40151195
tender for park development at perumbakkam, chennai; 1 civil works 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling m sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 supplying and filling approved river sand of specified quality for sand pits in play zone area. the rate including the cost of sand, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, loading, unloading, spreading in layer not exceeding 150 mm thick, watering, ramming, compacting with mechanical compactors and / or other equipment to specified levelall complete and as per the standard specification. 5 plain cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 6 plain cement concrete 1:2:4 ( one cement two sand and ten broken machine crushed stone jelly ) using hbg machine crushed stone jelly of size 20mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 8 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 9 for plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc. 10 providing and laying m 30 design mix for all reinforced cement concrete with minimum cement content conform to is 456 2000 using ordinary portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for raft, grade beam, shear wall, rcc walls, lift walls, plinth beams, column, footings, grade slab, roof slab & beam, curved slab, beam, column drops, pergola, staircase waist and landing slab lintel, sunshades, parapet cum drops, steps, canopy, window boxing slab, loft, fins facia planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items.rate to include all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in rcc slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the engineer in charge 11 basement concrete work 12 ground floor concrete work 13 providing under reamed pilesr.c.c.38 cm ( 15 ) dia cast in situ with single reamed ( bulb ) in cement concrete1:1.5:3, 11.5cm above g.l. including boring, erecting, vibrating, curing, hire charges for drilling equipments, etc., complete as per relevent isi specifications ( excluding cost steel reinforcement ) . 14 bored pile 450 mm diaproviding and installing bored cast in situ reinforced cement concrete pile ofspecified diametre and length below thepile cap in rmc m25 concrete to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including bentonite solution machinery charges labour chargres etc., all complete. ( length of pile for payment shall be measured from bottom pile to the bottom of pile cap ) 15 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 16 brick masonry in cement mortar 1:5 ( one cement and five sand ) in foundations, basement and superstructure walls using second class ground moulded chamber burnt bricks of size 9”x 43 / 8”x2 3 / 4” etc., complete complying with standard specifications and drawings and as directed by departmental engineers 17 basement brick work 18 ground floor brick work 19 brick partition walls of 11.50cm thickness using best quality ii class ground chamber burnt bricks of size9 x 43 / 8 x 23 / 4 in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. 20 supplying and filling brick bats of size various from 20to40mm in regular layers of 15cm thick including watering, consolidating and rolling with hand roller, etc., complete as per direction of engineer in charge 21 supplying and filling in foundation, basement, etc with filling gravel inwellrammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 22 supplying and stacking of red earth at site to the departmental guage for premeasurements which is of light textured, crystalline, porous and firable and not of generally acidic or neutral but not of alkaline and should not of alkaline and shoulde be fertile. the rate including seignior age charges, cost of red earth, transportation, loading & unloading, stacking etc., complete and as directed by engineer in charge. 23 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 ( one cement and three sand ) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers 24 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 25 supplying and painting of2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. the rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the engineer in charge. 26 providing granolithic floor finish 25mm thick with pcc 1:2:4 ( one cement two sand and four aggregate ) using 10 to 12mm thick hgb jelly and river sand and including rubbing the top surface smoothly thread lining if found necessary and curing etc., complete complying with standard specification and as directed by the departmental officer 27 providing and laying granular sub base ( gsb ) by provided coarse graded material confirming to ( table 400 1 ) mixing in a mechanical mix plant at omc carriage of mixed material to work site spreading in uniform layers with motor grader on prepared surface and compacted with vibratory power roller to achieve the desired dry density to the required grade and cross slope as per drawings all others incidental charges etc.complete as per clause of 401 morth specification 28 structural steel works:supplying fabricating, hoisting, erecting and fixing in position mild steel structural steel works of pergola, gate for compound wall and grill at all elevations, levels and heights including aligning, leveling, providing and fixing bolts, nuts, washers, comprising ms plates, flats, squares etc., of various sizes and other structural steel sectionsconforming to latest is2062 grade a&b including straightening, cutting, welding, bending to shape, bolting and inclusive of the following finishes. the rate including cost of all materials, labour chanrges, scafolding, stagging, transportation, lead & lifts, wastage, etc., complete with all respects complying with relevant standard specification, as directed by the engineer in charge. all ms members shall be painted with one coat of zinc chromite primer and 2 coats of 35 microns dft of synthetic enamel paint of approved colour and make etc, .the rate includes the cost of all materials, labour, tools, tackle and plants, wastage etc., as per specification and drawings complete. the rate quoted is to include cost of bolts, nuts, washers, welding, electrodes and connections required for the work. no extra on this account will be paid for. the rate to include preparation of fabrication shop drawings for owners approval: 29 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( the make quality and colour of paint should be got approved by the executive engineer before use on works. ) 30 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 31 solid pvc door shutters using 19 gauge 19mm ms square tubes for styles and outer frames. 15mm ms square tubes for top, lock and bottom rails. the steeltubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the over all size of styles shall be 50mm x 30mm. the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. the over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutte 32 providingcountry wood wrought and put up frame for door and window any other similar joinery works using following size of upto 4m in length country wood scantling of pillai maruthu or patak including labour for wrought and putup in position etc., complete complying with standard specification.. 33 frp door suitably reinforced using ms angle / flats, cost of holdfasts and solid core frp shutter panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by engineers 34 upvc windowspecification:supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 125gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work 35 upvc ventilatorspecification:supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with gi / 1mm 125gsm and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiations pin headed glass 4mm thick should be provided in the louvers. