying and laying in position square shaped 600mm x600 mm(grade md 10) medium dutyci manhole frame with lugs and coverincluding breaking of brick masonry or concrete surface to receive frame with lugs and making good the same with cement mortar 1:3 including applying two coats of anticorrosive paint inclusive of all labours and materials etc. complete as per specifications and as directed by the engineer in charge. , supplying and laying custom (prefabricated) pvc floor sumps/ floor traps fabricated out of 110mm dia. 6 kg/cm2 class pvc pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix cp/pvc colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by engineer in charge. , making connection of drain or sewer line using pipes of upto 230mm diameter with existing manhole including breaking into and make good the walls, floors with cement concrete 1 : 2 : 4 mix (1 cement : 2 m sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1 : 4 ( 1 cement : 4 m sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. completeas directed by engineer in charge. , providing and fixing window/ventilator/ door glass panes with float glass panes with float glass of thickness 4mm, fixing with necessary pins and best quality putty or with wooden batten as necessary including removing old damaged glass, disposing of the same as directed all labour and materials etc. complete at all heights as directed by engineer in charge. , providing and fixingaluminium extruded section body tubular type universal hydraulic door closer of everest/ dyna/ universal or any other equivalent approved make with double speed adjustment with necessaryaccessories and screws with all labour charges,tools & tackles etc. all completeas directed by engineer in charge. , providing and fixing double action hydraulic floor spring with stainless steel cover plate of minimum 1.25mm thicknessof universal, everest or any other equivalent approved brand and manufacture is: 6315 marked, for doors for all heights includingall labours, tools and tackles ;cost of cutting floors as required, embedding in floors and cover plates with brass pivots and single piece m.s. sheet outer box with slide plateetc. complete as per the directions of engineer in charge. , providing and fixing bright finished brass 100mm mortice latch and lock isi marked with four leverswith necessary screws etc. complete (best make of approved quality) as specified by engineer in charge. , providing and fixing bright finished 125mm brass handles with necessary screws drilling holes in doors, cup boards including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , same as sl. no.: 970 above, but for 75mm brass handles. , providing and fixing in position first quality non reflective type polyester sun control film ofgarware or equivalent approved make of25 micron thickness including cleaning the door/ventilator panes,trimming the edges etc. complete as per the instructions of engineer in charge. , providing and fixing 12mm thick prelaminated particle board with decorative lamination on one side and balancing lamination on other side; flat pressed three layer or graded wood particle board, in panelling fixed in aluminium doors, windows ,shutters and partition frames with chromium platted(cp) brass / stainless steel screws etc. complete as perdirections of engineer in charge. , supplying and fixing24 mm thick pvc panelled door shutter with pvc frame including pvc towerbolts on either sides, pvc handlesincluding metal hinges and all other fittingsetc. complete as per directions of engineer in charge. , providing and fixing anodised aluminium work for fixed portion of doors, windows, ventilators and partitions with extruded built up standard tubular sections/approximate z sections and other sections of approved make, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required pvc/neoprene felt etc. for fixed portion, minimum anodic coating of grade ac 15 shall be provided.aluminium sections shall be smooth, rust free, straight, mitred and jointed mechnically whereever required including cleat angle, aluminium snap beading for glazing/panelling, c.p. brass/stainless steel screws, all complete as per directions of engineer in charge. (glazings and panellings shall be paid separately) , same as sl.no: 1020 above, but for shutters of doors, windows, ventilators including fittings. , providing and fixing in positionupvc doors both single leaf/double leaf white in colour comprising of glass panel minimum 5mm thick and upvc panels of minimum 15mm thickness (doors may be either partly glazed partly paneled or fully panelled)with upvc stiles, rails,frame and accessories holdfasts, hinges, pull handles on both sides, locking arrangement as per requirementincluding labour charges, material cost, tools and tackles all complete as per specifications & as directed by engineer in charge. , providing and fixing in position sliding upvc windows/ventilators (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , designing,supplying and fixing in position approved make chain/gear opearted steel rolling shutters conforming to is : 6248 using 18 gauge ms interlocking laths sections formed out of cold rolled steel strips 0.9mm thick,18mm wide and 1.25mm thick,80mm wide respectively for shutter width upto 3.5m and above 3.5m ; jointless ms channel section for guide ( minimum 3.15mm thick) ms girders,pressed bottom rails,shutter suspension stud shaft with pulley andcage,top rolling springs, locking arrangement including hood,gear operating mechanism and all accessories required and providing two coats of approved make and shade of rust proof synthetic enamel paint over a coat of red oxide or zinc chromate rich primer, etc. all complete as per directions of engineer in charge. , providing and fixing in position single/double leaf hinged type fire proof doorsof radiant or approved equivalent make conforming to is: 3614 with all necessary fittings and fixtures etc. fire proof doors shall have minimum fire rating of 2 hours including 1.20 mm thick stainless steel sheet cladded 46mm thick shutter with infill material honeycomb board complete with stainless steel frame (double rivet – 143 x 57mm) made from 1.60mm thick stainless steel sheet & fixing arrangementsetc. all complete as directed by engineer in charge. stainless steel shall be of grade 304. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of kutty or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side with decorative1mm thick laminate and another side with water proof laminate of archidply or approved equivalentincluding providing and fixingt type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) including providing wooden filler/sealer, stainless steel lock with status indicator, teak wood lipping, aluminium butt hinges, 3mm thick anodised(anodic coating not less than15 microns) aluminium kicking plate fixed with screws for entire door width on either side of door for a height of 600mm, fixing with door frame,door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixingsecond class teak wooden framesfor doors, windows, ventilators for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner, painting with two coats of approved shade and make(ici or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by engineer in charge. , false ceiling(a): providing and fixing in position 12 mm thick exterior grade boiling water proof(bwp) both sides prelaminated particle board (novapan or equivalent approved make) panels of approved colour and texture to form grids of 600x600 mm and suspension system consisting of aluminium framework with (a) main runners aluminium tee sections of 25mmx35mmsize,1.5mm thickness(b)cross runners aluminium tee sections of 25mmx25mm size,1.5mm thickness(c) perimeter section aluminium angle section 38mmx38mm,1mm thickness all round the perimeter of the ceiling.the grid system is to be suspended by interlocking the main and cross runners @ 600mm max.bothways by means of aluminium angle cleats.the main runners shall be suspended from the ceiling by means of 3mm thick ms flat clamp fixed to main runners @ 1200 max.and fixed to 6mm dia ms hook which again is fixed to ceiling.3mm thick ms flat clamp shall be connected to main runners with 25mm long ms clamp with levelling nut and @ 1200 mm max. the ms hooks shall be suspended from ceiling by means of slotting in 25mmx25mmx3mm thick ms angle,fixed to the slab by 12mm dia. dash fasteners@1200mm c/c.cross runners shall be fixed suitably @max.600mmc/c to form a grid 0f 600mmx600mm.necessary provisions for suspendinglight fixtures etc.,wherever necessary shall be provided .the framework may be suspended from the roof slab at desired height including finishing,making the framework perfectly levelled and aligned etc. all complete as per directions of engineer in charge.all the suspended members shall be anodized(min.15 microns) aluminium frames of standard extrusions .the rate quoted shall include the material costs,labour charges,tools and tackles etc. , false ceiling(b): providing and fixing false ceiling using aluminium composite panel acp 4mm thick (0.5mm thick aluminium sheet on top & bottom sandwiched with 3mm thick core material )confirming to bs 1467 in combination with approved solid and metallic colour panels laminated sandwiched composite panels to a grid made out of anodized aluminium (with 15 micron anodic coating) t sections 35x15x1.5mm size main runners and cross runners 23.5x19x1.5mm fixed to main runners placed 600mm centre to centre both ways so as to form a grid 600mm square.the frameowrk shall be suspended from the ceiling by level adjusting hangers of 6mm dia ms rodfixed to roof slab by means of ceiling cleats.the suspender shall be placed 600x1200 mm centre to centre including fixing to the frame with cp brass screws and applying priming coat of zinc chromate yellow primer.rates are inclusive of scaffolding,frame work ,labour charges,tools and tackles,all material costs etc. complete as directed by engineer in charge. , demolishing pcc work (taking all necessary safety precautions)manually / by mechanical means for all depths and heights belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishing rcc work (taking all necessary safety precautions)manually / by mechanical means for all depth and height belowand above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable materialatdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishingbrick masonry incement mortar (taking all necessary safety precautions) for allheightsabove plinth level including supply of all labours,tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material atdesignated place upto 7 km lead outside the refinery premises (vaikkadu village) as per specification and directions of engineer in charge. , demolishingstone/rubble masonry (taking all necessary safety precautions) for demolition of existing compound wall for the entire heightabove ground level including supply of all labours,tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable materialatdesignated place upto 7 km leadin vaikkadu area as per specification and directions of engineer in charge. , dismantling of structural steel works (bolted/riveted/welded)of all descriptions(taking all necessary safety precautions) for all heights & depths above & belowplinth level including supply ofall tools & tackles, consumables, necessary scaffolding etc. providing temporary bracings as required, cutting gussetplates, bolts, nuts, weldings etc, stacking of serviceable materials at designated location /cpcl storage yard/scrap yardwithin the refinery premises as per direction of engineer in charge. , dismantling and stacking fencing fabric of any material (taking all necessary safety precautions) , including supply of all tools & tackles, necessarypropping, underpinning, cutting, transporting , stackingand handing over the material to cpcl scrap yard inside refinery etc. all complete as specified and directed by engineer in charge. , dismantling bituminous road(taking all necessary safety precautions)manually / by mechanical means for all depths including cutting road taking out soling and metalling,sorting and screening,supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and stacking of serviceable material, disposal of unserviceable materialto spoil