base plate Tenders in Tamil Nadu

7
Rural Development And Panchayats Department - Tamil Nadu

40858044 improvements of basic amenities to sc habitation in perumperkandigai panchayat in acharapakkam panchayat union in chengalpattu district under pmagy 2022 23 , part i:construction of 30000 ltr oht in perumperkandigai villageat perumperkandigai panchayat in acharapakkam panchayat union.est.amount .rs.17, 50, 000 / , earth work excavation & depositing on bankwith an initial lead of 10 metre & initial lift of 2 metre in hard shift clay, stiff block cotton, hard red earth shales, murrum, gravel, stoney earth, and earth mixed with small size boulders and hard gravelly soil ( ss 20b ) for foundation including shoring, strutting, baling out water providing danger light wherever necessarydepositing thesurplus earth on bank and otherincedential charges etc., complete and as directed by twad board officers , first depth of 4m from 0 to 4 m below gl , msand filling for foundation including cost of sand, watering, ramming andconsolidation etc complete as directed by twad bord officers , plain cement concrete 1:4:8 ( one cement, four sand and eight hard granite broken stone of 40mm size iss gauge ) forfoundation and footing including mixing, placing, ramming , finishing curing etc. complete in accordance with standard specification and as directed by the twad board officers. , reinforced cement concrete mix m30 grade using 10mm & 20mm hard blue granite broken stone ( machine crushed ) excluding the cost of rts rods for reinforcement and centering, strutting, shutteringbut including cost of all materialsmixing, laying, vibrating the concrete with mechanical vibrators, ramming, consolidating, finishing and curing etc., complete and as directed by the twad board officers. , below 1.5m from gl , 0m to 1.50m below gl , 0m to 4.50m above gl , 4.50 m to 7.32 m above gl , 7.32 m to 10.98 m above gl , 10.98 m to 14.64 m above gl , 14.64 m to 18.30 m above gl , supply and erection of steel centering, shuttering for soffits and sides including necessary supports and strutting for all rcc works using ms sheets of suitable size of bg10 stiffened with ms angle of size 25 x 25 x 3 mm for boarding laid over i type ms truss of size 25 x 25 x 3mm about 90cm c / c and supported by 40mm gi pipes ( medium ) spaced at 75cm c / c etc complete and as directed by the twad board officers. , plain surface , below gl , from gl to 3.30m , from 5.30m to 6.30m above gl , from 8.30m to 9.30m above gl , from 11.30m to 12.30m , square column: , square column below gl and upto 3.30m above gl , 3.31m to 4.30m ht , 4.31m to 5.30m ht , 5.31m to 6.30m ht , 6.31m to 7.30m ht , 7.31m to 8.30m ht , 8.31m to 9.30m ht , 9.31m to 10.30m ht , 10.31m to 11.30m ht , 11.31m to 12.30m ht , curved surface upto 3.30m ht. , 11.30m to 12.30m , 12.30m to 13.30m , 13.30m to 14.30m , 14.30m to 15.30m , supplying, cutting, bending, tying, fabricating and placing in position of steel rods for all rcc works including cost of steel and binding wire etc. ( the steel should conform to the relevant isspecificationand supplied with test certificatefe. 415 grade as per is specification no.1786 / 1985 and as amended from time to time ) delivery at site of work including loading, freight, unloading, stacking, transit insurance charges, taxes etc. complete.and as directed by the twad board officers. , painting two coats with approved plastic emulsion over one priming coat of white cementover cement plastered wall surface and ceiling including cleaning preparing the surface and curing etc., complete ( using cement paint of colour as approved by the departmental officer ) and as directed by the twad board officers. , fabrication, supply, delivery and fixing of outside ms ladder of 45cmclear wide made out of 50 mm x 50mm x 6mm ms angle for both sides and for steps at 30cm c / c welded jointed etc ., for i staging from gl to 1st level brace ( weight 4.5kg / m ) iind and iiird staging upto floor slab and ivth staging from floor slab to roof top. supply, delivery and fixing of 32 mm gi pipes medium for hand rails from i stage to ivth stage. rcc m30 grade mix for landing slab 5 nos. at ground level 1no. and above ground level 4nos. supply and fixing of 32mm gi pipe medium for hand rails for the landing slab. supplying and fixing of ms base plate of 100mm x 100mm x 6mm thick for fixing anchore fastener bolt for fixing of hand rails at landing slab and ms ladder providing locking arrangements with two coats of approved enamel paint over one coat of red oxide paint as per approved type design and as directed by twad board officers. , providing and fixing of rcc inner access ladder in rcc 1:11 / 2 :3 ( one cement, one and half sand and three aggregate ) using 20mm hbg stone for oht including cost of reinforcement, placing grill in position, centring, shuttering charges, mixing concrete, curing etc. to required height and clear width of 45 cm consisting of 2 nos. of vertical post of 10 cm x 15 cm and step slab of 25mm x 25mm etc.complete and as directed by twad board officers. , providing 110mm pvc vent cowlarrangementsmosquito proof nylon net and as directed by twad board officers , supply and fixing of cut stone of size 0.30m x 0.30m x 0.15m in cm 1;3 ( one cement and three sand ) below inlet pipe for service reservoir as directed by twad board officers. , providing manhole cover of size 0.60 x 0.60m in rcc 1:1.5:3 with suitable reinforcement and 50x50x6mm ms angle fixed along edges and as directed by twad board officers , providing hand rails over the roof slab by using 32 mm gi pipe with 40mm x 6mm ms flat and fixied with 12mm dia fastner bolt 75mm long and as directed . , pipe connection arrangements for inlet, outlet, scour and overflow etc. including cost of pipes, specials, valve, labour charges for lifting, aligning, cutting, threading, fixing and painting of gi pipes with two coats of approved quality enamal paint etc. complete as detailed below. , 65mm gi pipes for inlet connection , 65mm gi pipes for over flow & rain water harvesting pipe , 50mm gi pipes for scour pipe , 65mm gi pipe for delivery pipe , 90mm pvc threaded coupler , 63mm pvc threaded coupler , 65mm dia gi tee , 65mm dia gi bend 90 , 65mm dia gi bend ( short ) , 65mm gi coupler , 65mm gi union , 65mm gi elbow , 50mm gi union , 50mm gi elbow , 65mm gi tee , 65x50mm gi reducer , 75mmx63mm pvc reducer , 65mm gm gate valve , 50mm gm gate valve , earth work excavation in all types of soil lead and lift ss 20 b etc complete including all labour charges including cost and conveyance etc complete. . , supply and following of 90mm pvcpipe includingcost and conveyance etc complete. ( 6ksc ) , laying and fixing of 90mmpvcpipe includingcost and conveyance etc complete. , refilling excavated earthincluding all labour charges including cost and conveyance etc complete. . , part ii:providingpumping main pipe line to perumperkandigai colony at perumperkandigaipanchayat in acharapakkam panchayat union block. estimate amount : rs.2, 50, 000 , earth work excavation in all types of soil lead and lift ss 20 b etc complete including all labour charges including cost and conveyance etc complete. . , supply and following of 90mm pvcpipe includingcost and conveyance etc complete. ( 6ksc ) , laying and fixing of 90mmpvcpipe includingcost and conveyance etc complete. , refilling excavated earthincluding all labour charges including cost and conveyance etc complete. . , gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : December 05, 2023

Tender Value : ₹ 20 Lakhs

View Tender
9
Town Panchayats - Tamil Nadu

40855273 tender for rejuvenation of bund to ayyan kulam in ammapettai town panchayat.; 1 earth work excavation for foundation, septic tank etc., in all soil sand sub soils ( vide sl no.506+62 ) and to full depth as may be directed except in hard rock requiring blasting inclusive of stoning, shuttering, bailing out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15cm thick well rammed and depositing the surplus earth with in the compound in place shown by the departmental officers within an initial lead and lift and clearing and leveling the site etc., completed 2 foundation 3 plain cement concrete 1:4:8 ( one cement , four m sand , eight aggregate ) mix using 40mm iss hbg stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15 cm thick and well rammed and compacted , etc., completed complying with standard specification. 4 centering for soffits of rcc slabs of plane surface like lintels, beams , etc., including strutting 3m high using mild steel sheets of size 90cm x60cm x and b.g 10 stiffened with m.s angles of size 25mm x 25mm x 3mm laid over silver oak ( c.w ) joists of size 10cm x 6.5cm ( spaced at about 90cm c / c ) and supported dy casurina props of 10cm to 13cm dia ( spaced of 75cm c / c ) complying with standard specification and directedgrade beam 5 with strutting 6 plain cement concrete 1:2:4 ( one cement, two fine aggregates and four coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification 7 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete with extra lead for conveyance etc, complete. 8 providing and laying, spreading and compacting graded stone aggregate to wet mix macadam ( wmm ) specification including premixing the material with water at omc in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of morth specifications. 9 supplying and laying rubberised interlocking paver blockm40 grade providing and laying of63mmthick high strength type conforming is 15658 2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 10 supplying and fixing gi.pipe 32mm dia ( b class ) including cutting and fixing in suitable concrete and providing weld mesh of size 750 x500mm size 90 gauge and providing m.s. flat 35x6mm size at middle angle allowed of sizeluding cost and conveyance and welding with weld mesh. 25x25x5mm including cost and conveyance and welding with weld mesh. 11 supply and installationof led based street light luminaire made up of extured alluminium alloy body sealed toughened glass protector and pc side covers. the optical and control gear compartment should be with ip66 tightness leds in natural white ( 4000 4 ) 25w led street light 12 supply and fixing of 2x 1.5 sq.mm copper cable from pole switching point to light fittings 13 supply and fixing of light post 4m length single bracket pole with base plate ( 250 x 250 x 6mm ) 76.10mm od x 3.65mm thick x 4000mm length including fiber connection junction box internal wiring works on each pole including cost and conveyance etc complete. 14 collection, supply and filling of stone dust of approved quarry including cost and conveyance of al materials to site and all labour charges for filling etc complete. 15 providing and laying in position, standardised concrete mix m 20 grade in accordance with is:456 2000, using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg / m? and maximum water cement ratio of 0.55, including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5 cu.m. ) 7730 kg. of 20mm machine crushed stone jelly and with about ( 3.3 cu.m. ) 5156 kg. of 10 12mm machine crushed stone jelly and with about ( 4.79 cu.m. ) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.the coarse and fine aggregates to be used should comply with the requirements of is standards. ( no separate payment will be made by the department for the excess usage of materials ) . 16 suppling and fabricating and placing in position ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors. including charges for cutting, straightening, and bending, typing, welding, jointing, over laping and all labour charges etc....

Due Date : December 08, 2023

Tender Value : ₹ 57 Lakhs

View Tender
16
Southern Railway - Tamil Nadu

40833438 supply of water boiler of 30 litres capacity confirming to is: 3412 along with control box, necessary plumbing & tap arrangement on a common base plate confirming to rcf specification no. edts 118, rev. e, am 2, cor. 1, 2 & 3 without annexure 1 & drg. no. lh72211, alt. b [ warranty period: 30 months after the date of delivery ] => limited...

Due Date : December 08, 2023

Tender Value : ₹ Ref. Documents

View Tender
17
Rural Development And Panchayats Department - Tamil Nadu

40832154 tender for part 1 : construction of health sub centre building at vadakavunji, h / o vadakavunji.; 2 clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 3 earthwork excavation for foundation ( for narrow excavation ) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification. 4 supplying and filling in foundations and basement with fillingm sand in layers not exceeding 15 cm. thick, well watered , rammed and consolidated etc. complete complying with standard specifications. 5 plain cement concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. 6 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 7 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete. 8 supplying and erecting centering and shuttering for soffits including necessary supports and strutting up to 3 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) . 9 upto basement 10 ground floor 11 design mix concrete 12 providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of m25 grade for reinforced cement ratio with plasticizer using 20mm and down concrete structural elements under controlled water graded machine broken granite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart mental officers comple. 1m3 13 foundation & basement 14 ground floor 15 r.c.c 1:5:10 mix ( lean mix ) for column above roof level in parapet including cost and conveyance of materials and labour charges etc, complete.using m20 16 cemant concrete 1:3:6 using 40mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 17 cemant concrete 1:2:4 using 20mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 18 steel fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 19 brick work in following cement mortar 1:5 using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4 for foundation and basement including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the engineer in charge. 20 foundation basement 21 ground floor 22 brick partition walls of 11.50cm thickness using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) . 23 groundfloor 24 plastering work 25 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor slabs, beams, and sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the enineer in charge. this rate includes the cost of providing cement mortar beadings for sun shades, steps, landing slabs, elevation etc. complete complying with standard specifications. 26 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 27 flooring and dadooing 28 paving the floor with best quality vertified tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.776 / sq.m 29 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.464 / sq.m 30 dadoodling the walls with colored glazed tiles approved size, quality and color set in cm 1:2 10 mm thick. and pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 kg / sqm etc. complete. basic cost rs.318 / sq.m 31 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) . 32 providing, fabricating and fixing m.s. grillswindows, and ventilator, gates, ladders, rail pipes, nosing angles, with m.s.lugs in staircase steps etc., made out of m.s rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the engineer. 33 s.s handrail 34 manufacturing, supplying and fixing of stainless steel handrails for staircase using 50mm dia 304l grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete.the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, ect.complete. 35 supply and fabrication of upvc doorincluding cost and conveyance of all charges etc complete. 36 solid pvc door shutters toilet door using 19 gauge 19mm ms square tubes for styles and outer frames.15mm ms square tubes for top, lock and bottom rails.the steel tubes shall be covered with 5mm thick solid pvc sheets.shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.the over all size of styles shall be 50mm x 30mm.the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.the over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. 37 upvc windowsupplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g / 1mm 125gsmand 100% corrosion free, the profiles are multi chambered sectionwith wall thick of 2mm. the epdm rubber ( black color ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power points locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed or plainglass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and shouldhave key lockable action, security protective hinges, strong lockingsystems and as per sizefor arrestingnoise and energy loss. 38 upvc ventilator: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with gi / 1mm 125gsmand 100% corrosion free , the profile are multi chambered sections withwall thick of 2mm. the epdm rubber ( black color ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. the ventilator should be got approved from the executive engineer before use on work. 39 painting work 40 painting two coats of synthetic enamel paint of approved colour and make over one coat of anti corrosive zinchromite primerover new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications. 41 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 42 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 43 weathering course concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( no sand to be used ( over the rcc roof slab in the proportion of brick jelly to lime being 32 : 121 / 2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed 44 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. 45 earthwork for foundationsand depositing on bank with initial lead of 10 mt. and initial lift of 2 mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soilincluding excavated earth. 46 laying the plain cement concrete 1:4:8 ( one cement four sand and eight brokenmachine crushed stone jelly ) using hbg machine creased machine crushed stone jelly of size 40mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.the rates inclusive of centering , shuttering, strutting, propping, removal of form work if it is required and all leads , lifts and curing etc.. 47 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) 48 brick work in following cement mortar using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 for foundation and basement including curing, etc., complete complying with standard specifiction. 49 reinforced cement concrete 1:1.5:3 mixusing 20mm machine crushed 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding cenetering, shuttering and cost of reinforcement grills placed in position, but including laying, vibrating, curing and finishing, fixing fan clamps in the rcc floor and roof slab works wherever necessary and bearing surfaces of the wall at the sides and bottom of the slab, beams shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers. 50 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally and externally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or champhering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent andas directed. 51 supplying and fixing in position c.i.manhole covers ( heavy duty ) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6x0.6m size etc., complete. 52 providing, machine mixing and laying on the p.c.c / r.c.c. surface in approved panels of25 mm thick granolithic flooring in cement concrete mix of 1:2:4 ( 1 cement: 2 sand: 4 aggregate 10 to 12 mm thick ) well vibrated, compacted including 45 x 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well covered and protected against excess of an type. ( the contractor to provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond and any curling, lifting or beybonding noticed shall be rectified by the contractor at his cost ) . 53 supplying, fabricating and placing in position mild steel / ribbed tor steel rods for all rcc works including cost of steel and binding wire also in all floors, complete complying with standard specfication. 54 light / fan point sd 24 55 plug point sd 38 56 concealed power plug point sd 40 57 ceiling fan sd 106 58 exhaust fan sd 114 59 4 18w crystal glass led tube light fitting 60 tneb meter board 61 service connection sd 66 62 earth connection sd 74 63 provision for name board charges 64 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : December 05, 2023

Tender Value : ₹ Ref. Documents

View Tender
18
Rural Development And Panchayats Department - Tamil Nadu

40831464 tender for 15th finance commission health sub center vilpatty kovilpatty 2023 2024 kodaikanal block of1 works tn 05 10; 1 part 1 : construction of health sub centre building at kovilpatty, h / o vilpatty. 2 clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 3 earthwork excavation for foundation ( for narrow excavation ) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification. 4 supplying and filling in foundations and basement with fillingm sand in layers not exceeding 15 cm. thick, well watered , rammed and consolidated etc. complete complying with standard specifications. 5 plain cement concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. 6 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 7 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete. 8 supplying and erecting centering and shuttering for soffits including necessary supports and strutting up to 3 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) . 9 upto basement 10 ground floor 11 design mix concrete 12 providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of m25 grade for reinforced cement ratio with plasticizer using 20mm and down concrete structural elements under controlled water graded machine broken granite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart mental officers comple. 1m3 13 foundation & basement 14 ground floor 15 r.c.c 1:5:10 mix ( lean mix ) for column above roof level in parapet including cost and conveyance of materials and labour charges etc, complete.using m20 16 cemant concrete 1:3:6 using 40mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 17 cemant concrete 1:2:4 using 20mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 18 steel fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 19 brick work in following cement mortar 1:5 using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4 for foundation and basement including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the engineer in charge. 20 foundation basement 21 ground floor 22 brick partition walls of 11.50cm thickness using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) . 23 groundfloor 24 plastering work 25 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor slabs, beams, and sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the enineer in charge. this rate includes the cost of providing cement mortar beadings for sun shades, steps, landing slabs, elevation etc. complete complying with standard specifications. 26 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 27 flooring and dadooing 28 paving the floor with best quality vertified tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.776 / sq.m 29 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.464 / sq.m 30 dadoodling the walls with colored glazed tiles approved size, quality and color set in cm 1:2 10 mm thick. and pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 kg / sqm etc. complete. basic cost rs.318 / sq.m 31 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) . 32 providing, fabricating and fixing m.s. grillswindows, and ventilator, gates, ladders, rail pipes, nosing angles, with m.s.lugs in staircase steps etc., made out of m.s rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the engineer. 33 s.s handrail 34 manufacturing, supplying and fixing of stainless steel handrails for staircase using 50mm dia 304l grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete.the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, ect.complete. 35 supply and fabrication of upvc doorincluding cost and conveyance of all charges etc complete. 36 solid pvc door shutters toilet door using 19 gauge 19mm ms square tubes for styles and outer frames.15mm ms square tubes for top, lock and bottom rails.the steel tubes shall be covered with 5mm thick solid pvc sheets.shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.the over all size of styles shall be 50mm x 30mm.the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.the over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. 37 upvc windowsupplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g / 1mm 125gsmand 100% corrosion free, the profiles are multi chambered sectionwith wall thick of 2mm. the epdm rubber ( black color ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power points locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed or plainglass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and shouldhave key lockable action, security protective hinges, strong lockingsystems and as per sizefor arrestingnoise and energy loss. 38 upvc ventilator: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with gi / 1mm 125gsmand 100% corrosion free , the profile are multi chambered sections withwall thick of 2mm. the epdm rubber ( black color ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. the ventilator should be got approved from the executive engineer before use on work. 39 painting work 40 painting two coats of synthetic enamel paint of approved colour and make over one coat of anti corrosive zinchromite primerover new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications. 41 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 42 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 43 weathering course concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( no sand to be used ( over the rcc roof slab in the proportion of brick jelly to lime being 32 : 121 / 2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed 44 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. 45 earthwork for foundationsand depositing on bank with initial lead of 10 mt. and initial lift of 2 mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soilincluding excavated earth. 46 laying the plain cement concrete 1:4:8 ( one cement four sand and eight brokenmachine crushed stone jelly ) using hbg machine creased machine crushed stone jelly of size 40mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.the rates inclusive of centering , shuttering, strutting, propping, removal of form work if it is required and all leads , lifts and curing etc.. 47 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) 48 brick work in following cement mortar using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 for foundation and basement including curing, etc., complete complying with standard specifiction. 49 reinforced cement concrete 1:1.5:3 mixusing 20mm machine crushed 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding cenetering, shuttering and cost of reinforcement grills placed in position, but including laying, vibrating, curing and finishing, fixing fan clamps in the rcc floor and roof slab works wherever necessary and bearing surfaces of the wall at the sides and bottom of the slab, beams shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers. 50 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally and externally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or champhering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent andas directed. 51 supplying and fixing in position c.i.manhole covers ( heavy duty ) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6x0.6m size etc., complete. 52 providing, machine mixing and laying on the p.c.c / r.c.c. surface in approved panels of25 mm thick granolithic flooring in cement concrete mix of 1:2:4 ( 1 cement: 2 sand: 4 aggregate 10 to 12 mm thick ) well vibrated, compacted including 45 x 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well covered and protected against excess of an type. ( the contractor to provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond and any curling, lifting or beybonding noticed shall be rectified by the contractor at his cost ) . 53 supplying, fabricating and placing in position mild steel / ribbed tor steel rods for all rcc works including cost of steel and binding wire also in all floors, complete complying with standard specfication. 54 light / fan point sd 24 55 plug point sd 38 56 concealed power plug point sd 40 57 ceiling fan sd 106 58 exhaust fan sd 114 59 4 18w crystal glass led tube light fitting 60 tneb meter board 61 service connection sd 66 62 earth connection sd 74 63 provision for name board charges 64 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : December 05, 2023