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the ventilator should be got approved from the executive engineer before use on work 36 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 37 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 38 flooring with followingdesigned antiskid ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 39 dadooing walls with following best approved quality, designed colour ceramic tilesof following sizes set in cement mortar 1:2 ( one cement and two sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 40 supplying and laying interlocking rubber moulded paver 83mm thk of approved sample as per design / drawing made of m40 concrete 83 mm thick includingtransportation of the blocks to the site preparation of surface including supplying and filling with manufactured sand to 50 mm thick, levelling and compacting with plate vibrator and laying of the inter locking paving blocks with sand binding and final compaction with plate vibrator of 3 tonne capacity finishing the surface including cutting of blocks at the edges including all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 41 supplying and layingmanhole cover sfrc with size of 750mm x 750mm including all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 42 supplying and laying pvc mould ci steps for sumpincluding all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 43 supplying and fixing colour metal roofing sheets made up of galvalumed aluminumzinc alloy coated steel, az 150 and hitensile grade 550 steel of thickness 0.47mm, trapezoidal profile over all width 1080 mm etc as per direction of engineer in charge 44 supplying and fixingweld mesh of size 7.5x2.5cm 10 gaugeincluding all labour, materials, transportation, shifting, welding chargesetc., complete, as directed by the engineer in charge 45 providing and fixing 18mm thick machine cut, mirrorpolished, premoulded and pre polished machine cut granite for platforms, seating top finished copping, etc., of approved qualityfor wash basin / vanity counters, pantry etc.of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 ( 1 cement:4 m sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. 46 plumbing 47 supplying and fixing in position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 48 supplying and fixing in position best quality pvc soil / waste pipes of various dia having 6 kg / sq.cm. pressure bis mark and providing leak proof joints using pvc adhesives including fixing to the wall with special pvc / ms clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / rcc works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. ( the pvc pipes should be got approved by the executive engineer before use on works ) . the rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level 49 supply and delivery and fixing of hdpe tankincluding loading, unloading, transportation and labour charges for fixing of the pipes and specials for pipe connection works including cutting, threading and fixing charges etc., 50 supplying and fixing in position first quality and approved variety of gun metal gate valve / wheel valve with bis make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements ) .the valves to be used on work shall be got approved by the executive engineer before use on work. 51 32mm gun metal gate valve 52 40mm gun metal gate valve 53 supplying and fixing in position 15mm dia brass long body tap ( heavy duty ) of approved make conforming to bis specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. ( taps should be got approved by the executive engineer before use on the works ) 54 sd tap 55 pillar tap 56 supply andlaying and jointingupvc pipe ( un plasticized polyvinyl chloride ) upvc used for commercial applications operate and designed to handle higher water pressure ( schedule 80 ) including cost of such specials and fixing in position dismantling masonry and make the same to original conditionetc complete complying with standard specification and as directed by the departmental officers at site of work. 57 25mm dia 58 32mm dia 59 supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm ( with pedestal / without pedestal ) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. ( the wash hand basin and specials should be got approved by the executive engineer before use on works ) . 60 supplying and fixing in position cp shower rose with cp stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers ( the cp shower rose should be got approved by the executive engineer before use on works ) . 61 supplying and fixing in position indian make bevelled edge mirror of approved quality and brand pvc / fibre glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. ( the mirror should be got approved by the executive engineer before use on woks ) 62 supplying and fixing in position white / glazed european water closet of best quality and approved make with 100 mm p or s trap connecting with ci pipe of 100mm dia / pvc pipe of 110mm dia, double flapped rigid pvc black seat and seat cover with cp brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity pvc porcelin low level flushing tank with a pair of ci brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white pvc flush hand using indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm gm wheel valve, 15mm brass nipple ( 2 nos. ) , 15mm nylon connection, tw plugs, screws and also giving necessary connection to the pvc pipe including cost of 600mm length of 110mm dia pvc pipe and painting the ci brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re doing the dismantled masonry to original condition etc. complete complying with standard specifications. ( the ewc and flushing tank wiht all accessories should be got approved by the executive enginer before use on works ) 63 supplying and fixing position ci nahani trap / floor trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( one part of lime, two part of sand and five part of 40mm gauge brick jelly ) and finished with cement mortar 1:3 ( one cement, three sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the ci / pvc pipes, etc., complete complying with standard specification. ( the nahani trap should be got approved by the executive engineer before use on works ) 64 supply and fixing in position of best indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with gi pipe, 32mm dia bell mouth pvc connection and waste pipe, 15mm dia gi pipe of required length, 15mm dia gm wheel valve, 15mm dia brass nipple 2 nos., and fixing the urinals in position with necessary tw plugs, clamps, screws, etc., including dismantling masnory and re doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. ( the urinal should be got approved by the executive engineer before use on works. ) 65 bore well 66 drilling bore well anywhere in chennai city including transportation from one place to another place within alluvial soil or sedimentary rock clay and sand or stone pebbles, boulders etc., by first taking a pilot bore of 140mm / 150mm / 200mm and the enlarging to required depth direct or reverse rig fuel, drilling the betonite mud and water required for drilling by departmental officers including construction of mud pts. ( water available with a lead of 1.50km ) 67 300mm 68 150mm 69 reaming from 200mm pilot bore to 300mm dia bore upto 60m depth ending below ground level and as directed by the departmental officers. 70 supply and laying following dia pvc casing pipe with excise duty as per is 12818 / 1992 71 200mm dia cs ( plain pipe ) 72 200mm dia rs 73 150mm dia rs 74 labour charges for inserting pvc casing pipes assembly ( with slots or without slots ) in the drilled hole including jointing the pipes with pvc couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the executive engineer of departmental officers. 75 200mm dia cs ( plain pipe ) 76 200mm dia rs 77 150mm dia rs 78 supplying and filling with river pebbles in annular space between bore and pvc pipe up to hard rock. 79 charges for developing the borewell with air compressor of 300 cfm capacity ( minimum 8 hours ) including transportation labour and fuel charges for compressor as directed by twad board officers and conducting yield test by v notch method. 80 supplyand erection of 2.hp submersible pump set using nylon rope including cost of motor , fixing necessary cable charges and labour charges etc., complete ( for sump & bore well ) 81 supplying and fixing in position best quality of hdpe pipes with isi mark of following dia with specials including cost and coveyance of hdpe pipes and specials, labour charges for erection of pipes in the borewell and jointing materials etc., all complete as directed by the departmental officers. 82 dismantling removing reinforced cement concrete work and etc., by mechanical means including stacking of steel bars and disposal of unserviceable material within 50m lead as per direction of engineer in charge 83 conveyance of earth / debris to a lead of within 30 km from site as directed by the engineer inculding loading, unloading, hire charges for vehicle and other incidental charges etc., all complete as directed bythe departmental officers. 