heaps within 50mlead all complete as specified and as per directions of engineer in charge . , dismantling ci ,gi,pvc or asbestos drainage pipe with fitting and clamps including scaffolding, staging working platforms all complete including supply of all tools & tackles,stacking material, transporting, loading & unloading and handing overto scrap yard/stores within refinery premises and disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area) as specified and directed by the engineer in charge. , dismantling of water closet, urinals, wash basins & flushing cistern of all types (ci, pvc, viterous china) with fitting and clamps including pipe lines all complete including supply of all tools & tackles,stacking material, transporting, loading & unloading and handing overto scrap yard/stores within refinery premisesand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area) as specified and directed by the engineer in charge. , demolishing of aluminium partitions/ gypsum/pop/tiled/thermocol false ceiling ,doors, windows, ventilators (steel/wood/aluminium/glass)shutters including, chowkhats, frames, architrave, holdfasts and all other retrieved materials(taking all necessary safety precautions) for all heights above floor level including supply of all labours,tools & tackles, providing necessary scaffolding, propping, underpinning, temporary supports etc.,as per the instruction of engineer in charge, cleaning and stacking of serviceable material like aluminium frames at destined location /cpcl storage yardwithin the refinery area and disposal of unserviceable material atdesignated place(vaikkadu area) upto 7 km lead outside the refinery premises as per specification and directions of engineer in charge. , demolishing of tile work in floors & walls laid in cement mortar for thickness upto 25mm (taking all necessary safety precautions)manually / by mechanical means including supply of all tools and tackles, propping, underpinning, cleaning the siteand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area)as per specification and directions of engineer in charge. , dismantling of tile work in roofing for thickness upto 25mm (taking all necessary safety precautions)manually / by mechanical means including supply of all tools and tackles, propping, underpinning, cleaning the siteand disposal of unserviceable materialatdesignated place upto7 km lead outside the refinery premises (vaikkadu area)as per specification and directions of engineer in charge. , dismantling ofgi/ac/aluminiumroofing sheets including ridges, hips, gutters, etc.in roofing, including suppy of all labours,tools & hooks, transportation and stacking of serviceable materials at destined location /cpcl storage yardwithin the refinery area and disposal of unserviceable material atdesignated place(vaikkadu area) upto 7 km lead outside the refinery premises as per specification and directions of engineer in charge. , chippingof rcc work by chisellingfor all depths below plinth level including supply of all tools and tackles,scaffolding,propping,underpinning etc. exposing, cutting,lapping/welding the reinforcement bars as per drawings and cleaning the same by wire brushing, washing the exposed surfaces,disposal of the unserviceable material to spil heaps anywhere within the plant boundary all complete as specified and directed.(excavation and backfilling if any shall be paid separately under relevant items.) , supplying,handling,transporting to site of work and fixing approved mechanical anchor fastenersms boltsof grade 5.8 or more,galvanisedwith minimum thickness of 5 microns(approved for use in cracked concrete),of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed by engineer in charge. , same as item 1260 above, but for 16mm dia. , same as item 1260 above, but for 20mm dia. , supplying,handling,transporting to site of work and fixing approved chemical anchor fasteners consisting of ms threaded rod of grade 5.8,galvanisedwith minimum thickness of 5 microns and chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors,roofs,beams( sides and bottom), walls,columns etc. according to manufacturers specifications including all accessories like nuts,washers etc. of required size,testing,necessary scaffolding,drilling of the holes in concrete surface with electric drill,cleaning of holes with air blowout & wire brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed by engineer in charge. , same as item 1290 above, but for 16mm dia. , same as item 1290 above, but for 20mm dia. , making pockets/holes of sizes upto & inclusive 200x200x500mm in rcc/pcc works(taking all necessary safety precautions) by chiselling/drilling, including supply of all tools and tacklesetc. cutting of reinforcement bars,cleaning the pockets of all debris etc. all complete at all heights & depths as specified and directed by engineer in charge.scaffolding and disposal of debris shall be paid separately under relevant items. , repairs to existing rcc beams & columns, including chipping and dismantling & removing of loose particles applying cement paste, raking out joints, applying epoxy resin for bonding fresh cocrete to old concerete, filling void portionwith concrete 1:1:5:3 concrete (1cement:1.5 m sand :3 stone agrregates 12mm size) making good as same, including formwork, curing, staging, working platforms labours, tool and tackles all complete as per specifications and directions of engineer in charge. , supplying, transporting, storing, fabricating & erecting in position bolted and / or weldedstructural steel works like angles,channels, beams, plates, pipes, tubes etc.at all heights & levels and locations including all builtup sections/ compound sectionsmade out of rolled sections and / or plates / bent plates inexisting / new structural pipe supports, frames, etc., cutting to required size, straightening/bending if required, edge preparation,cleaning, scrapping & welding ofunsoundjoints in existing structural members, preheating, (including sealing of box section with continuous welding ) finishing edges by grinding , fixing in line and level with temporary bracings,including providing staging, scaffoldings, & working