Tender Value : ₹ Ref. Documents

View Tender
19
Municipal Adminitration And Water Supply Department - Tamil Nadu

40829006 tender for construction of weekly market at ward no.3, survey no.3; 1 earth work excavation for foundation in hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders ss.20b and sand, silt or other loose soil, wet sand, or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrockrequiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc., complete 10 cum ( data ) 2 footing 3 supplying and filling in foundation andbasement with filling m sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification. data 4 refilling with excavated earth in layers of 30 cm watered well rammed and consolidatred conforming to standard specification including labour charges as directed by engineer in charge 5 supplying and filling the basement with good earth filling in layers of not more than 15cmthick well rammed watered and compacted etc., complete complying with standard specification. 6 plain cement concrete 1:4:8 ( one cement four fine aggregates and eight coarse aggregates ) using 40mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification 7 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. ( payment for centering shall be given after the concrete is laid ) 8 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 9 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 10 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 11 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg / cum and maximum water cement ratio of 0.55 including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about ( 5.0cum ) , 7730kg of 20mm machine crushed stone jelly and with about ( 3.3 cum ) , 5156kg of 10 12mm machine crushed stone jelly and with about ( 4.79cum ) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is staandards. ( no separate payment will be made by the department for the excess usage of materials ) 12 m 25 concrete providing and laying in position, standarised design mix m 25 grade using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 350kg / m3 and maximum water cement ratio of 0.55, including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5.70 cu.m. ) 940.50kg of 20mm machine crushed stone jelly and with about ( 2.80 cu.m. ) 462.00kg of 10 12mm machine crushed jelly and with about ( 4.25 cu.m. ) 701.25kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever neccessary without clambing extra, etc. complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requierments of is 383 2016. ( no separate payment will be made by the department for the exces usage of materials as per design mix. ) ( si no 81 ) 13 foundation 14 ground floor 15 suppling and fabricating and placing in position ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors. 16 brick work in cm 1:5 ( one cement & five sand ) using ii class ground moulded bricks of size 9x43 / 8x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification. 17 ground floor 18 brick partition walls using ii class ground moulded chamber bricks of size 9x43 / 8x 23 / 4in c.m 1:3using hoop iron reinforcement, if found necessary standard specification including finishing, curing, etc., complete complying with standard specification 10 sqm 19 plain cement concrete 1:2:4 ( one cement, two fine aggregates and four coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification 20 plastering with cement mortar ( 1:5 ) 12mm , thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications ( s.i.306 ) 21 plastering with cement mortar 1:3, 10 mm , thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications ( s.i.306 ) 22 painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete. 23 finishing the top of floor with granolithic finish with cc 1: 2: 4 ( one cement, two sand & four hbg jelly ) using chips of grade 10 mm andbelow for 25mm thickness and rubbed smooth etc, complete as per standard specification. 24 paving the floor with design rajasthankotta tiles ( colour and shade as directed ) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 ( one cement and three sand ) 20mm thick laid in situ and pointed with same coloured cement etc, complete as per standard specification 25 supplying and fixing in position cement basedhydrualically pressed anti skid tiles ( pattern design ) 20 mmthick in cement mortar 1:3 20mm thick & pointedwith same colour of cement etc., complete as per standard specification 26 dadooing walls withglazed tiles of sizes 305mm x200mm x 6mm size of approved make and quality and colour l set in cement mortar 1:2 ( one cement , two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed. 27 supplying & fixingdoor shutters for mediun density fiber board of exterior grade 35 mm thick, single leaf conforming to is:12406 / 1989 with 35x12 mm t.w.lipping on all edges with necessary adhesives and cp screws complying with standard specifications. the rate is inclusive ofthreee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos, 200mm towerbolt i no. 300mm aldrop 1 no. alu handle ornamental type 2 nos, and 1 no. door stopper etc complete. 28 supply and fixing of pvc solid doors using 19gauge 19mm ms sq, tubes for styles and frames, 15mm ms sq.tubes for to, lock and bottom rails. the steel tubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in positionincluding furniture and fittings. the over all size of styles shall be 50mm x 30mm. the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. the over all size of frames shall be 50mm x 45mm with suitable tabate for housing the shutter etc, complete as per standard specification. pwd sor pg. no. 48 29 upvc ventilatorspecification: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with gi / 1mm 125gsm and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiations pin headed glass 4mm thick should be provided in the louvers. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the ventilator should be got approved from the executive engineer before use on work pwd sor pg. no. 66 30 upvc windowspecification: supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 125gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work ( pwd sor pg. no. 65 ) 31 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete 32 weathering course with concrete broken brick ( s.i.no.278 ) & ( p & d ) data 54.jelly 20mm gauge in pure slaked lime ( no sand to be added ) over roof slab, the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete. 10 cum 33 manufacturing, supplying and fixing of stainless steel hand rails for staircase near wet riser using 50mm dia 304l grade stainless steel pipe of 1.60mm thick will be provided with tubular supports made of 304l grade stainless steel pipe of 25mm dia of 1.60mm thick welded to the railing. the supports will be grouted into the wall and provided with 93.00mm thick stainless steel circular base plate of 304 grade. the rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete ( pwd sor p.no :57 ) 34 supplying, fabricating, erecting structural steel work for roofing welded or bolted type using ms channels, angles, plates and round bars etc. conforming to is specification including primer coating and enamal painting as per design given by the departmental officers etc, complete as per standard specification 35 supplying and laying rubberised inter locking paver block m40 grade providing and laying of 83mm thick high strength type confirming is 15658 2006 of rubberised inter locking paver block insize of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 36 providing and laying, spreading and compacting graded stone aggregate to wet mix macadam ( wmm ) specification including premixing the material with water at omc in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of morth specifications. 37 fabricating supplying and fixing of galvalume colour sheet of size 0.47mmwith the following specification. the materials should be of ppgi tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. the sheet should be g.i.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws, plastic washer.the washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of z 120 gsm paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. the sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. 38 providing & fixing pvc rain water down fall pipe of the following dia with necessary t.w.clamps plugs, shoes, bemds, other clamps, screws nails etc., complete complying with standard specification. the rate is inclusive of cost of removable iron gratings of appropriate size. the size of teak wood plugs used is 150x25mm in front & 200x75mm in rear ( wall side ) with a depth of 110mm. the pipe is to be fixed by means of u clamps at the centre of pipes to be fixed.110mm dia pvc pipe [ 4 kg / sqcm ] ( d ) 39 supplying and fixing of 1000 litters capacity pvc tank of approved quality including cost of all materials like tank fittings, lead .lift, errection etc complete. pwd sor pgno:91 40 supplying and fixing in position first quality and approved variety of gun metal gate valve ( heavy type ) with i.s.i.mark of the following sizes including cost of shellac , thread etc, .including labour for cutting and threading of g.i.pipes etc., complete complying with standard specifications for both internal and external water supply arrangements. ( d ) 41 25mm gun metal valve 42 32mm gun metal valve 43 suppling and fixing in position15mm.diameter brass / c.p screw down tap / pillar tap ( heavy duty ) of approved make conforming to i.s.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary ( d ) 44 sd tap 45 pillar tap 46 p.v.c. pipes ( 10kg / sqcm ) supplying laying and jointing p.v.c pipes ( 10kg / sqcm ) of approved quality and best variety conforming to i.s.s & with i.s.i mark, of the following sizes including cutting , fixing to pvc specials using adhesive but excluding cost of such specials and fixing to wall with necessary teak wood plugs, pvc clamps and screws, making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessaryscaffolding charges. ( d ) 47 20mm dia pipe 48 25mm dia pipe 49 supplying pvc specials ( with working pressure 10 kg. / sq.cm. ) in water supply arrangements ( both in internal and external water supply arrangements pwd sor pg.no:99 si.no:367 50 coupler 51 25mm dia 52 32mm dia 53 elbow 54 25mm dia 55 32mm dia 56 bend 57 25mm dia 58 32mm dia 59 tee 60 25mm dia 61 32mm dia 62 end cap 63 25mm dia 64 32mm dia 65 reducer 66 25 mm x 20 mm 67 32 mm x 25 mm 68 reducer tee 69 25 mm x 20 mm 70 32 mm x 25 mm 71 reducer elbow 72 25 mm x 20 mm 73 32 mm x 25 mm 74 jet nipple 75 25mm dia 76 32mm dia 77 supplying and fixing in position pvc specials of the following dia and types of approved quality confirming to bis and providing leak proof joints including fixing to the walls and giving connection to the pvc soil stacks, dismantling the masonry or rcc works and re doing the dismantled portion to original condition etc., complete complying with standard specifications. ( the pvc specials should be got approved by the executive engineer before use on works ) . ( d ) 78 pvc elbow 79 110mm dia 80 pvc elbow with door 81 110mm dia 82 pvc tee 83 110mm dia 84 pvc tee with single door 85 110mm dia 86 supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 x 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape, 32 mm diametre c.p. waste union, 32 mm diametre p.v.c. waste pipe with rubber plug and chain, 15mm diametre g.m.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of c.i. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications ( d ) 87 supplying and fixing in position indian water closet of size 580 x 440mm, white glazed earthen ware of approved quality with p trap or s trap confirming to is:2556 part xii with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly ) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes / pvc pipes by dismandling brick masonry, reinforced cement concrete roof / floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers. 88 s / f in position of indian make white / colour glazed earthen ware lipped mouth flat back urinal of best approved quality with g.i.pipe connection to suitable length, 32mm bell mouthed p.v.c connection , 15mm dia g.m.wheel valve, fixing the urinal to the wall in positionwith necessary t.w.plugs , clamps, screws, shellac etc., including dismantling masonry if necessary and redoing the same to original condition , fixing the 15mm dia. g.i.pipe connection and wheel valve , painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. white colour 89 supplying and erecting in position of 250 liters capacity industrial model reverse osmosis water cum purifier todeliver potable water with world health organisation ( who ) standards with following accessories. ( a ) ms skid 1 no. ( b ) media 11054 no. vessel with 20 nb multiport valve ( withmedia pubble and fine sand and activated carbon filling ) set ( c ) feed pump 0.50 hp – 1 no. ( d ) vertical pump 2 9, 2.00 hp / single phase – 1 no. ( e ) membrane 40 x 40 filmtech ( or ) equilaents / osmonic ( usa ) 1 no. and membrane pressure vessel 40 x 40 1 no.& pressure gauge 2 nos. ( f ) flow meter 1 no. 20” filter with housing 1 no., low pressure switch 1 no., level switch 1 no. & necessary cpvc pipes and fittings. the system shall be provide with two panel control system with necessary stainless valves and fittings and float control etc. the rate should be inclusive of all civil works, wherever necessary to install the system in position and intact ( 250lts ) ( pwd sor pg no 72 ) 90 supplying and fixing in position white glazed european water closet of best quality and approved make with 100mm p os s trap with double flapped rigit p.v.c. seat cover with c.p. brass hinges with 12.5 litres pvc low level flushing tank with all internal fittings etc., complete complying with standard spoecifications, labor inclusive of fixing lowlevel flushing tank. 91 white ewc 92 supply and fixing of pvc. nahini / floor trap with stainless steel gratings 100 mm x 75 mm including all charges etc, complete as per standard specification. ( d ) 93 supply and fixng of tneb meter board suitable for 3 phase 100a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 1 / 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos. 100a fuse units ( 500v ) , 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 16 sq.mm pvc insulated copper wire with earth connection complet ( sd 130 ) 94 supply and laying of 3.5 x 25 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good 95 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories and with tw switch box and 5a ft switch with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) ( 4 points per coil ) ( sd 17 ) 96 upply and fixing of 5a / 15a 3 pin combined flush type wall socket with 15a flush type switch concealed in suitable ms box in flush with wall and covered with 3mm thick hylem sheet ( sd 138 ) 97 earthing as per the isi specification with an earth electrode of 2.10 metre class b gi pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry ( sd 233 ) 98 supply and fixing of 18w 4 feet led fitting with led light fitting complete with tw round blocks on ceiling with pvc unsheathed copper leads from terminals to the fitting ( sor page no.114 ) 99 supplying and erectingof 12 mtrs.mini mast tower polygonal shapes. suitable for 12 luminaries for wind speed up to 180 km / hr. as per is 875 parts 3 material cons.: bsen 10025 # mechanical components including head frame & pulley assay, winch bracket, lantern carriage ring, luminaries and c.g box mtg. arms, resting bracket guide ring, compensating disc, lightening arrestor.etc. ( each set ) # wire rope, safety wire rope, d suckle clamps, nuts and bolts. # cable with termination & distribution box. # foundation accessories. # winch assembly # power tool. mast bottom dia:415 mm. top : 150 mm, thk: 4, 3, 3 mm. motor 1.feeder pillar box comprising 100 ams fuse unit 24 hours timer 1 nos and contactor 1 nos outgoing mcb toggle switch and neutral link with internal wiring made of ms sheet and vermin proof.erection and commissioning of 20 mtr high mast on the above said concrete foundation using suitable equipments.fixing of flood light luminaries in the lantern carriage including internal wiring & using flexible copper cable complete. halonix led flood light 150w ( cw ) 12 nos ( pwd sor p.no : 151 ) ...

Due Date : December 06, 2023

Tender Value : ₹ 1.29 Crore

View Tender
20
Rural Development And Panchayats Department - Tamil Nadu

40828958 tender for 15th finance commission health sub center vadakavunji melpallam 2023 2024 kodaikanal block of1 works tn 05 09; 1 part 1 : construction of health sub centre building at melpallam, h / o.vadakavunji 2 clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 3 earthwork excavation for foundation ( for narrow excavation ) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification. 4 supplying and filling in foundations and basement with fillingm sand in layers not exceeding 15 cm. thick, well watered , rammed and consolidated etc. complete complying with standard specifications. 5 plain cement concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. 6 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 7 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete. 8 supplying and erecting centering and shuttering for soffits including necessary supports and strutting up to 3 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) . 9 upto basement 10 ground floor 11 design mix concrete 12 providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of m25 grade for reinforced cement ratio with plasticizer using 20mm and down concrete structural elements under controlled water graded machine broken granite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart mental officers comple. 1m3 13 foundation & basement 14 ground floor 15 r.c.c 1:5:10 mix ( lean mix ) for column above roof level in parapet including cost and conveyance of materials and labour charges etc, complete.using m20 16 cemant concrete 1:3:6 using 40mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 17 cemant concrete 1:2:4 using 20mm gauge hard broken stone jelly for foundation including watering necessary and laid in layers not more than 15cm thick compacting etc, 18 steel fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 19 brick work in following cement mortar 1:5 using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4 for foundation and basement including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the engineer in charge. 20 foundation basement 21 ground floor 22 brick partition walls of 11.50cm thickness using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) . 23 groundfloor 24 plastering work 25 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor slabs, beams, and sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the enineer in charge. this rate includes the cost of providing cement mortar beadings for sun shades, steps, landing slabs, elevation etc. complete complying with standard specifications. 26 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 27 flooring and dadooing 28 paving the floor with best quality vertified tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.776 / sq.m 29 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.464 / sq.m 30 dadoodling the walls with colored glazed tiles approved size, quality and color set in cm 1:2 10 mm thick. and pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 kg / sqm etc. complete. basic cost rs.318 / sq.m 31 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) . 32 providing, fabricating and fixing m.s. grillswindows, and ventilator, gates, ladders, rail pipes, nosing angles, with m.s.lugs in staircase steps etc., made out of m.s rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the engineer. 33 s.s handrail 34 manufacturing, supplying and fixing of stainless steel handrails for staircase using 50mm dia 304l grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete.the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, ect.complete. 35 supply and fabrication of upvc doorincluding cost and conveyance of all charges etc complete. 36 solid pvc door shutters toilet door using 19 gauge 19mm ms square tubes for styles and outer frames.15mm ms square tubes for top, lock and bottom rails.the steel tubes shall be covered with 5mm thick solid pvc sheets.shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.the over all size of styles shall be 50mm x 30mm.the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.the over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. 37 upvc windowsupplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g / 1mm 125gsmand 100% corrosion free, the profiles are multi chambered sectionwith wall thick of 2mm. the epdm rubber ( black color ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power points locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed or plainglass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and shouldhave key lockable action, security protective hinges, strong lockingsystems and as per sizefor arrestingnoise and energy loss. 38 upvc ventilator: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with gi / 1mm 125gsmand 100% corrosion free , the profile are multi chambered sections withwall thick of 2mm. the epdm rubber ( black color ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. the ventilator should be got approved from the executive engineer before use on work. 39 painting work 40 painting two coats of synthetic enamel paint of approved colour and make over one coat of anti corrosive zinchromite primerover new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications. 41 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 42 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 43 weathering course concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( no sand to be used ( over the rcc roof slab in the proportion of brick jelly to lime being 32 : 121 / 2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed 44 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. 45 earthwork for foundationsand depositing on bank with initial lead of 10 mt. and initial lift of 2 mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soilincluding excavated earth. 46 laying the plain cement concrete 1:4:8 ( one cement four sand and eight brokenmachine crushed stone jelly ) using hbg machine creased machine crushed stone jelly of size 40mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.the rates inclusive of centering , shuttering, strutting, propping, removal of form work if it is required and all leads , lifts and curing etc.. 47 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) 48 brick work in following cement mortar using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 for foundation and basement including curing, etc., complete complying with standard specifiction. 49 reinforced cement concrete 1:1.5:3 mixusing 20mm machine crushed 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding cenetering, shuttering and cost of reinforcement grills placed in position, but including laying, vibrating, curing and finishing, fixing fan clamps in the rcc floor and roof slab works wherever necessary and bearing surfaces of the wall at the sides and bottom of the slab, beams shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers. 50 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally and externally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or champhering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent andas directed. 51 supplying and fixing in position c.i.manhole covers ( heavy duty ) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6x0.6m size etc., complete. 52 providing, machine mixing and laying on the p.c.c / r.c.c. surface in approved panels of25 mm thick granolithic flooring in cement concrete mix of 1:2:4 ( 1 cement: 2 sand: 4 aggregate 10 to 12 mm thick ) well vibrated, compacted including 45 x 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well covered and protected against excess of an type. ( the contractor to provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond and any curling, lifting or beybonding noticed shall be rectified by the contractor at his cost ) . 53 supplying, fabricating and placing in position mild steel / ribbed tor steel rods for all rcc works including cost of steel and binding wire also in all floors, complete complying with standard specfication. 54 provision for name board charges 55 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : December 05, 2023

