Southern Railway - Tamil Nadu

33628141 supply and application of single pack pu anti corrosive paint on under frame members in 100 lhb coachessupply and application of single pack pu anti corrosive paint on under frame members in 100 lhb coaches, ...

Chennai Petroleum Corporation Limited - Tamil Nadu

33399551 construction of anganwadi building at tiruvottiyur under corporate environment responsibility (cer) of cpcl construction of anganwadi building at tiruvottiyur under corporate environment responsibility (cer) of cpcl , part a civil works , earth work in excavationinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means (hydraulic excavators)/manually for depth upto 1.5m,including cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, and stacking of excavated material within a lead of 100m, including providing temporary supports to existing facilities viz., service lineslikewater pipes, electric under ground cablesetc. if any all complete as per the specifications and directions of engineer in charge. , same as item no: 20 above, but for depth beyond 1.5m and upto 3.0m. , backfilling after execution of the work to the proper grade and level with selected approved available excavated soil fromsoil heaps within a lead of 100m,including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in foundations, plinths, etc.all complete as per directions of engineer in charge. , transporting & disposing the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the corporation/municipality designated area up to a lead of 7km including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby engineer in charge.( note: if measured by stacks 30%voids will be deducted.) , supplying and filling m sand of specified quality underfootings,pedestal etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layersnot exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of engineer in charge. , supplying and filling approved quarry dust of specified quality under floors, plinths, etc. for all depthsincluding the cost of quarry dust, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors to specified levelall complete as perspecifications and directions of engineer in charge. , providing and laying in position plain cement concrete (pcc) 1:4:8 with 40mm & down size graded aggregate for levelling course/fill under footings,pedestal etc., for all depthsincluding all tools and tackles, labour and material charges, curing, compacting,in any shape, level, thickness, position and finishing the surface smooth/rough etc., complete as directed by engineer in charge. , providing&laying dry rubble soling (hard core) with 20 to 40 mm size metal, under foundations/ ground floor slab (grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of engineer in charge. , providing, mixing and laying in position rcc 1:1.5:3 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m.using 53 grade ordinary portland cement in sub structure for all depths upto ffl level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the cost ofreinforcement and shuttering), etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position rcc1:1.5:3 with 20mm and down graded coarse aggregates as per is 456:2000 with a minimum cement content of 400kg/cu.m. using 53 grade ordinary portland cement in super structure for all heightsabove ffl level including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (excluding the cost of reinforcement, shuttering), etc. all complete as specified,and directed by engineer in charge. , providing and fixing straight / inclinedcentering and shuttering in sub structure for all depths upto ffl levelincluding strutting, bracing, propping etc. keeping the same in position during concreting and de shuttering & removal of the same after specified period as per specifications.keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , providing and fixingstraight / inclined centering and shuttering in super structure at all heights above ffl level including strutting, bracing, propping etc. keeping the same in position during concreting, de shuttering & removal of the same after specified period as per specifications etc.,keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byengineer in charge complete with all tools and tackles,materials, labour charges, consumables etc. (form work shall be supplied by the contractor and shall remain the property of the contractor) , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500 for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge(swg) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry in sub structureup to ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for alldepthsincluding the cost of materials, labour, tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structureabove ffl level using cement mortar 1:5 (1 cement:5 coarse sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying half brick masonry in cement mortar 1 : 4 (1 cement : 4coarse sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing 15mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the engineer in charge. , providing 12mm thick cement plasterin cement mortar 1:4 (1cement:4 fine sand by volume) onbrickmasonry, concrete surfacesincluding preparation of base, cleaning, chipping, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles,material costs etc. as per specifications and asdirected by the engineer in charge. , providing 6mm thick cement plaster in cement mortar 1:3 (1cement:3 fine sand by volume) on roof ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the engineer in charge. , providingandapplying two coats of interior emulsion with wall putty of approved make of any shades/coloursover one coat of primer asper the specifications includingnecessaryscaffolding and surface preparation consisting of application of plaster of paris punning over entire surface, filling all holes and depressions with white cement, applying a coat of primer, two or more coats of oil based putty(as per manufacturers recommendations)sand paperingetc. in walls and roof ceiling, complete as per specification and as directed by engineer in charge. , providing and applyingweather proof textured exterior paint on rcc /brick walls / plastered surface etc. of asian ,nerolac,berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti fungal, water proof, anti flakingweather proof paintof approved quality and shade including painting cartoon characters/kid friendly images in the elevation as per requirement etc.this alsoincludesnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of plaster of paris punning over entire surface,filling all holes and depressions with plaster of paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturers recommendations) sand papering etc., all complete as per specification and as directed by engineer in charge. , supplying, transporting, storing, fabricating & erecting in position bolted and / or weldedstructural steel works like angles, channels, beams, plates, square/round bars, pipes, tubesfor ladders at all heights & levels and locations including all builtup sections/ compound sectionsmade out of rolled sections and / or plates / bent plates for curb edging etc., cutting to required size, straightening/bending if required, edge preparation,cleaning, scrapping & welding, preheating, finishing edges by grinding, fixing in line and level,including preparing the surface for painting,surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease etc complete along with providing paint system as follows:(a) applying inorganic zinc silicate coat 75 micron dft(b) two coats of epoxy primer paint 75 micron dft each(c) two coats of anti rust epoxy top coat paint 100 micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after grit blast cleaning in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , providing and laying of premium quality glazed/matt finish vitrified tiles of size 800x800of kajariaor approved equivalent, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles,4skirting all around as per drawing ,along with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge as per drawing. , providing and laying of premium quality antiskid ceramic tiles of size 300x300 ofapproved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of engineer in charge. , providingand laying coloured glazed ceramic tiles for wall/dado(grade i quality), ofapproved make & shade including 20 mm thick cementbedding c.m. 1:3, pvc beading with matching colour, pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface, all complete with material costs, tools and tackles, stagings labour charges as perspecifications and as directed by engineer in charge. , providing and fixing in position two track two panel sliding upvc windows (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, epdm gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of engineer in charge. , providing and fixing bright finished brass 100mm mortice latch and lock isi marked with four levers and a pair of polished stainless steel decorative handles(size of handles to match the door size) with necessary screws etc. complete (best make of approved quality) as specified by engineer in charge. , providing and fixing solid sheet vinyl wall paper of minimum 150gsm , embossed with textured effect pasted to wall using flake adhesive to be fixed on to the walls/partitions neatly with out shrinkage and bubbles and should have seamless joints. the design , shade and colourshall be as directed by engineer in charge. , providing and fixing isi marked, overall 30mm thickblock board flush door shutters of kutty or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side with decorative1mm thick laminate and another side with water proof laminate of archidply or approved equivalentincluding providing and fixingt type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) including providing wooden filler/sealer, stainless steel lock with status indicator, teak wood lipping, aluminium butt hinges, 3mm thick anodised(anodic coating not less than15 microns) aluminium kicking plate fixed with screws for entire door width on either side of door for a height of 600mm, fixing with door frame,door bush, finishing etc . all complete as directed by engineer in charge. , providing and fixingsecond class teak wooden framesfor doors, windows, ventilators,cupboards etc. for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/rcc by means of 300mm x 25mm x 6mm thick m.s. hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia m.s. dash fastner, painting with two coats of approved shade and make (ici or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by engineer in charge. , supplying and fixing30 mm thick wpc door shutter withframe including towerbolts on either sides,handlesincluding metal hinges and all other fittingsetc. complete as per directions of engineer in charge. , providing & laying to required slope cement concrete screed of mix 1:1.5:3 (1 cement : 1.5 coarse sand: 3 coarse aggregates 12.5mm and down graded aggregates) using 53 grade opc inroof terrace etc. laid to required slope and thickness & inclusive of curing/pond curing, brooming with wire brush, finishingetc.all labours, tools and tackles complete as per drawing, specification & as directed by engineer in charge. , providing and laying water proofing membrane to roof of atactic poly propylene (app) with non woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturers specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. (the thickness of atactic poly propylene (app) membrane to be considered as 4.0mm) , providing and fixing in positionstainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onm.s. brackets, supply, fixing ofm.s.brackets, fasteners, sinkcock (quarter turn range) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipewith heavy bottle trap of parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by engineer in charge. , providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre polished machine cut granite for platformsof approved qualityfor wash basin/ vanity counters,pantry etc.of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 cement:4 m sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. , providing & fixing white floor mounted european water closet (ewc) with dual flush cistern of parry ware petitieor approved equivalent make including cistern, cistern lid, antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook,bibcock andother standard accessories, all fittings and fixturesincluding cutting walls/ floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing & fixing white floor mounted kidseuropean water closet single piece suit (including closet,flushing cistern,soft close seat cover and all fittings)of parryware kids c8941 or approved equivalent make including all fittings,slim line health faucet with hose & hook, bibcock and other standard accessories, all fittings and fixturesincluding cutting walls/ floor, making good of same,making inlet/outlet connection, finishing, etc.all complete as per the directions ofengineer in charge. , providing and fixing white glazed earthenware china kids wash basin with pedestal of make parryware make c8943 or approved equivalent of 530x290x520 mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing and fixing white glazed earthenware china wash basin of make parryware/hindware with antisplash rims on 3 sides of 550x450mm sizeincluding approved cast iron/ms brackets , one 15mm dia. cp brass pillar cock, rubber plug with cp brass, 32mm cp waste fitting of standard pattern pipe with 32mm dia. pvc pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by engineer in charge. , providing and fixingmirror of superior glass of parryware or approved equivalent complete with cp brass screws, fastners and washers complete as directed by engineer in charge. , providing and fixing600 mm long cp rodtowel rail of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by engineer in charge. , providing and fixing c.p. brass shower rose 100mm diameter with 15 to 20mm inlet of parryware or equivalent approved including 230mm shower arm, making inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing of cp brass twin robe hook of parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with cp screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by engineer in charge. , providing and fixing15 mm nominal outer dia. & sdr11 chlorinated poly vinyl chloride(cpvc) pipes (exposed on wall) , of approved equivalent make having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. this includes jointing of pipes & fittings with one step cpvc solvent and testing of joints complete as per directions of engineer in charge. , same as sl. no: 450 above, but for 20mm nominal outer dia. pipes , same as sl. no: 450 above, but for 50mm nominal outer dia. pipes , providing and fixing 80mm dia. nominal boreunplasticised rigidpvc(upvc pipe) sch. 40 water line pipes (concealed pipeline) conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion (single socketed pipes) with necessary fittings /accessories etc.all complete as per specifications and as directed by engineer in charge. , same as sl. no. 480 above, but for 100mm dia. nominal bore pipes. , same as sl. no. 480 above, but for 150mm dia. nominal bore pipes. , providing and fixing 150 mm dia. rigid pvc rain water pipeswith ms holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing100 mm dia.rigidpvc pipes with pressure rating of 4 kg/ sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring jointsusing approved lubricant, making hole in the slaband restoring the same to the original condition including provision of cowl in the septic tank vent pipe etc. complete as per specifications and directions of engineer in charge. , providing and fixing two way bibcock single lever range with flange of parryware or equivalent approved 15mm nominal bore cp including fixingand connections, etc. completeas directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal bore brass bibcock including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal borebrass angle valve including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by engineer in charge. , providing and fixing 50 mm nominal bore gun metal gate valve (lever type) lever of approved quality including all fittings etc. complete as directed by engineer in charge. , supplying and laying custom (prefabricated) pvc floor sumps/ floor traps fabricated out of 110mm dia. 6 kg/cm2 class pvc pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix cp/pvc colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by engineer in charge. , providing, hoisting and fixing in position rcc precast elementswithreinforced cement concrete grade 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate(20mm & down size) withopc 53 grade cementfor shelves in kitchen and store room, storm water drain and septic tank cover slabs for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position, all complete (excluding cost of reinforcement) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supply and installation of cylindrical triple layer white virgin plastic storage tank of capacity 1000 litres of sintex or approved equivalent onground floor roof with lid and making necessary cutout /holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly,all complete. including, fixing, transportation to work site all complete as per drawings and directions of engineer in charge. , demolishingthe existing building in the location approx.120sq.m (taking all necessary safety precautions) for allheights and depths above plinth level including dismantling of flooring, fixtures, doors, windows, brickwork,columns,truss,purlin, structural steel items etc. all complete as directed by engineer in charge. this includes demolishing foundation including raft and underlying layers.all unserviceable material should be disposed atcorporation/municipality designated area upto a lead of 7kmas directed by the engineer in charge. all serviceable materials shall be the property of contractor. , supply of unskilled labourto carry out petty works not assessable for measurements/minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools etc. all complete as directed by engineer in charge. , supply of jcb on hire basis on all days including sundays on 8 hrs.shift including driver,assistant /fuel/oil/lubricants /all consumables etc. complete. the quoted rate should include mobilization, operator crews/driver /assistant cost,tools, tackles etc., as directed by the engineer in charge. , part b electrical works , supply and laying of pvc wires: the scope of work includes supply of following size of pvc insulated, copper conductor and laying in the existing surface / recessed, pvc / steel conduit / pvc casing and capping as required including connection in fans, switches, light fitting, sockets etc, as per the specifications of this tender and directions of engineer in charge. note: only isi marked cables shall be used. , 1.5 sq.mm , 2.5 sq.mm , 4 sq.mm , 6 sq.mm , supply and laying of pvc conduits: the scope of work includes supply and laying of following size of pvc conduit along with the accessories to be used for installation in surface/concealed as required, as per the specifications of this tender and directions of engineer in charge. note: only isi marked conduits shall be used. , upto 25 mm , earth pit: the scope of work includes supply , installation , testing and commissioning ofearth pitwith 65 mm dia 3000 mm longearth electrodes , complete wih all necessarymaterialsincludingexcavation of earth pit , fillingwith charcoaland salt, back filling , providing cement (concrete) slab for earth pits, paintingand markingof earth pit nosand connectionsincluding all labour and materialsand as per the specifications of this tender and directions of engineer in charge , earth flat / wire: the scope of work includes supply, installation and connection of following gi earthing strips along the cable trenches or cable trays or fixing to walls or structures and for connecting equipments to the plant grid including welding at joints, providing anti corrosive paint or bitumen and jute covering for welded portion, clamping and necessary hardware for connection etc., including all labour and materials, as per approved drawings, specification of this tender and direction of engineer in charge. , 40 x 6 gi earth flat , 8 swg wire for earthing , supply and installation ofswitch & sockets: the scope of work includes supply of the below mentioned switch & sockets as per the specifications of this tender and directions of engineer in charge. , supply and installation of 5/6 amps socket outlet , supply and installation of 5/6 amps switch , supply and installation of 16 amps socket with switch , wall mounted bulb holder with led lamp:the scope of work includes supply and fixing of wall mounted bulb holder along with min 15 w led lamp and other related accessories as per the directions of engineer in charge , tube light fitting: the scope of work includes supply and fixing of led l.fixt elite pride plus 18 w 6500 k1, cool daylight (cdl), decorative slim linear 4’ led batten fittings with bulb of havells catalogue or equivalent ,including civil work (if any) required for installation, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , supply and fixing of module box:supply and fixing of plastic/metal boxes of following sizes with all accessories including necesssary base frame plates/ mounting , cover plates, etc.,suitable for fixing decorative switches of type roma or equivalent make in havells/siemens/anchor/l&t , 1 or 2 module box , 4 module box , 6 module box , 8 module box , 12 module box , ceiling fan: the scope of work includes supply, installation, testing and commissioning of 1200mm sweep ceiling fan ofbajaj / crompton greaves / khaitan / usha / havells make of following sweep withceiling fan and regulator, including wiring the down rod of standard length (upto 30 cm) with 1.5 sqmm, pvc insulated, copper conductor, single core cable etc., as required,, as per the specifications of this tender and directions of engineer in charge. , supply and installation of 12 way db:the scope of work includes supplyand installation of 12 way db with 40 a mcb, 40 a rccb and 8 nos of 10 a mcb as per the specification of this tender and directions of engineer in charge. this shall be inclusive of all mcb and rccb => limited...