84 supplying and erecting in position of following liters capacity industrial model reverse osmosis water cum purifier to deliver potable water with world health organisation ( who ) standards with following accessories. ( a ) ms skid 1 no. ( b ) media 11054 no. vessel with 20 nb multiport valve ( with media pubble and fine sand and activated carbon filling ) set ( c ) feed pump 0.50 hp – 1 no. ( d ) vertical pump 2 9, 2.00 hp / single phase – 1 no. ( e ) membrane 40 x 40 filmtech ( or ) equilaents / osmonic ( usa ) 1 no. and membrane pressure vessel 40 x 40 1 no. & pressure gauge 2 nos. ( f ) flow meter 1 no. 20” filter with housing 1 no., low pressure switch 1 no., level switch 1 no. & necessary cpvc pipes and fittings. the system shall be provide with two panel control system with necessary stainless valves and fittings and float control etc. the rate should be inclusive of all civil works, wherever necessary to install the system in position and intact. 50 litres 85 supply and fixing of water co2 stored pressure type 9 litres capacity fire extinguisher as per new is 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the departmental officers. 86 supplying and planting of black eyed susanvariety of height 6 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 87 supplying and planting of thornless velvet rose variety of height 1 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 88 supplying and planting oflilium longiflorum variety of height 1 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 89 supplying and planting of quisqualis indica variety of height 13in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 90 supplying and planting of bougainvillea variety of height 16in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 91 supplying and planting of hydrangea macrophylla variety of height 9in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 92 supplying and planting of vinca minor variety of height 3in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 93 supplying and planting of acalypha variety of height 1in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 94 supplying and planting of canna indica varigatedvariety of height 14in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 95 supplying and planting of coleus plant ornamentalvariety of height 1in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 96 supplying and planting of cypress tree variety of height 6 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 97 supplying and planting of dypsis lutescenstree variety of height 8 10 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 98 supplying and planting of plumeira albatree variety of height 8 10 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 99 supplying and planting of polyalthia longifolia tree variety of height 8 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 100 supplying and planting of neem treevariety of height 8 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 101 supplying and planting of coccoloba uniferatreevariety of height 810 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 102 supplying and planting of mimusops elengitreevariety of height 810 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 103 supplying and planting of moringa oleifratreevariety of height 3 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 5 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of requiredsize, planting of sapling, refilling of excavated earth etc as directed by the site in charge 104 supplying and planting of tabernaemontana divaricatavariety of height 16in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 105 irrigation work 106 supply, fixing & commissioning of pop up spray head robust design 1804 seal a matic ( sam ) pressure regulating series spray bodies, with rotary nozzle with capable of covering 4.0 7.3m at 1.4 3.8 bars pressure, rotary nozzles shall have hand adjustable ( without tools ) radius and arc 45 to 270 degree or full circle true flushing mechanism, thick streams andlarge water droplet & low precipitation rate. triple blade wiper seal precisely balances flushing, flow by and debris rotection to optimize performance and durability at pop up and retraction. precision controlled flushing at pop up and retraction clears debris, ensuring positive stem retraction in all soil types. unique debris pockets hold grit in place, removing it from circulation and preventing long term damage. parts resistant to corrosion in treated recycled water containing chlorine. pop spray body shall with stand upto 6.9 bar. built in seal a matic™ ( sam ) check valve. traps water in lateral pipes in elevation changes of up to 14 feet ( 4.2 have a double lacquering made out of highly concentrated fluomax pvdf on both side, double pvc coating and be weldable without grinding to make sure the fabric have less environmental impact the fabricator has to deliver evidence of r park 107 supply, fixing & commissioning of 5004 plus sam prs series rotor pop up sprinkler full / part circle having radius of 6.7m 12m @ 2.5 4.5 bar with discharge of 0.09 0.61 ltr. / sec. the sprinklers having arc adjust thru top cover w / std. screwdriver the sprinkler is gear driven rotary type with having 3 / 4 bottom inlet. oversized wiper seal, rain curtain technology, gentle closein watering and self flushing arc adjustment port and also having tapered riser stem with wiper seal the sprinkler shall have plus ( pressure loss ) flow shut off, 45 psi pressure regulator with flow optimizer technology, internal seal a matic device which prevents low head drainage ( upto 3.1m ) & hence puddling & erosion. the body of sprinkler is of non corrodible, heavy duty, anti breaking system plastic. o ring slip clutch, racheting slip clutch, side inlet available 6 and 12, turret mounted internal dia plugs, flow stop available, non potable water indication available etc., complete including installation charges. ( rain bird, toro, k rain or equivalent brand ) park 108 supply of 3 / 4 pop up connecting swing joint assembly. the tubing shall beof polyetylene having wall thickness of 2.3mm, a working pressure of 5.5 kg / cm2 at 430 c and a surge pressure of 16.6 kg / cm2. the fittings shall be made of uv resistant thermo plastic.sa series including installation charges. pd 1585 109 supply of 3.0 twin disc filter 50 m³ / hr. including installation charges. ( brands like rain bird or equivalent ) pd 1587 110 flexible polyethelene irrigation pipe 16 mm dia / 2.5 / 1.1 1.4 mm cl ii. including installation charges. netafim or equivalent brands. pd 1589 111 supply of pressure compensated dripper with 2 / 4 / 8 lph outlet flow including installation charges. rain bird / netafim makeor equivalent make. pd 1591 112 supply of endcap, nipple, start nipple, rubber grommet 16 mm dia. including installation charges. netafim or equivalent brands. pd 1590 113 supply, installation, testing and commissioning of sperinkler system with 2 hp, 230v motor with 380 lpm, 2.80 kg / cm2 pressure, with a head range of 22 30 meter, suitable to support sprinkler and dripper, including installation all inclusive. 114 supply, fixing & commissioning of a double acting airand vaccum release 2 air release valve . the air release valve shall be capable of both releasing and admitting air from and into the line. the working pressure shall be 10 ksc etc., complete, the rate including cost of all materials, labour charges, transportaion charges etc., complete complying with standard specifications as per the direction of departmental engineer in charge. 115 children play equipment 116 design, manufacture, supply, erection and testing and commissioning of puppy dog rider with a size of 0.9 m x 0.40 m x 0.76 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. the rider is of size 0.9 m x 0.4 m x 0.55 m, bolts, nuts, screws, washers and etc., used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety feature. all joints are robotic welded including all civil works as required complete 117 design, manufacture, supply, erection and testing and commissioning of elephant rider with a size of 0.9 m x 0.40 m x 0.76 mcomply with en 1176 safety standards. the en 1176 certificates issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. the rider is of size 0.9 m x 0.4 m x 0.55 m. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete 118 supply and fixing of arch sea saw sea saw made of g.i.sheets with 2 stainless steel pipes boards to play 4 c hildren simultaneously. seats made of fiber reinforced plastic. 119 design, manufacture, supply, erection and testing and commissioning ofpod swingwith a size of 2.83 m x 1.30 m x 2.50 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc.all products must be tested and certified to meet en 1176 safety standards. the en 1176 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. an inverted ‘u’ shaped structural posts of height 2.50 m are to be schedule hot dip galvanized steel with a 114mm od and 2.2mm ( wall ) thickness of the tubing. the poles are welded on to a base plate made from steel with 114mm inner diameter. at top a metal sheet is provided which shall be an all robotic welded unit, fabricated fromgalvanized steel pipes. swing seats are all robotic welded fabricated the electro statically applied polyester powder has a tough finish with maximum durability. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en1176 standards. all joints are robotic weldedincluding all civil works as required complete. 120 supply and fixing of see saw 4 seater withfiber reinforced plastic of width 7ft 0” and supporting frame made of 40mm stainless steel pipes and swinging arm made of 50mm stainless steel pipes of length 8ft 0”.handle made of 19mm stainless steel pipes seats are fiber reinforced plastic etc. including all civil works as required complete. 121 design, manufacture, supply, erection and testing and commissioning of multi play system ( kpsnk 005 ) with a size of735 x 735 mm comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. the new hdpe play panels include different games, each with their own unique hdpe panel design. all panels are available in other colours or languages on request. the mounting holes must be drilled on installation. 3 in a row form three discs of your colour in a row in this classic game for two .unique hdpe panel design. solid hdpe material thickness 19 mm. available in other colours / languages on request. mounting holes to be drilled depending on installation. all joints are robotic welded. all components designed and manufactured to meet with en1176 safety standards including all civil works as required complete. 122 supply and fixing of merry go round – 6 seater ( frp ) height :3” gi pipe, 2.5mm thick, b class seat size:15” x 14”, paint: pu coating. 123 design, manufacture, supply, erection and testing and commissioning of multy play system type 1 ( kpsnk 008 ) with a size of980 x 735 mm comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. the new hdpe play panels include different games, each with their own unique hdpe panel design. all panels are available in other colours or languages on request. the mounting holes must be drilled on installation. race your sliding disc as quick as possible from start to finish. unique hdpe panel design. solid hdpe material thickness 19 mm. available in other colours / languages on request. available in other colours / languages on request. all joints are robotic welded. all components designed and manufactured to meet with en1176 safety standards including all civil works as required complete. 124 supply and fixing of duck merry go round: [ measurement ] height:2ft width:7ft [ component ] leg :3” galvanished ‘b’ class pipe seat :frp duck 4nos. with isotolic gel coat with uv pigment.support : 1 ½” galvanished ‘b’ class pipe. painting with pu coating [ wanted area ] product area : ø 7’ft play area : ø 9’ft 125 design, manufacture, supply, erection and testing and commissioning of triangle rope climber with a size of 2.33 m x 1.5 m x 1.5 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. support posts of height 2.1 m are to be schedule galvanized steel with a 89 mm od { outer diameter } . specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be oftamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 126 design, manufacture, supply, erection and testing and commissioning of hexa climber with a size of 2.2 m x 2.1 m x 2.3 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. these en 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. upright structural posts of height 2.3 m, are to be schedule galvanized steel with a 114mm od { outer diameter } . parallel climber of size 1.9 m x 1.17 m , horizontal ladder 1.9 m x 1.17 m , pull up bar, chain climber of size 1.9 m x 1.17 m, and gymnastic rings of size 0.77 m x 1.17 m shall be an all patent welded fabricated from 54 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 127 design, manufacture, supply, erection and testing and commissioning ofcrawl tunnel with a size of 1.94 m x 1.54 m x 1.3mcomply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. upright structural posts of height 1.3 m are to be schedule galvanized steel with a 114mm od { outer diameter } . the tunnel of size 1.94 m and dia 900 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 128 design, manufacture, supply, erection and testing and commissioning oftoddler multi play system type 2 with a size of4.10 m x 2.30 m x 2.60 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. with upright structural posts of height 2.0 m, are to be schedule galvanized steel with a 114mm od { outer diameter } . deck of size 0.80 m x 0.80 m and staircase of size 0.91 m x 0.39 m shall be an all robotic welded assembly fabricated from perforated solid punched steel. deck perimeter is precision pre punched for attachments. decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. handrail of height 1.5 m and dia 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. frisby climber, piped walls of size 1.52 m shall be an all robotic welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. galvanized steel for the inner parallel bars. roof of size 1.17 m x 1.17 m x 0.85 m straight slide of size 1.46 m x 0.45 m x 0.95 m. a shaped swing of size 1.73 m x 1.24 m shall be fabricated from 32mm o.d. galvanized steel pipe. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 129 design, manufacture, supply, erection and testing and commissioning of customized adventure system hps 2 with a size of10 m x 8.56 m x 4.2 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc.curved structural poles of height 2.6 are to be schedule galvanized steel with a 114mm od { outer diameter } . handrails of dia 60 shall be an all patent welded unit, fabricated from 32 o.d. galvanized steel pipes. wiggle triangle crawl of size 1.08 m x 0.13 m ( single triangle ) , stepping stones of dia 0.32 m ( single stone ) , elliptical shaped climber of size 2.12 m x 0.64 m, plastic components, net climbers shall be an all patent welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. galvanized steel for the inner parallel bars. slide of size 2.77 m x 0.46 m x 1.21 m. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotics welded including all civil works as required complete. 130 design, manufacture, supply, erection and testing and commissioning of multiplay system type 3 with a size of 10.04 m x 6.19 m x 4.2 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. upright structural posts of height 2.3 m, 2.9 m and 3.3 m are to be schedule galvanized steel with a 114mm od. deck of size 1.16 m x 1.16 m and staircase of size 1.4 m x 1.35 m shall be an all robotic welded assembly fabricated from perforated solid punched steel. deck perimeter is precision pre punched for attachments. decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. handrail of height 1.88 m and dia 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. step climber size is 1.0 m x 0.5 m x 2.7 m, piped walls of size 2.4 m, shall be an all robotic welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. monkey bar size is 2.35 m x 1.0 m x 2.13 m shall be an all robotic welded fabricated from 32 o.d. galvanized steel for the inner parallel bars. roof of size 1.5 m x 1.5 m x 0.93 m, 131 straight slide of size 1.68 m x 0.66 m x 1.8 m, wavy slide of size 3.17 m x 0.58 m x 2.4 m, spiral slide of size 1.31 m x 1.73 m x 2.7m, plastic climbers of size 1.06 m x 0.73 m x 0.96 m, tunnel, panels, plastic components. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded. all components designed and manufactured to meet with en 1176 safety standards including all civil works as required complete. 132 gym equipment 133 supply, erection and fixing of arm & shoulder wheels 1300 x 1200 x1350 mm 4mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. 