Tender Value : ₹ Ref. Documents

View Tender
21
Municipal Adminitration And Water Supply Department - Tamil Nadu

40828943 tender for construction of daily market ( meat and fish stall ) ; 1 earth work excavation for foundation in hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders ss.20b and sand, silt or other loose soil, wet sand, or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrockrequiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc., complete 10 cum ( data ) 2 foundation 3 plinth beam 4 supplying and filling in foundation andbasement with filling m sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification. data 5 refilling with excavated earth in layers of 30 cm watered well rammed and consolidatred conforming to standard specification including labour charges as directed by engineer in charge 6 plastering with cement mortar 1:4 ( one cement and four sand ) 20 mm thick mixed with best approved quality water proofing compound conforming to indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification. 7 supplying and providing anti termite pre construction treatment using aldrin or dealdrin or heptochlor as per relavent is 6313 ( part ii ) code including cost of all materials, labour, hore charges for t&p etc complete. 8 plain cement concrete 1:4:8 ( one cement four fine aggregates and eight coarse aggregates ) using 40mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification 9 supplying and filling the basement with good earth filling in layers of not more than 15cmthick well rammed watered and compacted etc., complete complying with standard specification. 10 plain cement concrete 1:2:4 ( one cement, two fine aggregates and four coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification 11 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. ( payment for centering shall be given after the concrete is laid ) 12 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 13 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc 14 for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 15 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg / cum and maximum water cement ratio of 0.55 including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about ( 5.0cum ) , 7730kg of 20mm machine crushed stone jelly and with about ( 3.3 cum ) , 5156kg of 10 12mm machine crushed stone jelly and with about ( 4.79cum ) 7670 kg of crushed stone sand ( m sand ) , but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers 16 foundation 17 ground floor 18 m 25 concrete providing and laying in position, standarised design mix m 25 grade using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 350kg / m3 and maximum water cement ratio of 0.55, including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5.70 cu.m. ) 940.50kg of 20mm machine crushed stone jelly and with about ( 2.80 cu.m. ) 462.00kg of 10 12mm machine crushed jelly and with about ( 4.25 cu.m. ) 701.25kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever neccessary without clambing extra, etc. complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requierments of is 383 2016. ( no separate payment will be made by the department for the exces usage of materials as per design mix. ) ( si no 81 ) 19 foundation 20 ground floor 21 suppling and fabricating and placing in position ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors. 22 brick work in cm 1:5 ( one cement & five sand ) using ii class ground moulded bricks of size 9x43 / 8x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification. 23 ground floor 24 plastering with cement mortar 1:3, 10 mm , thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications ( s.i.306 ) 25 plastering with cement mortar ( 1:5 ) 12mm , thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications ( s.i.306 ) 26 painting two coats with ready mixed plastic emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. 10 sq.m 27 painting two coats with ready mixed enamel paint over the new iron works of approved quality and colour without priming coatincluding the cost all materials etc., complete, in all floors. 28 paving the floor with design rajasthankotta tiles ( colour and shade as directed ) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 ( one cement and three sand ) 20mm thick laid in situ and pointed with same coloured cement etc, complete as per standard specification 29 providing laying the flooring withanti skid coloured ceramic tiles of sizes 305mm x305mm x 6mm size of approved make and quality and colour l set in cement mortar 1:3 ( one cement , three sand ) over 20 mm base layer plastering and pointing with white cement neatly as directed. 30 dadooing walls withglazed tiles of sizes 305mm x200mm x 6mm size of approved make and quality and colour l set in cement mortar 1:2 ( one cement , two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed. 31 supply and fixing of m.s grills with doors and windows with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specification. 32 supplying, fabricating, erecting structural steel work for roofing welded or bolted type using ms channels, angles, plates and round bars etc. conforming to is specification including primer coating and enamal painting as per design given by the departmental officers etc, complete as per standard specification 33 supplying and laying rubberised inter locking paver block m40 grade providing and laying of 63mm thick high strength type confirming is 15658 2006 of rubberised inter locking paver block insize of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 34 providing and laying, spreading and compacting graded stone aggregate to wet mix macadam ( wmm ) specification including premixing the material with water at omc in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of morth specifications. 35 supplying & fixingdoor shutters for mediun density fiber board of exterior grade 35 mm thick, single leaf conforming to is:12406 / 1989 with 35x12 mm t.w.lipping on all edges with necessary adhesives and cp screws complying with standard specifications. the rate is inclusive ofthreee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos, 200mm towerbolt i no. 300mm aldrop 1 no. alu handle ornamental type 2 nos, and 1 no. door stopper etc complete. 36 upvc ventilatorspecification: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with gi / 1mm 125gsm and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiations pin headed glass 4mm thick should be provided in the louvers. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the ventilator should be got approved from the executive engineer before use on work pwd sor pg. no. 71 sl.no.261 37 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete 38 weathering course with concrete broken brick ( s.i.no.278 ) & ( p & d ) data 54.jelly 20mm gauge in pure slaked lime ( no sand to be added ) over roof slab, the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete. 10 cum 39 fabricating supplying and fixing of pre painted polycorbonate sheets with the following specification. the materials should be of ppgi tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. the sheet should be g.i.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws, plastic washer.the washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of z 120 gsm paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. the sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. 40 supplying and erecting in position of following liters capacityindustrial model reverse osmosis water cum purifier to deliver potable water with world health organisation ( who ) standards with following accessories. ( a ) ms skid 1 no. ( b ) media 11054 no. vessel with 20 nb multiport valve ( withmedia pubble and fine sand and activated carbon filling ) set ( c ) feed pump 0.50 hp – 1 no. ( d ) vertical pump 2 9, 2.00 hp / single phase – 1 no. ( e ) membrane 40 x 40 filmtech ( or ) equilaents / osmonic ( usa ) 1 no. and membrane pressure vessel 40 x 40 1 no. & pressure gauge 2 nos. ( f ) flow meter 1 no. 20” filter with housing 1 no., lowpressure switch 1 no., levelswitch 1 no. & necessarycpvc pipes and fittings. the system shall be provide with two panel control systemwith necessary stainless valves and fittings and float controletc. the rate should be inclusive of all civil works, wherevernecessary to install the system in position and intact. ( 250 litres ) pwd sor pg no 72 ) 41 supply fixing and errection of cctv camara including cost and conveyance of all materials to site etc complete as per specification ( 5units / park ) ( pwd sor page ( 153 to 157 ) 42 cctv camera ( q ) 43 network video recorder ( pwd sor pg.no :165 ) 44 hard disc for nvr 4tb ( pwd sor pg.no :166 ) 45 24 port patch panel ( pwd sor pg.no :166 ) 46 rack with accesssories 4u ( pwd sor pg.no :166 ) 47 armoured lan & cctv cable ( cat 6 ) ( pwd sor pg.no 164 ) 48 29 led tv for display ( q ) 49 supply and fixng of tneb meter board suitable for 3 phase 100a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 1 / 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos. 100a fuse units ( 500v ) , 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 16 sq.mm pvc insulated copper wire with earth connection complet ( sd 130 ) 50 3.5 core 25 sq.mm. pvc armoured ltug cable ( sd 204 ) 51 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories and with tw switch box and 5a ft switch with painting of suitable colour for open pvc light point / fan point ( for electronic regulator ) ( 4 points per coil ) ( sd 17 ) 52 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with suitable tw box in flush with wall to house the control switch regulator and covered with 3mm thick hylem sheet with painting of suitable colour with continuous earth connection of 14 swg tc wire for open pvc fan point ( for rheostatic type fan regulator ) sd ( 34 ) 53 supply and fixing of 6a 3 pin flush type wall socket with 6a flush type switch concealed in suitable ms box in flush with wall and covered with 3 mm thick hylem sheet ( sd 138 ) 54 supply and fixing of 5a 3 pin and 2 pin combined flush type wall socket with 5a flush type switch concealed insuitable ms box in flush with wall and concealed with 3mm thick hylem sheet sd ( 135 ) 55 supply and run of 2 of no.8 swg gi wire for guarding with cradle with no.8 swg gi wire at the equal interval of 1.5metre sd ( 75 ) 56 supplying and fixing mcb isolator 32a tp with earth connection ( legrand ( mds / hager ( l & t make ) ( pwd sor p.no :143 ) 57 earthing as per the isi specification with an earth electrode of 2.10 metre class b gi pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry ( sd233 ) body earth 58 supply and fixing of 18w 4 feet led fitting with led light fitting complete with tw round blocks on ceiling with pvc unsheathed copper leads from terminals to the fitting ( sor page no.121 ) 59 supply and fixing of 18w led 3000k square type resessed fiiitng ( philips / havells ) complete with t.w round blocks on wall or ceiling with flu tube with pvc unsheather copper leads from terminals to the filling ( pwd sor p.no : 121 ) 60 supply and fixing of 18w led 3000k roundtype resessed fiiitng ( philips / havells ) complete with t.w round blocks on wall or ceiling with flu tube with pvc unsheather copper leads from terminals to the filling ( pwd sor p.no : 121 ) 61 9 metre length single bracket pole with base plate ( 300 x 300 x 6mm ) 114.30mm od x 5.40mm thick x 5000mm length, 88.90mm od x 4.85mm thick x 2000mm length, 76.10mm od x 3.25mm thick x 2000mm length pwd sor p.no 160 62 supply and fixing of 60w led street light fitting with led ( philips / havells ) complete pwd sor p.no 122 63 supplying and erectingof 12 mtrs.mini mast tower polygonal shapes. suitable for 12 luminaries for wind speed up to 180 km / hr. as per is 875 parts 3 material cons.: bsen 10025 # mechanical components including head frame & pulley assay, winch bracket, lantern carriage ring, luminaries and c.g box mtg. arms, resting bracket guide ring, compensating disc, lightening arrestor.etc. ( each set ) # wire rope, safety wire rope, d suckle clamps, nuts and bolts. # cable with termination & distribution box. # foundation a0.45essories. # winch assembly # power tool. mast bottom dia:415 mm. top : 150 mm, thk: 4, 3, 3 mm. motor 1.feeder pillar box comprising 100 ams fuse unit 24 hours timer 1 nos and contactor 1 nos outgoing mcb toggle switch and neutral link with internal wiring made of ms sheet and vermin proof.erection and commissioning of 20 mtr high mast on the above said concrete foundation using suitable equipments.fixing of flood light luminaries in the lantern carriage including internal wiring & using flexible copper cable complete. halonix led flood light 150w ( cw ) 12 nos ( pwd sor p.no : 161 ) 64 providing rain water harvesting using 3 nos.of rcc well rings of 90cm inner dia ( clear ) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia ms rod vertically and 3 nos. of 6mm dia ms rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia toa depth of 1m, supplying and filling 40mm hbg inside the erected well ring to a depth of 90cm, and top covered with rcc circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm m.s reinforcement at 15 cm spacings on both directions and one 6mm m.s rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the departmneal officers etc., complete in all respects. 65 supply and delivery of electric monoset centrifugal pump conforming to is 9079:2002 as amended from time to time, with ci fg 200 casing , hydraulically and dynamically balanced bronze grade ltb 2 impeller, impeller ring and casing ring, stainless steel shaft capable of discharging required quantity of water against a total head noted below due to all causes. pump shall of bee 3 star rated and capable of discharging the specified quantity at the head noted at the minimum npsha at site conditions. the shut off head shall be atleast 25% over and above the head at duty point. the pump shall be suitable for operation in ac three phase , 415 v+ / 10% , 50 hz + / 5%. squirrel cage induction motor for continuous operation. the speed of the pump and motor shall be not less than 2700 to 2900 rpm respectively. 500x20lpm ( twad sor p.no:95 ) 66 providing & fixing pvc rain water down fall pipe of the following dia with necessary t.w.clamps plugs, shoes, bemds, other clamps, screws nails etc., complete complying with standard specification. the rate is inclusive of cost of removable iron gratings of appropriate size. the size of teak wood plugs used is 150x25mm in front & 200x75mm in rear ( wall side ) with a depth of 110mm. the pipe is to be fixed by means of u clamps at the centre of pipes to be fixed.110mm dia pvc pipe [ 4 kg / sqcm ] ( d ) 67 supplying and fixing of 1000 litters capacity pvc tank of approved quality including cost of all materials like tank fittings, lead .lift, errection etc complete. pwd sor pgno:93 68 supplying and fixing in position first quality and approved variety of gun metal gate valve ( heavy type ) with i.s.i.mark of the following sizes including cost of shellac , thread etc, .including labour for cutting and threading of g.i.pipes etc., complete complying with standard specifications for both internal and external water supply arrangements. ( d ) 69 25mm gun metal valve 70 32mm gun metal valve 71 suppling and fixing in position15mm.diameter brass / c.p screw down tap / pillar tap ( heavy duty ) of approved make conforming to i.s.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary ( d ) 72 sd tap 73 pillar tap 74 p.v.c. pipes ( 10kg / sqcm ) supplying laying and jointing p.v.c pipes ( 10kg / sqcm ) of approved quality and best variety conforming to i.s.s & with i.s.i mark, of the following sizes including cutting , fixing to pvc specials using adhesive but excluding cost of such specials and fixing to wall with necessary teak wood plugs, pvc clamps and screws, making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessaryscaffolding charges. ( d ) 75 20mm dia pipe 76 25mm dia pipe 77 supplying pvc specials ( with working pressure 10 kg. / sq.cm. ) in water supply arrangements ( both in internal and external water supply arrangements pwd sor pg.no:99 si.no:367 78 coupler 79 25mm dia 80 32mm dia 81 elbow 82 25mm dia 83 32mm dia 84 bend 85 25mm dia 86 32mm dia 87 tee 88 25mm dia 89 32mm dia 90 end cap 91 25mm dia 92 32mm dia 93 reducer 94 25mm dia 95 32mm dia 96 reducer tee 97 25mm dia 98 32mm dia 99 reducer elbow 100 25mm dia 101 32mm dia 102 jet nipple 103 25mm dia 104 32mm dia 105 supplying and fixing in position pvc specials of the following dia and types of approved quality confirming to bis and providing leak proof joints including fixing to the walls and giving connection to the pvc soil stacks, dismantling the masonry or rcc works and re doing the dismantled portion to original condition etc., complete complying with standard specifications. ( the pvc specials should be got approved by the executive engineer before use on works ) . ( d ) 106 pvc elbow 107 110mm dia 108 pvc elbow with door 109 110mm dia 110 pvc tee 111 110mm dia 112 pvc tee with single door 113 110mm dia 114 supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 x 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape, 32 mm diametre c.p. waste union, 32 mm diametre p.v.c. waste pipe with rubber plug and chain, 15mm diametre g.m.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of c.i. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications ( d ) 115 s / f in position of indian make white / colour glazed earthen ware lipped mouth flat back urinal of best approved quality with g.i.pipe connection to suitable length, 32mm bell mouthed p.v.c connection , 15mm dia g.m.wheel valve, fixing the urinal to the wall in positionwith necessary t.w.plugs , clamps, screws, shellac etc., including dismantling masonry if necessary and redoing the same to original condition , fixing the 15mm dia. g.i.pipe connection and wheel valve , painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. white colour 116 supplying and fixing in position white glazed european water closet of best quality and approved make with 100mm p os s trap with double flapped rigit p.v.c. seat cover with c.p. brass hinges with 12.5 litres pvc low level flushing tank with all internal fittings etc., complete complying with standard spoecifications, labor inclusive of fixing lowlevel flushing tank. ( d ) 117 white ewc 118 supply and fixing of pvc. nahini / floor trap with stainless steel gratings 100 mm x 75 mm including all charges etc, complete as per standard specification. ( d ) 119 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete ( pwd sor 2020 2021, p.no 62 ) ...

Due Date : December 06, 2023

Tender Value : ₹ 2.59 Crore

View Tender
22
Town Panchayats - Tamil Nadu

40821682 supply and fixing of 90 w led street light fitting with 8metre single bracket pole in 28 places in ponnampatti town panchayatthiruchirappalli district. , supply and fixing of 90 w led street light: supply and fixing of 90 w led street light fitting in thesystem made of pressure die cast aluminium housing with heat resistant toughened glass cover confirming to ip65. separate compartment for leds & electronic driver with cct of 5700k, pf >0.90 system efficacy>85 . operating voltage range of 120v to 270v with surge arrestor minimum of 1 kv. driver current not less than 700ma, thd< 10%.lumens package not less 100 lm/w for led source. test certificate from nabl 9national accredited board for testing & calibration laboratory) for lm79 report.in house testing facility to be available for the same.lamp life not less than 50,000 hours etc ; complete as per standard specification .3 rm supply and delivery of 3 core 1.50 sqmm flexible cable with isi mark. supply and delivery of 40 mm dia b class (l shape) gi bracket , supply and delivery of 7 x 3 x 4 mm rcc postclamp size 50x3mm thickness with 6 nos of 5/8 full thread 2 ms bolt nuts. labour charges for fixing of new 90 w led lamp fittings complete set and including all necessary items. as directed by departmental officers etc complete. , supply and fixing of 8 metre length gi steel tubular pole for street light single bracket pole with base plate (250x250x6mm) of 114.30mmod x 5.4 mm thick x 4500mm length,88.90 mm od x 4.85mm thick x1750 mm length, 76.1mm od x3.25mm thick x 1750mmlengthcomplete set and including all necessary items. as directed by departmental officers etc complete , supply and fixing of4.00sqmm 3core copper cableincluding all necessary items. as directed by departmental officers etc complete(twad sor 2021 22sl. no. 12.1, page 116.) , supply and fixing of ms box synthetic moulded compound box for street lightand including all necessary items. as directed by departmental officers etc complete , supply and fixing of 24 hours analag timer switch with shortest switching time 30minutesincluding all necessary items. as directed by departmental officers etc complete.(pwd sor page no.115 ) , labour charges for erection of8 metre gi single bracket pole including earth work excavation for pit ,foundation conctrete ,steel fabrication ,rcc 1:1.5:3 mix andall labour charges for laying and fixing in position etc,..complete.(as per working sheet)....