Southern Railway - Tamil Nadu

33252845 supply of anti corrosive paintanti corrosive paint,anti corrosive paint for railway coaches as per specification icf/md/spec 357 issue status:01 rev:00 dated:30/03/2019....

municipality - Tamil Nadu

33223641 additional facility to vadasery christopher busstand sl. no. item description 1 additional facility to vadasery christopher busstand 2 dismantling the plain cement concretecleaning away and carefully stocking materials usefull for reuse 3 dismantling the rein forced cement concrete cleaning away and carefully stocking materials usefull for reuse 4 dismantling the brick masonryincementmortorcleaning away at carefully stocking materials usefull for reuse for any thickness at well 5 removing exisiting door and windows including reused and frame, hinges etc 6 removing the damaged asbestos cement sheet without roof timbers 7 refilling the basement with excavated earth in layers of not more than 15 cm thick well rammed watered and consolidated etc. complete with standard specification. 8 earth work excavation for foundation in all types of soils and sub soils to full depth (such as soils in rock / silt / light black cotton soil / ordinary soil ) except in rock requiring blasting but inclusive of shoring, shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth other than sand in layers of 150 mm thick well rammed and consolidated, depositing the surplus earth in places shown by the departmental officers with initial lead of 10 m and initial lift of 2 m. complete as per tnss23 & 24, v, vi (s2), vii, 9,10a )coloumn depth of 3m 5m 9 boring, providing and installing bored castin situ reinforcement cement concrete pile of specified diameter and length below the pile cap in cement concrete 1:1.5:3 (1 cement, 1.5 coarse sand, & 3 graded stone aggregate of 20 nominal size) to carry a safe working load not less than specified excluding the cost of steel reinforcement but including bentonite solution mechinery & labour charges etc, all complete. (length of pile for payment shall be measured from bottom of pile to the bottom of pile cap). length of payment shall be measured from bottom pile to the bottom of pile cap 10 supply delivery and filling of river sand in layer of not more than 15cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyance of sand at site and all labour charges and all other incidential charges etc., complete as per standard specification tnss no. 24 & 25. 11 cement concrete of mix 1 : 4 : 8 (one cement four sand eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. 12 supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing,coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification( tnss no or nbc no 30(s) 86 86 a v, vi(s3)vii .a)column mat, grade beam & drainage 13 supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing,coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification( tnss no or nbc no 30(s) 86 86 a v, vi(s3)vii. b)coloumn 14 supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing,coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification( tnss no or nbc no 30(s) 86 86 a v, vi(s3)vii. c) circular coloumn 15 supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing,coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification( tnss no or nbc no 30(s) 86 86 a v, vi(s3)vii. d) slab & beam 16 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg/ cum and maximum water cement ratio of 0.55 including admixture (plasticiser / super plasticiser) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is staandards. (no separate payment will be made by the department for the excess usage of materials) a) upto basement 17 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg/ cum and maximum water cement ratio of 0.55 including admixture (plasticiser / super plasticiser) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is staandards. (no separate payment will be made by the department for the excess usage of materials) b) ground floor 18 providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg/ cum and maximum water cement ratio of 0.55 including admixture (plasticiser / super plasticiser) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is staandards. (no separate payment will be made by the department for the excess usage of materials) c) first floor 19 supplying and fabrication of steel and placing in position ms / ribbed tor steel grills for rcc works as per design given including cost of steel and gi binding wire in floors etc., complete complying with standard specification in force per kilogram. 20 brick work in cm 1:5 (one cement & five sand) using iii class ground moulded bricks of size 8 3/4x4 1/4 x 2 3/4 including finishing, curing, etc., complete complying with standard specification 100cft upto basement 21 brick work in cm 1:5 (one cement & five sand) using iii class ground moulded bricks of size 8 3/4x4 1/4 x 2 3/4 including finishing, curing, etc., complete complying with standard specification 100cft upto ground floor 22 brick work in cm 1:5 (one cement & five sand) using iii class ground moulded bricks of size 8 3/4x4 1/4 x 2 3/4 including finishing, curing, etc., complete complying with standard specification 100cft upto first floor 23 brick partition walls using iii class ground moulded chamber bricks of size8 3/4x4 1/4 x 2 3/4 in c.m 1:3using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification 10 sqm 24 specialplasteringinc.m. 1 : 3 ( one cement, three sand) to10 mmthickincludingallcostandconveyance ofallmaterialstositeincludingcostofcementwhichwillbepurcharedlocallybythe contractor andconveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 25 plasteringinc.m. 1 : 4 (1cement 4sand)to12 mmthickincludingallcostandconveyanceofallmaterials tositeincludingcostofcementwhichwillbepurcharedlocallybythecontractor and conveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 26 cement concrete of mix 1 : 2 : 4 (one cement two sand four aggregates) using 20mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. 27 weatheringcoarsewith concrete broken brick jelly concrete on 20mm. gauge in pure slaked shell lime (no sand to be used) over roof slab be proportion of brick jelly to being 32cft 12.5 cft. well beaten with wooden beaters giving the required shape and thickness as directed by the departmental officers. 28 finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 (one cement add three sand) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete 29 supply and fixing of m.s grills for windows,with one coat of red oxideprimer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. including phosphating as per isi with rust preventive primer & ready to assemble condition for easy installation at site including dismantlingmaking necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. and steel doorcomplete as directed by the departmental officer. 30 supplying and erecting pull and push type rolling shutter with i.s.i. make of approved size and section using 18 gauge g.i.sheet with manually operated type. the shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc, complete as per standard specification. 31 supplying and laying of stainlesssteel hand rails fabricated with 50mm dia 40mm dia and 20mm dia stailess steel pipe used in ramp sideof hand rails and four of stainless steel pipe are welded harijontally at the middile of the hand rails made 18mm s.s. pipe & elegant stainless steel balls are provided in required places of hand rail as directed by the departmental officers. the size including cost of material welding with stainless steel grinding and good polishingand fixed in the hand rails with good position as directed by the departmental officers 32 plain cement concrete 1:8:16 (one cement eight fine aggregates and sixteen coarse aggregates) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification 33 dadooing sides of walls with glazed design tiles of size 305 x 200 x 6mm set in cement mortar 1:3 ( one cement, three sand) 20mm thick and pointed with the same colour cement including cost and conveyance of all materials, labour charges complete as per standard specification. 34 floor finishing first quality design ceramic tiles of all colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete 35 supply and fixing of granite slabs (super fine polished with machine cut edges) of sizes4x2 and above 18mm to 20mm thick. laid over a base layer of cement mortar 1:3mix 20mm thick and pointed with white cement and pigment of suit the colour of stones and polished neatly as directed by departmental officers. 36 plain cement concrete of mix 1 : 3 : 6(one part of cement threepart of sand six part of aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. tndss no: 28 v, vi (s2) v,vi (s5a) vii 37 supplying and laying in flooringwith fully polished sinthetic grey colour granite stone of 20mm thick (average) of 4 x 2 in size laid over base layer of cementmortar 1:3 (one cement and three sand) 20 mm thick and applying cement slurry &pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers 38 supplying and painting thewalls with twocoatsweather sealedexterior emulsion paint as instructed by the departmrntal officers includingpreparation of surface curing, etc complete in all floorscomplying with standard specification. ( the colour and shade of the paint shall be got approved by the departmental officers.) 39 painting the new iron works such as steel doors, windows,ventilators windows bars,balustrades etc,in all floor withtwo coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc,complete complying with standard specification. ( the make, quality and colour of paint should be got approved bythe engineer in charge before use on works )( tnss no or nbc no 61 v vi (54) 3) 40 supply and fixing of pvc soliddoors with necessay accessories and locking arrangements including cost and conveyance of all materials and labour charges etc., complete as per standard specification 41 supplyingand fixing of rcc precast slab withcementconcrete 1:2 : 4mix using 20 mm metal for 200mm thick includingall costandconveyance of all materials and all labour and materials chargesetc complete as per standard specification 42 supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (the wash hand basin and specials should be got approved by the executive engineer before use on works). 43 supplying and fixing in position white glazed indian water closet of size 580 x 440mm of orissa type of approved quality with p or s trap with sand cushion and forming flooring alround the closet using 40mm broken brick jellylime concrete 1:2:5 ; 100mm thick and finishing the top torequired slope and including giving necessary connection to cast iron soil pipes by dismandling masonry / rcc works and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmentalofficers. (the water closet should be got approved by the executive engineer before use on works.) 44 supplying and fixing in position urinal of approved quality andmake with p os s trap with double flapped rigid p.v.c. seat cover with c.p. brass hinges,12.5 litres pvclow level flushing tank with all internal fittings etc., complete complying with standard spoecifications 45 supplying and fixing in position white glazed european water closet of approved quality andmake with p os s trap with double flapped rigid p.v.c. seat cover with c.p. brass hinges,12.5 litres pvclow level flushing tank with all internal fittings etc., complete complying with standard spoecifications 46 supply and laying of 2 x 10 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. 47 supply and laying of 4 x 16 sq.mm pvc armoured ltug cable in a trench to the excavated at a depth of 0.75 metre putting 0.15 mt. layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. 48 supply and fixing of brass cable gland for 4 x 16 sq.mm pvc armoured ltug cable, with earth connection. 49 supply and laying of 31/2 x 25 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 metre putting 0.15mt. layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. 50 supply and fixing of brass cable gland for 31/2 x 25 sq.mm ltug armored cable with earth connection. 51 supply and run of 25mm x 3mm tinned copper flat necessary clamps / supports on wall / floor / ground floor earth connection. 52 earthing as per the isi specification with an earth electrode of 2.1mt class b gi pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry. 53 wiring with 2 x 1.5 sqmm (22 /0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3mm thick hylum sheet cover with tw switch box and 5a f.t. switch with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point (for electronic regulator). etc, complete as per standard specifications. 54 wiring with 2 x 1.5 sqmm (22 /0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 150 x 100 x 113 mm tw switch box with 3mm hylum sheet cover for5a 3 pin non inter locking cs plug with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed pvc plug point.etc, complete as per standard specifications 55 wiring with 2 x 4 sqmm (56 / 0.3mm ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable heavy gauge pvc pipe on wall and ceiling with pvc accessories inflush with wall with 150mm x100mm x75mm ms switch box concealed type with 3mm thick hylum sheet cover for 15a 3pin flush type non inter locking cs plug with continuous earthwire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed power plug point.etc, complete as per standard specifications. 56 supply andfixing of 16 amps dp switch with metal glad of 500v with fuse and nuetral ( side handle) on suitable tw box pwd earthing 57 supply andfixing of 16 ampsfuse unit and neutral ( side handle) on suitable tw box pwd earthing 58 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit (500v) 32a neutral link and earth link (1 x 1/8 copper flat) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7/20 pvc insulated copper wire from eb meter to fuse unit 59 supplying laying and jointing pvc pipes of approved quality and best varity of b class pipe of the following sizes including fixing g.i specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. the pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red oxide primer etc., complete.a)110mm dia pvc pipe 4 kg/cm2 60 supplying laying and jointing pvc pipes of approved quality and best varity of b class pipe of the following sizes including fixing g.i specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. the pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red oxide primer etc., complete.b)75mm dia pvc pipe 4 kg/cm2 61 supplying laying and jointing pvc pipes of approved quality and best varity of b class pipe of the following sizes including fixing g.i specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. the pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red oxide primer etc., complete.c)32mm dia pvc pipe 10 kg/cm2 62 supplying laying and jointing pvc pipes of approved quality and best varity of b class pipe of the following sizes including fixing g.i specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. the pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red oxide primer etc., complete.c)25mm dia pvc pipe 10 kg/cm2 63 supplyingandfixingin position best approvedof bis quality 110mm p.v.c rainwaterdownfallpipe having a pressure of 4kg / sq.cm including cost of necessary pvc shoe,pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc, and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc, complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of uclamp at the centre of the pipe line in addition to those for more than 3.00mt pipe length etc,completecomplyingwithstandardspecifications. 64 supplying and fixing in position first quality and approved variety of 32mm gun metal gate valve (heavy type) with i.s.i.mark of the following sizes including cost of shellac , thread etc,.including labour for cutting and threading of g.i.pipes etc.,complete complying with standard specifications for both internal and external water supply arrangements. 65 supplying and fixing in position p.v.c. specials such as plain bend, door bend, plain tee, door tee, offsets,y junction, plain or with door of various sizes best quality confirming to i.s.s and providing leakproof joints including fixing to wall and giving connection to the p.v.c, soil stacks, dismadling the brick masonry or r.c.c.floor or roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.a)110mm dai pvc elbow(mould) 66 supplying and delivery of following pvc pipe and specials with isi mark including cost and convience of materials etc completed.. a)75mm dia pvc elbow 4kg 67 75mm dia door elbow 68 75mm dia 45 pvc elbow 69 110mm dia pvc door elbow 70 110mm dia pvc 45 elbow 71 32mm dia pvc elbow 72 25mm dia pvc elbow 73 32mm dia pvc tee 74 25mm dia pvc tee 75 32mmx25mm dia pvc tee 76 25mmx20mm dia pvc tee 77 32 x 25mm pvc reducer 78 supplying and fixing of 2000 liters capacity hdpe tank with is specification is 10701/96 the tank is meant for outdoor (or)indoor use complete with removable hinged top locking arrangement and to make provision to fix water supply pipe lines, necessary man hole with cover and including all pvc specials pugs, screws nails to fix the tank etc., complete and the tank should fixedfirming as directed by the departmental officers.the rate shall be inclusive of all materials, labour conveyance hoisting and fixing charges etc. (the water tank should be got approved by the eebefore use on work. 79 supply and fixing of ci nahini / floor trap with stainless steel gratings 100 mm x 75 mm including all charges etc, complete as per standard specification. ...