platforms at all heights, and removal of same after erection,including preparing the surface for painting ,surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease etc complete along with providing paint system as follows:(a) applying inorganic zinc silicate coat 50 micron dft(b) two coats of epoxy primer paint 50 micron dft each(c) two coats of anti rust epoxy top coat paint 75 micron dft each as per manufacturers specifications and as directed by engineer in charge. (d) note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after manual cleaningprior to erection as per specifications & as directed by engineer in charge. supply of all materials in contractors scope. , same as sl. no. 1340 above, but for supplying, transporting, storing, fabricating & erecting in position structural steel works alone, excluding painting works but including pre erection painting works as per (d) in sl.no.1340 above. , same as sl. no. 1340 above, but for structural steel painting worksalone excludingsupplying, transporting, storing, fabricating & erecting in position structural steel works and excluding pre erection painting works as per (d) in sl.no.1340. , supplying, transporting, storing, fabricating and fixing in position ms steel inserts (withlugs)asshownin drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain,reinforced cement concrete members inclusive of adjusting shuttering & reinforcement/any other fixture, welding where ever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts,& painting with one shop coat of inorganic zinc silicate primer and finsihing with two coats of anti rust epoxy paint of approved brand and colour ,etc complete as perdrawing,specification and direction of engineer in charge. , supplying, fabricating, fixing and keeping in position at all levels and locations threadedm.s. anchor bolts of all diameters andnomenclature including nuts, washers, anchor plates, washer plates, closure plates, pipe sleeves etc. in foundations, pedestals, etc. as directed including handling & transporting, straightening if required, turning from relevant size. m.s. rounds to required diameter, threading, welding, providing necessary templates and auxillary dummy structure, if any, necessary tying and welding, providing necessary templates and auxillary dummy strucutres, if any, necessary tying and welding with reinforcement bars, adjustment of shuttering & reinforcement/any other fixture, greasing exposed metal surfaces, covering bolts and packing the sleeves with jute cloth etc. all complete as perdrawing and specification and direction of engineer in charge. , supply, fabricating, transporting to site and erecting in position ms gates/grills as per drawings using steel confirming to is:2062 / is:1161 including supply and fixing of all materials such as hinges, locking arrangement, pluger bolts, ci wheels and fixtures, ms rail for wheel with anchor etc, all complete as directed by engineer in charge. rate shall include material costs,labour charges,all inserts and embedments essential for smooth operation of the gate. the rate shall also include two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer. , supplying, transporting, fabricating, erecting and fixing in position as per the specifications, electroforged hot dip galvanised gratings (gi coating weight shall be 305gm/sqm as per is 4759) of the approved design and pattern and erecting & fixing of fabricated steel work on operating floors, platforms, stair landings & treads,drain cover etc., at various levels including supply of all gi fixtures like edge plates for treads,clips, studs, bolts, welding if required and nosing for the treads and etc., complete, as per drawings, specifications & as directed by engineer in charge. , supplying galvanised ms chequered plate,transporting ,cleaning & fabricating & fixing on floors as cable trench covers including grinding edges & supplying all bolts,nuts ,washers etc. complete .the galvanised ms chequered plate(6mm to 10mm thick) to be fixed to the supporting beam with help of 12mm dia. counter sunk bolts at 400mmc/c including necessary modifications for supporting structure,drilling holes in plates and supporting structures etc. all complete as per drawings,specifications and directions of engineer in charge. , providing and fixing double scaffolding(cup lock type) on the exterior side, up to three story height made with 40mm dia m.s. tube 1.5m centre horizontal and vertcical tubes joining with cup and lock system with m.s. tubes challies, m.s. clamps and m.s. staircas systems in the scaffolding for woking platform etc. and maintainingit in a serviceable condition for the required durationas approved and removing it there after. the scaffolding system shall be stiffened with bracing and runners, connection with the building etc., whereever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in charge. the elevational area of the scaffolding shall be measured for payment purpose. the payment will be made once irrescpective of duration of scaffolding. , supplying, fabricating, erecting stainless steel works including gratings (ss grade 304 )to required profile and size as filter in drain with necessary fittings including straightening if required, cutting, bending, welding,grouting , cleaning, surface preparation as per specifications etc. all completed as specified and directed by engineer in charge. , providing necessary barricading workswith 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3 m , embedding the same in firm ground etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works.the same will be the property of contractor. , providing and laying to required camber granular base wet mix macadam , comprising of coarse aggregate 53 mm & down size as per specification including preparation of mix in approved mixing plant with controlled addition of water ,spreading with paver finisher or motor grader & rolling with 10 mt roller(vibro roller) in layer of compacted thickness 150mm as directed by engineer in charge. , providing and laying reinforced np3 class (medium duty) rcc hume pipe of 300mm dia. with collars jointed with stiff mixture of cement