134 design, manufacture, supply, erection and testing and commissioning of tai chi spinners with a size of 1.25 m x 1.09 m x 1.49 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only.the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.49 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. circular handrail of dia 477 mm made with the pipe dia of 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standards including all civil works as required complete. 135 supply and fixing of double cross walker cardio, lower / upper body exercise. main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes ( 1680 x 515 x 1780 mm ) 4 mm pipe double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. steel foot rest / foot paddle for long lasting life. 136 design, manufacture, supply, erection and testing and commissioning ofelliptical cross trainerwith a size of 1.02 m x 0.53 m x 1.52 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.25 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two numbers of foot rest of size 320 mm x 132 mm are attached to the standing bars 998 mm x 40 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. lower part of support handrails of size 0.8 m high and dia 47 mm and upper part of support handrails of size 0.51 m high and dia 32 mm are all robotic 137 welded fabricated from 47 mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 138 supply and fixing of push pull up chair promotes upper body and triceps strength lat pull down develops upper body strengths size 2900 x 775 x 2060mm main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. steel foot rest / foot paddle for long lasting life. . 139 supply and fixing of twister & leg trainer back and spinal joint exercise. strengthens abdominal and spinal. also increase flexibility of upper and lower and spinal. also increase flexibility of upper and lowerback. size 1700 x 510 x1425mm ) 4 mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes thick rexin covered cushioned seat. double coated powder coating, heavy duty sealed ball bearing, for long lasting life supply and fixing of twister & leg trainer back and spinal joint exercise. strengthens abdominal and spinal. also increase flexibility of upper and lower back. size 1700 x 510 x1425mm ) 4 mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes thick rexin covered cushioned seat. double coated powder coating, heavy duty sealed ball bearing, for long lasting life 140 resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. all joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 141 design, manufacture, supply, erection and testing and commissioning of self weight rower with a size of1.26 m x 0.80 m x 1.59 mcomply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. horizontal bars of length 1.08 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. handle bars of 0.74 m and dia 38 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 142 design, manufacture, supply, erection and testing and commissioning ofmini ski with a size of 1.07 m x 0.78 m x 1.40 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.40 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. the standing bars 991 mm and dia 60 mm. upper part of support handrails of size 1.04 m high and dia 38 mm are all robotic welded fabricated from 40mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant 143 stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 144 design, manufacture, supply, erection and testing and commissioning of bicycle of size 0.97m x 0.49 m x 1.30 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.33 m is to be schedule hot dip galvanized steel with a 60 mm o.d. and 2.2mm ( wall ) thickness of the tubing. two numbers of pedal of size 113mm x 40mm & rotating disc of dia 380 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be 145 covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 146 design, manufacture, supply, erection and testing and commissioning of squat pusher with a size of 1.93 m x 0.56 m x 1.70 mcomply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.vertical bars height of 1.50 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. l shaped bars of 960 mm x 600 mm carrying two seats of 0.34 m x 0.34 m shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured tomeet with en6630 safety standardsincluding all civil works as required complete. 147 design, manufacture, supply, erection and testing and commissioning of sit up station with a size of 1.48 m x 1.21 m x 0.63 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 0.63 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two j shaped bars of 1.07 m and dia 48 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 148 supplying and fixing of leg extension / leg curf : pl 9019 of glass fiber reinforced nylon pulleys with deep v groove provides secure cable seating and fluid bearing rotation. shroud is applied to protect the equipment or the possible injury during operation. tubing: 2.5 mm to 2.75 mm square tube differ into any types, from 30 x 60x 2.75 mm square tube differ into any types, from 30 x 60mm to 50 x 100 mm, electro welded to maximum integrity. pad total thickness is 70 mm dimension: 1465 l x 1245 w x 1520 h ( mm ) product weight: 115.5 kg / 255 lbs warranty: 1 year. 149 design, manufacture, supply, erection and testing and commissioning ofdouble air skier comply with a size of1.61 m x 0.52 m x 1.51 m with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 1.25 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. the foot rest of size 365 mm x 164 mm is fixed to the standing bars of length 1640 mm x 40 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. lower part of support handrails of size 0.8 m high and dia 47 mm and upper part of support handrails of size 0.51 m high and dia 32 150 mm are all robotic welded fabricated from 47 mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 151 supplying and fixing of lat pull down / seated row: pl 9002 of glass fiber reinforced nylon pulleys with deep v groove provides secure cable seating and fluid bearing rotation. shroud is applied to protect the equipment or the possible injury during operation equipment or the possible injury during operation tubing: 2.5 mm to 2.75 mm square tube differ into any types, from 30 x 60 mm to 50 x 100 mm, electro welded to maximum integrity. pad total thickness is 70 mm dimension: 1764 l x 1019 w x 2182 h ( mm ) product weight: 90.5 kg / 200 lbs warranty: 1 year 152 exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 153 design, manufacture, supply, erection and testing and commissioning of seated chest press with a size pof 1.82 m x 0.69 m x 1.88 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 1.88 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two pair of u shaped bars of 1.02 m and dia 40 mm while the handles are placed at a spacing of 698 mm shall 154 be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. joints are robotic welded. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 155 play equipment 156 supply and fixing of badminton court poles 2 nos. ss 304with 46 x 46 mm 3mm poles with a overall height of 2.0 m height white colour powder coated with 80 micron thick, 1550 mm above ground and 450 mm below ground, nylon net with 1.0 m heightincluding excavation, civil work including cost of all materials , labour, lead lift etc., complete. 157 supply and delivery of aluminium alloy ovel frame with steel handle badminton racquetswith overall dimension of 680 mm long, 230mm frame width, 280 mm long string area, 95 mm grip perimeter string with high quality nylon confirming to the badminton federation of india standards.. 158 supply, installation of basket ball pole of 10 feet height 65 mm dia, with back stop unit, approved colour of powder coated with 80 micron thick, 25 mm acrylic sheetincluding excavation, civil work including cost of all materials , labour, lead lift etc., complete. 159 supply and delivery of rubberbasket ball for competition ( competition in all categories size 7. with inner nylon cloth lining, the outer surface of the ball shall be made of toxic free leather or rubber material with ball circumference range from 749 mm to 780 mm and mass of 567 g to 650 g ) 160 supply and delivery of rubberfootball made out od moulded synthetic material with 32 panels, hand stitched, with a size of 580 600mm dia, weigh of 3002 to 320 grams all inclusive. 