Chennai Petroleum Corporation Limited - Tamil Nadu

33207938 zonal contract 2022 23 for projects related electrical works in manali refinery of cpcl zonal contract 2022 23 for projects related electrical works in manali refinery of cpcl , ht cable laying in trenches: the scope of work includeslaying of armoured / unarmoured pilca / pvc insulated and pvc sheathed / xlpe ht power cables of voltage grade exceeding 1.1 kv but not exceeding 11 kv ( e ) of following sizes in pre excavated cable trench or existing trench / rcc or hume or stoneware or metal pipe / masonry duct, fixing of cable number tag at specified interval and both ends, testing plus transportation from stores to site , unpacking, straightening, dressing of cable, required clamping, cable route markering at a frequent interval and returning the empty drum / cable drum with unused cable, if any, to stores / scrap yard or any other place within cpcl , all complete with labour as per the drawings, specifications of the tender and directions of the engineer in charge. note: necessary crane or forklift, tractor and trailershall be arranged by the contractor. the scope also includes area cleaning and vegetation removal as a enabling activity for cable laying. the scope excludes supply of cables. , single core, upto 630 sq.mm , from 3c x 120 sq.mm to 3c x 185 sq.mm , from 3c x 185 sq.mm to 3c x 300 sq.mm , ht cable laying on trays / structures: the scope of work includes horizontal and vertical laying of armoured / unarmoured pilca / pvc insulated and pvc sheathed / xlpe ht power cables of voltage grade exceeding 1.1 kv but not exceeding 11 kv ( e ) of following sizes on cable racks / wall and steel structures upto any height, fixing of saddles, aluminium strip, number tags ( if required ) , testing plus transportation from stores to site, unpacking, straightening, dressing of cable, fixing with clams / cleats as required and returning the empty drum / cable drum with unused cable, if any, to stores / scrap yard or any other place within cpcl , all complete with labour as per the drawings, specifications of the tender and directions of the engineer in charge. note: necessary crane or forklift, tractor and trailershall be arranged by the contractor.the scope also includes area cleaning and vegetation removal as a enabling activity for cable laying. the scope excludes supply of cables. , single core, upto 630 sq.mm , from 3c x 120 sq.mm to 3c x 185 sq.mm , from 3c x 185 sq.mm to 3c x 300 sq.mm , laying of lt power / control / telephone / plant communication and other cables in trenches: the scope of work includes horizontal and vertical laying of one or more armoured / unarmoured pijf / pvc insulated and pvc sheathed / xlpe lt power ( voltage grade upto1.1 kv ) / multi pair or multicore control cables / telephone and other cables of following sizes in pre excavated cable trench or existing trench / rcc or hume or stoneware or metal pipe / masonry duct, fixing of cable number tag at specified interval and both ends, testing plus transportation from stores to site, unpacking, straightening, dressing of cable, required clamping, and returning the empty drum / cable drum with unused cable, if any, to stores / scrap yard or any other place within cpcl , all complete with labour as per the drawings, specifications of this tender and directions of the engineer in charge. for 2c, 3c, 4c cables below rates of 3.5c cables will be applicable. note: necessary crane or forklift, tractor and trailershall be arranged by the contractor. the scope also includes area cleaning and vegetation removal as a enabling activity for cable laying. the scope excludes supply of cables. , all controlcables and power cables upto 3.5 c x 25 sq.mm , power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core cable above 500 sq.mm upto 1000 sq.mm , laying of lt power / control / telephone / plant communication and other cables on cable trays / structures: the scope of work includes horizontal and vertical laying of one or more armoured / unarmoured pijf / pvc insulated and pvc sheathed / xlpe lt power ( voltage grade upto1.1 kv ) / control / telephone and other cables of following sizeson cable racks / wall and steel structures upto any height, fixing of saddles, aluminium strip, fixing of cable number tag at specified interval and both ends, testing plus transportation from stores to site, unpacking, straightening, dressing of cable, fixing with clams / cleats as required and returning the empty drum / cable drumwith unused cable, if any, to stores / scrap yard or any other place within cpcl etc. all complete with labour as per the drawings, specifications of this tender and directions of the engineer in charge. for 2c, 3c, 4c cables below rates of 3.5c cables will be applicable. note: necessary crane or forklift, tractor and trailershall be arranged by the contractor. the scope also includes area cleaning and vegetation removal as a enabling activity for cable laying. the scope excludes supply of cables. , all controlcables and power cables upto 3.5 c x 25 sq.mm , power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core cable upto 1000 sq.mm , temporary cable laying : the scope of work includes temporary layingof ht / lt power / control / telephone cables on any surface as required including shifting, handling, testing, cutting, sealing, etc., transporation of cable from stores to site and returning the empty drum / cable drum with unused cable, if any, to stores / scrap yard or any other place within cpcl , all complete with labour and materials as per the drawing, specification of this tender and direction of the engineer in charge.for 2c, 3c, 4c cables below rates of 3.5c cables will be applicable. note: necessary crane or forklift, tractor and trailershall be arranged by the contractor. the scope also includes area cleaning and vegetation removal as a enabling activity for cable laying. the scope excludes supply of cables. , all lv control cables and lv power cables upto 3.5c x25 sq.mm , lv power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , lv power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , lv power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core lv power cable upto 1000 sq.mm , single core ht cable upto 630 sq.mm , ht cables from 3c x 120 sq.mm upto 3c x 185 sq.mm , ht cables from 3c x 240 sq.mm upto 3c x 300 sq.mm , cat 6 cabling: the scope of work includes supply and laying of cat 6 type in already available pvc pipe / casing caping with all necessary accessories for computer networking. only isi marked wires of make finolex / polycab / havells / kei / rpg / v guard shall be used. , straight through jointing kit , ht cable jointing kits: the scope of work includes supply of heat shrinkable straight through jointing kitsand making straight through joints for xlpe insulated ht power cables 6.6kv / 11kv ( ue ) grade of following sizeswith copper / aluminium ferrules including all labour, tools and materials, as per the direction of engineer in charge. , 1c upto 630 sqmm , 3c upto 300 sqmm , lt cable jointing kits: the scope of work includes supply ofstraight through jointing kitsand making straight through joints for pvc insulated ltpower cables, control cables of 1100v grade of following sizeswith copper / aluminium ferrules including all labour, tools and materials, as per the direction of engineer in charge. for 2c, 3c, 4c cables below rates of 3.5c cables will be applicable. , all control cables / lv power cables upto 3.5c x 25 sq.mm , lv power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , lv power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , lv power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core lv power cable upto 1000 sq.mm , glanding & end termination , ht end termination kits: the scope of work includes supply of heat shrinkable end termination kits and making end terminations for xlpe / pvc insulated ht power cables of 6.6kv / 11kv ( ue ) grade of following sizes including supply of copper / aluminium lugs, crimping / soldering as necessary, earthing of armour, connecting to equipment terminal, including cutting, stripping and glandingwith all labour, tools and materials and as per the direction of engineer in charge. note: the scope excludes supply of glands. , 1c upto 630 sq.mm , 3c upto 300 sqmm , lt cable end termination: the scope of work includes glanding and making end terminations for xlpe / pvc insulated lt power cables of 1100 v grade of following sizes including supply of copper / aluminium lugs, bimetallic strip, crimping paste, crimping / soldering as necessary, earthing of armour, connecting to equipment terminal, including cutting stripping and glandingwith all labour, tools and materials and as per the direction of engineer in charge. for 2c, 3c, 4c cables below rates will be applicable. note: the scope excludes supply of glands. , all lv control cables and lv power cables upto 3.5c x 25 sq.mm , lv power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , lv power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , lv power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core lv power cable upto 1000 sq.mm , communication cable end termination: the scope of work includes end terminations oftelephone / plant communicationcables of 1100 v gradeof following sizes including supply oflugs, crimping / soldering as necessary, connections in crone terminal / any terminals, including cutting , stripping and glanding, all complete with labour, tools and material, as per specifications of this tender and directions of engineer in charge. the scope excludes the supply of cable glands. , 100 paircommunication cable , 20 pair to 50 pair communication cable , upto 10 pair communication cable , gi pipes: the scope of work includes supply and laying of gi pipes of following sizes of class ‘b’ type, fixed on steel, duct bank, concrete, wall crossing, wing trenches or similar structures, including shifting of pipes to site using contractors vehicle, cutting, bending, threading, supply & installation of supports, clamps, small iron structures, spacer, seats, plugs, bush and fittings / fixtures like bends, tees, nipples, reducers etc., all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. the scope of work also includes sealing of pipe ends and joints with bushes and bitumen based fillings and other miscellaneous works to make the piping water tight. , 150 mm od gi pipe , 100 mm od gi pipe , 50 mm od gi pipe , miscellaneous electrical works , supply of extension board: the scope of work includes supply of 4 way extension board ofhavells ahlklup104 maglev or equivalent model, as per the specifications of this tender and directions of engineer in charge. , decorative luminaire: the scope of work includes supply and fixing of ( 2’ x 2’ ) decorative led luminaire of philips make rc380b g3, minimum 34w, 6500k fiting or equivalent in philips / cg / ge / havells, including consumables required for suspension / clamp arrangement, civil work ( if any ) required for installation, all complete with labour , tools and materials, as per the specifications of this tender and directions of engineer in charge. , led downlights: the scope of work includes supply & fixing of recess mounted, compact vertical, round shapedupto 10w led 6000k downlighter with removable driver of havells make or equivalentsuitable for low ceiling heights, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , tube light fitting: the scope of work includes supply and fixing of led decorative slim linear 4 ft batten fittings with bulb min.18 w 6500 k1, cool daylight ( cdl ) , of havells catalogue or equivalent , including civil work ( if any ) required for installation, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , twin led tube light fitting: the scope of work includes supply and fixing ofmin. 2 x 18 watts 4 ft industrial tube light fittings with bulb of havells catalogue titania sleek t8 led tubelight or equivalent, including civil work ( if any ) required for installation, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , socket outlet: the scope of work includes supply and fixing of 20 amps, 240 volts, spn industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps, g series, single pole mcb in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, including connections, testing and commissioning etc. as required, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. note:isi marked sockets of approved make shall be used. , 3 phase 6 way distribution board: the scope of work includes supply, erection, connecting, testing and commissioning of 3 phase 6 way distribution board concealed in wall / partition. the board shall be powder coated with below mentioned provisions and necessary accessories for db, all complete with labour , tools and materials, as per the specifications of this tender and directions of engineer in charge. note:isi marked components of approved make shall be used. , with incoming 63a four pole mcb, 63a 30ma elcb and out going 18 nos. of 6 / 10 amps mcbs , 4 way flp / wp junction box: the scope of work includes supply of 4 way junction box of below mentioned type, as per the specifications of this tender and directions of engineer in charge. note:isi marked components of approved make shall be used. , flameproof jb , weather proof jb , supply of mcb: the scope of work includes supply of following rating, 240 / 415 volts, 50hz, 10kaminiature circuit breaker ( suitable for motor, lighting and other inductive loads and conforming to is 8828: 1996, iec 60898: 2002 ) of following poles in the existing mcb db with required rails / fastenersfor fixing as per the specifications of this tender and directions of engineer in charge. note: isi marked mcbs as per approved vendor list attached with the tender shall be used. , upto 32a, single pole , upto 32a, double pole , upto 63a, 4p / tpn , installation of mcb:the scope of work includes fixing of mcbupto 63 a, 4p with required rails / fastenersincluding connections, testing and commissioning etc, all complete with labour and tools, as per the specification of this tender and directions of engineer in charge , supply of rccb: the scope of work includes supply offollowing rating 240 / 415 volts, residual current circuit breaker ( rccb ) , isi marked, having a sensitivity current indicated miliamperes in the existing mcb db with required rails / fastenersfor fixing, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. note: isi marked rccb shall be used. , upto 32 a, 30 ma, 2p , 63 amps., 30 ma, 4p , installation of rccb:the scope of work includes fixing of rccb of rating upto 63 a, 4p with required rails / fastenersincluding connections, testing and commissioning etc, all complete with labour and tools, as per the specification of this tender and directions of engineer in charge , supply of mpcb: the scope of work includes supply offollowing rating ofmotor protection circuit breaker ( mpcb ) , isi marked with required rails / fastenersfor fixing, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , upto 6.3 a , above 6.3 a upto 13 a , above 13 a upto 25 a , above 25 a upto 32 a , installation of mpcb:the scope of work includes fixing of mpcb of following rating with required rails / fastenersincluding connections, testing and commissioning etc, all complete with labour and tools, as per the specification of this tender and directions of engineer in charge. , supply of pvc wires: the scope of work includes supply of following size of pvc insulated, copper conductor for laying in the existing surface / recessed, pvc / steel conduit / pvc casing and capping as required, as per the specifications of this tender and directions of engineer in charge. note: only isi marked cables shall be used. , 1.5 sq.mm , 2.5 sq.mm , 4 sq.mm , 6 sq.mm , supply of pvc conduits: the scope of work includes supply of following size of pvc conduit along with the accessories to be used for installation in surface / concealed as required, as per the specifications of this tender and directions of engineer in charge. note: only isi marked conduits shall be used. , upto 25 mm , above 25 mm upto 40 mm , above 40 mm , laying of pvc conduit: the scope of work includes fixing of following size of pvc conduit along with the accessories to be used for installation in surface / concealed as required, including cutting the wall and making good the same in case of recessed, as per the specifications of this tender and directions of engineer in charge. , upto 40 mm , more than 40 mm , supply of pvc casing / caping: the scope of work includes supply of following size of pvc casing and capingon surface as required, as per the specifications of this tender and directionsof engineer in charge. , 20 mm x 10 mm , 25 mm x 10 mm , 40 mm x 20 mm , laying of pvc casing / caping: the scope of work includes