Due Date : November 29, 2023

Tender Value : ₹ 12.45 Lakhs

View Tender
26
Municipal Adminitration And Water Supply Department - Tamil Nadu

40814854 tender for green space development at saminathan nagar park in thuraiyur municipality.; 1 earth work excavation for foundation in hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders ss.20b and sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blastinginclusive of shoring shuttering and baling out water and cleaning and levelling the site etc., complete narrow foundations upto 2.00m depth 2 earth work excavation for foundation in hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders ss.20b and sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blastinginclusive of shoring shuttering and baling out water and cleaning and levelling the site etc., complete open earth work excavation 3 supplying and filling in foundation andbasement with crushed stone dust in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification. 4 plain cement concrete 1:4:8 ( one cement, four fine aggregates and eight coarse aggregates ) using 40mm size iss hbg metal including cost and conveyance of all materials to site and labour charges and all incidential charges such as water providing etc., complete as per standard specification 5 supplying and erecting steel centering including necessary supports for plane surfaces for reinforced cement concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 bg stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation 6 plinth beam 7 centering for soffits of rcc slabs of plane surface like lintels, beams , etc., including strutting 3m high using mild steel sheets of size 90cm x60cm x and b.g 10 stiffened with m.s angles of size 25mm x 25mm x 3mm laid over silver oak ( c.w ) joists of size 10cm x 6.5cm ( spaced at about 90cm c / c ) and supported dy casurina props of 10cm to 13cm dia ( spaced of 75cm c / c ) complying with standard specification and directed for plane surfaces such asrectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc. 8 column 9 lintel, slab 10 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg / cum and maximum water cement ratio of 0.55 including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about ( 5.0cum ) , 7730kg of 20mm machine crushed stone jelly and with about ( 3.3 cum ) , 5156kg of 10 12mm machine crushed stone jelly and with about ( 4.79cum ) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental upto basement 11 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg / cum and maximum water cement ratio of 0.55 including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about ( 5.0cum ) , 7730kg of 20mm machine crushed stone jelly and with about ( 3.3 cum ) , 5156kg of 10 12mm machine crushed stone jelly and with about ( 4.79cum ) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is standards. ( no separate payment will be made by the department for the excess usage of materials ) ground floor 12 supply and fabrication of steel required for all rcc items of works involved in the schedule, cost of steel at site fabrication, labour charges for cleaning the rods straightening, cutting, bending, tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as as per design given and specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc complete as per standard specification 13 plain cement concrete 1:2:4 ( one cement, two fine aggregates and four coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and labour charges and all incidential charges such as water providing etc., complete as per standard specification 14 brick work in cm 1:5 ( one cement & five crushed stone sand ( m sand ) ) using ii class ground moulded bricks of size 9 x 43 / 8x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification 100cft ground floor 15 plastering with cement mortar 1:3 ( one part of cement and three part of plastering sand ( p sand ) ) , 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications 16 plastering with cement mortar ( 1:5 ) 12 mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc, complete as per standard specifications. 17 providing and laying, spreading and compacting graded stone aggregate to wet mix macadam ( wmm ) specification including premixing the material with water at omc in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of morth specifications. 18 supplying and laying rubberised interlocking paver blockm40 grade providing and laying of63mmthick high strength type conforming is 15658 2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 19 paving the floor with design antiskirt ceramic tiles ( colour and shade as directed ) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 ( one part of cement and three part of plastering sand ( p sand ) ) , 20mm thick laid in situ and pointed with same coloured cement 20 paving the floor with double charged vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 ( one part of cement and three part of plastering sand ( p sand ) ) , 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg / m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer.the colour & quality of tiles should be got approved by municipal engineer before use on work 21 dadooing walls withglazed tiles of sizes 305mm x 200mm x 6mm size of approved make and quality and colour set in cement mortar 1:2 ( one part of cement and two part of plastering sand ( p sand ) ) over 10 mm base layer plastering and pointing with white cement neatly as directed 22 providing upvc ( un plasticized polyvinyl chloride ) door:providing and fixing casement dorrs fabicated from un plasticzed polyvinyl chloride ( upvc ) sections. profiles:the profiles should be three chamber system which provides high insulation properties which outer frame 60mmx55mm with an outer wall thickness of 2.4mm.the window unit should be desined with all corner jointsmitred and fusion welded. windows should be steel reinforced with 25x24x25mm steel reinfocrement with a thickness of 1mm to have dimensional stability.the sash shold be of 60x102mm. the mulion should be of 60x74mm the profile 23 supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 25gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work 24 supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with gi / 1mm 125gsm and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiations pin headed glass 4mm thick should be provided in the louvers. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the ventilator should be got approved from the executive engineer before use on work 25 weathering course with concrete broken brick ( s.i.no.278 ) & ( p & d ) data 54.jelly 20mm gauge in pure slaked lime ( no sand to be added ) over roof slab, the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers.etc., complete as per standard specification. 26 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification. 27 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 28 supply and fixing of m.s grills with doors and windows with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specification. 29 painting two coats of newly plastered wall surface with approved cement paint over cement plastered wall surface, ceiling andincluding preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required and cost of painting materials, brushes, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer 30 painting the new iron work with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer. 31 painting two coats for interior surface with approved interior plastic emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. 32 supplying and fixing in position white / colour glazed model floor mounted european water closet of best quality and approved make with 100mm “p” or “s” trap connecting with ci pipe of 100mm dia / pvc pipe of 110mm dia, double flapped rigid pvc black seat and seat cover with cp brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity pvc / 12.5 liters capacity porcelain low level flushing tank with a pair of ci brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white pvc flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm gm wheel valve, 15mm brass nipple ( 2 nos. ) , 15mm nylon connection, tw plugs, screws and also giving necessary connection to the pvc pipe and painting the ci brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re doing the dismantled masonry to original condition, etc., complete complying with standard specifications. ( the ewc and flushing tank with all accessories should be got approved by the executive engineer before use on works ) floor fitting 33 supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 x 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape, 32 mm diametre c.p. waste union, 32 mm diametre p.v.c. waste pipe with rubber plug and chain, 15mm diametre g.m.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of c.i. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications 34 construction of inspection chamber of sizw 60x60x60 with necessary earth work excavation 40mm size brick jolly concretein cm 1:4:10and 10 broken brick jelly work cm 1:6 for 23 cm thick wall benching chennelling and plastering interoir etc, 35 construction of inspection chamber of sizw 60x60x90 with necessary earth work excavation 40mm size brick jolly concretein cm 1:4:10and 10 broken brick jelly work cm 1:4 for 23 cm thick wall benching chennelling and plastering interoir etc, rcc loose slab coverin in cc 1:2:4 36 supply & fixing of 48 sweep size celling fan of 5 star rated with double ball bearing.down rod, canopy complete set ( with out speed regulator ) ( on existing clamp with 300mm down pipe ) sd 37 wiring with2 x 1.5sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor cable of 1100v grade in suitable heavy gaugemsconduitpipeon wall andceiling withms accessories with switch boxwith5a ft switch inflush wit hwall andcovered withhylum sheet of 3mmthick withpainting of suitable colour withcontinuou searth wireconnection of 14 swg tc wire for light point / fan point ( for electronic regu sd 38 supply and fixing of surface mount patty type 1x36 watt t.l fitting complete with electronic ballast with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminal to the fitting. sd 39 wiring with 2 x 1.5 sqmm ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3mm thick hylum sheet cover with tw switch box and 5a f.t. switch with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point ( for electronic regulator ) . sd 23 40 supply and fixing of wt bulk head fitting with guard suitable for 11w cfl lamp with cfcsd 83 41 supply and fixing of300mm ( 12 ) sweep ac exhaust fan complete with necessary wall opening sd 42 supply and fixing isi marked 2x26 sq.mm cable 43 supply and fixing hdpe plan pipe of size 50mm with silicon coating 44 laying of cable alone road / street through 50mm od hdpe pipe ( trench size 45cm width x 75cm depth ) 45 supply and fixing 32a dp mcb isolator 46 supply and fixing single pole 6a to 32, 10ka 47 earthing as per p.w.d standard with an earth electrode of 2 mtr. class b gi pipe of dia not less than 32mm complete with necessary masonry work sd 234 48 supply and jointing 25mm dia pipe 49 supply and jointing 20mm dia pipe 50 supply and fixing pvc screw down tap 51 supply and fixing 25mm dia wheel valve 52 supply and fixing 20mm dia wheel valve 53 supplying 50mm size six level type brass lock of superior make with relevent isi keys in duplication 54 conducting geophysical survey, quality and quantity test and transportation charges etc, ( this includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist ) 55 drilling 6 vertical bore in hard rock area to any required depth as directed by the board officers including labour charges for inserting casing pipes assembly in the directed hole including welding the joints if necessary grounding the casing pipes etc., and including transporting from one place to another etc., complete twad sor p.g.no 279, 2022 2023 56 supply and delivery ofpvc casing pipe of the 200mm dia pipes as per is / 12818 / 92 and as amended from time to time to suit the borewell upto 150m depth ( cm ) with isi marking including, loading, unloading , freight, stacking and transit insurance charg 57 labour charges for inserting pvc casing pipes assembly ( with slots or without slots ) in the drilled hole including jointing the pipes with pvc couplers with cement paste etc., complete. 58 earth work excavation for foundationin ordinary soil light black cotton sandy loam and dry silt including shoring, strutting, baling ( or ) pumping out wter wherever necessary and refilling the sides of foundation with excavated in layers of 15cm thick and depositing the surplusat places as directed by the dept. officerswith initial lead and lift etc., complete as per standard specifications. 59 refilling with excavated earth in layers of 15cm thick including watering and ramming to consolidation etc complete 60 supply of upvc pipe 32 mm 61 supply of 50mm dia gi pipe 62 supply of 50mm dia gi elbow 63 supply of 50mm dia gi flange 64 supply of 63mm pvc bend 65 supply of 63 mm pvc elbow 66 supply of63 mm pvc pipe ( 6ksc ) 67 supply of 63 mm pvc tee 68 supply and fixing pvc pipe 110mm rain water doen wall sd 69 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1 x 1 / 8 copper flat ) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit..sd 127 70 supply and fixing of 50mm dia gm gate valve with isi make, the cost shall including materials, fixing and labour charges etc, complete as per standard specification.sor 71 supply of 4 sq.mm pvc insulated and sheathed 3 core flat type copper cable conforming to is 694 / 1990 sor 72 supply of3 hp three phase100lpm x 75m submersible pumpset suitable for 150mm dia borewell without panel board as per is 8034 / 2002 73 supply of 3 hp three phase panel board d.o.l. with two level guard . panel board should be provided as per specification ( twad 22 23. p 111 ) 74 supply of triple pole switches 32 amps tpn metal clad switch with rewirable fuse units ( twad sor p.no 178 ) 75 supply of32 amps porcelain fuse unit ( 500 v ) ( twad sor p.no 179 ) 76 supply and delivery of ms kiosk of size 0.75m x 0.45m x 0.75m made up of ms angle of size 50mm x 50mmx 4mm alround covered with 16 gauge ms sheet and kiosk door made up of ms plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc., twad 22 23. p 85 77 supply and fixing 200mm dia pvc end cap as bore cover on topfor securing 78 supply and run of 4 of 4 sqmm ( 56 / 0.3 ) pvc insulated sc unsheathed cu. conductor of 1100v on 7 / 20 gi bearer wire for service connection mains ( sd 67 ) 79 supply and fixing nylon rope ( pwd 22 23. p 105 ) 80 supply and delivery of 25 mm dia gi pipes 81 labour charges for the erection of submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps, erection clamps, pressure gaugesetc., complete andtesting the pumpset and trail run for 10 days. sor 82 earthing as per p.w.d standard with an earth electrode of 2 mtr. class b gi pipe of dia not less than 32mm complete with necessary masonry work sd 234 83 supply & fixing of ac / dc 76mm buzzer suitable for 230 volts 50 c / s single phase ac supply on suitable tw board with push switch. sd 105 84 supply and fixing of 6 metre length single bracket pole with base plate ( 250 x 250 x 6mm ) 76.10mm od x 3.65mm thick x 6000mm length in control box with foundation hardwares.etc completed as per standard specification.as per pwd sor 2022 2023 p.no 148 85 supply and fixing of 25w led street light fittingas per pwd sor p.no 115 86 supply and fixing of 4 x 16 sqmm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75m for covering the cable complete with 2 dia pvc pipe etc, complete sd 87 supply and fixng of tneb meter board suitable for 3 phase 63a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 / 2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos. 63a fuse units ( 500v ) , 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 16 sq.mm pvc insulated copper wire with earth connection complete ele sd 129 88 supply and fixing of 200a tpn sheet steel double break switch with hrc fuses and neutral on suitable angle iron frame work with ms cable entry boxes and with earth connection only ele sd 170 89 supplying and fixing of double swing of height 2.40m height with 40mm diam.s. pipes support as legs and top bar is 50mm dia.the seat is 9mm thick reinforced rubber with antiskid chequred top with heavy ball bearing and the suspension is 7mm dia electro galvanized chain and the cost shall inclusive of all materials, labours and fixingetc, complete as directed by the departmental officers. ( q ) 90 supplying and fixing of two seater seesaw for below 12 years old childrens to a height of 0.50m with 50mm dia leaver and 40mm top bar with m.s. pipes. the seater is of moulded plastic with heavy duty bush bearing. the cost shall inclusive of all materials, labours and fixingetc, complete as directed by the departmental officers. ( q ) 91 supplying and fixing of four seater seesaw for below 12 years old childrens to a height of 0.50m with 50mm dia leaver and 40mm top bar with m.s. pipes. the seater is of moulded plastic with heavy duty bush bearing. the cost shall inclusive of all materials, labours and fixingetc, complete as directed by the departmental officers. ( q ) 92 supplying and fixing of slide for below 12 years old childrens to a length of 3.00m with 80mm dia leaver and 40mm top bar with m.s. pipes. the seater is of moulded plastic. the ladder frame is made up of 25mm m.s.pipe, hanrail 20mm dia m.s. pipe and the centre support is 80mm dia m.s. pipethe cost shall inclusive of all materials, labours and fixingetc, complete as directed by the departmental officers. ( q ) 93 supply and fixing of duck rider: [ component ] leg :galvanished ‘c’ class pipe galvanished ‘b’ class pipe spring: mild steel springduck:frp with isotolic gel coat with uv pigment. paintingwith pu coating [ required area ] product area : 3ft *3ftplay area : 5ft*5ft [ measurement ] width:3ft ( q ) 94 supply and fixing ofmerry go round – 6 seater ( frp ) height :3” gi pipe, 2.5mm thick, b class seat size:15”x 14”, paint: pu coating ( q ) 95 providing and planting of ornamental plants like golden, bamboo, focus verities, albania verities, buda bamboo trees, etc with inclosing cost of plants, red earth manure and including all labours chargesfor pit excavation fertilizing ( q ) 96 providing and planting of palm clusters like as harika palm, phoneix palm, sun palm, table palm etc with including cost of plants, red earth manure and including all labour charges for pit excavation fertilizing planting etc complete. ( q ) 97 providing and planting of border plants using duranda clirodendrom, follage, exora, pmc neerium etc with inclosing cost of plants, red earth manure and including all labour charges earth work excavation fertilizing planting etc complete ( q ) 98 providing three seater arrangements with ready made granite benches 20mm thick slab with 1500mm wide , 600mm height. the cost shall include all labour and materials and as directed by the departmental officers. 99 supply and delivery of 1000 lit capacity and fixing of hdpe tank as per is 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the gi pipes and specials for pipe connection works including cutting, threading and fixing charges etc., complete as per standard specification. sor 100 supply and fixing of 20lit capacity tilting type stainless steel garbage bins in park area as per the site condition and as directed by the departmental officers. 101 supply and erection armoured cat 6 cable ( pwd sor p.no 153 ) 102 supply and erectionpoe switch for camera 8 port ( pwd sor p.no 154 ) 103 supply and erection hard disk for nvr 4tb ( pwd sor p.no 155 ) 104 supply and erection net work video record for cctv 8 channel sata 1 no hard disk ( pwd sor p.no 154 ) 105 supply and erection of cctv camera 106 supply and erection of rack with accessories 6u rack ( pwd sor p.no 155 ) 107 supply and erection i / o soket rj 45 ( pwd sor p.no 155 ) 108 supply and erectioni / o soket rj 11 ( pwd sor p.no 155 ) 109 supply and erection of 29 led tv 110 provision for goods and service tax 18%...