161 supply and delivery of rubbervolleyball spherical shaped, made out of moulded synthetic material, hand stitched, with a circumference, latex bladder, of 660 mm size weigh of 270 grams cotton stitching, all inclusive. 162 electrical 163 tneb metering boardsupply and fixingof tneb meter board suitable for 3 phases 100 a service connection made up of suitable iron angel frame work of size 2 feet x 1.5 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1.5 feet of 12 mm thickness with necessary bolts and nutt supports and supply, installation and commissioningof 3 nos 100 a fuse units ( 500v ) , 1 no neutral link , copper flat of size 1 x 1 / 4 with interconnection of eb meter to fuse units by 19 / 16 pvc insulated copper wire with earth connection and to complete the work etc. 164 250a isolator switch supply and fixing of 200a tpn switch disconnector fuse units in sheet steel enclosure with hrc fuses double break on suitable angle iron frame work with ms cable entry boxes with pwd earthing. 165 supply and fixing of 6 way vertical triple pole and neutral mccb sheet steel enclosure distribution board ( with mccb incomer ) with double door ( metal door ) with 1 no. 160 a 4 p mccb switch as incoming and 4nos. 63a 3p mcb , 6 nos. 6a to 32a sp mcb as outgoing with suitable cable end box on wall with earth connection only. 166 supply and fixingof8 way verticaltpmcbsheetsteel industrial type tpmcb db with ip54 protection of surface type fitted with bus bars and neutral links with1 no. of 63a fp mcb as incoming and 4 nos. of32a, 10ka triple pole mcb in flush with wall and making good of the concealed portion with earth connection. ( industrial type tpmcb db with ip54 protections ) 167 supply and fixing of 7 segment8 way63a tpn mcb sheet steel distribution board ( higher end ) with metal / acrylic doorcover flush type / surface type fitted with busbars and neutral links with single / three phase mcb outgoings and separate 4 way provision for accommodating one no. 4 pole incoming mcb / isolator and another separate 4 way provision for accommodating one no. 4 pole elcb / rcd ( totally 8 ways in one segment ) ( 3x 6 ways in each segment ) and separate provision for mcb / isolators ( totally 18 nos. ) for sub incomers in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. withthe following in flush with wall with earth connection only. 168 supply and fixing of 12way single pole and neutral mcb sheet steel enclosure distribution board with double door ( metal ) 1no. 32a 30 ma 4 pole elcbas incoming and10 nos. 6a to 32a sp mcb outgoing in flush with wall. the mcb db and mcbs should be with isi mark ( like standard make ) 169 supply and laying of following xlpe armoured ltug cable in a trench / tray with suitable cable tie tag etc as required. 170 supply and laying of 3 1 / 2 x 70 sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 171 supply and laying of 31 / 2 x 35sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 172 supply and laying of 31 / 2 x 25sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 173 supply and laying of 4c x 16 sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 174 supply and clamping of following xlpe armoured ltug cable on post or on wall ms clamps , saddles, plugs, screws etc., as required. 175 supply and clamping of 3 1 / 2 core x 70 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 176 supply and clamping of 3 1 / 2 core x 35 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 177 supply and clamping of 3 1 / 2 core x 25 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 178 supply and clamping of 4c x 16 sq.mm pvc armoured ltugaluminium cable on post or on wall with ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 179 supply and fixing of double compression brass cable gland for following aluminium conductorxlpe insulatedarmoured cable of 1100 v grade with earth connection. 180 supply and fixing of brass cable gland for3 1 / 2 cx 70 sq.mm pvc ltugarmoured cable with earth connection 181 supply and fixing of brass cable gland for3 1 / 2 cx 35 sq.mm pvc ltugarmoured cable with earth connection 182 supply and fixing of brass cable gland for3 1 / 2 cx 25 sq.mm pvc ltugarmoured cable with earth connection 183 supply and fixing of brass cable gland suitable for4c x 16 pvc armoured ltug cable with earth connection. 184 supply and providing cable end termination of the following sizepvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete ( copper sockets for copper cables and alu. sockets for alum. cable ) 185 supply and providing cable end termination of 3 1 / 2corex 70 sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 186 supply and providing cable end termination of 3 1 / 2corex 35sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 187 supply and providing cable end termination of3 1 / 2corex 25sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 188 supply and providing cable end termination of 4 c x 16sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete. 189 wiring with 2 x1.5 sq.mm. ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor of 1100 v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories with module gi switch box in flush with wall with 6a one way module switch with module front plate continuous earth wire connection by 1.0 sq.mm. pvc insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour for concealed pvc light point / fan point ( for electronic regulator ) ( 4points / coil ) higher end 190 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling withmodule gi switch box in flush with wall with 6a one way module switch with module front plate continuous earth wire connection by 1 sq.mm. pvc insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour for pvc concealed light ( 6 points per coil ) ( for rooms like bath, toilet & pumproom, etc. ) . 191 wiring with2rx1.5sqmm ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100vpvcconduit pipeconcealed wall and ceilingwith pvcaccessoriesgi metal back box and 6a modularswitch & 6a modular socket ( board itself point ) in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, for making good of the concealed portion with suitable colour for pvc concealed point ( 8 points / coil ) 192 supply, run, testing and commissioning of2 run x 2.5 sqmm and 1r of 1.5sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 193 supply and run of 50mm dia.hdpe pipe of 4kgf / cm2 approved quality and best variety conforming to iss and isi markbelow ground inhdpe pipes 194 supply and installationof 16m high mast shaft in two sections suitable for 50 m / sec wind speed, with head frame, winch mounting bracket, luminaries carriage suitable to install 8 nos of 150w led light fittings luminaries ( semi circle arrangement ) with counter weight arrangements , mounting clamp and brackets etc. raising , lowering system comprising double drum winch, suitable ss wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lighting finial, lightning spike if require, wiring material from jb to individual luminaire & mcb in base compartment are included and are a part of installation, foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. 150w led single light fitting dome aviation obstruction light, outdoor stand mounted feeder pillar with 63a 4pole rccb with 100ma, single dial time switch, 45a tp contactor for the automatic switching of luminaries , power tool control with 2 no 9a contactors and raise lower push button, incoming 35 sq. mm and outgoing 25& 4.0 sq. mm terminals, shallow foundation with m25 grade concrete for the high mast considering the safe soil bearing capacity at site as 10 t / sqmtr at 2 metre depth with all materials and labour, gi pipe earthing for high mast with 2.5 m long 40mm die gi pipe including connection to high mast earth terminal with 25 x 3 mm gi flats with all materials and labour ( 2nos per mast required ) , wiring of luminaires with all wiring materials like pvc insulated pvc sheathed flexible cable of suitable copper conductor cores of 2.5 sq. mm, lugs, mcb and all labour, mast feeder pillar by grouting the stand in concrete. with allnecessary components for the complete functional operation. contractor to getstructural approval from the civil team for the high mast foundation 195 supply and fixing of 150 mm dia. gi pipe ( class b ) of 9 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 10a sp mcb , 2 / 4way connector on suitable hyleg sheet and with supply and fixing of unique modular 250w led floodlight made up of pressure die cast aluminium housing with toughened glass and high power leds and secondary lenses with ip66 protection. available in nb / mb / wb angles. 