fixing of following size of pvc casing and capingon surface as required, as per the specifications of this tender and directions of engineer in charge. , upto 40 mm x 20 mm , laying of pvc wires: the scope of work includes drawing / laying of following size of pvc insulated, copper conductor for laying in the existing surface / recessed, pvc / steel conduit / pvc casing and capping as required, as per the specifications of this tender and directions of engineer in charge. , 1 x 1.5 sq.mm , 2 x 1.5 sq.mm , 3 x 1.5 sq.mm , 1 x 2.5 sq.mm , 2 x 2.5 sq.mm , 3 x 2.5 sq.mm , 2 x 4 sq.mmto 2 x 6 sq.mm , switch socket / outlet: the scope of work includes supply, fixing and connection of 250 vflush type anchor make or approved equivalent switch, socket bell push etc. on perpex sheet on ms box including supply and fixing of nuts, bolts, cutting etc. but excluding the perpex sheet, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , 1 way 5 / 6 amps. penta flush type switch with isi mark , 1 way 15 / 20 amps penta flush type switch with isi mark , 5 pins 5 / 6 amps. penta flush type socketwith isi mark , 6 pins 10 / 20 amps.socket outlet with isi mark , 3 pins 5 / 6 amps. isi marked polycarbonate unbreakable plug top , 3 pins 15 / 16 amps. isi marked polycarbonate unbreakable plug top , telephone jack , 10 / 20 amps 5 pins switch socket combinedisi marked , supply and fixing of module box:supply and fixing of plastic / metal boxes of following sizes with all accessories including necesssary base frame plates / mounting plates, etc., suitable for fixing decorative switches of type roma or equivalent make in havells / siemens / anchor / l&t , 1 or 2 module box , 3 module box , 4 module box , 6 module box , 8 module box , 12 module box , supply, fixing and connection of modular type of anchor make ( roma ) or approved equivalent switch, socket bell push etc in havells / siemens / anchor / l&t / equivalent, complete with labour, tools andmaterials as per direction of the engineer in charge. , 10 a, 1way switch , 20a, 1 way switch , 3 pins 5 / 6 amps socket with isi mark , 3 pins 10 / 20a, heavy duty uni socket outlet with isi mark , 3 pins 5 / 6 amps. isi marked polycarbonate unbreakable plug top , 3 pins 15 / 16 amps. isi marked polycarbonate unbreakable plug top , rj11 telephone jack single with shutter along with base module box , single module dimmer / fan regulator 450w , rj 45 computer socket cat 6 with shutter & box , elmex terminals: the scope of work includes supply & installation of elmex type terminals, wherever required. the scope of work also includes drilling holes, providing and fixing clamps / din rail, nuts and bolts etc. suitable for terminating copper conductor of below mentioned size as per drawings and specifications of this tender and directions of engineer in charge. ( per terminal ) . , elmex connectors of 2.5 / 4 sq.mm , elmex connectors of 6 / 10 sq.mm , elmex cbt 110 connectors from 16 sq.mm upto 50 sqmm ( with bars ) , din rail channels: the scope of work includes supply and fixing of din rail channels for installation of elmextype terminals wherever required. the scope of work also includes drilling holes, providing and fixing clamps, nuts and bolts etc., as per the drawings and specifications of this tender and directions of engineer in charge. , telephone system , 2 pair telephone cable: the scope of work includes supply and laying of 2 pair telephone cablefrom the epabx system / telephone jb to officer’s table, all complete with labour, tools and materials, as per the specifications of this tender and directions of engineer in charge. , 100p telephone junction box: the scope of work includes supply and installation of 100 pair telephone junction box with crone connector with cable entry provision for1 number of 100 pair cable for incomingand 1 number of 50 pair cable, 2 numbers of 20 pair cable , 1 number of10 pair cable for out going, all complete with labour, tools and materials, as per the specifications of this tender and directions of engineer in charge. , 50p telephone junction box: the scope of work includes supply and installation of 50 pair telephone junction boxwith crone connector with cable entry provision for 1 number of50 pair cable for incomingand 2 numbers of20 pair cableand 1 number of 10 pair cablefor out going, all complete with labour, tools and materials, as per the specifications of this tender and directions of engineer in charge. , 20p telephone junction box: the scope of work includes supply and installation of 20 pair telephone junction boxwith crone connector with cable entry provision for 1 number of 20 pair cablefor incomingand 2 numbers of 10 pair cablefor out going, all complete with labour, tools and materials, as per the specifications of this tender and directions of engineer in charge. , supply of corded telephone: the scope of work includes supply of telephone instruments of model m71corded landline phone of beetel make or equivalent as per the direction of engineer in charge. , supply of cordless telephone: the scope of work includes supply of telephone instruments of model x69n cordless landline phone of beetel make or equivalent as per the direction of engineer in charge. , supply of flameproof telephone:the scope of work includes supply of flameproof telephone instrument as per the specification of this tender and directions of engineer in charge. , fans , ceiling fan: the scope of work includes supply, installation, testing and commissioning of 1200mm sweep bldc ceiling fan ofbajaj / crompton greaves / khaitan / usha / havells / atomberg / equivalent make of following sweep withceiling fan, including wiring the down rod of standard length ( upto 30 cm ) with 1.5 sqmm, pvc insulated, copper conductor, single core cable etc., as required, , as per the specifications of this tender and directions of engineer in charge. , exhaust fan: the scope of work includes supply offresh air fan / exhaust fan of almonard / bajaj / crompton greaves / khaitan / usha / havells / equivalent make of below mentioned sweep andinstallation in existing frames, testing and commissioning offresh air fan / exhaust fan, including lead in wires and accessories as required, all complete with labour and material, with necessary fixing accessories, louvers wherever required, as per the specifications of this tender and directions of engineer in charge. , 300 mm sweep , 450 mm sweep, heavy duty industrial type , upto 450 mm sweep, flp , wall mounted fan: the scope of work includes supply of bldc wall mounted fans of bajaj / crompton greaves / khaitan / usha / havells / atomberg / equivalent make of 400mm sweep and installation, testing and commissioning of wall mounted fan, including wires and accessories as required, all complete with labour and material, necessary fixing accessories, as per the specifications of this tender and directions of engineer in charge. , pedestal fan: the scope of work includes supply ofbldc pedestal fans of bajaj / crompton greaves / khaitan / usha / havells / equivalent make of 400mm sweep and installation, testing and commissioning of the same, including wires and accessories as required, all complete with labour and material, as per the specifications of this tender and directions of engineer in charge. , installation & commissioning of flp / wp fittings: the scope of work includes installation, connection, testing and commissioning of flp / wp type fittings such as junction boxes, welding sockets, lighting panels, convenience outlets / convenience outlets with built in transformer etc, in surface / channel / wall / steel structuresall complete, with labour and tools as per drawings & specifications of this tender and directions of engineer in charge. , weight of the unit upto 2 kg , weight of the unit above 2 kg but upto 5 kg , weight of the unit above 5 kg but upto 10 kg , weight of the unit above 10 kg but upto 20 kg , weight of the unit above 20 kg but upto 50 kg , cable tray , supply of cable trays: the scope of work includes supply of the following sizes of gi cable trays of ladder type / perforated type made out of hot rolled sheet steel of 2mm thick including straight length elbows, tees, crosses, couplers plates etc., as per the specification of this tender and directions of engineer in charge. , upto 50 mm , above 50 mm but upto 100 mm , above 100mm but upto 150 mm , above 150 mmbut upto 300 mm , above 300 mmbut upto 450 mm , installation of cable trays: the scope of work includes installation of the following sizes of gi cable trays of ladder type made out of hot rolled sheet steel of 2mm thick including straight length elbows, tees, crosses, couplers plates, cable tray supports etc., including welding and bolting of cable trays in existing / new supports, all complete with labour and tools, as per the specification of this tender and direction of engineer in charge. , upto 150 mm , above 150 mmbut upto 300 mm , above 300 mmbut upto 450 mm , push button stations , supply : the scope of work includes supply of industrial weather prooftype push button stations with canopy, with start & stop push buttons and ammeter of scale suitable for motor , as per the specifications of this tender and directions of engineer in charge. , supply: the scope of work includes supply of industrial flp type push button stationswith canopy, with start & stop push buttons and ammeter of scale suitable for motor, as per the specifications of this tender and directions of engineer in charge. , supply: the scope of work includes supply of industrial frp type push button stations with canopy, with start & stop push buttons and ammeter of scale suitable for motor, as per the specifications of this tender and directions of engineer in charge. , supply : the scope of work includes supply of industrial weather prooftype push button stations with canopy, with start & stop push buttons, auto / manual switch and ammeter of scale suitable for motor, , as per the specifications of this tender and directions of engineer in charge. , supply: the scope of work includes supply of industrial flp type push button stationswith canopy, with start & stop push buttons, auto / manual switch and ammeter of scale suitable for motor, as per the specifications of this tender and directions of engineer in charge. , supply: the scope of work includes supply of industrial frp type push button stations with canopy, with start & stop push buttons, auto / manual switch and ammeter of scale suitable for motor, as per the specifications of this tender and directions of engineer in charge. , commissioning: the scope of work includes installation, testing & commissioning of wp / frp / flp push button stations, with ms channels grouted with pcc including excavation, alignment, erection and connection of push button, connection of control cable, earthing including supply and fixing of saddles, nuts, bolts etc., painting with two coats of bituminous aluminium paint / synthetic enamel paint over a coat of red oxide primer, including supply of necessary hardware, touch up painting, including supply of paint, including transportation to site at the place of installation, unpacking, using contractors own testing equipments, tools & tackles, all complete with labour , tools and materials, as per the specifications of this tender and directions of engineer in charge. , earthing system , earth pit: the scope of work includes supply , installation , testing and commissioning ofearth pitwith 65 mm dia 3000 mm longearth electrodes , complete with all necessarymaterialsincludingexcavation of earth pit, all civil works, chamber constructions , fillingwith charcoaland salt, back filling , providing cement ( concrete ) slab for earth pits, paintingand markingof earth pit nosand connectionsincluding all labour, tools and materials as per the specifications of this tender and directions of engineer in charge. , earth flat / wire: the scope of work includes supply, installation and connection of following gi earthing strips along the cable trenches or cable trays or fixing to walls or structures and for connecting equipments to the plant grid including welding at joints, providing anti corrosive paint or bitumen and jute covering for welded portion, clamping and necessary hardware for connection etc., including all labour and materials, as per approved drawings, specification of this tender and direction of engineer in charge. , supply of earth flats , 75 x 10 gi earth flat , 25 x 3 gi earth flat , 50 x 10 gi earth flat , 40 x 6 gi earth flat , 25 x 6 gi earth flat , 8 swg wire for earthing , installation of earth flats / gi wire / pvc insulated cable cores the scope of work includes installation ofearth flats / gi wire / pvc insulated single core cablefor earthing with all labour and material including nuts, bolts, washers, aluminium lugs etc , as per the specifications of this tender and directions of engineer in charge. , 75 x 10 gi earth flat , 50 x 10 gi earth flat , 40 x 6 gi earth flat , 25 x 3 gi earth flat , 25 x 6 gi earth flat , 8 swgwire , upto 25 sq.mm cable , above 25 sq.mm upto 70 sq.mm cable , above 70 sq.mm upto 185 sq.mm cable , lighting system , supply of street light poles: the scope of work includes supply of7 m ( above ground ) octagonal gi street light poles of make bajaj / philips / cg / ge / havells / equivalent make with marshalling box to accommodate insulated armoured cablewith terminals, with supply of all necessary accessoriesandmaterial , as per the drawings attached with the tender and direction of engineer in charge. the scope of work also includes supply of suitable cable from fixture to marshalling box but excluding street light fixtures. , installation / commissioning of street light poles: the scope of work includes installation of7 metres street light poles with marshalling box to accommodate 2 nosof4 x 10 sq.mm pvc insulated armoured cablewith elmex connectors, earthing of pole / marshalling box & connecting it to the existing earth grid, but excluding lighting fixtures , including excavation, suitable foundation / mounting arrangement with all labour and tools , as per specifications and drawings attached with the tender and direction engineer in charge. if the street lighting pole is issued as a free issue item to contractor by cpcl, then the contractor is required to shift the lighting pole within the cpcl premesis to the site as per the direction of engineer in charge. the scope of work also includes laying of suitable cable from fixture to marshalling box. , supply of platform light poles: the scope of work includes supply of3 metres gi platform light poleswith supply of all necessary accessories and material, as per the drawings attached with the tender and direction of engineer in charge. the scope of work also includes supply of suitable cable from fixture to marshalling box but excluding light fixtures. , installationof platform light poles: the scope of work includes installation ofplatform light poles with 4 way flp / wp jb including all sundry material as required, painting, welding and all structural works, with all labour and tools , as per the approved drawings, specifications of this tender and directions of engineer in charge. the scope of work also includes installation of cable from fixture to junction box. the scope of work also includes shifting of lighting pole within the cpcl premises to the site as per the direction of engineer in charge. , street light fixtures: the scope of work includes supply of led street light fitting, min. 70w equivalent to crompton model lstp 72 cdl in the existing street light pole. ip66, lumen >100 lm / w, as per the approved makes listed in the tender and necessary mounting accessories, suitablecable glands and support structures, as per the specifications of this tender and directions of engineer in charge. , flp well glass light fixtures: the scope of work includes supply of min. 40w flp well glass led lights of baliga / flexpro / fcg or any other approved makesuitable for mounting with platform poles including supply of suitable flp double compression cable glands, as per drawings and specifications attached with the tender and directions of engineer in charge. , wp well glass light fixtures: the scope of work includes supply of min. 40w wp well glass led lights ofapproved makesuitable for mounting with platform poles including supply of suitable cable glands, as per drawings and specifications attached with the tender and directions of engineer in charge. , flood light fixtures: the scope of work includes supply of min. 100w led flood light equivalent to crompton greaves model, lfln 100 cdl / 60, ip66of approved make, as per the directions of engineer in charge. , flood light fixtures: the scope of work includes supply of 150w led flood light equivalent to crompton greaves model, lfln 150 cdl / 60, ip66of approved make, as per the directions of engineer in charge. , flameproof flood light fixtures:the scope of work includes supply ofmin. 