Due Date : December 08, 2023

Tender Value : ₹ 53 Lakhs

View Tender
30
Military Engineer Services - Tamil Nadu

40783386 tender for repairs to pcc roads, hardstanding and road furniture at technical area cvrde, avadi.; 1 repair topotholesanydepthn.exc1sqm eachincludingsweepingfreefromdustandmudorwaterscoringsunkensurfacesinroadpathmakinggoodbyapplyingtackcoatbituminousprimer@ 5 kg per10 sqmputtingin premixasspecifiedforbituminouscarpet ( 2cmthick ) wellrammedand sealedwithpremixedsandsealcoat ( 6.80kg binder with 0.06 cumofsand ) againwellrammed. complete all as specified and as directed 2 preparing surfaces of black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed 3 m&lonblacktopsurfacesandapplyingevenly apriming / tackcoatwithbituminousprimer @ 5kg per x sqminpavingbitumenasspecifiedand directed .complete all as specified and as directed 4 m&lfor bitmuminous premix semi dense asphaltic concrete, 30mm consolidated thickness with 5.5% of binder content by weight of total mix and compacted to reqd camber and gardient with mechanical paver complete all as specified andasdirected . 5 m&l for providing hot applied thermoplastic compound 2.5mm thick and providing selecting glass beads @ 250gm per sqm as per irc 135, finished and existing old surface of painting lines dashes, arrows, letters etc.on roads / concrete exe10cm wideto be leveled uniform and free from streaks and holes including cleaning of surface to remove a loose dirt etc; complete all as specified. and as directed. 6 demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and asdirected by engineer in charge. 7 m&lfor sand filling under floors or in foundation including watering and consolidation complete all as specified and asdirected by engineer in charge. 8 m&l for layingpolythene film, black, 50 micron laid in floors complete all as specified and as directed by engineer in charge. 9 m&l for pavement quality cement concrete ( pqc ) work in pavement / hard standing of flexural strength 40 kg / per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less including necessary steel formwork complete all as specified and asdirected by engineer in charge. 10 m &l for forming 12mm thick machine cut expansion filled with premormed bituminious filler and top 30mm primed and sealed with sealing compound grade b for concrete slab 150mm thick complete all as specified and as directed by engineer in charge. 11 m&l for forming dummy joint 65mm deep x 10mm wide of machine cut filled with sealing compound grade b complete all as specified and as directed by engineer in charge. 12 finishing surfaces of concrete road by machine brooming on concrete surfaces while concrete is in green position all as specified andas directed by engineer in charge. 13 painting lines dashes, arrows, letters etc.on concrete roads surfaces with ( two or more coats ) of concrete floor paint to give uniform finish with road marking paint of superior make as approved by the engineer in charge, i / c cleaning the surface of oil dirt, scales, oil, grease and other foreign material etc. and lining out complete all as specified and asdirected. 14 m&l for cement concrete type b 1, 1:2:4 ( using 20 mm graded stone aggregate ) asinsub base complete all as specified andas directed. 15 m&l for machine pressed coloured precast with grey cement and pigment conctete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness, m 35 grade over a layer of 25mm thick sand cushion complete allas specifed andasdirected. 16 m&l for hydraulic pressed chequered cement concrete colour tiles 300mmx300mmx 25mm, set, jointedand pointed in thick neat cement slurry in floors and pointed with white cements and pigments iincluding screed bed or bedding layer of cement mortar 15mm thick for laying floor finishes with cm 1:6complete all as specified and as directed 17 demolition of brickwork or stone / boulder masonry or cement block masonary, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified andas directed by engineer in charge. 18 m&lforbrick work with sub class b brickes straight or curved on plan exc 6m mean radius in plan built in cm 1:6 complete all as specified andas directed 19 m&l for rendering 15mm thick in fair faces of brick work or concrete surfaces in cm 1:4 finished even and smooth with out using extra cementcomplete all as specified andasdirected. 20 m&lforpre cast cement concrete type c1 1:3:6 block masonary with solid blocks exe 10cm in width and setting in cement mortar 1:6 complete incld necessry excavationembedding blockin the ground to depths directed , required andtempering around and removing surplus spoil to a distance not exc 50 mtr and deposting where directed all as specified and as directed by engineer in charge. 21 s&f in repairs rubber speed bump of size 50 mm ( height ) x 375 mm ( width ) x 500 mm ( length ) , abs block black and yellow & reflectors on both sides including necessary fixing arrangements with epoxy / thermoplastic adhesive and anchor bolts all as per manufacturers instructions and complying to guidelines issued by min of road transport etc. complete and as per direction of engineer in charge.make:cateye / darkeye / suneyez / 3m 22 manufacturing, supplying and fixing cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm of retro reflective sign boards made up of 3 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type iv of astm d 4956 01 in blue and silver white or other colour combination including subject matter, message ( bi lingual ) , symbols and borders etc. as per irc ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class 2 of astm d 4956 01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c / c to back support frame of m.s. angle iron of size 35x35x5 mm along with theft resistant measures, mounted and fixed with 2 nos. m.s. angles of size 35x35x5 mm to a vertical post made up to m.s.tee section ismt 65x65x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including embedding in pcc 1:2:4 ( 300x300x750mm ) type b1including removal of excavated soil to a distance not exc 50 m and making holes in pipes, angles flats, providing & fixing m.s. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer ( vertical ms tee support to be painted in black and white colours ) .backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of engineer in charge.note: demolition of cement concrete in concrete road surface for making holes to be paid separately 23 m & l for preparation of new / old concrete kerb stone surfaces / plastered surface and applying two or more coats of first quality retro reflective enamel paint onkerb stone, etc to give uniform finish of any colours over a coat of primer and pattern complete all as specified andas directed by engr in chargemake : berger guidline / dulux trade line / indigo 24 s&f in repairs road convex safety mirror outdoor type made of one piece of polycarbonate traffic mirror unbreakable round wide angle of size 80 cms dia, outdoor type, including mountedsteel frame along with ms pole supporting of varying height including all fixing arrangementswith adjustable brackets and nuts bolts for installation, suitable for driveways, garages, warehouses and buildings blind spots and necessary foundations including excavation & removal of soil ( 300mmx 300mm x 450 mm with m15 using 20mm graded stone aggregate ) complete all as specified and as directed.make:cateye / darkeye / suneyez / 3m 25 supply only calcium hypo chlorite granules packing size ne less than 45kg , 65 95 concentration complete all as specifed and directed....

Due Date : December 14, 2023

Tender Value : ₹ 15 Lakhs

View Tender
31
Military Engineer Services - Tamil Nadu

40773911 tender for special repairs to certain building at kattabomman under ge tirunelveli ( tender id:2023_mes_629434 _1 ) ; 1 dismantling corrugated or semi corrugated asbestos cement sheets in roof covering, all as specified and directed. 2 supply and fixing pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. 3 supply and fixing prepainted galvalume aluminium zinc coating gi based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof, fixed with self tapping screws complete all as specified and directed. 4 material and labour for 610mm dia aluminium 0.50mm thick turbo ventilators with 47 vanes including frp / aluminium base plate fixing with galvalume roof sheet including necessary fixing arrangements complete all as specified and directed. 5 material and labour for 25mm thick plain cement concrete type b 1, 1:2:4 ( using 20mm graded aggregate ) as in floorcomplete all as specified and directed. 6 material and labour for providing colour non skid joint free ceramictiles 7 to 8mm thick square / rectangular, area of each tile exceeding 0.18 sqm but to exc 0.38 sqm in floor of approved quality and patternset , and jointed in neat cement slurryand pointed in coloured cement to match in floors over 15mm thick screed bed in cm 1:6 complete all as specified and directed. 7 material and labour for non skid ceramic colouredtiles7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc., setand jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including screed bed or bedding layer of mortar 15 mm thick in cm 1:6 complete all as specified and directed. 8 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 9 material and labour for colour non skid joint free ceramictiles 7 to 8mm thick square / rectangular polished , on vertical surfaces such as skirting dado riser to steps , setand jointed in neat cement slurryand pointed in coloured cement to match in floors over 10mm thick backing coat in cm 1:4. complete all as specified and directed. 10 material and labour for 50mm thick plain cement concrete type b 1, 1:2:4 ( using 20mm graded aggregate ) as in floorcomplete all as specified and directed. 11 supply and fixglass dividing strips 38 x 3mm thick complete all as specified and directed. 12 demolition of reinforced cement concrete of roofs, floors ( other than ground floors ) , beams, staircases, landings, chajjas and similar suspended work complete all as specified and as directed . 13 material and labour for rcc 1:2:4 ( nominal mix ) type b1 ( using 20mm graded stone aggregate ) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies deck slab and shelves and the like complete all as specified and directed. 14 material and labour for formwork to soffits of suspended slabs such as landings, shelves and similar work : not exceeding 200mm thick ( horizontal or sloping ) for rough finished surfaces of concrete complete all as specified and directed. 15 material and labour for tmt bars 10mm dia and over cut to length bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and bindingwith and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 16 material and labour pcc 1:3:6 typec120 mmgraded aggregate 75 mm thick in plinth protection finished even and fair without using extra cement complete all as specified and directed. 17 material and labour pcc 1:3:6 typec120 mmgraded aggregate in surface channel and drain complete all as specified and directed. 18 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms moulds , mitred stopped ends etc complete all as specified and directed. 19 taking down cement plaster on brick or stone wallincluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 20 material and labour for rendering 10mm thick on brick or concrete surfaces in cm 1:6 on fair faces of brick work or concrete surfaces of wall finished even and smooth ( without using extra cement ) complete all as specified and as directed. 21 material and labour rendering 15mm thick in cm 1:4 on o fair faces of brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. 22 demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins arches, pillars etcall as specified and as directed. 23 material and labour for brick work with fly ash bricks straight or curved on plan exec 6 mtr mean radius with cement mortar 1: 6. complete all as specified and directed. 24 material and labour preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 2mm thick wall care putty on wall complete all as specified and directed. 25 material and labour preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces complete all as specified and directed. 26 material and labourfor complete removal of existing treatment andapplying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces complete all as specified and directed. 27 material and labourfor complete removal of existing treatment and applying two coats of oil bound distemper over a coat of alkali resistant primer over 2mm thick wall care putty on wall complete all as specified and directed. 28 material and labour for preparation of old plasteredsurfaces & applying two coat of white wash on ceilings complete all as specified and as directed.. 29 material and labour for preparation of old steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and as directed. 30 taking down shutters exceeding 1.0 sqm and not exceeding 2 sqm and removing from site complete all as specified and directed.. 31 material and labour flush door shutters, 35mm thick, solid core construction, withboth faces is covered with decorative face veneer with lipping / frame to match and glazed vision panels of size 20 cm x 20 cm, including lipping complete all as specified and as directed. ( note glass shall be measured and paid separately ) 32 material and labour for french polishing on surfaces of any description width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed. 33 material and labour for hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 34 supply and fix 4.0mm thick plain sheet glass of ordinary quality and glazing with oil putty n exc 0.5 sqm fixed to steel framing complete all as specified and as directed. 35 supply and fixing butt hinges heavy weight cold rolled mild steel and fixed in 125mm long complete all as specified and directed. 36 supply and fixing in repair butt hinges heavy weight cold rolled mild steel and fixed in 125mm long complete all as specified and directed. 37 supplying and fixing aluminium anodised barrel tower bolts of extruded section 150 mm and fixed complete all as specified and directed. 38 supplying and fixing extruded aluminiumhandles fabricatedtype anodised 150mm long complete all as specified and directed. 39 material and labour for aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections ( 250 mm length ) complete all as specified and directed. 40 supply and fixing in repairs door closer aluminium extruded section body hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. 41 dismantling wrought iron or mild steel work of any description complete all as specified and directed. 42 material and labour for welded steel wire fabric not exc 4 kgs / sqm supplied and fixed complete to wood or steel members complete all as specified and directed. 43 material and labour for framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 complete all as specified and directed. 44 dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. 45 supply and fixing steel rolling shutters 1.25mm thick , with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, completegear operated type with bevel gear box and crank handle complete all as specified and as directed. 46 supply onlyball bearing wheelfor the rolling shutter complete all as directed by engineer in charge. 47 supply onlysafety lever locks mild steel with 4 levers for the rolling shutter complete all as directed by engineer in charge. 48 material and labour for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 49 dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover filletscomplete all as specified and as directed. 50 material and labour gl frame work for seamless ceiling comprising of gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with gl cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having knurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. hangers 6 mm dia. g.i. ( upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 51 material and labour for 8mm thick seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish ( frame work for ceiling shall be measured and paid separately ) finished with 2mm thick putty over calcium silicate board and two coats oil bound distemper over a coat of primer complete all as specified and directed. 52 schedule of credit amount brought back from ser page no. 29 rs. 54, 404.00 will be deducted from the above quoted amount to derive the contract sum.signature of contractor...

Due Date : December 14, 2023

Tender Value : ₹ 32 Lakhs

View Tender
32
Municipal Adminitration And Water Supply Department - Tamil Nadu

40770948 construction of two class rooms & laboratory ( fisrt floor ) in girls higher secondary school in ward no.16 at mettupalayam municipality; 1 earth work excavationin all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. ( for foundation ) 2 cement concrete in 1:4:8 [ one cement and five sand andten aggregate ] using40 mm size iss grade machine crushed chips including the cost of mixinglaying curing etc., complete complying with standard specification. 3 reinforced cement concrete 1:1 1 / 2:3 ( one cement one and half sand three aggregates ) using 20mm iss hbg metal including cost of all materials and labour charges for mixing, laying, finishing and curing etc complete but excluding cost of steel & centering charges etc., completeas per ss 4 for basement 5 for ground floor 6 supplying, fabricating and placing in position of steel reinforcement using mild steel or ribbed tor steel rods, for all rcc worksas per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete as per ss. 7 supplying and erecting steel centering for sides andsoffits including supports and strutting upto3.29 m height for planesurfaces such as rcc slabs, rectangular beams, tee or ell beams, lintels, bed blocks, staircase waist and landing slabs, landing beams, canopyetc., with all cross brasingsusing mild steelsheets of size 90cmx60cm and 10 gauge stiffenedwithwelded ms anglesof size 25mmx25mmx3mm for boardinglaid over silver oak ( cw ) joists of size 10cmx6.5 cm spaced at about90cm c / c and supported by causrina props of 10cm to 13cm dia spaced at 75cm c / cetc., complete complying with standard specification and as directed . 8 for columns 9 for plinth beams 10 for slab & beam 11 brick work in cm 1:5 mix using best country bricks of size 23cm x 11.50cm x 5cm having 350kg / cm2 compressive strength and 15% or less water absorbentin the period of 24hours immersement and confirming toisi specifications.and using the screenedsandand all the materials should be approved by the competent technical authorities etc complete complying with standard specification 12 for basement 13 frp door sutter with frp door frames made out of frp sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using ms angle / flats, cost of holdfasts and solid core frp shutter panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by engineers 14 supply and fixing of stainless steel ( salem stainless steel ) door frame ( box section using stainless steel plate of 1.6mm thick ) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc. 15 supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 25gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work 16 plastering in cement mortar 1:5 mix 12mm thick using clean screened sand and including cost of curing for fifteen days from the completion of thework and surface should free from undulationsand including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortaretc.complete complying with standard specification 17 plastering in cement mortar 1:3 mix 10mm thick using clean screened sand and including cost of curing for fifteen days from the completion of thework and surface should free from undulationsand including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortaretc.complete complying with standard specification 18 paving the floor with best approved quality fine polished shahabad stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 ( one cement and three sand ) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification 19 supplying and laying in flooringwith fully polished sinthetic grey colour granite stone of 20mm thick ( average ) of 4 x 2 in size laid over base layer of cementmortar 1:3 ( one cement and three plastering sand ) 20 mm thick and applying cement slurry &pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers 20 painting two coats for interior surface with approved plastic emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. 21 wiring with 2x1.5sqmm ( 22 / 0.3 ) pvc insulated unsheathed sc. cu.conductor of 1100v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with 5a f.t. switch inflush with wall, covered with hylum sheet of 3mm thick with painting of suitable colour for open pvc light / fan point ( for electronic regulator ) ( 5 points per coil ) sd 22 22 supply and fixing of 1400 mm ( 56 ) sweep ac ceiling fan complete with stepped electronic regulator with 300 mm down rod on the existing clamp etc. complete as per standard specification sd 111 23 supply and fixing of single box type 440 w flu fitting complete with copper choke and condensor with tw round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting. sd 88 24 wiring with 2x4 sqmm ( 56 / 0.3 ) pvc insulated sc unsheathed cu.conductor cable of 1100v grade in suitable pipe on wall and ceiling with pvc accessories with 150 mm x 100 mm x 63mm tw switch box for 15 a 3 pinnon inter locking cs plug with painting of suitable colour, with continuous earth wire connection of 14 swg tc wire for open pvc power plug point.sd 13 25 supplay and ran of 4 x 6 sqmm ( 84 / 0.3 ) 7 / 20 sqmm pvc unshuitable coper cable in shuitable pvc rigid pipe sd 68 26 supply and fixing of 65 mm ( 21 / 2 ) gi pipe ( class b ) of 6 mt. length with 300mm x 300mm x 6mm ms base plate, duly welded at the bottom with concreting with construction of masonary pedestal with suitable ms box to house 5a control switch 16 a fuse unit ( 500v ) etc. with suitable angle iron frame work, with door and with lock and key arrangements and with supply and fixing of 440 w twin street light flu.fitting with copper chokes and condenser with flu.tubes with 1 metre of 32mm dia gi pipe ( class b ) complete, with necessary clamps, on the above post with pvc unsheathed leads with painting of suitable colour.sd101 27 weathering course with concrete broken brick ( s.i.no.278 ) & ( p & d ) data 54.jelly 20mm gauge in pure slaked lime ( no sand to be added ) over roof slab, the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete. 10 cum 28 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete 29 supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 x 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape, 32 mm diametre c.p. waste union, 32 mm diametre p.v.c. waste pipe with rubber plug and chain, 15mm diametre g.m.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of c.i. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications...