mortar in the proportion of 1:2(1cement:2m sand)for road crossing etc.including cutting, lowering, laying in position , with proper level, slope , testing of joints etc. as per specifications and directed by engineer in charge. , same as sl. no. 1460 above,but for 450mm diameter. , supplying and fixing at site chain link wire net fencing with chain link fence fabric of 50x50 mm diamond mesh of 2.5mm dia gi innerwire insulated with minimum 1.5mm pvc to achieve outer dia not less than 4mm to intermediate, corner, straining, starting or end post of ms angles/post/strut and one horizontal strand of 8 swg (4mm) dia gi inner wire insulated with pvc for tension in chain link (at middle) , gi staples for fixing chainlink in the intermediate posts and 10mm dia 175mm long hook bolts (threaded portion being 75mm long minimum) for fixing each link of the chain link; with all labour and materials but excluding cost of all ms angle postetc. complete as per drawings and directions of engineer in charge. , supplying, fixing and tensioning in position on rcc posts, 12 gauge, 2 ply, 4points, gi barbed wire designation a 1 confirming to is:278 in horizontal rows for barbed wire fencing etc with necessary gi staples, clips and pins, gi straining bolts and binding wire, etc. complete as per specifications and directions of engineer in charge. , supplying and fixing at site welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint over a coat of primer including cost of materials,labour, tools,tackles all complete as directed by engineer in charge. , concertinacoilfencing: providing and fixing 750mm dia green colour painted razor type concertina fencing with all required clips, pins, etc as per the specifications(each concertina coil piece stretch to 9m length) concertina coil shall be fixed to the m.s. angle with 4 rows of same concertina runner wires over exisiting x type angle supports as per drawings. rate shall be quoted on running metre of compound wall basis. a.diameter of coil: 750mm, number of circles and number of clips are 72 and 180 in each 9m of length. b.central core wire: core wire shall be of 2.6mm diameter made of high carbon spring steel of high tensile strength having minimum galvanizedcoating thickness equivalent to 230 grams per sq.m. c. razor strip: 0.5mm thick hot dip galvanized and of width 19mm having series of barbed punched all along the length at regular intervalshaving minimum galvanized thickness of 12 microns. hardness of tape should be between 137 180 vpn (victor penetration number) d. clips: 1.5mm thick made out of stainless steel. e. runner wire: shall be of same specifications as of central core wire. , supply of unskilled class i labourto carry out petty works not assessable for measurements/minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools. , same as sl. no. 1520 above,but for supply of unskilled class ii labour , same as sl. no. 1520 above,but for supply of mason. , same as sl. no. 1520 above,but for supply of plumber. , same as sl. no. 1520 above,but for supply of carpenter. , same as sl. no. 1520 above, but for supply of stone cutter. , same as sl. no. 1520 above, but for supply ofwelder/cutter/grinder including all consumables, necessary machineries, tools and tackles , ppeand with valid cpcl welders certificate. , same as sl. no. 1520 above, but for supply offitter including all consumables, necessary machineries, tools and tackles and ppe. , same as sl. no. 1520 above, but for supply ofrigger. , supply of jcb on hire basis on all days including sundays on 8 hrs.shift including driver,assistant /fuel/oil/lubricants /all consumables etc. complete. the quoted rate should include mobilization, operator crews/driver /assistant cost,tools, tackles etc., as directed by the engineer in charge. , supply ofpoclain pc 200on hire basis including fuel/oil/lubricantsfor excavating , levelling to required slopes and dumping at designated places within thesite premises. the quoted rate should include mobilization,operator crews/driver cost, loading, transporting, unloading, tools, tackles etc. complete as directed by engineer in charge. , same as sl. no: 1620 above, but for supply of crawler mounted dozzer. , same as sl. no: 1620 above, but for supply of tippers of capacity not less than 10 cu.m , same as sl. no: 1620 above, but for supply of taurus/approved equivalent tippers of capacity minimum 15 cu.m , same as sl. no: 1620 above, but for supply of mini poclain 30. , same as sl. no: 1620 above, but for supply of tractor mounted dozzer . , supply of 20 feet trailer with tractor on hire basis on all working days from monday to saturday on 8 hrs.shift ,inclusive ofdriver,one assistant,all consumables like diesel etc.,with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization,operator crews/driver /assistant cost, loading, transporting from site to scrap yard within refinery premises, unloading,tools, tackles,wire ropes,pulley blocks,belts,chains etc. for lifting,aligning,tying,stacking etc. all complete as directed by engineer in charge. , same as sl.nono. 1680 above but for tractor with trailer of minimumcapacity 2.5 cu.m. , same as sl.nono. 1680 above but for 40 feet trailer with tractor . , supply of front cabin hydraof minimum capacity12 t on hire basis on alldays including sundays on 8 hrs.shift ,inclusive of driver,one assistant,all consumables like diesel etc.,with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization,operator crews/driver /assistant cost, loading, transporting, unloading, labour, tools, tackles etc. complete as directed by engineer in charge. , supply ofskylift of minimum capacity 300kg for maximum working height upto 20m with high manoeuvrability and hydraulically operated on hire basis on alldays including sundays on 8 hrs.shift with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization,operator cost, diesel charges,transporting, demobilisation etc. complete as directed by engineer in charge. , supply of 400amps welding rectifieron hire basis on alldays including sundays on 8 hrs.shift with all safety precautions within cpcl refinery premises.the quoted rate should include mobilization, transporting, demobilisation