150w led flameproof flood light of baliga / flexpro / fcg or any other approved make including supply of suitable flp double compression cable glands, as per the directions of engineer in charge. , installation oflight fittings: the scope of work includes installation, testing and commissioning of led or conventional bulkhead / well glass fitting / street light fittings / flood light fittings etc, including fixing of control gear, cable glanding, termination and connections in fixtures as per the directions of engineer in charge. , installation upto 6 meters , installation at a height more than 6 meters , removal & relocation of high mast: the scope of work includes the following: a ) dismantling of electrical fittings & cables from high mast and dismantling of high mast from the existing foundation and location b ) construction of foundation for high mast in the new location with suitable foundation bolt according to the existing mast. necessary calculations and drawings for foundation shall be done by the contractor c ) shifting and installation of light fixtures, fixture arangement, mast parts and all other relevant accessories from old location to new location within cpcl premises with all labour and material , as per the approved drawings, specifications of this tender and directions of engineer in charge. , for the above mentioned removal scope , for the above mentioned relocation & installation scope , supply of wp junction box: supply / fabrication of following type dust , vermin proof and weather proof junction / adaptor boxes complete with all fixing hardwares like supports, nuts & bolts, etc including painting.the scope includes all material required to complete the job, as per drawings & specifications of this tender and directions of engineer in charge. , weight of the unit upto 2 kg. , weight of the unit above 2 kg but upto 5 kg. , weight of the unit above 5 kg but upto 10 kg. , supply of flp junction box: supply of following type dust , vermin proof, weather proof and flame proof junction / adaptor boxes complete with all fixing hardwares like supports, nuts & bolts, etc including painting. the number of cable glands holes and cable terminals shall be as per the directions of eic. the scope includes all material required to complete the job, as per drawings & specifications of this tender and directions of engineer in charge. , supply of flp junction box with dimensionupto 420 mm x 420 mm equivalent to type db 31340a in fcg catalogue , supply of flp junction box with dimension above 420 mm x 420 mmto420 mm x 550 mm equivalent to type db 31340ab in fcg catalogue , supply of flp junction box with dimensionupto550 mm x 550 mm ( which are not included in s.no. 2260 and 2270 ) equivalent type to db 31340abs2 in fcg catalogue , civil & structural works , excavation: the scope of work includes excavation of earth for cable laying / laying of gi pipes / earth strip etc., in all types of soil including saturated soil, for a maximum depth of 1.5 m and width approximately 0.5 m, including shoring, shuttering and dewatering ( if necessary it shall be paid separately as per sor ) , backfilling and compacting in layers not exceeding 20 cm thick to the finished ground level, including consolidation and disposal of surplus earth , all complete with labour and tools, as per approved drawings, specifications of this tender and directions of engineer in charge. ( excavated trench dimensions shall be measured ) . , removal of sand from cable trench: the scope of work includes removal of sand from the cable trenchwithout any damage to the cableand disposing it, all complete with labour and tools, as per the specifications of this tender and directions of engineer in charge. , back filling of sand from cable trench: the scope of work includes filling of sand back to trench, all complete with all labour with required tools, as per the specifications of this tender and directions of engineer in charge. , slab removal & relaying: the scope of work includes removal of rcc slabplaced above the cable trench, handlingcarefully without any damage of the slab and cable beneath it and keeping it back in position after laying / removing the cable and sealing the same between rcc covers with cement & sand, including hydra crane ( if required ) , job complete in all respect with labours and tools, as per the specifications of this tender and directions of engineer in charge. , pcc floor cutting: the scope of work includes pcc floor cutting for providing gi conduit laying, earth flat laying, cable laying etc., all complete with labour and tools and the contractor shall carry out the necessary housekeeping in the area as per the specifications of this tender and directions of engineer in charge. , rcc demolishing: the scope of work includes demolishing r.c.c. work for gi pipe laying including stacking of steel bars and disposal of unserviceable material, all complete with labour and tools, as per approved drawings & specifications of this tender and directions of engineer in charge. , dewatering electrical pump: the scope of work includes pumping out of water, including dewatering water mixed with oil / sludge, etc. from cable trenches, depressions etc. by contractors own electrical pump, with cable, labour, hoses, consumables, etc., complete as per the specifications of this tender and directions of engineer in charge. , supply of gi sheet: the scope of work includes supply of gi sheet of 2 mm thick for push button station, field call station, welding receptacle, plant ldb etc as per the the directions of engineer in charge , fabrication & fixing of rainhood for motors: the scope of work includes fabrication and fixing of rainhoods using gi sheet including painting for following rating motors as per the directions of the engineer in charge. , upto 3.7 kw motor , above 5 kw to 18.5 kw , above 18.5 kw to 37 kw , above 37 kw to 55 kw , above 55 kw to 90 kw , above 90 kw to 200 kw , fabrication & fixing of rainhood for miscellenous items: the scope of work includes fabrication and fixing of rainhoods using gi sheet including painting for following miscellaneous items as per the directions of the engineer in charge. , push button stations , welding receptacle , plant ldb , street light jb , telephone / plant communication jb , sfu , structural steel: the scope of work includes supply, fabrication & erection of ms base frames, supports for switchgear, control panels and brackets for miscellaneous electrical equipments, cable tray and cable tray supports out of rolled ms sections, pipe, vertical raceways, plate etc., including welding, bolting, riveting, supply of necessary anchor bolts and grouting, etc., supply & drilling in rcc and fixing of metallic anchor fasteners for supporting cable trays and other miscellaneous switchgear, all complete with labour and materials, as per the specifications of this tender and directions of engineer in charge. , supply , fabrication & erection / installation , supply of paint and applying one coat of anti rust primer and two finished coats of approved synthetic enamel paint for structural steel, all complete with labour, tools and materials, as per the specifications of this tender and directions of engineer in charge. , brick work: the scope of work includes supply and laying of approved 2nd class bricks of thickness 75 mm in cable trench for cable protection as per approved drawings & specifications of this tender and directions of engineer in charge. , chequered plate: the scope of work includes supply, fabrication and installation of 6 mm thick ms chequered plate for covering floor cut outs / cable trenches, etc., including all labour and materials as per approved drawings & specifications of this tender and directions of engineer in charge. , cable markers: the scope of work includes supply and installation of cable markers for under ground cables with 14 swg enamelled steel plate with white letteringon jade green background inclusive of providing and fixingsupports and including all labour and material, as per the specifications of this tender and directions of engineer in charge. , providing and laying plain cement concrete ( pcc ) 1:4:8 by volume ( 1cement : 4 m sand:8 coarse aggregate ) with opc 53 grade and 40mm & down size graded crushed stone aggregates for all depths wherever required like in foundations, fillings , floors, pavements & ramps or any other works etc., including shuttering, tamping, ramming, vibrating, curing, etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete including cement cost etc, all complete as directed by engineer in charge. , providing and laying of reinforced cement concrete ( rcc ) 1:1.5:3 by volume ( 1cement: 1.5 m sand:3 aggregate ) with opc 53 grade and 20mm and down size graded crushed stone aggregate materials for sub structure upto plinth beam levelfor all depths including pavement, machine mixing, curing, consolidating with vibrator, cement cost etcall complete as per instructions of engineer in charge excluding cost of shuttering and reinforcement. , dismantling: , dismantling of switch & sockets: the scope of work includes disconnection and dismantling of all types of switches, sockets and plug points without damage and returning them to our stores or any other place or site within the premises as decided by the engineer in charge, all complete with labour and tools , as per the specifications of this tender and directions of the engineer in charge. , dismantling of trays: the scope of work includes dismantling of following sizes of slotted / ladder type gi cable trays along with straight length elbows, tees, crosses, couplers plates etc., including, cutting, grinding and any other jobs required to dismantle, without any damage and returning it to stores or any other place or site within premises, all complete with labour and tools, as per the specifications of this tender and directions of the engineer in charge. , width upto 300 mm , width above 300 mmbut upto 600 mm , width above 600 mmbut upto 800 mm , dismantling of electrical wiring: the scope of work includes dismantling of electrical wiring ( comprising of single or twin core pvc wires upto 6 sq.mmand single earth wire upto swg ) along with its connected accessories including conduits , casings etc, as per the specifications of this tender and directions of engineer in charge. , dismantling of electrical flp / wp fittings: the scope of work includes disconnection and dismantling of surface / channel / wall / steel structures mounted wp / flp type fittings such as lighting fixtures, push button stations / motor control stations, junction boxes, welding sockets, lighting panels convenience outlets / convenience outlets with built in transformer etc. all complete without damage and returning them to cpcl stores or any other place or site within the premises, including dismantling of any supports, poles, frames or any other structures related to the fittings, as per the specifications of this tender and directions of engineer in charge. , weight of the unit upto 2 kg. , weight of the unit above 2 kg but upto 5 kg , weight of the unit above 5 kg but upto 10 kg , weight of the unit above 10 kg but upto 20 kg , dismantling of platform lighting poles: the scope of work includes disconnection and dismantling of platform light poles ( upto 3 metres height ) along with fittings and shifting it to the stores or to a new location including disconnection of power cable, removal of lighting fixtures and jbs without damage with all labour and tools and as per the specifications of this tender and directions of engineer in charge. , dismantling of street lighting poles: the scope of work includes disconnection and dismantling of street light poles along with fittings and shifting it to the stores or to a new location including disconnection of power cable , dismantling of foundation, excavation, removal of lighting fixtures and jbs without damage with all labour and material and as per the specifications of this tender and directions of engineer in charge. the scope of work includes arranging of necessary heavy duty vehicles like crane, tractor and trailer etc. as required. , dismantling of ht / lt switchgear ( 6.6 kv / 415 v ) : the scope of work includes dismantling of ht panels, lt panels, ups or any other panels as given below, ( i ) including electrical isolation ( i.e. ) disconnection of ht / lt / control cables and deglandingby competent personnel from connected lines ( under the supervision of valid licensed person ) , ( ii ) removal of copper / aluminium bus bars ( both horizontal and vertical ) in the ht / lt panel, ( iii ) removal of all switchgear components like cts, pts, fuses, mcbs, switches, bus bar supports ( insulators ) , relays, terminal boxes, selector switches, transducers, meters, indication lamps, interconnecting wires, nuts, bolts etc. from the dismantled panels. ( iv ) the scope includes dismantling job pretaining to 6.6kv / 415 breakers and shifting to any location within cpcl premises using contractor’s own equipments, tools, tackles, consumables and laboursas per the specification of this tender and directions of engineer in charge. tractor with trailor and hydra charges shall be paid as per the sor based on usage. note: each indicates one feeder and its cable chamber , weight upto 100 kg , above 100 kg upto 500 kg , above 500 kg upto 1000 kg , above 1000 kg upto 1500 kg , dismantling of ht softstarter ( 6.6 kv ) : the scope of work includes dismantling of ht softstarter of weight upto 3500 kg as given below, ( i ) including electrical isolation ( i.e. ) disconnection of ht / lt / control cables and deglandingby competent personnel from connected lines ( under the supervision of valid licensed person ) , ( ii ) removal of copper / aluminium bus bars in thepanel, ( iii ) removal of all switchgear components like cts, pts, fuses, mcbs, switches, bus bar supports ( insulators ) , relays, terminal boxes, selector switches, transducers, meters, indication lamps, interconnecting wires, nuts, bolts etc. from the dismantled panels. ( iv ) the scope includes dismastling job pretaining to 6.6kv breakers. within cpcl premises using contractor’s own equipments, tools, tackles, consumables and laboursas per the specification of this tender and directions of engineer in charge. the scope shall also include shifting of panel from substation to any other place inside the cpcl premises with all neccessary vehicles like tractor trailor, hydra, crane etc and manpower as per the requirements. , dismantling of structures: the scope of work includes dismantling of any support structures at ground level. the scope of work includes removal of structures from the ground support by welding / cutting, all complete with labour and tools, as per the specifications of this tender and directions of engineer in charge. , stencilling:the scope of work includes stencilling of letters / numbers on panels, cable drums etc., as per the directions of engineer in charge including all labour and materials. , letter / number of size up to 2 , letter / number of size above 2 to 4 , letter / number of size above 4 to 6 , dismantling of cables: the scope of work includes dismantling / pulling out the lt / ht, pvc / xlpe, power / control / telephone / computer, armoured / unarmoured cables of various voltage grades / types / sizes / makes from the trench ( upto 1.5 metres deep ) / pipes / structures / racks or trays, all complete with labour and tools. the scope also includes disconnection, deglanding, declamping of cables ( if required ) as per the directions of engineer in charge. , overall diameter upto 35 mm , overall diameter above 35 mm but upto 55 mm , overall diameter above 55 mm but upto 75 mm , overall diameter above 75 mm , cable dismantling and relaying:cable dismantling / pulling out of lt / ht, pvc / xlpe power / control / telephone / computer , armoured / unarmoured cables of various volatge grades / sizes from trench / pipes / structures / racks or trays and declamping, rerouting and relaying of cable for reglanding etc. as per the directions of engineer in charge. for 2c, 3c, 4c cables below rates of 3.5c cables will be applicable , all lv control cables and lv power cables upto 3.5c x25 sq.mm , lv power cables above 3.5c x 25 sq.mm upto 3.5c x 95 sq.mm , lv power cables above 3.5c x 95 sq.mm upto 3.5c x 185 sq.mm , lv power cables above 3.5c x 185 sq.mm upto 3.5c x 300 sq.mm , single core lv power cable upto 1000 sq.mm , single core ht cable upto 1000 sq.mm , ht cables from 3c x 120 sq.mm upto 3c x 185 sq.mm , ht cables from 3c x 240 sq.mm upto 3c x 300 sq.mm , retrieving of cables: the scope of work includes uncoiling of cables from damaged cable drums / retreiving of cables from broken drums / scrap, without causing any damage to the cables, all complete with labour and accessories required for the job, as per the specifications of this tender and directions of engineer in charge. job also includes disposal of the broken drums. necessary crane, tractor with trailer shall be arranged by the contractor. , overall diameter upto 25 mm , overall diameter above 25 mm but upto 35 mm , overall diameter above 35 mm but upto 45 mm , overall diameter above 45 mm but upto 55 mm , overall diameter above 55 mm but upto 75 mm , re rolling of healthy cables: the scope of work includes re rolling of healthy loose cables onto cable drums / empty drums, measuring and marking the length, providing end caps etc. without causing any damage to the cables and drums, all complete with labour and accessories required for the job, as per the specifications of this tender and directions of engineer in charge. ( cable drums will be provided by cpcl ) , overall diameter upto 25 mm , overall diameter above 25 mm but upto 35 mm , overall diameter above 35 mm but upto 45 mm , overall diameter above 45 mm but upto 55 mm , overall diameter above 55 mm but upto 75 mm , cable dressing:the scope of work includes cable dressing in trays, structures / channels / walls etc. dressing of cables shall be done with suitable clamps, fasteners of gi or aluminium at an uniform interval of 1 metre with all labour and materials, as per the instructions of eic , cable trays upto 150 mm wide , cable trays 300 mm to 450 mm wide , cable trays above 450 mm to 600 mm wide , cable trays above 600 mm to 750 mm , hiring of heavy duty vehicles , the scope of work includes hiring of 20 feet trailer with tractor ( on daily basis ) on workingdays on 8hrs shift, inclusive of driver, one assistant, consumables like diesel etc., with all safety instruments as per the specifications of this tender and directions of engineer in charge. all required tools, tackles, wire ropes, pulley blocks, belts, chains etc., for lifting, aligning, tying, stacking shall be arranged by contractor. 