Due Date : December 12, 2023

Tender Value : ₹ 57 Lakhs

View Tender
33
Rural Development And Panchayats Department - Tamil Nadu

40740461 tender for providing via ravandi block.; 1 construction of building for hsc building @ asoor panchayat in vikkiravandi block. 2 clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 3 earthwork excavation for foundation ( for narrow excavation ) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification. 4 supplying and filling in foundations and basement with fillingm sand in layers not exceeding 15 cm. thick, well watered , rammed and consolidated etc. complete complying with standard specifications. 5 plain cement concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. 6 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 7 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete. 8 supplying and erecting centering and shuttering for soffits including necessary supports and strutting up to 3 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) . 9 upto basement 10 ground floor 11 providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of m25 grade for reinforced cement ratio with plasticizer using 20mm and down concrete structural elements under controlled water graded machine broken granite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart mental officers comple. 1m3 12 foundation & basement 13 ground floor 14 steel fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 15 brick work in following cement mortar 1:5 using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4 for foundation and basement including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the engineer in charge. 16 foundation basement 17 ground floor 18 brick partition walls of 11.50cm thickness using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) . 19 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor slabs, beams, and sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the enineer in charge. this rate includes the cost of providing cement mortar beadings for sun shades, steps, landing slabs, elevation etc. complete complying with standard specifications. 20 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 21 paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm ( un polished ) in all floors laid in of cement mortor 1:3 ( one cement three m.sand ) , 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification. 22 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.464 / sq.m 23 dadoodling the walls with colored glazed tiles approved size, quality and color set in cm 1:2 10 mm thick. and pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 kg / sqm etc. complete. basic cost rs.318 / sq.m 24 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) . 25 providing, fabricating and fixing m.s. grillswindows, and ventilator, gates, ladders, rail pipes, nosing angles, with m.s.lugs in staircase steps etc., made out of m.s rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the engineer. 26 manufacturing, supplying and fixing of stainless steel handrails for staircase using 50mm dia 304l grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete.the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, ect.complete. 27 solid pvc door shutters toilet door using 19 gauge 19mm ms square tubes for styles and outer frames.15mm ms square tubes for top, lock and bottom rails.the steel tubes shall be covered with 5mm thick solid pvc sheets.shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.the over all size of styles shall be 50mm x 30mm.the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.the over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. 28 upvc windowsupplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g / 1mm 125gsmand 100% corrosion free, the profiles are multi chambered sectionwith wall thick of 2mm. the epdm rubber ( black color ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power points locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed or plainglass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and shouldhave key lockable action, security protective hinges, strong lockingsystems and as per sizefor arrestingnoise and energy loss. 29 upvc ventilator: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with gi / 1mm 125gsmand 100% corrosion free , the profile are multi chambered sections withwall thick of 2mm. the epdm rubber ( black color ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. the ventilator should be got approved from the executive engineer before use on work. 30 painting two coats of synthetic enamel paint of approved colour and make over one coat of anti corrosive zinchromite primerover new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications. 31 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 32 painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. 33 weathering course concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( no sand to be used ( over the rcc roof slab in the proportion of brick jelly to lime being 32 : 121 / 2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed 34 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. 35 supplying and fixing in position best approved quality ( oriya type ) white indian type water closet530 mm x 440 mm white glazed earthern ware of approved quality and brand with p or s trap conforming to bis with sand cushion and forming flooring alround the closet using 40 mm broken brick jelly in lime concrete 1:2:5 ( one lime, two sand and five brick jelly ) 100 mm thick and finishing the top to the required slope and including giving necessary connection to ci soil pipes ( including the cost of 100mm dia ci pipe for a length of 600mm ) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officer. 36 supplying and fixing of indus floor mounted white colour european water closet parryware or equivalent, with seat cover and dual flush ( 3 & 6 lit ) cistern having p trap withseat cover, supplyingnon corrosive hinges, cp bolts, nuts, washers, providing and fixing dash anchor fastners with bolts / l brackets with anticorrosive paint cutting grooves in masonry or concrete surfaces, groutingwith cement concrete 1:2:4 mix, using 20mm size stone jelly, restoring the damaged portion to their original condition using required materials, fixing the water closet to perfect level, alignment, testingetc.complete. 37 providing and keeping in stores, shifting to the place of installation, fixing, testing and commissioning ofwhite coloured vitreous china under counterregular rectangular wash basin with brackets / g.i. rag bolts and nuts painted, 32mm dia brass c.p. waste coupling, ( heavy ) 32mm diabrassc.p.bottletrap, 15mmdiabrassc.p.anglestopcockwith flange, 15mm dia brass c.p. coldwater connecting pipe, etc., the work shall include, required extension nipples, cutting / chasing and making good the walls and floors toilets. wash basin 38 supplying and fixing of pvc water storage tank of best approved quality and make of super thick with lid ofcapacity of 1000 litres with accessories including giving necessary connection etc., complete as directed by the departmental officer. ( the pvc water storage tank should be got approved by the engineer before use on work ) ( twad pano:173 ) 39 septic tank 40 earthwork for foundationsand depositing on bank with initial lead of 10 mt. and initial lift of 2 mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soilincluding excavated earth. 41 laying the plain cement concrete 1:4:8 ( one cement four sand and eight brokenmachine crushed stone jelly ) using hbg machine creased machine crushed stone jelly of size 40mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.the rates inclusive of centering , shuttering, strutting, propping, removal of form work if it is required and all leads , lifts and curing etc.. 42 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) 43 brick work in following cement mortar using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 for foundation and basement including curing, etc., complete co 44 reinforced cement concrete 1:1.5:3 mixusing 20mm machine crushed 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding cenetering, shuttering and cost of reinforcement grills placed in position, but including laying, vibrating, curing and finishing, fixing fan clamps in the rcc floor and roof slab works wherever necessary and bearing surfaces of the wall at the sides and bottom of the slab, beams shall be finished smooth with cement mortar 1:3 ( one cement and three sand ) and kraft paper laid without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers. 45 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally and externally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or champhering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labour complete in all respects including all lead, lift and descent andas directed. 46 supplying and fixing in position c.i.manhole covers ( heavy duty ) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6x0.6m size etc., complete. 47 providing, machine mixing and laying on the p.c.c / r.c.c. surface in approved panels of25 mm thick granolithic flooring in cement concrete mix of 1:2:4 ( 1 cement: 2 sand: 4 aggregate 10 to 12 mm thick ) well vibrated, compacted including 45 x 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well covered and protected against excess of an type. ( the contractor to provide for preparation of surface by cleaning 48 supplying, fabricating and placing in position mild steel / ribbed tor steel rods for all rcc works including cost of steel and binding wire also in all floors, complete complying with standard specfication. 49 electrical arrangements 50 light / fan point sd 25 51 plug point sd 38 52 concealed power plug point sd 40 53 ceiling fan sd 106 54 exhaust fan sd 114 55 4 18w crystal glass led tube light fitting 56 tneb meter board 57 service connection sd 66 58 earth connection sd 74 59 provision for furniture 60 name board and photographic charges 61 provision for geotechnical investication report & dpr 62 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : November 28, 2023

Tender Value : ₹ 39.68 Lakhs

View Tender
34
Public Works Department - Tamil Nadu

40740151 tender for special repairs to dustbin in pwd campus at chepauk, chennai 5.; 1 repairing the old and damaged gi dust bin of size 1.200m x 1.00m x 1.200m height, cutting the corroded and rusted portion with aid of ag 4 cutting mechine and buffing the all rust and dust area, welding new gi 16 gauge sheet in the cut out area with aid of 10 gauge electrode , replacing the damaged side sheet with new one , removing the old damaged wheel and welding 200mm dia heavy duty black polyethene rubber moulde wheel fitted with gi clamp ball bearingroller assembly 4 nos in the bottom corner’s of the dust bin , welding new 40x 40x6mm angle x 3 nos in the bottom of the dust bin for extra stiffener, painting one coat anticorrosive mrf primer and two coat alluminium paint , conveying the dust bin to the site with complete satisfaction of officer incharge. 2 supplying gi dust bin of size 1.200m x 1.00m x 1.200m height with 1000 lt capacity , cutting the gi 16 gauge sheet to a required size and bending the sheet in the power nemotic bending mechine of required shape, welding and assembling the dust bin with aid of 10 gauge electrode, connecting the side and bottom potion without any gaps in the bottom and welding rigidly, welding top beading alround the dust bin for extra stiffner with necessary ribs with equal interval and welding side lifting area box assembly of size 0.45 x 0.300m on both side of the dustbin with 60mm dia pipe of 2mm thick welded one end in the lifting assembly and other end with 5mm thick 80mm dummy plate as stopper and fixing 200mm dia heavy duty black polyethene rubber moulde wheel fitted with gi clamp ball bearingroller assembly 4 nos in the bottom corner’s of the dust bin, painting one coat anticorrosive mrf primer and two coat alluminium paint , conveying the dust bin to the site with complete satisfaction of officer incharge. 3 renewing the old and damaged mild steel ladder with new one using 80 x 40mm hollow box section as outer side frame and 32 x 32mm hollow box section step frame of width 0.45m x 0.22m and welding gratting flatusing 25 x 3mm over the step in cross rigidly with aid of 10 gauge electrode , erecting the structure in the 1st floor with necessary landing arrangement connecting vertical leg support from the ground levelusing 75 x 75 hollow box 4.00m ground level , fixing the landing arrangement in the ground in the depth 0.45m x 0.330 x 0.330m with 1:2:4 cement concrete in the four leg, supporting the staircase in the wall with base plate and rawal anchoring bolt of size 75mm x 16mm , welding 50mm handrail on both side of the staircase using 50mm dia vertical post, 50mm dia top rail and25mm dia 2 row intermediate , erecting the same in the site and painting one coat primer and two coat synthetic enamel paint with complete satisfaction of officer incharge....

Due Date : November 24, 2023

Tender Value : ₹ Ref. Documents

View Tender
35
Rural Development And Panchayats Department - Tamil Nadu

40740138 tender for proposed construction of building for hsc building at nemili panchayat.; 1 proposed construction of building for hsc building @ nemilipanchayat 2 clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 3 earthwork excavation for foundation ( for narrow excavation ) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification. 4 supplying and filling in foundations and basement with fillingm sand in layers not exceeding 15 cm. thick, well watered , rammed and consolidated etc. complete complying with standard specifications. 5 plain cement concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. 6 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 7 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete 8 supplying and erecting centering and shuttering 9 upto basement 10 ground floor 11 providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of m25 grade for reinforced cement ratio with plasticizer using 20mm and down concrete structural elements under controlled water graded machine broken granite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart mental officers comple. 1m3 12 foundation & basement 13 ground floor 14 steel fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 15 brick work in following cement mortar 1:5 using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4 for foundation and basement including curing etc., complete complying with standard specification. including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the engineer in charge. 16 foundation basement 17 ground floor 18 brick partition walls of 11.50cm thickness using best quality country bricks of size 83 / 4 x 41 / 4 x2 3 / 4in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) . 19 groundfloor 20 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor 21 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed 22 paving the floor with best quality vertified tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.776 / sq.m 23 flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) .basic cost rs.464 / sq.m 24 dadoodling the walls with colored glazed tiles approved size, quality and color set in cm 1:2 10 mm thick. and pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 kg / sqm etc. complete. basic cost rs.318 / sq.m 25 paving the floor with pre polished concrete anti skid step tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) . 26 providing, fabricating and fixing m.s. grillswindows, and ventilator, gates, ladders, rail pipes, nosing angles, with m.s.lugs in staircase steps etc., made out of m.s rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the engineer. 27 manufacturing, supplying and fixing of stainless steel handrails for staircase using 50mm dia 304l grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete.the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, ect.complete 28 supply and fabrication of upvc doorincluding cost and conveyance of all charges etc complete. 29 solid pvc door shutters toilet door using 19 gauge 19mm ms square tubes for styles and outer frames.15mm ms square tubes for top, lock and bottom rails.the steel tubes shall be covered with 5mm thick solid pvc sheets.shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings.the over all size of styles shall be 50mm x 30mm.the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.the over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. 30 upvc windowsupplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g / 1mm 125gsmand 100% corrosion free, the profiles are multi chambered sectionwith wall thick of 2mm. the epdm rubber ( black color ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power points locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed or plainglass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and shouldhave key lockable action, security protective hinges, strong lockingsystems and as per sizefor arrestingnoise and energy loss. 31 upvc ventilator: supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with gi / 1mm 125gsmand 100% corrosion free , the profile are multi chambered sections withwall thick of 2mm. the epdm rubber ( black color ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. the ventilator should be got approved from the executive engineer before use on work. 32 painting two coats of synthetic enamel paint of approved colour and make over one coat of anti corrosive zinchromite primerover new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications. 33 supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the wallssmooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. ( the colour and shade of the distemper shall be got approved by the executive engineer before use of work ) . 34 weathering course concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( no sand to be used ( over the rcc roof slab in the proportion of brick jelly to lime being 32 : 121 / 2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed 35 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 36 supplying and fixing in position best approved quality ( oriya type ) white indian type water closet530 mm x 440 mm white glazed earthern ware of approved quality and brand with p or s trap conforming to bis with sand cushion and forming flooring alround the closet using 40 mm broken brick jelly in lime concrete 1:2:5 ( one lime, two sand and five brick jelly ) 100 mm thick and finishing the top to the required slope and including giving necessary connection to ci soil pipes ( including the cost of 100mm dia ci pipe for a length of 600mm ) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officer. 37 supplying and fixing of indus floor mounted white colour european water closet 38 wash basin 39 1000lit 40 pipe line arrangements 41 earthwork for foundationsand depositing on bank with initial lead of 10 mt. and initial lift of 2 mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soilincluding excavated earth. 42 laying the plain cement concrete 1:4:8 ( one cement four sand and 43 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed 44 brick work in following cement mortar using best quality of country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 for foundation and basement including curing, etc., complete complying with standard specifiction. 45 reinforced cement concrete 1:1.5:3 mixusing 20mm machine crushed 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding cenetering, 46 supplying and fixing in position c.i.manhole covers ( heavy duty ) mof various sizes of best approved quality and as per standard specificationsetc., complete.0.6x0.6m size etc., complete. 47 providing, machine mixing and laying on the p.c.c / r.c.c. surface in approved panels of25 mm thick granolithic flooring in cement 48 light / fan point sd 25 49 concealed light point sd 26 50 plug point sd 38 51 concealed power plug point sd 40 52 ceiling fan sd 106 53 exhaust fan sd 114 54 4 18w crystal glass led tube light fitting 55 tneb meter board 56 service connection sd 66 57 earth connection sd 74 58 provision for geotechnical investigation report & dpr 59 name board and photographic charges 60 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package } ...