costs etc. complete as directed by engineer in charge. , same as sl.no1730 above but for supply of dg set of minimum capacity 63kva including diesel charges . , supply of gully sucker truckon hire basis for removal of oil sludge with inbuiltvacuum suction using super suction machine and tanker of minimum 6 kl capacity with necessary suction/ delivery hoses of sufficient lengths and personnels of 2(two) nos. in addition to a driver and cleaner to handle the floating oils on storm water pond/drains on regular basis on all working days from monday to saturday (8 hours/day starting from the reporting time at site). the quoted rate should be for supply of one gully sucker truck as specified above on hire basis, inclusive of charges towards fuel/oils/lubricants, operator crews /driver costs, all labour, tools, tackles, mobilization, loading, transporting, unloading in the refinery premisesas directed by the engineer in charge. , pumping out watercaused by natural ground water sources, broken water mains of drains adn the like using diesel/ electric power driven self priming pumps of adequate capacity with necessary discharge and suction hoses to required length including hire, fuel/oil and operator cost etc. complete as directed by engineer in charge. , providing and bunding with sand filled bags of min 0.5 cu.ft. in capacity for maintaining and diverting the flow of water etc. including supply and filling of sand, stitching of the bags, carting to site of work to any distance, keeping position as directed, plugging holes and paddling etc., with all labour, materials, tools plants including the cost of sand and empty gunny /polythene bags etc. complete as directed by engineer in charge. , cleaning of man holes dechocking and flushing of industrial ows/fecal sewage lines of different diameters between two manholes with drain cleaning rods, bamboos strips flushing with water and compressed air, removal of sludge and disposal ofthe same at identified areas within the refinery premises upto a lead of 2km radius, as directed by the engineer in charge all labour including removing and refixing the cover slabs in position, transportation of required machinery tools, plants etc., complete taking all safety precautions as specified. thecompressed air and water at one point shall be supplied free of cost, if required.for catch basins/pits/inspection/gully trap chambers etc. , providing and laying 60mm thick factory made cement concrete interlocking rubber mould paver block of m30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in two or more colour and pattern over and including 50mm thick compacted bed of coarse sand filling the joints withsand etc. all complete as per the direction of engineer in charge. , supplying, transportation, installing, dismantling and removing of interlocking type temporary steel sheet piles with crane, vibro hammer/pile driving machinery of adequate capacity and other ancillary equipment, including driving and joining the sheet piles as per specification up to levels as per specifications & directed by eic. installed sheet piles are temporary and shall retain the earth, provide excavation support for a depth of 6m from ground level and protection against water seepage & sliding of earth during construction activities.including supply of all materials, steel members, welding, strutting, tie members supporting, labour, plant & machineries, etc. all complete as directed by engineer in charge. (note: 1. method of measurement for payment will be the actual horizontal limit of temporary sheet piling installed and accepted, and the vertical limit as measured from the bottom of the exposed face of the sheeting to the top of the retained earth behind the sheeting. 2. the steel sheet piles shall be supplied by the contractor and shall remain the property of the contractor). , providing and fixing20 mm nominal outer dia chlorinated poly vinyl chloride(cpvc) pipes, of approved equivalent make withholder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb,spacing of jumpers shall be minimum 1mc/c etc. all complete including jointing with bonding solution of approved quality and makeincluding clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , same as sl. no: 1810 above, but for 25mm nominal outer dia. pipes , providing and laying of hot applied thermoplastic compound 2.5mm thick asroad marking strips including reflectorising glassbeads @ 250 gms per sq.m area,thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35. the finished surface to be level uniform and free from streaks and holes etc. complete as per morth specificationand as directed by engineer in charge. , providing and fixing glow studs of size 100x20 mm made of heavy dutybody shall be moulded asa (acrylic styrene acryloretrite ) or hip (highimpact polystyrene)having electronically welded microprismaticlens with abrasion resistant coating as approved by engineer in charge.the glow stud shall support a load of 13635 kg tested in accordance with astm d4280. the slope of retroreflective surface shall be 35(+/ 5)degress to base .the reflective panels on both sides with at least 12 cm of reflective area up each side. the luminance intensity should be asper thespecification and shall be tested as described in astm i: 809 as recommended in bs: 873 part 4 : 1973. the studs shall be fixed to the road surface using the adhesive conforming to is, as per procedure recommended by the manufacturer complete and as per direction of engineer in charge. , supply of diesel run vehicle mounted hydraulic operated high pressure suction cum jetting sewer cleaning machineon hire basis on alldays including sundays on 8 hrs.shift fitted with pumps having suction tank mounted including water jetting pipes & accessories, suction hose pipe, discharge pipes, all materials, consumables, tools & tackles, etc.,skilled driver cum operator, required helpers for carrying out the jetting / suction operations, cleaning of ows pits, pipelines and manholes etc. as per the directions of engineer in charge. rate includes mobilization, demobilization, charges for hoses of minimum length of 100m. => limited...