1vehicle day = 1 vehicle x 1 day ( 8hrs ) . , the scope of work includes hiring of 12t hydra ( escorts make f 17 model or equivalent ) on daily basis on working days on 8hrs shiift, inclusive of driver, one assistant, consumables like diesel etc., with all safety instrumentsas per the specifications of this tender and directions of engineer in charge. all required tools, tackles, wire ropes, pulley blocks, belts, chains etc., for lifting, aligning, tying, stacking shall be arranged by contractor. 1vehicle day = 1 vehicle x 1 day ( 8hrs ) . , manpower assistance: the scope of work includes supply of labour classified under the following categories as and when required, as per the specifications of this tender and directions of engineer in charge. , full day work , highly skilled , skilled , semi skilled , unskilled , over time work , highly skilled , skilled , semi skilled , unskilled , supply of inverter air conditioning unit: the scope of work includes supply of minimum 3 star inverter split air conditioning units of following tonnage of any approved make including any other hardwares and consumables required forcomplete installation as per specifications of this tender and directions of engineer in charge. , 1.5 tonnes , 2 tonnes , installation of air conditioning unit: the scope of work includes installation ofinverter or split air conditioning units with all related accessories as per specifications of this tender and directions of engineer in charge. , 1.5 tonnes , 2 tonnes , supply & installation of stabilizers: the scope of work includes supply , installation and commissioning of voltage stabilizers of below mentioned ratings of v guard or equivalent approved make, for ac unitsas per specifications of this tender and directions of engineer in charge. , 4 kva for 1.5 ton inverter ac , 5 kva for 2 ton inverter ac , ac repair & miscellaneous works: . , supply and fixing of stand for outdoor units of 1 / 1.5 / 2 ton split ac , supply and fixing of copper tube size 3 / 4 and 3 / 8 ( soft pipe ) for ac unit , the scope of work includes removal of window / split ac units as perscope of work and as per direction of engineer in charge , cost towards healthiness checking of ac unit ( window / split ac ) , gas charging of 1 / 1.5 / 2 ton split ac including all materials, labour and tools as per the directions of engineer in charge , supply, installation / commissioning of cassette unit: the scope of work includes supply, installation of indoor, factory assembled, cassette type air conditioning unit, rotary / scroll compressors, evaporator, remote air cooled condenser coil ( outdoor unit ) , refrigeration components, thermostats, controls, diagnostics, safety devices, accessories and suitable for operation in high ambient temperatures ( upto 115 deg f ) and coastal environments; indoor and outdoor units shall be factory pressure tested, run tested and supplied inclusive of full operating charge of gas.the capacity as follows. supply and installation shall be as per the specifications of this tender and directions of engineer in charge. , supply of 1.5 tr cassette type air conditioner , supply of 2.0 tr cassette type air conditioner , installation / commissioning of 1.5 tr cassette type air conditioner , installation / commissioning of 2.0 tr cassette type air conditioner , fire proof coating of cables , supply of hilti or equivalent make indoor application fire proof paint for 40 minutes fire retardant capacity for all cables cp678 ( weight of 20 kgs each box ) , supply of hilti or equivalentmake outdoor application fire proof paint for 40 minutes fire retardant capacity for all cables cp679a ( weight of 20 kgs each box ) , applying of fire proof paint over cables as per the directions of engineer in charge inclusive of all consumables & labour required , supply of meters / transformer : the scope of work includes supply of following type of meters / transformers as per approved vendor list, specifications of this tender and directions of engineer in charge: , three phase multifunction meter, ac 110v, 230v, 440 v ( make: rishab / schneider / conzerv / equivalent ) , programmable multifunction transducer ( rishabh m40 or equivalent ) , aux. supply: 85 230v ac / dc , analogue ammeter ( ae / rishab / schneider / meco / equivalent ) , analogue voltmeter ( ae / rishab / schneider / meco / equivalent ) , ht panel testing and commissioning: the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments to site for ( a ) carrying out secondary injection testing of protection relays ( b ) injection testing of 6.6kv current transformers ( c ) ht breaker servicing & testing including buffer replacement, measuring of crm, closing / tripping time etc ( d ) panel wiring checks including retermination, dressing as required the scope of work also includes submission of test reports and as built drawings as per the specification of tender and engineer in charge , differential stability test: the scope of work includes carrying out differential stability test for transformers, cables, ht busincluding supply of manpower along with all tools & testing equipments, as per the directions of engineer in charge . the scope of work also includes submission of test reports and as built drawings , lt panel testing and commissioning ( breaker feeder ) : the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments to site for ( a ) carrying out secondary injection testing of protection relays ( b ) injection testing of 415 v current transformers ( c ) measurement of ir values ( d ) lt breaker servicing & testing including buffer replacement, measuring of crm, closing / tripping time etc ( e ) panel wiring checks including retermination, dressing as required the scope of work also includes submission of test report and as built drawings as per the specification of tender and engineer in charge , lt panel testing and commissioning ( contactor feeder ) : the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments for ( a ) carrying out secondary injection testing of protection relays ( b ) injection testing of 415 v current transformers ( c ) measurement of ir values ( d ) panel wiring checks including retermination, dressing as required the scope of work also includes submission of test report and as built drawings as per the specification of tender and engineer in charge , transformer testing: the scope of work includes testing of transformers including all labour and materials, as per the specifications of this tender and directions of engineer in charge and shall submit the test reports. testing of transformer shall include the following test as a minimum requirement: *transformer winding resistance measurement *transformer ratio test *checking various alarms and trips *testing of the bucholz relay *oil breakdown voltage testing *measurement of insulation resistance *dielectric tests of transformer *tests on on load / off load tap changer *oil pressure test on transformer to check against leakages past joints and gaskets , cable hipot testing: the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments for cable hipot testing of 6.6 kv cables and submission of test reports as per the direction of engineer in charge. each shall indicate each cable. , numerical relay testing: the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments for numerical relay testing . the scope also includes submission of test reports as per the directions of engineer in charge.the scope of work shall include arrangement of manpower along with all tools, consumables & testing equipments , ht breaker testing :the scope of work includes ht breaker testing includingmeasuring of crm, closing / tripping time etc all complete with labour and materials as per the directions of engineer in charge. the scope of work shall include arrangement of manpower along with all tools & testing equipments. , lt breaker testing :the scope of work includes lt breaker testing includingmeasuring of crm, closing / tripping time etc all complete with labour and materials as per the directions of engineer in charge. the scope of work shall include arrangement of manpower along with all tools & testing equipments. , ht breaker servicing :the scope of work includes ht breaker servicing includingbuffer replacement all complete with labour and materials as per the directions of engineer in charge. the scope of work shall include arrangement of manpower along with all tools. , lt breaker servicing :the scope of work includes lt breaker servicing includingbuffer replacement all complete with labour and materials as per the directions of engineer in charge. the scope of work shall include arrangement of manpower along with all tools. , the scope of work includes supply and installation of zip type heat shrinkable outer sleeves for 6.6 kv / 11kv cables as per the details below, specifications of this tender and directions of engineer in charge: , overall diameter above 40mm upto 110mm, standard length 965mm , overall diameter above 57mm upto 145mm, standard length 1100mm , the scope of work includes supply of self amalgamating ht tapes of scapa or equivalent make, as per the directions of engineer in charge , rubber mat: the scope of work includes supply and laying of 900 mm wide safety insulation mats complying to is 15652, of following grades required for maintenance of electrical equipment in substation, including cutting to required shape in running length, including all labour and materials, as per applicable indian or international standards and cea guidelines and as per directions of engineer in charge. , 3.3 kv grade. , 11 kv grade. , the scope of work includes supply of following eqiupments as per approved vendor list, specifications of this tender and directions of engineer in charge: , led indication lamps, wide band ( 24 240v ac / dc ) , siemens / l&t / teknic / equivalent make , local / remote selector switch of salzer / kaycee / equivalent make , the scope of work includes supply of fm1 / quartz time switch 240v ac base / din mounting as per the specification of this tender and engineer in charge , the scope of work includes supply of digital time switch 240v ac base / din mounting as per the specification of this tender and engineer in charge , erection and dismantling of steel scaffolding:erection and dismantling of steel scaffolding at the required locations as directed by engineer in charge ( e.i.c ) using supply of 1.5 dia steel tubular pipes with suitable clamping arrangement, providing steel gratings at the required locations firmly tied on to the scaffolding pipes and to the satisfaction of e.i.c and removal / dismantling of the steel scaffolding materials on completion of the job. the job also includes supply of scaffolding materials, all types of tools andtackles, lifting arrangements like chain pulley blocks, all consumables and required labour to complete the job in all respects, including transportation of materials and steel gratings up to the work site. , erection and dismantling upto 5 meters height of scaffolding , erection and dismantling above 5 meters upto 10 meters height of scaffolding , erection and dismantling above 10 meters upto 20 meters height of scaffolding , shifting of package substation: the scope of work includes dismantling, shifting and re installation of existing package substationincluding all labour and tools, as per the specifications of this tender and directions of engineer in charge. the scope includes arranging of necessary crane, tractor, trailor, slings etc.by the contractor but excludes civil jobs for re installation. , supply of transformer oil : the scope of work includes the supply of transformer oil as per is 335 standard. routine and type test certificate shall be submitted along with supply of transformer oil , transformer oil filtration: the scope of work includes charges for transformer oil filtration per litre per circulation as per the tender document. the scope also includes testing of initial and final ( after filtration ) breakdown values bdv of transformer oil, transportation charges for filter machine etc. ( cost shall be inclusive of vehicle transportation charges, retention charges ( if any ) ) , supply of wp cable gland: the scope of work includes supply of weather proof cable glands as per the specifications of this tender and directions of engineer in charge. , overall diameter upto 19 mm ( 0.75 inch ) , overall diameter above 19 mm but upto 25 mm ( 1.0 inch ) , overall diameter above 25 mm but upto 32 mm ( 1.25 inch ) , overall diameter above 32 mm but upto 38 mm ( 1.5 inch ) , overall diameter above 38 mm but upto 51 mm ( 2.0 inch ) , overall diameter above 51 mm but upto 64 mm ( 2.5 inch ) , overall diameter above 64 mm but upto 76 mm ( 3.0 inch ) , supply of flp cable gland: the scope of work includes supply of double compression flameproof cable glands as per the specifications of this tender and directions of engineer in charge. , overall diameter upto 19 mm ( 0.75 inch ) , overall diameter above 19 mm but upto 25 mm ( 1.0 inch ) , overall diameter above 25 mm but upto 32 mm ( 1.25 inch ) , overall diameter above 32 mm but upto 38 mm ( 1.5 inch ) , overall diameter above 38 mm but upto 51 mm ( 2.0 inch ) , overall diameter above 51 mm but upto 64 mm ( 2.5 inch ) , overall diameter above 64 mm but upto 76 mm ( 3.0 inch ) , supply of monobloc pumps: the scope of work includes the supply of monobloc pumps of 1 hp along with required accessories as per the specification of this tender and directions of engineer in charge , supply of trefoil clamp: the scope of work includes the supply of trefoil clamp along with required accessories as per the specification of this tender and directions of engineer in charge , supply of flexible cables: the scope of work includes supply of unarmoured flexible copper cable, pvc insulated as per the specifications of this tender and directions of engineer in charge. , 3c x 1.5 sq.mm , 3c x 2.5 sq.mm , 4c x 2.5 sq.mm , 4c x 4 sq.mm , 4c x 6 sq.mm , supply of ladder: the scope of work includes supply of min. 8 feet frp ladder as per the specification of this tender and directions of engineer in charge , supply of distillation water unit: the scope of work includes supply of distilled water still with three heaters, heater details: 6 kw, 230 v, capacity : 8 litres / hr , servicing of ht megger: the scope of work includes servicing of ht megger with necessary parts and battery replacement as per the specification of this tender and directions of engineer in charge , shifting of scrap / miscellaneous items: the scope of work includes shifting of scrap / miscellaneous items anywhere within cpcl premises, all complete with labour and tools, as per the specifications of this tender and directions of engineer in charge. => limited...