10kv spd included, system efficacy = 110 / 120 / 135 suitable to operate in 120 280 v ac, 50 / 60 hz complete with suitable ms brackets for 200w led floodlight fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour. crompton cfs 501 300 57 60d hl3 gl nbkg 196 supply and fixing of 65 mm dia. ( 2 1 / 2 ) gi pipe ( class b ) of 6 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 10a sp mcb , 2 / 4way connector on suitable hylem sheet and with supply and fixing of floodlight luminaire with superior polycarbonate optics pressure die cast housing, ip66 ingress protection, 4kv in built and 10kv external surge protection. efficacy 110lm / w. available in nb / mb / wb angles. complete with suitable ms brackets for 200w led floodlight fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour. ( sd 543 ) . ( bajaj gleam f 220l wh sy pc sd v2 ) 197 supply and fixing of 65 mm dia. ( 2 1 / 2 ) gi pipe ( class b ) of 4 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 6a sp mcb switch, 2 / 4 way connector on suitable hylem sheet and supply and fixing of 45w led toplight fitting with led ( higher end ) with 1 metre 32mm dia. gi pipe ( class b ) complete with suitable ms clamps for led street light fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour ( sd 541 ) ( 45w led top light fittings 198 supply, installation, testing & commissioning of 10w led bollard light fittings fitting. the light fitting should be powder coated with high pressure die cast aluminium led housing. and the led fixed on die cast aluminium heat sink for proper thermal management.and the operating voltage range 140 – 270v ac, provided with open and short circuit protection and input surge voltage protection. the driver should be constant voltage constant current smps protection of fitting should be ip 66. led having 50, 000 burning hours with minimum 70% lumen maintenance and power factor 0.95.system consumption should be require with lumen package as per requirement. crompton cat ref : lbla3 10 cdl / equivalent ( landscape light ) . rate shall inclusive of necessary joint kit, glands, etc., for loop in / outconnection suitable to outdoor application . 199 supply and fixing of 30w led street light fitting with led ( higher end ) with 25 mm dia. gi pipe ( class b ) with 1 no. 25 mm gi bend complete on the existing post / on wall with pvc unsheathed copper leads with ms clamps and withpainting. 200 supply, installation, testing and commissioning of 18 w led down light fittingwith ip55 cool day light suitable for pole mounting, made outcrca powder coated body, aluminium reflectors, poly methyl meth acrylate ( pmma ) diffuser, glare free light, including electronic drivers, day light colour led lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive. 201 supply, installation, testing and commissioning of 40 w led tube light fitting with cool day light made out of crca powder coated body, poly methyl meth acrylate ( pmma ) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour led lamps, inter connecting wiring including accessories all inclusive. 202 supply and fixing ofpressure die cast aluminium housingbulk head 10w led fitting with ip65 protected withpvc unsheathed copper leads from terminals to the fitting. model equivalent to cromptonlbhe 10 cdl ( rate as per quotation ) ( philips / bajaj / crompton / k.lite ) 203 supply and fixing of 1200mm ( 48 ) sweep ac ceiling fan 5 star rated complete ( higher end ) with 2 module 100w fan step regulator ( higher end ) with 600mmdown rod with fan clamp, and wiring to the nearby by point with 1.5 sqmm frls , pvc insulated copper wires, including necessaryaccessories and hardwares as required. 204 supply and fixing of 300mm ( 12 ) sweep ( heavy duty ) ac exhaust fan complete with necessary wall opening and making good of the wall and wiring to the nearby by point with 1.5 sqmm frls pvc insulated copper wires including necessaryaccessories and hardwares as required. 205 supply and fixing of louvers shutters arrangements for 300mm ( 12 ) sweep ( light duty ) ac exhaust fan, including necessaryaccessories and hardwares as required. 206 supply and fixing of 1 no.16a two modulesocket , 1 no.16a one module switch with module cover plate ( plastic ) onsuitable module concealedbox ( gi ) in flush with wallwith connections. scope cover wall cutting , grouting , flushing and making good on the wall. higher end. 207 supply and fixing of 2nos.6a two module 5 pin socket , 2 nos. 6a one module switch with module cover plate ( plastic ) on suitable module concealed box ( gi ) in flush with wall with connections. scope cover wall cutting , grouting , flushing and making good on the wall. higher end. 208 earthing as per the isi specification with an earth electrode of 2.10 metre class b gi pipe of dia. not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp andwithcopper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry 209 coil earth to street light poles with no.8 swg gi wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length ( 75mm to 100mm dia. ) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth. 210 supply, fabrication, of gi / copper earth flatof following size in provided trench, clamping in wall, ceiling, with suitable clamps / saddles, connecting the joints through bracing / welding covering withtermination in the earth pits, panels, distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive 211 25 mm x 6mm gi flat ( sd 77 ) 212 no8 swg copper ( m 1571 ) 213 no8 swg gi 214 lighting rodsupply of early streamer emission air terminal ( eseat ) .model: sthe eseat has corrosion resistant stainless chrome body made up of aisi 316 grade of height 0.50 metres capable of working in hazardous atmosphere. the air terminal is non radioactive and requires no special licensing. the unit is fully autonomous ( no battery, no external power supply is required ) , collects energy from the ambient electric field. the eseat model has been tested in a high voltage laboratory in accordance with nfc 17 102 in order to measure the average gain in triggering. the average gain in triggering time ( ?ts ) obtained during the lab test for the offered model is 60 μs. the eseat works on negative as well as positively polarized discharges. eseat has been tested for such discharges in central power research institute ( cpri ) . a dedicated tester is available to test the healthiness of the eseat on request ( page no. 37, point no. 3 of clause 8.6 of the revised nfc 17 102 version 2011 ) . eseat model : s radius of protection : 46 metres level of protection considered for the project ii level 215 mounting structuresupply of standard / special mounting structure of height 4.5 mts. pipe, and 300 x 300 x 8mm ms plate, 3 mts. 48mm odclass c gi outer pipe, 1.8 mtr, 38mm od inner pipe, for roofmounting on concrete base and with frp adapter 216 down conductorsupply and run of 25mm x 6mm gi flat down conductor with necessary clamps / supports on wall / floor / ground for earthconnection 217 test linksupply of test link box for each down conductor in order to disconnect the earth termination system to enable measurement of resistance 218 supply and installation maintenance free gi earthing system comprising of 50mm dia. and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp 219 surge protectionsupply and installation cabinet type class 1 and 2 combined model spd to arrest surges and over voltage in the power line due to lightning switching action etc. they must be installed in the incoming mcc panel / db of the respective building in parallel to the power circuit. model: psv4 12.5 / 400tt ( 3 phase power network ) 220 first aid box complete with all first aid medicines ( m 1977 ) 221 shock treatment chart fixed in glass frame ( m 1978 ) 222 danger board as required by the electrical authorities ( m 1981 ) 223 supply and kept in position of 9 litres capacity fire buckets of 4 nos. with bucket stand as per standard specifications and as directed by the departmental officers 224 supply and fixing of carbon di oxide gas type 2 kg. capacity fire extinguisher as per new is15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the departmental officers. make: excellent / safety first / equivalen 225 cctv system 226 supply, installation, testing and commissioning of 32 channel 8 sata nvr, with 6t hard disk drive 4 nos, new logical and visualized gui design dual os design to ensure high reliability of system running, anr technology to enhance the storage reliability when the network is disconnected, configurable normal or hot spare working mode to constitute an n+1 hot spare system video input and transmission, connectable to the third party network cameras compression and recording, h.265+ compression effectively reduces the storage space by up to 75%, full channel recording at up to 12mp resolution hd video output ? hdmi1 / vga1 outputs provided ? hdmi1 video output at up to 4k ( 3840 × 2160 ) resolution storage and playback, upton 16 sata interfaces and 1 esata interface for hdd connection, support up to 10tb capacity for each hdd, smart search for efficient playback. and smart playback to improve the playback efficiency, supports vca search for fire / ship / temperature / temperature difference detection triggered video files, pos information overlay on live view and playback, pos triggered recording and alarm network & ethernet access ? hik connect for easy network management, 2 gigabit ethernet network interfaces. ( make : hikvision / dahua / sony. 227 supply of 8mp, internet protocol fixed bullet camera with following specification:?1 / 2.5 progressive scan cmos, ? 3840 × 2160 @15 fps, 2.8 / 4 mm fixed lens, 01 lux @ ( f1.2, agc on ) , 0.028 lux @ ( f2.0, agc on ) , 0 lux with ir, h.265+, h.265, h.264+, h.264, 2 behaviour analyses ( line crossing detection, intrusion detection ) ? face detection ? 120db wdr, ? blc / 3d dnr / roi, ip67 complied?on board storage built in micro sd / sdhc / sdxc card slot, up to 128 gb, ? shutter speed 1 / 3 s to 1 / 100, 000 s, ? 3 axis adjustment pan: 0° to 360°, tilt: 0° to 100°, ? rotate: 0° to 360°, 2.8 mm, ? horizontal fov: 102°, vertical fov: 53°, diagonal fov: 124°, ?lens mount m12 ? ir range i5: up to 50 m, ? image settings rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ? power consumption and current 12 vdc, 0.7 a, max. 7.5w poe: ( 802.3af, 36v to 57v ) , 0.3 a to 0.2 a, max. 9w 228 ? camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. ( make: dahua / panasonic ) ( rate as per quotation enclosed ) 229 supply, installation, testing and commissioning of 55 smart led tv with following specifications a ) full hd 1920 x1080 ( 4k monitor ) b ) ips panel c ) slim back light led module d ) 900 pmi e ) triple xd engine f ) dynamic scanning g ) anrh ) true colour generatori ) 8modes of picture j ) picture wizardiii k ) real cinema 24p l ) hdmi 3nos m ) usb 3nos n ) built in lan o ) magic remotep ) dimension 1242 x 724 x 55.1min ( 37 ) . ( make: sony / lg / samsung ) . 230 supply and fixing of outdoor4x6pvc box with 102mm x 77mm x 102mm with all fixing accessories. 231 supply and clamping of cat 6 armoured cable in suitable pvcpipe 1 thick on wall / ceiling with connected pvc accessories with clamps, saddles etc., complete. ( between ethernet switch to camera and radio modem ) i. application : primary ( campus ) , secondary ( riser ) , tertiary ( horizontal ) ieee 802.3 : 10base t; 100base t; 1000base tieee 802.5 16 mb; isdn; tpddi; atmii. standards: iso / iec 11801 2nd ed.; iec 61156 5 2nd en 50173 1; en 50288 6 1, eia / tia 568c.2, rohs compliant.fire rating: pvc : iec 60332 1.iii. conductor bare copper wireiv. insulation polyethylene v. twisting 2 cores to the pair vi. cable lay up 4 core to the pair it has diameter of ( 23 awg ) 0.550 ± 0.015.insulation : polyethylene.gi wire of size is 0.90 ± 0.030mm. 232 fixing and termination of cat 6 cable rj 45jack single point ( point to point ) crimping, testing and arrangement charges. 233 supply, run, testing and commissioning of2 run x 2.5 sqmm and 1r of 1.5sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 234 supply and fixing of poe 24 port switch10 / 100 / 1000 base t / 2 x 1000base fx / 20gbps bandwidth / ieee803.af / at compliant poe+ / rj45 supports auto mdi / mdi x function / auto negotiation speed, half / full duplex / store and forward / max packet size: 10kbytes / wide range power design ( 12~56vdc ) / operating temperature ( 40 °c ~ +75 °c ) / reverse polarity protection / resettable fuse to protect against overcurrent / ip 40 protection / eft protection for power line. 235 supply and fixing of poe 8 port switch10 / 100 / 1000 base t / 2 x 1000base fx / 20gbps bandwidth / ieee803.af / at compliant poe+ / rj45 supports auto mdi / mdi x function / auto negotiation speed, half / full duplex / store and forward / max packet size: 10kbytes / wide range power design ( 12~56vdc ) / operating temperature ( 40 °c ~ +75 °c ) / reverse polarity protection / resettable fuse to protect against overcurrent / ip 40 protection / eft protection for power line. ( make: dlink, netgear / tplink ) 236 supply and fixing of out door weather proof box 2ft x 2ft out door weather proof box 2ft x 2ft 237 supply and fixing of rack with accessories higher end 42 u rack with lns unit and fan extra for the above rack. 238 supply and fixing of 2 feet cctv camera stand with attachment fittings as follows:* weather heads and couplings * cabinet mounting fittings, plates, brackets as needed. * reinforced couplings for wire entrances to cabinets. 239 supply and installation for 2kva ups with battery, single phase ups ( single phase in & single phase out ) capacity system with battery 2hours back up 240 supply and installation for 1kva ups with battery, single phase ups ( single phase in & single phase out ) capacity system with battery 1 hours back up 241 of 6mlengthpole with base plate of size 250x250x6mm as per is 875 with following specification. pole outer die 76.10mm x 3.65mm thick x 6 meter. 242 supply and filling in foundation and basement with m sand / filling sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification. 243 providing and relaying plain cement concrete 1:2:4 ( one cement two sand and ten broken machine crushed stone jelly ) using hbg machine crushed stone jelly of size 20mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. 244 pa system 245 supply, installation, testing & commissioning of 30 watts 2 way high efficiency, high fidelity, long throw ip65 weather proof p.a music horn speaker. it combines the high efficiency of horn with wide frequency response. music horn is weather protected and uv protected abs plastic housing combines with the feature of easy poertap selection on a terminal strip with a two core cable. it has impedance of 250 / 500 / 1k / 2k ohm with frequency response of 120 16000 hertz. ( make: ahujaamh402t / bosch or its equivalent ) 246 supply, installation, testing & commissioning of 240 watts p.a mixer amplifier with the output power of 1350 watts maximum, 500watt rms at 10% thyristor harmonic distortion ( thd ) , 850watt rms at 5% thd, 800 wattsrms at 2% thd and the power supply ac voltage ranging from 220 240 volt, 50 / 60 hertz. with the dc input of 48 volt and 1000watts has tone controls of bass=+ 10 db at 100 hz weighing 42kg with the speaker output of2q, 4q.70volt&100volt has power consumption of 1600va ac &12a dc and 100db output regulation at 1khz no load to full load ratio. the signal to noise ratio is 60db with the input channels of 0.8mv / 4.7kq, 3*aux 100mv / 50kq.the frequency response of 50 15000hz+ 3db. ( make: ahuja ssa 10000 / bosch or its equivalent ) 247 supply, installation, testing & commissioning of10 gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedance and has 2.5mv / pa sensitivity and frequency response ranging from 50 15000hz with multi tone chime model. ( make: acm66 ahuja / bosch / its equivalent ) 248 supplyand run ofarmoured speaker cable 2 core 2.5 sqmm and 1r of 1sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 249 supply & installation of custom built m.s powder coated wall mounting audio rack with lock & key for housing of amplifier & player / recorder conforms to eia 310, iec 60297 and able to withstand the load of 40kg with welded construction made up of crca steel with suitable height, width and depth. 250 supply, installation, testing & commissioning ofcordless mic uhf model. ( make: acm66 ahuja / bosch / its equivalent ) 251 maintenance of garden for a period of six months including all required materials and man power etc., all inclusive....
Due Date : October 25, 2023
Tender Value : ₹ Ref. Documents