Indian Army - Tamil Nadu

32799786 construction of 35 x 20 feet underground bunker / shelter with two toilets at makri , items , earth work in excavation by mechanical means ( hydraulic excavator ) in trenches for foundations, drains, pipes, cables etc ( not exceeding 1.5m in width ) and for shaft, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5m including getting out excavated earth and disposal of surplus excavated earth as directed within a load of 50 meters etc. in ( all kinds of soil 60% ordinary rock 30% and hard rock 10% ) ( specification as per ser no 1 of appx b to part ii of rfp ) , p / l in position cement concrete 1.5:10 mix clean : 5 coarse sand : 10 graded stone aggregate ( specification as per ser no 2 of appx b to part ii of rfp ) , p / l in position cement concrete in 1:3:6 mix ( 1 cement 3 coarse sand: 6 graded stone aggregate ) using 30% stones ( specification as per ser no 3 of appx b to part ii of rfp ) , p / l plain conc 1:3:6 mix clean : 3 coarse sand : 6 graded stone agg. ) using 30% stones ( specification as per ser no 4 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in col’s ( specification as per ser no 5 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in bem / slab ( specification as per ser no 6 of appx b to part ii of rfp ) , reinforcement for rcc main ( specification as per ser no 7 of appx b to part ii of rfp ) , p / l 50mm thick cement concrete flooring ( specification as per ser no 8 of appx b to part ii of rfp ) , p / l 15mm plaster in 1:6 mix ( specification as per ser no 9 of appx b to part ii of rfp ) , p / l 6mm plaster to ceiling in 1:3 mix ( specification as per ser no 10 of appx b to part ii of rfp ) , centring and shutter including strutting propping etc of removal of form ( specification as per ser no 11 of appx b to part ii of rfp ) , soffit 1 x 35’ 0” x 20’ 0” ( specification as per ser no 11 of appx b to part ii of rfp ) , edges of slab ( specification as per ser no 11 of appx b to part ii of rfp ) , beams ( specification as per ser no 11 of appx b to part ii of rfp ) , column ( specification as per ser no 11 of appx b to part ii of rfp ) , filling of available earth at top of roof ( specification as per ser no 12 of appx b to part ii of rfp ) , p / l earth filling giving bags to side earth filing at top ( specification as per ser no 13 of appx b to part ii of rfp ) , white washing with lime to give an even ( specification as per ser no 14 of appx b to part ii of rfp ) , carriage of sand for an av 100km by mt , carriage of agg stone for any av.45 km by mt , carriage of stone for av 10 km by mt , carriage of cement for an av 10km by mt , add provision for door, ventilator including fixing , add provision for electrification , 02 x toilet complete ( 4’ 0” x 6 x 0” ) ( specification attached ) ( specification as per ser no 15 ( g ) of appx b to part ii of rfp ) => limited...

Indian Army - Tamil Nadu

32799776 construction of 35 x 20 feet underground bunker / shelter with two toilets at village sher , items , earth work in excavation by mechanical means ( hydraulic excavator ) in trenches for foundations, drains, pipes, cables etc ( not exceeding 1.5m in width ) and for shaft, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5m including getting out excavated earth and disposal of surplus excavated earth as directed within a load of 50 meters etc. in ( all kinds of soil 60% ordinary rock 30% and hard rock 10% ) ( specification as per ser no 1 of appx b to part ii of rfp ) , p / l in position cement concrete 1.5:10 mix clean : 5 coarse sand : 10 graded stone aggregate ( specification as per ser no 2 of appx b to part ii of rfp ) , p / l in position cement concrete in 1:3:6 mix ( 1 cement 3 coarse sand: 6 graded stone aggregate ) using 30% stones ( specification as per ser no 3 of appx b to part ii of rfp ) , p / l plain conc 1:3:6 mix clean : 3 coarse sand : 6 graded stone agg. ) using 30% stones ( specification as per ser no 4 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in col’s ( specification as per ser no 5 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in bem / slab ( specification as per ser no 6 of appx b to part ii of rfp ) , reinforcement for rcc main ( specification as per ser no 7 of appx b to part ii of rfp ) , p / l 50mm thick cement concrete flooring ( specification as per ser no 8 of appx b to part ii of rfp ) , p / l 15mm plaster in 1:6 mix ( specification as per ser no 9 of appx b to part ii of rfp ) , p / l 6mm plaster to ceiling in 1:3 mix ( specification as per ser no 10 of appx b to part ii of rfp ) , centring and shutter including strutting propping etc of removal of form ( specification as per ser no 11 of appx b to part ii of rfp ) , soffit 1 x 35’ 0” x 20’ 0” ( specification as per ser no 11 of appx b to part ii of rfp ) , edges of slab ( specification as per ser no 11 of appx b to part ii of rfp ) , beams ( specification as per ser no 11 of appx b to part ii of rfp ) , column ( specification as per ser no 11 of appx b to part ii of rfp ) , filling of available earth at top of roof ( specification as per ser no 12 of appx b to part ii of rfp ) , p / l earth filling giving bags to side earth filing at top ( specification as per ser no 13 of appx b to part ii of rfp ) , white washing with lime to give an even ( specification as per ser no 14 of appx b to part ii of rfp ) , carriage of sand for an av 100km by mt , carriage of agg stone for any av.45 km by mt , carriage of stone for av 10 km by mt , carriage of cement for an av 10km by mt , add provision for door, ventilator including fixing , add provision for electrification , 02 x toilet complete ( 4’ 0” x 6 x 0” ) ( specification attached ) ( specification as per ser no 15 ( g ) of appx b to part ii of rfp ) => limited...