Town Panchayats - Tamil Nadu

33060428 construction of modern lpg gasifier crematorium at ward no 2 survey no 234 1, 234 3 kayalpartinam south part village burial ground in thiruchendur road, arumuganeri town panchayat, thoothukudi district. , earth work excavation for foundation in all types of soils and sub soils to full depth ( such as soils in rock / silt / light black cotton soil / ordinary soil ) except in rock requiring blasting but inclusive of shoring, shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth other than sand in layers of 150 mm thick well rammed and consolidated, depositing the surplus earth in places shown by the departmental officers with initial lead of 10 m and initial lift of 2 m. complete as per tnss23 & 24, v, vi ( s2 ) , vii, 9, 10 , gravek soil i depth of 2 mt , ii depth of 2 mt 3 mt , supply delivery and filling ofstone dust in layer of not more than 15cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyance of sand at site and all labour charges and all other incidential charges etc., complete as per standard specification tnss no. 24 & 25. , plain cement concrete of mix 1 : 4 : 8 ( one part of cement four part of sand eight part of aggregates ) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. tndss no: 28 v, vi ( s2 ) v, vi ( s5a ) vii , supplying and fillingofu / s gravelfromapprovedquarry in layer of not more than 15cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyance of sand at site and all labour charges and all other incidential charges etc., complete as per standard specification. , supplying anderrectingsteel centering including necessary supportsfor plain surfaces for reinforced cement concrete works such as coloumn footing, coloumn pedestals, plith beams, grade beams, staircase steps, etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorscomplying with standard specification without strutting. ( tnss no or nbc no 30 ( s ) 86 86 a v, vi ( s3 ) vii , belowground level , ground floor , column , supplying ribbed tor steel rodsincluding cutting cranking fabricating assembling laying in exact position tying with soft steel wire 16 or 18 bwg etc. complete for all rcc works.as per the design given including cost ofsteel and binding wire also in all floors as per standard specification. ss86 & 86a, v, vi ( s3 ) ( s6 ) vii. , providing and laying in position standardised concrete mix m 20 grade in accordance with is 456 2000 using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement contenet of 325kg / cum and maximum water cement ratio of 0.55 including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about ( 5.0cum ) , 7730kg of 20mm machine crushed stone jelly and with about ( 3.3 cum ) , 5156kg of 10 12mm machine crushed stone jelly and with about ( 4.79cum ) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers the coarse and fine aggregates to be used should comply with the requiremnents of is standards. ( no separate payment will be made by the department for the excess usage of materials ) footing, plinth beam, tie beam / lintel, ground floor roof beam, salbs, sloped roof beam and slabs30 v, vi ( s5 ) vii & 13 , below ground level , ground floor 0.00 mt to 4.50mt , plain cement concrete 1:8:16 ( one cement eight fine aggregates and sixteen coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification 30 v, vi ( s5 ) vii & 13 , brick work in cm 1:5 ( one cement & five sand ) using iiclass ground moulded bricks of size 9x43 / 8x 23 / 4 standard specification including finishing, curing, etc., complete complying with standard specification 31 & similar to 31c v, vi ( s5 ) vii , below ground level , ground floor , first floor , brick partition walls of 10.80cm thickness using best quality country bricks of size 8 3 / 4 x 4 1 / 4 x 2 3 / 4 in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. ( hoop iron reinforcement will be measured and paid for separately ) , specialplastering in cement mortor 1:3 mix ( one cement, , three sand ) 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.tndss no: 56, 57 , weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.61 v vi, ( via ) 3 , finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in cement mortar 1:3 ( one cement add three sand ) 12 mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification and as directed by the deparmental officers 44 h v, vi, ( s5a ) vii , 3 , paving the floor with best approved quality fine polished kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 ( one cement and three sand ) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification.39 a , paving the floor with pre polished concrete anti skid tiles ( required shape and design ) of 20mm thick of approved quality and colour laid in cement mortar 1:3 ( one cement and three sand ) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) , vibrated plain cement concrete 1:2:4 ( one cement, two sand and four hard broken stone jelly ) using 20 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. ( the rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers 30 v, vi ( s5 ) vii & 13 , plastering in cement mortor 1:5 mix ( one part of cement, , five part of sand ) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.tndss no: 56, 57 , supplying and painting the new plastered walls with two coats of exterior emulsion paint ( weather proof ) first class quality and of approved colour over a priming coat including thorough scrapping clean removal of dirt etc. complete and including necessary plaster paris putty etc. wherever required.as per ( isi std ) ( it mustprovide excellent resistance against the growth of algae and fungi on the walls. and it must offer excellent protection against alkali and uv degradation and the durability period should be 5 years. 61 v, vi ( s4 ) 3 , providing upvc ( un plasticized polyvinyl chloride ) door: providing and fixing casement doors fabricated from un plasticized polyvinyl chloride ( upvc ) sections. profiles: the profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. the window unit should be designed with all corner joints mitred and fusion welded. windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. the sash should be of 60 x 102mm. the mullion should be of 60 x 74mm. the profiles should have co extruded seals. hardware: all the hardware like friction stays, handles should be screwed with self tapping screws. the handles, locks should be designed so that they cannot be released from outside. glazing: the window system should be glazed with 5mm plain float glass / 6mm bison lam installation: the profiles should be cut to length and welded 45 degrees. the window should be designed such that the water drainage does not pass through the reinforcement chamber. the window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug. ( pwd sor page no.65 s.i no.264 ) , supplying and fixing of rolling shutters shall be pull and push type ( mannually operated ) made of 18g / 3 lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. these five main parts are made out of special components detailed below: curtain shall be of 18g / 3 lath sections cut to required size and filled with heavy cast iron / ms clips. for 80 ( 2.45m ) high rolling shutter lath sections provided shall be not less than 37 numbers. lock plate shall be 10g ms sheet and attached to the side brackets with 20mm square bar.side brackets shall be of 10g ms plate and cast iron u clamps shall be rivetted to the side brackets. roller shall be of heavy cast iron pullies fitted with heavy duty c class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. side brackets shall be of 10g ms plate and cast iron u clamps shall be rivetted to the side brackets. hood cover shall be of 0.8mm crca sheet reinforced with 25mmx25mmx3mm ms angle or gate channel. the rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete. , supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mmboth profiles are reinforced with gi / 1mm 125gsm and100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( blackcolour ) covered with all over the edges of frame and shutter.the corners and joints should be welded and cleaned.radiations pin headed glass 4mm thick should be provided inthe louvers. the window should be fixed to the wall with100% packing with screws and silicon packing all round theframes. the ventilator should be got approved from theexecutive engineer before use on work pwd sorpage no : 66 , supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 25gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work page no : 65, sl no: 265 , supplying & fixingdoor shutters for solid core flush shutters with teak ply on both side with teak wood lipping alround 35mm thick, single leaf confirming to is:12406 / 1989 with 35x12mm t.w. lipping on all edges with necessary adhesives and cp screws complying with standard specifications. the rate is inclusive ofthreee coats of best quality varnish but excluding cost of furniture fittings, such as 300 mm tower bolt 2nos, 200mm towerbolt 1 no. 300mm aldrop 1 no. alu handle ornamental type 2 nos and 1no.door stopper etc complete. page no : 42 sl. no : 121 , supply and fixing of stainless steel ( salem stainless steel ) door frame ( box section using stainless steel plate of 1.6mm thick ) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc. pwd sor page no:: 44sl. no: 131 , manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete pwd sor page no:: 57sl. no: 131 , supply and fixing of m.s grills for windows, with one coat of red oxideprimer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specification. including phosphating as per isi with rust preventive primer & ready to assemble condition for easy installation at site including dismantlingmaking necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. and steel doorcomplete as directed by the departmental officer. , painting the new iron works such as steel doors, windows, ventilators windows bars, balustrades etc, in all floor withtwo coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand ( to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc, complete complying with standard specification. ( the make, quality and colour of paint should be got approved bythe engineer in charge before use on works ) ( tnss no or nbc no 61 v vi ( 54 ) 3 ) , painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. ( the make, quality and colour of paint should be got approved by the executive engineer before use on works. ) , dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in cement mortar 1:2 ( one cement and two sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 39a , supplying, fabricating, erecting structural steel work for roofing welded or bolted type using ms channels, angles, plates and round bars etc. conforming to is specification including primer coating and enamal painting as per design given by the departmental officers etc, complete as per standard specification , fabricating supplying and fixing of pre painted galvanium iron sheets with the following specification. the materials should be of ppgi tile profile with a red colour or any other approved design 0.47mm thick 24 guage having width 1050 mm. the sheet should be g.i.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws, plastic washer.the washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of z 120 gsm paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. the sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. , supplying and fixing in positon indian water closet ( oriya type ) of size 580 x 440mm white glazed earthern ware of approved quality and brand with p or s trap conforming to bis with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one lime, two sand and five brick jelly ) 100mm thick and finishing the top to the required slope and including giving necessary connection to ci soil pipes ( including the cost of 100mm dia ci pipe for a length of 600mm ) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. ( the water closet should be got approved by the executive engineer before use on works ) . , supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm ( with pedestal / without pedestal ) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. ( the wash hand basin and specials should be got approved by the executive engineer before use on works ) . , supplying and fixing in position white / colour glazed european water closet of best quality and approved make with 100 mm p or s trap connecting with ci pipe of 100mm dia / pvc pipe of 110mm dia, double flapped rigid pvc black seat and seat cover with cp brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity pvc / 12.5 litres capacity porcelin low level flushing tank with a pair of ci brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white pvc flush hand using indian adopter joint including all internal fittings uch as 15mm brass connections, 15mm gm wheel valve, 15mm brass nipple ( 2 nos. ) , 15mm nylon connection, tw plugs, screws and also giving necessary connection to the pvc pipe including cost of 600mm length of 110mm dia pvc pipe and painting the ci brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re doing the dismantled masonry to original condition etc. complete complying with standard specifications. ( the ewc and flushing tank wiht all accessories should be got approved by the executive enginer before use on works ) , supplyingandfixingin position best approvedof bis quality 110mm p.v.c rainwaterdownfallpipe having a pressure of 4kg / sq.cm including cost of necessary pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc, and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc, complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of uclamp at the centre of the pipe line in addition to those for more than 3.00mt pipe length etc, completecomplyingwithstandardspecifications. , conducting geophysical survey, quality and quantity test and transportation charges etc, ( this includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist ) , drilling150 mmdiaborewellin hard rock areas anywhere in the state inculding transportation to site of work in hardrock areas inculding labour charges for insertion of ms casing pipe and flushing of borewell and for minutes. , upto 150m below g.l. , from151m 180 m , from181m 210 m , from211m 240 m , supply and delivery of unplasticised ribbed screen pvc casing pipe of the 150mm dia in 3m length with screwed and socket end and centering guide for every 15m length of pipes as per is / 12818 / 92 and as amended from time to time to suit the borewell upto 80m depth ( c.s ) with isi marking including, loading, unloading , freight, stacking and transit insurance charges etc, complete.twad page no : 22 , supplyanddelivery of three phaseof50 lpm175 mtr head submersible pumpset of motor isi / isowith threephase panel board with two level guard and auto startas per isi specificationsincluding all cost and conveyance to site etc., complete , three phaseof50 lpm175 mtr head submersible pumpset twad page no : 98 , supply and delivery of three phase panel board star delta with two level guard and auto start suitable for submersible pumpsets and accessories including all fittings suitable for submersible pump sets.panel board should be provided as per specification. rates inclusive of packing, loading, freight, unloading, stacking, transit andinsurance charges etc, complete twad page no : 110 , supply and delivery offollowing 50 mm dia upvc column pipe and gi pipes and other special materials of good quality includingcost of materials and labour with cost for coveyence to site etccompletecomplyingwith standardspecifications. etc., , 50mm dia upvc column pipe twad page no : 24 , 50mm upvc . elbow pwd page no : 107 , 50mm upvc . union , 50mm upvcbend , 50mm gate valve twad page no : 45 , 50mm gm n.r.v twad page no : 45 , 50mm pvc mta twad page no : 27 , 50mm end pvc cap pwdpage no : 100 , 50mm dia gi flange set twad page no : 44 , 50mm m.s. clamp set twad page no : 44 , supplying and fixing of pvc insulated and sheathed 3 core 4sq.mm flat type copper cable cofirming to is 694 / 1990 and including cost and conveyance of all materials to site and labour charges etc, complete as per standard specification. twad page no ; 116 , labour charges for the erection of 50 lpm175 mtr head submersible pumpsetin borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of tnicn switches starter, voltmeter, ammeter, three pilot lamps capacitor single phasing preventor, water level guard and laying and jionting the cables andtwin earthing as per ie rules., complete and testing the pumpset and trail run for 10 days. twad page no287 , supplying laying and jointing pvc pipes of approved quality and best varity of b class pipe of the following sizes including fixing g.i specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. the pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red oxide primer etc., complete. , 32 mm dia, pvc pipe , 20 mmdia, pvcpipe , 32mm pvc.elbow , 32mm pvc. bend , 32mm pvc. tee , 32mm pvc. end cap , 20mm pvc. bend , 20mm pvc.elbow , 20mm pvc. tee , 32mmx20mm pvc.reducertee , suppling and fixing in position15mm.diameter pvc screw down tap ( heavy duty ) of approved make conforming to i.s.specifications and quality including cost of shellac , thread etc.complying with standard specifications and including cutting and threading wherever necessary. , supplying and fixing in position first quality and approved variety of 32mm gun metal gate valve ( heavy type ) with i.s.i.mark of the following sizes including cost of shellac , thread etc, .including labour for cutting and threading of g.i.pipes etc., complete complying with standard specifications for both internal and external water supply arrangements. , supplying and fixing positionpvc nahani trap ( pvc nahani trap of size 100 x 75mm ) with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( one part of lime, two part of sand and five part of 40mm gauge brick jelly ) and finished with cement mortar 1:3 ( one cement, three sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the ci / pvc pipes, etc., complete complying with standard specification. ( the nahani trap should be got approved by the executive engineer before use on works ) , supplying and fixing in position best quality 110mm dia p.v.c soil / waste pipes ( 6ksc ) with specialshaving isi mark and providing leakproof joints including fixing to the wall with p.v.c / m.s clamps etc., and making connection to all sanitaryfittings, dismandling masonry / r.c.c. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications. , 110 mm dia pvc pipe , 110 mm dia pvc ellbow , 110 mm dia pvc tee , 110mm dia pvc door elbow pwd pg.no:102 , 110mm dia pvc door tee , 110mm dia pvc door yee , 90 mm dia pvc pipe , 90mm dia pvc elbow , 90mm dia pvc tee , 90mm dia pvc door elbow pwd pg.no:102 , 90mm dia pvc door tee , 90mm dia pvc door yee , supplying and fixing of 2000 liters capacity hdpe tank with is specification is 10701 / 96 the tank is meant for outdoor ( or ) indoor use complete with removable hinged top locking arrangement and to make provision to fix water supply pipe lines, necessary man hole with cover and including all pvc specials pugs, screws nails to fix the tank etc., complete and the tank should fixedfirming as directed by the departmental officers.the rate shall be inclusive of all materials, labour conveyance hoisting and fixing charges etc. ( the water tank should be got approved by the eebefore use on work. twad page no ; 85 , supplying and fixing in position c.i.manhole covers ( light or heavy duty ) of 600 x 600mm in size of best approved quality and as per standard specifications etc., complete. , supplying and fixing pvc ventilating shaft of 110mm dia ( having working pressure 4 kg. / sq.cm ) with 3 metre height including cost of pvc cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers , supplying and fixing in position indian make bewelled edge mirror of approved quality and brand of size 600 x 450mm wth necessary plastic back, pvc frame with bottom stand of approved colour with brass screws, rawal plugs etc., complete complying with standard specifications. , supplying and fixingbest approved quality brass c.p / al anodised towel rail 600mm. long and 20mm diameter with brackets of same material including cost of teak wood plugs and c.p.screws etc., complete complying with standard specifications , supplying and fixing best approved quality c.p.soap tray of size 150mm x 100mm including cost of teak woodplugs, brass screws complete complying with standardspecifications. , supply and laying of3.5 x 35 sq.mm pvc armoured ltugcable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt.layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.twad page no ; 116 , wiring with 2 x 1.5 sqmm ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 3mm thick hylum sheet cover with tw switch box and 5a f.t. switch with continuous earth wire connection of 14 swg tc wire for making good of the concealed portion with suitable colour for pvc concealed light point / fan point ( for electronic regulator ) . etc, complete as per standard specifications. sd 24 , wiring with 2 x 1.5 sqmm ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 150 x 100 x 113 mm tw switch box with 3mm hylum sheet cover for5a 3 pin non inter locking cs plug with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed pvc plug point.etc, complete as per standard specificationssd 38 , wiring with 2 x 4sqmm ( 56 / 0.3 ) pvc insulated single core unsheathed copper conductor cable of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories inflush with wall with 150 x 100 x 113 mm tw switch box with 3mm hylum sheet cover for15a 3 pin non inter locking cs plug with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour for concealed pvc power plug point. etc, complete as per standard specifications. sd 40 , supply and run of 2 of 1.5 sqmm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 swg tc wire and making good of the concealed portion with suitable colour.etc, complete as per standard specifications sd 54 , earthing as per p.w.d. standard with an earth electrode of 2mtr. class b gi pipe of dia not less than 32mm complete with necessary masonry work. etc, complete as per standard specificationssd 234 , supply and fixing of 3 phase 4 wire 4 way icdb of 32 a per way with 100 a tpn mc switch with suitable trunking box ms cable entry boxes and internal connection on suitable angle iron frame work with earth connection etc, complete as per standard specificationssd. 175 , supply and fixing of horizontal type 4 way triple pole neutral mcb distribution board in sheet steel enclosure with 40 a 4 pole mcb isolater as incoming and 12 nos. 6a to 32 a sp mcb as outgoing in flush with wall and making good of the concealed portion with earth connection. the mcbdb and mcbs should be with the isi mark etc, complete as per standard specificationssd.179 , supply and run of 2 of no.8 swg gi wire for guarding with cradle with no.8 swg gi wire at the equal interval of 1.5m etc, complete as per standard specifications sd.75 , supply and run of 4 x6 sq.mm ( 84 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade on 7 / 20 gl bearer wire for service connection mains etc, complete as per standard specifications.sd 68 , supplying and laying of pvc insulated, pvc sheathed, armoured, ltug cable of size 2 core 10 sqmm al.cable clamped on walls ( sd 210 ) , supplying and fixng of cable gland and termination with earth connection of size 2 core 10 sqmm etc, complete as per standard specification. ( sd 182 ) , supply and fixing of tneb board suitable for 3 phases 63a service connection made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 / 2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 nos 63a fuse units ( 500v ) 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 7 / 16 pvc insulated copper wire with earth connection complete.sd 129 , supply and fixing of 32 a tpn mc switch on incoming and 3 nos 32 a dpmc switch ( front handle ) as outgoing with suitable adoptor box with suitable ms cable entry box trunking boxes and internal connections on internal connections on suitable ai frame work with earth connection etc, complete.sd 172 , supply and fixing of 3 phase 4 wire 4 way icdb of 16 a per way with 32 a tpn mc switch with suitable ms cable entry boxes trunking box and internal connections on suitable angle iron frame work with pwd earthing etc, complete.sd 173 , earthing as per the isi specification with an earth electrode of 2.1mt class b gi pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry . sd 233 , supply and run of 2 of 4sqmm ( 56 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14swg cuwireand making good of the concealed portion with suitable colour ( sd57 ) , supplying and laying of 3½ x 50 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 m putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ sd 200 ] , supplying of 4 x 10 sq.mm pvc armoured ltug cable in a trench to be excavated at a depth of 0.75 m putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ sd 196 ] , supplying and fixing of single box type 2 x 20 w led light fitting complete with electronic choke and teakwood round blocks on wall or ceiling with fluorescent tube with pvc unsheathed copper leads from terminals to the fitting. [ twad sor electrical page no ; 173 sl. no : 15b ] , supplying and fixing of 1200mm ( 48 ) sweep ac ceiling fan complete with regulator with 1m down rod including s & f of fan clamp with side plates and cross arm etc, complete as per standard specifications sd 107 , supply and fixing of 300mm ( 12 ) sweep ac exhaust fan complete with necessary wall opening and making good of the wall.etc, complete as per standard specifications. sd 115 , brick lining for 300mm thick in furance roof fibre li 2800l x 900w x 700h in mmning chamber size, door operation : up & down movement manual operated max operating temparature : 700 900 dec celsius. etc, complete. , lpg burner set with lpg bank $ control panel: supply of 4 nos, 5 burner with blower and fully auto control system like 0, 000 kcal capacity lpg fired ignition, flame sensor and auto cut off incorperated in a separate sequencecontoller equivalent to imported contol system for air and lpg with auto igniting system and supply of 20 + 20 cylinder bank with pipeline from lpg cylinder bank up to each burner end by using tata c class grate material pipe with required material etc, complete , 3 hp motor 2no.for use to id fan & 1hp motor use for wet scrubber wet scrubber for gas cleaning system: the system should be enhanced with stainless steel cylinder and ss id fan ( 3hp motor x 2nos. with isi standard ) to avoid rusting, volume of water should be increased for effective scrubbing. , guy supported chimney: this is a cylindrical type ms is 2062 quality, 8mm plate chimney with two coasted of aluminium heat resistance paint exrernally, 7000 mm, long bottom cylindrical chimney. it is rested on 16mm type ms is 2062 qyality ( 100 feet thick base flange and stool flange 16mm thick with 12mm gusset support, cylindrical chimney mounted on foundation 12nos x 25mm dia bolt, nut joints, top 1 cylindrical shell boiler quality 8mm plate x 7000mm long base chimney. it is rested 50mm width base flange & wind forece curtain ms flat set, with lightening arrestor 25mm x 3mm copper flat earthing, with easy hinges type manual opened manhole door, necessary for pollution control boardmonitoringm sample ports arrangment ladder assembly with safety guard set 70 feet full height, one sets of detachable platform, over all size: 800mm dia x 400mm dia x 21000mm length with necessary all arrangements etc., complete , erection, testing and commissioning charges for gasifier etc, complete , supply, delivery, errection, testing and comissioning of 62.50kva generatorwith auto main failiure panel ( amp ) three phase out put voltage 415v consisting of diesel engine capable of delivery continious break gradial fitting water cooled radiclous assessory classes as per standad specificatons pwd sor page no: 146 sl.no; 10a , supply delivery and filling of brick jelly 20mm size with standard specification including cost and conveyance of jelly at site and all labour charges and all other incidential charges etc., complete as per standard specification. , supply delivery and filling of40mm size hbg stone with standard specification including cost and conveyance of jelly at site and all labour charges and all other incidential charges etc., complete as per standard specification. , supply delivery and filling of20mm size hbg stone with standard specification including cost and conveyance of jelly at site and all labour charges and all other incidential charges etc., complete as per standard specification....