Due Date : November 28, 2023

Tender Value : ₹ 39.68 Lakhs

View Tender
36
Municipal Adminitration And Water Supply Department - Tamil Nadu

40736262 tender for construction of toilet blocks at hindu higher secondary school in ward no 11; 1 earthworkexcavationfor foundation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary, refilling the foundation with excavated earth and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers. 2 earthwork openexcavationin all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15 cm thick layers well rammed and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers. 3 supplying and filling in foundation and basement with filling m sand in layers of not more than 15cm thick well rammed watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers. 4 refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification 5 supplying and filling of gravel in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the dept., officers with standard specification. 6 supplyingandfilling 40mm iss metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc., complete ( the rate including cost of metal filling etc., complete complying with standard specification. 7 supplyingandfilling 20mm iss metal in dispersion trench around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc., complete ( the rate including cost of metal filling etc., complete complying with standard specification. 8 plain cement concrete 1:4:8 ( one part of cement, four part of crushed stone sand ( m sand ) and eight part of coarse aggregates ) using 40mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification 9 providing and laying in position, standardised concrete mix m 20 grade in accordance usingwith is:456 2000, 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg / m3 and maximum water cement ratio of 0.55, including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5cu.m. ) 7730 kg. of 20mm machine crushed stone jelly and with about ( 3.3 cu.m. ) 5156 kg. of 10 12mm machine crushed stone jelly and with about ( 4.79 cu.m. ) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requirements of is standards. ( no separate payment will be made by the department for the excess usage of materials ) .foundation & basement 10 superstructure in ground floor 11 supplying, fabricating and placing in position of steel reinforcement using ms ( or ) rts rods for all rcc item of works including cost of steel and binding wire in all floorsetc., complete complying with standard specificationand as directed by the departmental officers. 12 supplying and erecting steel centering including necessary supports for plane surfaces, in foundation and basement for all rcc works such as column footing, plinth beam, grade beam staircase step, bedblock etc., which requires only normal strutting using ms sheets of size90cmx60cm of bg 10 stiffened with mild steel angles of size 25mmx 25mmx3mm laid over silver oak ( country wood ) joists of size 10cmx6.5cm spaced at about 90cm c / c and supported by casurina props of 10cm to 13cm dia. ( spaced at 75cm c / c ) etc., complete complying with standard specification and as directed by the departmental officers. ( the centering will be removed after specified period of concrete without damaging the concrete ) 13 supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at above 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. ( payment for centering shall be given after the concrete is laid ) for plane surface 14 for plane surface such as rcc square or rectangular column, top and bottom slab of sunshade, boxing, sill slab etc., 15 brick work in cm 1:5 ( one cement & five crushed stone sand ( m sand ) ) using ii class ground moulded bricks of size 9 x 43 / 8x 2 3 / 4 including finishing, curing, etc., complete complying with standard specification 100cft in foundation & basement 16 in superstructure in ground floor 17 brick work in cement mortar 1:3 ( one cement and three m sand ) using iind class ground moulded chamber burnt bricks9x43 / 8x2 3 / 4 and finishing neatly curing etc., complete complying with standard specificationsand as directed by the department officers. ( masonry projections wherever necessary for obtaining required elevation shall be done without extra cost ) foundation & basement 18 brick workpartition wall 11.10 cm thick using secondclass ground moulded chamberburnt bricks ofsize 9x 4 3 / 8”x 2 3 / 4”in cement mortar 1:3 ( one cement and three sand including fixing hoop iron reinforcement if found necessary, laying, finishing and curingand including plastering in cm 1:5 ( one cement and five sand ) 12mm thick on both sides etc., complete complying with standard specification and as directed by the departmental officers.for superstructure in ground floor 19 manufacturing, supplying and fixing precast reinforced cement concrete slabs of following thickness in rcc m20 concrete using following hbgs jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed. 20 special ceiling plastering in all floors and finishing the exposed surface of rcc items of work such as slab, beam, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 ( one cement and three m sand ) 10mm thick including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase, step, landing slab etc., including neat finishing and curing etc., complete complying with standard specification and as directed by the departmental officers. 21 plastering with cement mortar 1:5 ( one cement and five m sand ) 12mm thick in all floors using fine river sand including neat finishing, curing, etc., complete complying with standard specificationand as directed by the department officers. 22 plastering with cement mortar 1:3 ( one cement and three m sand ) 20mm thick with wpc 2% by weight of cement used in all floors using fine river sand including neat finishing, curing, etc., complete complying with standard specificationand as directed by the department officers. 23 painting the walls two coats with best oil bound distemper of approved quality ( to be approved by the executive engineer before use on works ) over one coat of primer for newly plastered wall including preparation of surface and finishing neatly including cost of all materials, brushes, scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers. 24 painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first quality and of approved colour over a priming coat including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required etc., complete complying with standard specification. 25 paving the floor withcolour designceramictiles of following design of approved quality and colour of size 305 x 305 x 6mmin all floors over a base layer of cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointing with white cement using 0.30kg / m2including adding suitable colour pigments to suit the colour of tiles finishing perfectly and curing etc., including cost of tiles, all materials and incidential charges, transportation charges and labour charges for laying tiles etc., complete complying with standard specification andas directed by the departmental officers . ( the tiles should be got approved by the departmental officers before use on works ) . 26 dadooing the walls with colour design glazedtiles of size 300mmx200mmx6mm of approved quality in all floors set in cement mortar 1:2 mix ( one cement & two sand ) 10mm thick and pointing with white cement using 0.4 kg / m2 including adding suitable colour pigments to suit the colour of tiles including finishing the joints neatlyand curing etc., completecomplying with standard specifications. ( the tiles should be got approved by departmental officers before use on the work ) . 27 supply and fixing of steel doors with single leaf with following specification. ms angles of size 40x40x 6mm at 3.5 kg / m used for the outer frame and ms angles of size 35x35x5mm at 2.60 kg / m for the shutter frames. stiffners with 32x6mm at 1.50 kg / m. ms flat is provided as the lock rail of the door and welded infact of both ends to the shutter frame, 18 gauge cr sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg / m ms flat is welded over the 32x6mm at 1.50 kg / rm and ms flaton the rear side of the door sandwitching the cr sheet for rigidity with locking rail and bottom tie arrangements. additional stiffners with 18x5 mm at 0.7 kg / m ms flats are provided horizontally diagonally on the rear side of the shutter. 2nos of hinges in case of single leaf and 4nos of hinges in case double leaf shutter is provided 6 nos of hold fasts 200 length 40x40x6mm m.s. angle spliced at the ends are welded to the outer frame of the door. 28 supplying and fixing in position of solid panel pvc door with pvc frame. solid pvc door shutter using 19 gauge 19mm ms square tubes for styles and outer frame. 15mm ms square tubes for tops, lock and bottom rails, the steel tubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the over all size of styles shall be 50mmx30mm. the over all size of top rail, lock rail and bottom rail shall be 75mmx30mm. the over all size of frames shall be 50mmx45mm with suitable rabate for housing the shutter. 29 supplying and fixing in position of solid panel pvc door with sliding aluminium frame. the outer frame will be 62x38x2mm @ 1.17 kg / m and 40x20x2mm aluminium c section. soild pvc door shutter using 16 gauge 19mm ms sq. tubes for styles and outer frames. 15mm ms. sq. tubes for top lock and bottom rails. the steel tubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for paneling shall rigidly fixed in position including necessary furniture fittings. the overall size of styles shall be 50mmx30mm. the overall size of top rail, lock rail and bottom rail shall be 75mmx30mm, with suitable rebate for housing the shutter etc., complete complying with standard specification and as directed by the departmental officer. 30 manufacturing, supplying and fixing in positon of rcc jallyin cement concrete 1:2:4 using 20mm machine crushed stone jelly ( excluding cost of reinforcement steel ) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed 50mm thick 31 painting the new iron work with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer. ( thequality and colour of paint should be got approved by the departmental officer before use on work ) . 32 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 33 supplying and fixing in position indian water closet oriya type of size 580x440mm white glazed earthernware of approved quality with p trap or s trap conforming to is 2556 part xii with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly ) 100mm thick and finishing the top to required slope and including giving necessary connection to pvc. pipes by dismantling brick masonry, reinforced cement concrete roof / floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specification and as directed by the departmental officers. ( the oriya type water closet andall accessories should be got approved by the departmental officers before use on work ) 34 supplying and fixing in position white glazed european water closet of best quality and approved make with 100mm p or s trap with double flapped rigid pvc.seat cover with chromium plate brass hinges, including supplying and fixing pvc. low level flushing tank 10 litre capacity of approved quality on wall with teak wood plugs, brass screws and 2 numbers 15mm dia gun metal wheel valve, 15mm dia nylon connection and giving necessary water supply connection as directed by the departmental officers. the rate includes cost of 100mm dia pvc.pipe 60cm long including cost of 3 kg.of white cement 6kg.of cement, spunyarn, shellac, thread ball, teak wood plugs, brass screws 75mmx10mmetc., complete complying with standard specification and as directed by the departmental officers. ( the european water closet and flushing tank should be got approved by the departmental officers before use on work. ) 35 supply& fixing stainless steel health faucet of best quality with control valve as directed by the departmental officer. 36 supplying and fixing in position best quality of approved make white glazed earthernware wash hand basin ( without pedestal ) of size 550x400mm with a pair of cast iron brackets , including cost of 15mm diametre brass chromium plated pillar tap, 32mm diametre c.p.waste, 32mm diametre pvc waste pipe with rubber plug and chain, 15mm diametre gun metal wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of c.i.brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti corrosive paint including testing for leakage etc., complete complying with standard specification and as directed by the departmental officers. ( the wash hand basin and specials should be got approved by the departmental officers before use on work ) 37 supplying and fixing in position indian make bevelled edge mirror of approved quality and brand pvc / fibre glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. ( the mirror should be got approved by the executive engineer before use on woks ) 38 supplying and fixing approved best quality brass cp towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and cp screws, etc., complete complying with standard specifications. ( the towel rail should be got approved by executive engineer before use on works ) . 39 supplying andfixing new one of best approved quality chromium plated soap tray of size 150x150mm of approved quality and brand including cost of rawel plug, brass screws etc., complete complying with standard specification and as directed by the departmental officers. ( the materials should be got approved by the executive engineer before use on works ) . 40 supplying and fixing position p.v.c nahani trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( one part of lime, two part of sand and five part of 40mm gauge brick jelly ) and finished with cement mortar 1:3 ( one cement, three sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the ci / pvc pipes, etc., complete complying with standard specification. ( the nahani trap should be got approved by the executive engineer before use on works ) 41 supplying and fixing best variety and approved quality of pvc ventilating shaft of 110mm dia and 3m height including cost of 100mm dia.pvc cylindrical cowl type and fixing in position as directed by the departmental officers complete complying with standard specification. ( the pvc pipe and cowl should be got approved from the executive engineer before use on work ) 42 supply and delivery and fixing of hdpe tankas per is 12701 / 1996 including loading, unloading, transportation and labourcharges for fixing of the gi pipes andspecials for pipe connection works includingcutting, threading and fixing charges etc., . ( the pvc water tank should be got approved by the executive engineer before use on works ) . 2000 litre capacity. 43 supplying and fixing in position first quality and approved variety of gun metal gate valve with bis make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements ) .the valves to be used on work shall be got approved by the executive engineer before use on work 50mm gate valve 44 40mm gate valve 45 supplying & fixing inposition 15mm dia chromium plated brass screw down tap ( heavy type ) of approved make confirming to iss and including cost of shellac, thread etc., complying with standard specification and including cutting and threading wherever necessary ( tapsshould be got approved by the departmental officers before use on works ] 46 supplying, laying and joining upvc ( designedto handle higher pressure ) pipes of approved quality and best veriety conforming to iss with isi mark, of the the following size above ground level up to 4 m hight laid properly to alignment including cutting, threading and fixing the required upvc specials but excluding the cost of such specials and fixing to the wall with necessary tw plugs, clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plasteringwherever necessary with necessary scaffolding charges etc., complete.25mm dia pipe 47 32mm dia pipe 48 40mm dia pipe 49 supplying, laying and joining upvc pipes ( handle higher pressure ) of approved quality and best veriety conforming to iss with isi mark, of the the following size below ground level laid properly to alignment including cutting, threading and fixing the required pvc specials but excluding the cost of such specials etc., complete.32 mm dia pipe 50 supplying and fixing in position of the following upvc specials best approved quality conforming to iss and providing leak proof joints with upvc adhesive etc., including fixing to walls with necessary teak wood plugs screws etc., and giving connections to the upvc pipe dismantling the brick masonry rcc floor or roof slab and redoing the disturbed portion to original conditions etc., complete complying with standard specifications. the upvc specials should be got approved from the executive engineer before use on works 50mm coupling 51 50mm bend 52 50mm elbow 53 40mm tee 54 40mm elbow 55 40x32mm reducer 56 32x25mm reducer elbow 57 25x20mm reducer tee 58 supplying and fixing in position best quality pvc soil / waste pipes ( 6 kg / cm2 ) of various size having isi mark and providing leak proof joints including fixing to the wall with special pvc / ms clamps, etc., and making connection to all sanitory fittings, dismantling masontry etc., complete complying with standard specification. ( below ground level ) 75 mm dia pvc soil pipe 59 110mm dia pvc soil pipe 60 supplying and fixing in position pvc specials of the following dia and types of approved quality confirming to bis and providing leak proof joints including fixing to the walls and giving connection to the pvc soil stacks, dismantling the masonry or rcc works and re doing the dismantled portion to original condition etc., complete complying with standard specifications. ( the pvc specials should be got approved by the executive engineer before use on works ) .75mm dia pvc door elbow 61 75mm dia pvc plain elbow 62 75mm dia pvc tee 63 110mm dia pvc door elbow 64 110mm dia pvc plain elbow 65 supplying, laying and joining upvc pipes ( handle higher pressure ) of approved quality and best veriety conforming to iss with isi mark, of the the following size below ground level laid properly to alignment including cutting, threading and fixing the required pvc specials but excluding the cost of such specials etc., complete.32 mm dia 66 supplying and fixing in position of the following upvc specials best approved quality conforming to iss and providing leak proof joints with pvc adhesive etc., including fixing to walls with necessary teak wood plugs screws etc., and giving connections to the upvc pipe dismantling the brick masonry rcc floor or roof slab and redoing the disturbed portion to original conditions etc., complete 32 mm diaupvc coupler 67 drilling 150mm dia vertical borewell to the required depth as directed by the departmental officersincluding labour charges inserting pipes assembly in the drilled pit including welding the joints wherever necessary and grouting the casing pipe if necessary in hard rock etc., complete and including transportation charges for the rigs and supporting vehicles from one place to another etc., complete as directed by the executive engineer. 68 supply of 160mm pvc speical casing pipe of best approved quality having pressure of 6kg / sq.cm etc., complete as directed by the departmental officers. the pipe should be got approved by the executive engineer before use on work. 69 supplying and fixing ofm.s . bore well clamp suitable for 40 mm diag.i pipe and 4 nos of 5 / 8 x 2 1 / 2 bolt and nuts. 70 supplyinging and fixing of 50 mm dia stainlesssteelpipe connecter etc., complete as directed by the departmental officers. the pipe should be got approved by the executive engineer before use on work. 71 supplying and fixing and erecting of 3.0 hp submersible pump ( three phase ) of best approved quality and make with isi mark required accessories including panel board dol with two level guard and autostart switch, delta starter, 3 nos bulb and 30 amps switch and wiring from panel board with meter, v belt service wiring with necessary flexible pipe with all required accessories etc., complete 72 supplying and delivery of nylon rope of 18mm dia for holding the submersible pumpset and hdpe pipe etc., complete. 73 supplying and fixing of 3 x 4 sq.mm pvc insulated and sheated 3 core flat type copper cable confirming to is 694 / 1990etc., complete complying with standard specifications. 74 supplying and fixing of cement based hydraulically pressed anti skidtiles ( like eurocon / equivalent ) of size 30cm x 30cm and 30cm x 15cm for flooring of approved quality and colour andset in cement mortar 1:3 ( one cement and three m sand ) 20mm thick and pointing with white cement using at the rate of 0.40kg / m2 including finishing joint with tile surface etc., complete complying with standard specificaiton and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 75 supplying and fixing in position of cast iron man hole cover with ci frames of size 600x600mm heavy duty of best approved quality and as per indian standard specification make etc., complete complying with standrd specification and as directed by the departmental officers. ( the cast iron man hole cover should be got approved by the departmental officers before use on work ) 76 providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 ( one cement, two m sand and four aggregate ) using 25mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. 77 supplying and fixing in position best approved of isi quality of 110mm diameters of pvc rain water down fall pipes having a working pressure of 4 kg / sq.cm including cost of necessary pvc shoe, pvc bend, c.i. gratings of required diameter and special clamps, brass screws, nails etc., and fixing of cast iron gratings at juction of parapet and the rcc roof slab including finishing, neatly etc., complete. 78 supplying and fixing incinerator for ladies bathroometc., complete complying with standard specification and as directed by the departmental officers. 79 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessoires in flush with wall with 3mm thick hylum sheet cover with tw switch box and 5a ft switch and making good of the concealed portion with suitable colour for pvc concealed light / fan point ( for electronic regulator ) ( 5 points per coil ) sd 25 80 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories in flush with wall with 150mm x 100mm x 113mm tw switch box with 3mm thick hylem sheet cover for 5a 3 pin non inter locking wall socket with 5a flush type switch with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed pvc plug point sd 38 81 supply and run of 2 of 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour sd 55 82 supply and fixing of single box type 440w fitting complete with copper choke and condenser with round blocks on wall or ceiling with flu tube with pvc unsheathed copper leads from terminals to the fitting etc, complete as per standards sd 89 pwd electrical data 83 supply and fixing of 1200mm ( 48 ) ac ceiling fan complete with stepped electronic 300w regulator with 1 meter down rod on the existing clamp sd 107 pwd electrical data 84 earting as per pwd standards with an earth electrode of 2mts class b gi pipe of dia 32mm complete with necessary masonry works sd 234 pwd electrical data 85 supply and fixing of 3 phase 4 wire 4 way icdb of 32a per way with 100a tpnmc switch with suitable trunking box ms cable entry boxes and internal connection on suitable angle iron frame work with earth connection sd 178 pwd electrical data 86 supply and fixng of tneb meter board suitable for 3 phase 63a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 / 2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos. 63a fuse units ( 500v ) , 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 16 sq.mm pvc insulated copper wire with earth connection complete sd 129 pwd electrical data 87 supply and fixing of 440w twin street light fluorescent fitting complete with copper choke and condensor with 19mm dia gi pipe ( class b ) with 1 no. 19mm gi bend complete on the existing post / wall with 16a aerial fuse unit on ms plate with pvc unsheathed copper leads with ms clarnps and aluminium painting with fluorescent tubes sd 94 pwd electrical data 88 supply and run of 2 of 2.5 sq.mm ( 36 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100 v grade on 7 / 20 gi wire for service connection mains sd 449 89 supply and delivery 32mm gi service pipe including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specification 90 provision for g.s.t 18%...

Due Date : November 23, 2023

Tender Value : ₹ 30 Lakhs

View Tender
37
Rural Development And Panchayats Department - Tamil Nadu

40713467 tender for construction of passenger shelter at adivaram near sarvodaya sangam sivanmalai house of sivanmalai; 1 construction of passenger shelter at adivaram near sarvodaya sangam sivanmalaih / o sivanmalaiearthwork excavation in all clauses of soils and depositing on bank with initial lead and lift for foundation as per ss20b 2 cement concrete 1:4:8 mix using 40mm iss hbg metal including cost and conveyance of all matials to site and all labour charges etc., complete. 3 collection and supply of gritty gravel from approved quarry including cost and conveyance of all materials to site including all labour charges for fillingetc.complete, 4 supplying & erecting centering for sides & soffits including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists country wood ) of size 10 x 6.5cm spaced @ about 90cm c / c and supported by casuarinas props of 10 13cm dia. spaced @ 75cm c / c etc., complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items 5 centering for below ground level 6 centering for column 7 slab centering 8 sunshade 9 supplying and fabrication steel rainforcementincluding all cost and conveyance etc complete 10 rcc 1:1.5:3 mix using 20mm hbg iss metalincluding all cost and conveyance etc complete 11 fly ash brick work in cm 1:5 mix using fly ash bricksof size 23x11x7 cm for the following including curing etc., complete complying with standard specifications 12 weathering course with brick jelly lime concrete using 20mm brick jelly with pure slacked lime over r.c.c. roof slab in the proportion of 32:12.5 andcharges for mixing , laying , and finishing etc complete 13 finshing the top of roofwith one course of pressed tiles of size 23x23x2cm with cementmortar 1:3 mix and pointed with the same oiled mortar including cost and conveyance of all materials to site and all labour charges etc complete 14 plastering with cement mortar 1:3 mixto10mmthick including cost and conveyance of all materials to site and all labour charges etc 15 plastering with cement mortar 1:5 mixto12mmthick including cost and conveyance of all materials to site and all labour charges etc 16 dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in cement mortar 1:2 ( one cement and two crushed stone m.sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., 17 paving the floor with best approved quality fine polished granite stone slabs of size 1200 x 600 of 18 / 20mm thick of synthetic grey, paradise andsimilar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 ( one cement and three crushed stonem.sand ) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc 18 distempering two coats over new plastered surface using oil bound distemper including cost and all labour charges etc., complete 19 painting two coats overnew plastered surface using approved quality of exterior emulsionpaintincluding cost and all labour charges etc., complete 20 painting two coats over new iron works such asdoors windos, etc., with best approved best quality of synthetic enamel paint of approved colour over the existing priming coat etc., complete complying with standard spe 21 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 22 supply and fixing rain water pipe 110mm dia pvcincluding cost and conveyance etc complete 23 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick with painting of suitable colour for open light point sd 21 24 wiring with 2 x 2.5 sq.mm pvc uncheated sc alu.cable of 650v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with 150 x 100 x 113mm t.w. switch box in flush with wall, covered with nylon sheet of 3mm thick 5 amps 3 pin plug point. sd 36 25 supply and fixing of fancy glass shade and 11w cfl for bh point [ sd80 ] 26 supply and fixing of 25w led street light fitting with led ( lower end ) with 19mm dia. gi pipe ( class b ) with 1 no.19mm gi bend complete on the existing post / on wall with pvc unsheathed copper leads with ms clamps and with painting . sd. 533 27 supplying and fixing of aluminium dye cast letters of approved size and colour. the colour treatment process is achieved with mrf colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes 28 6 size letter 29 9 size letter 30 gst amount for providing service to government contract works for the above construction & maintenance works. { gst amount is the total gst amount for overall quoted amount ( both construction and maintenance ) above this row in column bb for all works in this package } ( refer clause 13.2 & 13.3 of section 2 of instruction to bidders ( itb ) of sbd ) ...

Due Date : November 24, 2023

Tender Value : ₹ 15 Lakhs

View Tender
38
Tamil Nadu Transmission Corporation Limited - Tamil Nadu

40686815 tender for supply, fabrication, sand blasting and painting of rs joists, 12mm base plate of control cable and termination etc. for erection of 1 no. 110 kv feeder breaker with allied equipements to operate the 110 kv incoming sources independantly from alamathy 400 / 110 kv ss and mosur 230 / 110 kv ss at kakkalur 110 / 33 11 kv sub station...

Due Date : November 29, 2023

Tender Value : ₹ Ref. Documents

View Tender
40
Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

40678167 supply of inner cone assembly with access door and inside ceramic lining suitable for xrp 803 mills , supply of inner cone assembly with access door andinside ceramic lining suitablefor xrp 803 mills size of inner cone: as per enclosed drawing. material : base plate material: is 2062 gr a base plate thickness: 10 mm thicknessinner: ceramic lining tiles ( 12mm thickness ) ceramic tiles specification: al2o3 85% min;hardness 8 to 9 mho scale bulk density 3.2 to 3.3 gm / cm3 water absorption less than 1 %. weld plug : one end mounted on base plate and other end with ceramic tiles ( actual dimensionsmay be taken at site ) ...

Due Date : December 04, 2023

Tender Value : ₹ Ref. Documents

View Tender
41
Southern Railway - Tamil Nadu

40671809 auction sale of cond. & u/s ferrous scrap in corroded nature such as head stock, foot steps, berth frame, roller shutters, corroded/ dinged/ damaged wagon door, zinc coated fs sheets, base plates, ms/gi sheets in full/cut/damaged/rusted/corroded/crushed condition, wagon floor sheet, coach door ,sliding door of various sorts & sizes, battery boxes, battery box door, collapsible gate, punches plate/ sheet/ screen, corroded shear cutups, roof light/tube light fitting with/without ballast, fl housing, tl patti, cfl frame, regulator box, ms gutter, corroded fabrication scrap, carriage fan body cover/end shield/ guard/ blade, pedestal fan guard, air brake pipes, corr. barrels/paint drums, silent block, anchor block, wires, chains, boxes, hoop iron, lamps, wall protector, trough sheets, air filter, clips, panels, corroded gi pipes with/without valves, gi duct, ci covers, corroded/ damaged/ dinged condition coach/wagon cutup parts, sheets, equalizing stay, brake anchor, pre cooling outer enclose, corroded round/square pipes, pipe wrench in corroded condition, commode chutes, pins, rivets, bolts, nuts, small iron pieces, wire rope/safety rope with/without aluminium sling, box type fitting, antenna mounting pipes, shell of window ac of various sorts, dust bin, hood, grs box, m.s pipes of various sizes, card rack, bond, hs lamp, battery charger core with iron stand or frame, iron core, fl patti & fitting of all types and sorts and sizes, fire extinguisher without cap, fan down rod, ferrous ac template, train information display system, packing strips, battery tray, trough floor sheets, radiator bracket, empty charger without nfs attachments (ferrous) and any other ferrous items of highly corroded nature released from carriage/wagon/loco rolling stocks and all the above items are of various sorts and sizes in full/cut/broken and with/without wooden/glass/ rubber/ fs end fittings with /without minor non ferrous attachments if any in as is where is condition.note: 1) cutting is permitted to loadable size and for heavy nature items only.2) during delivery if any major non ferrous items found the same may be handed over to custodian. pl no.98090800...