Corporation Of Chennai - Tamil Nadu

32685543 annual maintenance contract for the tata hitachi make js 200 model hydraulic excavator bearing number ne1 of greater chennai corporation for a period of one year....

Chennai Petroleum Corporation Limited - Tamil Nadu

32609202 collection and disposal of surplus earth, construction debris and other non metal debris to a place outside cpcl manali refinery for 2022 23 group 1 and 2 collection and disposal of surplus earth, construction debris and other non metal debris to a place outside cpcl manali refinery for 2022 23 group 1 and 2 , disposal of surplus earth group 1 , collecting, transporting and disposing the earth, construction debris, building rubish and other refuse materialssuch as waste insulation, papers, plastics and garden / tree waste, etc., ( excluding metal scrap and electrical / instrument cable materials ) to be removed from refinery premises including etp, mtf and ttp area aftersegregation of steel scrap, electrical / instrument cable and other serviceable materials, etc.to the designated area ( amullaivoyal / vaikkadu village ) outside the refinery premises upto a lead of 7.00km, including re excavating the deposited soil excavated earlier & stacked, transportation, loading, unloading, laying at all depths& heights, stacking, levelling and dressing both areas ( viz., from where the earth is transported and where it is deposited ) to required levels and slopes complete with all lifts using mechanical means ( hydraulic excavators / trucks ) / manually as directed by engineer in charge. ( note: the payment shall be made on quantities, measured on truck basis with 30% deductions for voids ) , disposal of surplus earth group 2 , collecting, transporting and disposing the earth, construction debris, building rubish and other refuse materialssuch as waste insulation, papers, plastics and garden / tree waste, etc., ( excluding metal scrap and electrical / instrument cable materials ) to be removed from refinery premises including etp, mtf and ttp area aftersegregation of steel scrap, electrical / instrument cable and other serviceable materials, etc.to the designated area ( amullaivoyal / vaikkadu village ) outside the refinery premises upto a lead of 7.00km, including re excavating the deposited soil excavated earlier & stacked, transportation, loading, unloading, laying at all depths& heights, stacking, levelling and dressing both areas ( viz., from where the earth is transported and where it is deposited ) to required levels and slopes complete with all lifts using mechanical means ( hydraulic excavators / trucks ) / manually as directed by engineer in charge. ( note: the payment shall be made on quantities, measured on truck basis with 30% deductions for voids ) => limited...

Indian Army - Tamil Nadu

32585560 construction of 35 x 20 feet underground bunker / shelter with two toilets at makri , items , earth work in excavation by mechanical means ( hydraulic excavator ) in trenches for foundations, drains, pipes, cables etc ( not exceeding 1.5m in width ) and for shaft, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5m including getting out excavated earth and disposal of surplus excavated earth as directed within a load of 50 meters etc. in ( all kinds of soil 60% ordinary rock 30% and hard rock 10% ) ( specification as per ser no 1 of appx b to part ii of rfp ) , p / l in position cement concrete 1.5:10 mix clean : 5 coarse sand : 10 graded stone aggreagate ( specification as per ser no 2 of appx b to part ii of rfp ) , p / l in position cement concrete in 1:3:6 mix ( 1 cement 3 coarse sand: 6 graded stone aggregate ) using 30% stones ( specification as per ser no 3 of appx b to part ii of rfp ) , p / l plain conc 1:3:6 mix clean : 3 coarse sand : 6 graded stone agg. ) using 30% stones ( specification as per ser no 4 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in col’s ( specification as per ser no 5 of appx b to part ii of rfp ) , p / l rcc 1:1.5:3 as in bem / slab ( specification as per ser no 6 of appx b to part ii of rfp ) , reinforcement for rcc main ( specification as per ser no 7 of appx b to part ii of rfp ) , p / l 50mm thick cement concrete flooring ( specification as per ser no 8 of appx b to part ii of rfp ) , p / l 15mm plaster in 1:6 mix ( specification as per ser no 9 of appx b to part ii of rfp ) , p / l 6mm plaster to ceiling in 1:3 mix ( specification as per ser no 10 of appx b to part ii of rfp ) , centring and shutter including strutting propping etc of removal of form ( specification as per ser no 11 of appx b to part ii of rfp ) , filling of available earth at top of roof ( specification as per ser no 12 of appx b to part ii of rfp ) , p / l earth filling giving bags to side earth filing at top ( specification as per ser no 13 of appx b to part ii of rfp ) , white washing with lime to give an even ( specification as per ser no 14 of appx b to part ii of rfp ) , carriage of sand for an av 100km by mt , carriage of agg stone for any av.45 km by mt , carriage of stone for av 10 km by mt , carriage of cement for an av 10km by mt , add provision for door, ventilator including fixing , add provision for electrification , 02 x toilet complete ( 4’ 0” x 6 x 0” ) ( specification attached ) ( specification as per ser no 15 ( g ) of appx b to part ii of rfp ) => limited...