Due Date : November 23, 2023

Tender Value : ₹ Ref. Documents

View Tender
42
Southern Railway - Tamil Nadu

40671798 auction sale of cond. and u/s ferrous fabricated materials of ms/ci scrap in nature such as weld mesh, ms duct, anti slip arrangement, earthen bond, galvanized (gi) sheet, ms sheet of various sorts and sizes, blower rotary forging, liner, guide fixtures, side frame fixtures, trolley of various sorts and sizes, trolley wheel & frame, battery fixing iron tray, panel board, distribution board, ms pipe, coach/wagon stand, dismantled lift items, conveyor belt, ferrous body of auto change over panel, wire mesh, emu coach cut parts, ferrous portion of cab window assembly, sign on iron stand, salary bin, cupboard, structural items, different type of packing channels, ms benches, hydralic rail bender,ferrous portion of window ac plant & water coolers, hand trolley, centrifuge for car body,car body filter,hoist double line base instrument base & cover,fm diode block instrument front &back cover, undersling water tank, sand box, aduppu, flat, trough sheet, coach cut up parts, ms tank, grill gate, rolling shutter, bench test, wheel with plate, bins, roller of shutter, regulator empty box, sliding doors, dolley,platform shelter, engine base rail of demu, collapsible gate, fob fencing, corrugated sheets, rectangular square tube &galvanised sheets, bogie mounted brake beam with composite brake blocks, gi sheets, pipe 8(ductile)inside thin layer of concrete in full pipe&negligible quantity of rubber beeding, square &rectangular tubes & galvanised sheets, ms grill gate,grill window &stair case handle,ferrous body of various types of motor, angle and channel fabricated with nut, bolt,ladder,plate,grill, barricade, bolts, nuts, tray under frame, trailer frame, frame, empty bin, pipe bending machine, hydraulic extractor, ci pipes, hume pipe, doors, side walls, platform pedestal, light post, boxes, front load buckets, cut rod, rails of various sorts and sizes with/without concrete/brick/mud adhering, enclosures, tank in full/cut pieces, battery tray, ladder, all types of trolley wheels with minor nfs attachments, screens, channel post, sheets, stand, track machine cut up parts, ms pipes covered with or without rope &with or without parts of rubber, dome, vrla rack, vcb in dismantled condition, vrla battery box & clamp, stand, dtmf way station equipment box, led line display board, hydraulic lifting table with available fittings, vrla battery empty container, bed/base plate, fabricated cut rods,gi pipes, angle, plate, platform bench, spring plank, clamps, cabinet, ms grill, sheets, ladder, ms water tank, fire tender tank, sand box, fencing, tl rod, vcb panel, train display board, battery stand, boards, tools box, empty regulator &empty battery container, cut rod, ticket punching cut parts, hand rail, fabricated post/pipe/rod, strips, hoods, impellor, base plates, meshes, battery box frame, grs box, control panel, fan down rod, ac window covers ,angle / channels with/without rails, angle of tld, rack, s&t panels, main switch panel board w/o nfs attachments, ebc & rbc frame &enclosure,emu sliding door, high beam, silencer, , garden light post, tap changer cover with fiber attachments, empty battery container, stretcher, cupboard, dust bin, iron step, empty rotary junction box, empty regulator box, iron metal box, garden light post, stand, mdb w/o non ferrous attachments, st light tubular post, gi/ms window, luggage rack, bed portion of weighing scale l with or without any minor non ferrous attachments and all other scrap excluding ms hand hold in fabricated nature of sorts and sizes full/broken with/without other fs/ci/gi fittings in as is where is condition.pl no 98050126note:(1) cutting is permitted to loadable size and for heavy nature items only.2) during delivery if any major non ferrous items found the same may be handed over to custodian....

Due Date : November 23, 2023

Tender Value : ₹ Ref. Documents

View Tender
43
Town Panchayats - Tamil Nadu

40662328 tender for maintenance of community hall in vadugapatti town panchayat, erode district.; 1 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.61 v vi, ( via ) 3 2 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification and as directed by the deparmental officers 44 h v, vi, ( s5a ) vii , 3 3 paving the floor with pre polished concrete anti skid tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 39 a 4 supplying and painting the new plastered walls with two coats of exterior emulsion paint ( weather proof ) first class quality and of approved colour over a priming coat including thorough scrapping clean removal of dirt etc. complete and including necessary plaster paris putty etc. wherever required.as per ( isi std ) ( it mustprovide excellent resistance against the growth of algae and fungi on the walls. and it must offer excellent protection against alkali and uv degradation and the durability period should be 5 years. 61 v, vi ( s4 ) 3 5 providing upvc ( un plasticized polyvinyl chloride ) door: providing and fixing casement doors fabricatedfrom un plasticized polyvinyl chloride ( upvc ) sections.profiles: the profiles should be three chamber system which provides high insulation properties with outerframe 60mm x 55mm with an outer wall thickness of2.4mm. the window unit should be designed with allcorner joints mitred and fusion welded. windowsshould be steel reinforced with 25 x 24 x 25mm steelreinforcement with a thickness of 1mm to havedimensional stability. the sash should be of 60 x102mm. the mullion should be of 60 x 74mm. theprofiles should have co extruded seals.hardware: all the hardware like friction stays, handlesshould be screwed with self tapping screws. thehandles, locks should be designed so that they cannotbe released from outside.glazing: the window system should beglazed with5mm plain float glass / 6mm bison laminstallation: the profiles should be cut to length andwelded 45 degrees. the window should bedesignedsuch that the water drainage does not pass throughthe reinforcement chamber. the window systemshould be fixed directly to the plastered brick wallusing self expanding nylon plug and driving mselectroplated screws into plug. pwd sor page no : 65 sl. no : 268 6 supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 25gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work page no : 65, sl no: 265 7 supply and fixing of m.s grills for windows, with one coat of red oxideprimer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specification. including phosphating as per isi with rust preventive primer & ready to assemble condition for easy installation at site including dismantlingmaking necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. and steel doorcomplete as directed by the departmental officer. 8 supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mmboth profiles are reinforced with gi / 1mm 125gsm and100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( blackcolour ) covered with all over the edges of frame and shutter.the corners and joints should be welded and cleaned.radiations pin headed glass 4mm thick should be provided inthe louvers. the window should be fixed to the wall with100% packing with screws and silicon packing all round theframes. the ventilator should be got approved from theexecutive engineer before use on work pwd sorpage no : 66 9 painting the new iron works such as steel doors, windows, ventilators windows bars, balustrades etc, in all floor withtwo coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand ( to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc, complete complying with standard specification. ( the make, quality and colour of paint should be got approved bythe engineer in charge before use on works ) ( tnss no or nbc no 61 v vi ( 54 ) 3 ) 10 supplyingandfixingin position best approvedof bis quality 110mm p.v.c rainwaterdownfallpipe having a pressure of 4kg / sq.cm including cost of necessary pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc, and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc, complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of uclamp at the centre of the pipe line in addition to those for more than 3.00mt pipe length etc, completecomplyingwithstandardspecifications. 11 dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in cement mortar 1:2 ( one cement and two sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.. 39 a 12 manufacturing, supplying and fixing of stainless steel hand rails for staircase near wet riser using 50mm dia 304l grade stainless steel pipe of 1.60mm thick will be provided with tubular supports made of 304l grade stainless steel pipe of 25mm dia of 1.60mm thick welded to the railing. the supports will be grouted into the wall and provided with 93.00mm thick stainless steel circular base plate of 304 grade. the rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete page no : 62 m 0652 13 supplying and fixing in position white / colour glazed european water closet of best quality and approved make with 100 mm p or s trap connecting with ci pipe of 100mm dia / pvc pipe of 110mm dia, double flapped rigid pvc black seat and seat cover with cp brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity pvc / 12.5 litres capacity porcelin low level flushing tank with a pair of ci brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white pvc flush hand using indian adopter joint including all internal fittings uch as 15mm brass connections, 15mm gm wheel valve, 15mm brass nipple ( 2 nos. ) , 15mm nylon connection, tw plugs, screws and also giving necessary connection to the pvc pipe including cost of 600mm length of 110mm dia pvc pipe and painting the ci brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re doing the dismantled masonry to original condition etc. complete complying with standard specifications. ( the ewc and flushing tank wiht all accessories should be got approved by the executive enginer before use on works ) 14 supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm ( with pedestal / without pedestal ) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. ( the wash hand basin and specials should be got approved by the executive engineer before use on works ) . 15 polishing the teak wood door with two coats of best french ( lac ) polish with approved quality and brand over a coat of bees waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. ( the make, quality and colour of french polish, bees vax should be got approved by the executive engineer before use on works. ) 16 wiringwith2 x 1.5 sq.mm ( 22 / 0.3 ) pvcinsulatedsc unsheathed cu. conductor of 1100v grade in cuitable pvc rigidpipe concealed in wall and ceilingwithpvcaccessoires in flushwith wall with 3mm thick hylum sheet cover with tw switch box and 5a f.t. switch and making good of the concealed portion with suitable colour for pvc concealedlightpoint / fan point ( for electronics regulator ) ( sd no: 25 ) 17 wiringwith2 x 1.5 sq.mm ( 22 / 0.3 ) pvcinsulated sc unsheathed cu. conductor of 1100v grade in suitable pvc rigidpipe concealed in wall and ceilingwithpvcaccessoires in flush with wall 150mm x 100mm x 113mm tw switch box with 3mm thick hylum sheet cover for 5a 3 pin non inter locking cs plug with continuous earth wire connection of 14swg tc wire and making good of the concealed portion with suitable colour for concealed pvc plug point ( sd no: 38 ) 18 wiring with 2 x 4 sqmm ( 56 / 0.3mm ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable heavy gauge ms conduit pipe on wall and ceiling with ms accessories inflush with wall with 150mm x100mm x75mm ms switch box concealed type with 3mm thick hylum sheet cover for 15a 3pin flush type non inter locking cs plug with continuous earthwire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed power plug point.etc, complete as per standard specifications. sd 40 19 supplying and fixing of 3 phases 4 wire 4 way icdb of 32 amps per way with 100 amps tpn mc switch with suitable trucking box. ms cable entry boxes and internal connection on suitable angle iron frame work withearth connection [ sd 178 ] 20 supplying and fixing of horizontal type 4 way triple pole natural mcb distribution board in sheet steel enclosure with 40 amps 4 pole mcb isolator as incoming and 12 nos.6a to 32 a mcb as outgoing in flush with wall and making good of the concealed portion with earth connection. [ sd 179 ] 21 earthing as per pwd standard with an earth electrode of 2 m class ‘b’ gi pipe of diameter not less than 32 mm complete with necessary masonry work. [ sd 234 ] 22 wiring with 2 x 4 sq.mm. ( 56 / 0.3mm ) pvc insulated sc unsheathed copper cable conductor cable of 1100v grade in suitable heavy gauge ms conduit pipe on wall and ceiling with ms accessories with 150mm x 100mm x 75mm ms switch box for 15a 3 pin non interlocking cs plug with painting of suitable colour with continuous earth wire connection by 14 swg tc wire for open power plug point [ sd 13 ] 23 supplying and run of 2 of no. 8 swg gi wire for guarding with cradle withno 8 swg gi wire at an equal interval of 1.5m [ sd 75 ] 24 supplying and laying of 3½ x 50 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 m putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ sd 206 ] 25 supplying of 4 x 10 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 m putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ sd 202 ] 26 supply andrun of 2x 4 sqmm ( 56 / 0.3 ) pvc insulated sc unsheathed cu. conductor of 1100v grade in 25mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains on 7 / 20 gi bearer wire for service connection mains ( sd. no 70 ) 27 supply andfixing of 32 amps dp switch with metal glad of 500v with fuse and nuetral ( side handle ) on suitable tw box pwd earthing ( sd. no 143 ) 28 supply and fixng of tneb moter board suitable for 3 phases 63a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 / 2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos 63a fuse units ( 500v ) 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 7 / 16 pvc insulated copper wire with earth connection complete ( sd no :129 ) 29 supplying and fixing of single box type 2 x 20 w led light fitting complete with electronic choke and teakwood round blocks on wall or ceiling with fluorescent tube with pvc unsheathed copper leads from terminals to the fitting. [ twad sor electrical page no ; 193 sl. no : 15b ] 30 supplying and fixing of450 mm ( 18” ) sweep ( light duty ) ac exhaust fan complete without provision of hole in the wall [ sd 118 ] 31 supplying and fixing of 1200mm ( 48” ) sweep ac ceiling fan complete with stepped electronic 300 w regulator, with 1 m down rod with fan clamp with side plates and cross arm of size 450 mm ( 18” ) [ sd 106 ] 32 supplying and fixing of wt bulk head fitting guard ( philips / bajaj / crompton / k.lite ) suitable for incandescent lamp with 60 w bulb [ sd 84 ] 33 supply and delivery offollowing pvc pipes and specials from borewell to hdpe tanklaying below ground level and above ground level and hdpe tank to toilet . 32mm pvc 10kg / cm2 34 32mm pvc.elbow 35 32mm pvc. bend 36 32mm pvc. tee 37 32mm pvc. end cap 38 20mm pvc 10kg / cm2 39 20mm pvc. bend 40 32mmx20mm pvc.reducertee 41 20mm pvc. tee 42 32mm g.m. gate valve 43 supplying and fixing in position 15mm dia brass cp screw down tap / pillar tap ( heavy duty ) of approved make conforming to bis specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. ( taps should be got approved by the executive engineer before use on the works ) 44 supplying and fixing positionpvc nahani trap ( pvc nahani trap of size 100 x 75mm ) with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( one part of lime, two part of sand and five part of 40mm gauge brick jelly ) and finished with cement mortar 1:3 ( one cement, three sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the ci / pvc pipes, etc., complete complying with standard specification. ( the nahani trap should be got approved by the executive engineer before use on works ) 45 supplying and fixing in position best quality p.v.c soil / waste pipes ( 6ksc ) of various sizes having isi mark and providing leakproof joints including fixing to the wall with p.v.c / m.s clamps etc., and making connection to all sanitaryfittings, dismandling masonry / r.c.c. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications. 110mm pvc 4ksc pipe 46 110mm pvc elbow 47 110mm pvc tee 48 supplying and fixing of 2000 liters capacity hdpe tank with is specification is 10701 / 96 the tank is meant for outdoor ( or ) indoor use complete with removable hinged top locking arrangement and to make provision to fix water supply pipe lines, necessary man hole with cover and including all pvc specials pugs, screws nails to fix the tank etc., complete and the tank should fixedfirming as directed by the departmental officers.the rate shall be inclusive of all materials, labour conveyance hoisting and fixing charges etc. ( the water tank should be got approved by the eebefore use on work. { twad page no ; 89 } 49 earth work excavation for foundation in all types of soils and sub soils to full depth ( such as soils in rock / silt / light black cotton soil / ordinary soil ) except in rock requiring blasting but inclusive of shoring, shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth other than sand in layers of 150 mm thick well rammed and consolidated, depositing the surplus earth in places shown by the departmental officers with initial lead of 10 m and initial lift of 2 m. complete as per tnss23 & 24, v, vi ( s2 ) , vii, 9, 10 50 lain cement concrete of mix 1 : 4 : 8 ( one part of cement four part of sand eight part of aggregates ) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. tndss no: 28 v, vi ( s2 ) v, vi ( s5a ) vii 51 supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing, coloumn pedestals, plith beams, grade beams, staircase steps, etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification without strutting. ( tnss no or nbc no 30 ( s ) 86 86 a v, vi ( s3 ) vii 52 vibrated plain cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. ( the rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers 30 v, vi ( s5 ) vii & 13 53 providing and laying, spreading and compacting graded stone aggregates to wet mix macadam 250mm thick specification including premixing the materials with water at omc in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in sub base / base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of morth 54 providing and laying of 83mm thick high strength type conforming is 15658 2006 of rubberized interlocking paver block in required sizes of minimum compressive strength of 40 n / mm2 in uniform shape of approved make to be laid in flurrying bone pattern with approved non sticking surface in the top and the rate including leveling the base preparation of sub base with stone dust cushion 100mm thick, laying out the pavement cut the pieces to fit the edge, vibrating the pavers, sweeping transporting, loading unloading and laying of paver block as per standard specification. 10 sqm...

Due Date : November 23, 2023

Tender Value : ₹ 20 Lakhs

View Tender
44
Town Panchayats - Tamil Nadu

40560341 supply for stainless steel dustbin with stand in vaitheeswarankoil town panchayat , stainless steel dustbin material stainless steel colour silver model no ss 202 shape round no of pole single type of product open top dustbin size 12*28 inch thickness 0.5 mm pole height 30 inch pipe size 1.5 inch round pipe, 3 mm thickness base plate 5*5 inch plate, 3 mm thickness usage outdoors and indoors...

Due Date : November 09, 2023

Tender Value : ₹ 1 Lakhs

View Tender
45
Town Panchayats - Tamil Nadu

40537453 general fund 2023 24 supply for plastic flexi bin and stainless steel dustbin with stand in velankanni town panchayat supply for plastic flexi bin and stainless steel dustbin with stand in velankanni town panchayat , plastic flexi bin raw material high grade hdpe plastic high density poly ethylene capacity 80 ltr bottom dia 370 mm top dia 480 mm height 710 mm weight 1.950 kg thickness 3.5 mm colours blue and green usage / application outdoors and indoors structure open top shape cylindrical type garbage bin , stainless steel dustbin material stainless steel colour silver model no ss 202 shape round no of pole single type of product open top dustbin size 12*28 inch thickness 0.5 mm pole height 30 inch pipe size 1.5 inch round pipe, 3 mm thickness base plate 5*5 inch plate, 3 mm thickness usage outdoors and indoors...

Due Date : November 13, 2023

Tender Value : ₹ Ref. Documents

View Tender
46
Town Panchayats - Tamil Nadu

40507979 supply for plastic flexy bin and stainless steel dustbin with stand in kuthalam town panchayat , plastic flexi bin raw material high grade hdpe plastic high density poly ethylene capacity 80 ltr bottom dia 370 mm top dia 480 mm height 710 mm weight 1.950 kg thickness 3.5 mm colours blue and green usage / application outdoors and indoors structure open top shape cylindrical type garbage bin , stainless steel dustbin material stainless steel colour silver model no ss 202 shape round no of pole single type of product open top dustbin size 12*28 inch thickness 0.5 mm pole height 30 inch pipe size 1.5 inch round pipe, 3 mm thickness base plate 5*5 inch plate, 3 mm thickness usage outdoors and indoors...

Due Date : November 09, 2023

Tender Value : ₹ Ref. Documents

View Tender
47
Town Panchayats - Tamil Nadu

40507443 supply of dustbin , plastic flexi bin raw material high grade hdpe plastic high density poly ethylene capacity 80 ltr bottom dia 370 mm top dia 480 mm height 710 mm weight 1.950 kg thickness 3.5 mm colours blue and green usage / application outdoors and indoors structure open top shape cylindrical type garbage bin , stainless steel dustbin material stainless steel colour silver model no ss 202 shape round no of pole single type of product open top dustbin size 12*28 inch thickness 0.5 mm pole height 30 inch pipe size 1.5 inch round pipe, 3 mm thickness base plate 5*5 inch plate, 3 mm thickness usage outdoors and indoors...

Due Date : November 14, 2023

Tender Value : ₹ Ref. Documents

View Tender