Southern Railway - Tamil Nadu

32176251 supply of supply of single pack pu anti corrosive coating paint that can be used as a primer and top coatsupply of single pack pu anti corrosive coating paint that can be used as a primer and top coat,supply of single pack pu anti corrosive coating paint that can be used as a primer and top coat as well as per the specification no.icf/md/spec/357(issue 01 rev:00) which is sprayable and applicable wuth a paint brush. the firm participating in the tender should fulfill the following conditions without which the offer will not be considered.1)the firm should submit their offered product msds and test certificate fulfilling the specification no.icf/md/spec/357(issue 01 rev 00).2)test certificate should be from icf or any other railway production units or rdso or govt.approved nabl or reputed labs from india or abroad. note : one coach set consists of 10 litres (ten litres) of pu anti corrosive paint. sse/paint shop/carriage tamil nadu 160.00 set...

Chennai Petroleum Corporation Limited - Tamil Nadu

31710300 tender for miscellaneous civil and structural works for coke handling system in manali refinery of cpcl miscellaneous civil and structural works for coke handling system in manali refinery of cpcl , earthwork excavation in all types of soil depth up to 1.5 m, including soft or hard murrum, but excluding sofr and hard rock, using mechanical means ( hydraulic excavators ) / manually including clearing away of vegitations, shrubs and debris, cutting and dressing of slides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated / sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated materials within a lead of 100m, as directed including shoring and strutting and providing temporary supports to existing service lines like water pipes, product pipes, sewage pipes, electric overhead and underground cables, cable trenches, etc. all complete as per the specifications and directions of engineer in charge. , same as item no. 10 above, but for depth beyond 1.5m and upto 3.0m. , providing & laying dry rubble soling ( hard core ) with 20 to 40 mm size metal, under foundations / ground floor slab ( grade slab ) , etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors, etc., complete as per drawings, specifications and as per the directions of engineer in charge. , providing, mixing and laying of pcc 1:4:8 nominal mix using 20 mm and downgraded coarse aggregate and using opc ( 53 grade ) for any thickness for all depths below raft, pile cap, etc., including shuttering, tamping, ramming, vibrating, curing, etc., all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete, as per drawings, specifications and as directed by engineer in charge. , providing, mixing and laying in position reinforced cement concrete ( rcc ) of grade m35 with 20mm and down graded coarse aggregates and minimum cement content of 400kg / cu.m as per is 456:2000 using 53 grade ordinary portland cement in sub structure for all depths upto 450mm from ground level along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash, etc. including single pour concreting as specified in drawing, ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m30 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement in super structure for all heights above 450mm from ground level ( upto and inclusive of 20m ) including cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. ( excluding the cost of reinforcement, shuttering ) , etc. all complete as specified, and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m20 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement for grade slab including tamping, screening ( if & as specified in drgs ) to achieve a smooth surface and proper slope without additional finish along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chafering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc. ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing and fixing formwork in sub structure for all depths and height upto 450mm above ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents of approved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , providing and fixing formwork in super structures for all heights above 450mm from ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents ofapproved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500d for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge ( swg ) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in cement mortar 1:4 ( 1 cement:4 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks of class 5.0 in cement mortar 1:6 ( 1 cement:6 m sand ) for all depths including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level, curing, excluding plaster, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincluding mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 20mm thick cement plaster in 2 coats, 1st coat of 12 mm thick in cement mortar 1:4 ( 1 cement : 4 m sand ) & 2nd coat of 8 mm thick in cement mortar 1:4 ( 1 cement : 4 m sand ) plain cement plaster outside / inside the building / boundary wall finished to a smooth finish including providing grooves at junctions of two dis similar materials all complete as directed by eic. , providing 6mm thick cement plaster in cement mortar 1:3 ( 1cement:3 m sand by volume ) on roof ceilings, concrete surfaces including preparation of base, cleaning, chipping, packing of electrical works, scaffolding, finishing, curing, etc. for all heights complete with all labour charges, material costs, tools and tackles, etc. as per specifications and as directed by the engineer in charge. , providing & applying interior paint one coat of emulsion primer & filling services, if any with putty & applying two coats of acrylic distemper paint of asian / approved equivalent make, as per the manufacturer’s specifications including necessary scaffolding, brushing, cleaning & surface preparation with plaster of paris punning, etc. complete as per specifications, drawings and as directed by engineer in charge. , providing and applying textured granular type wall coating of bakelitehylam ltd. or approved equivalent, consisting of twin pack fine gradesilica granules / dry flakes made of special grade of china clay / granite type flakes of heritage or equivalent in approved shade and texture;mixed in situ with 100% acrylic polymer bonding agent; applied overplastered surfaces; the granules / flakes etc., bonding material, mixing, method of application, surface preparation etc. all shall be as per manufacturers recommendations and specifications all complete as directed by engineer in charge. , providing and applying three coats of approved white wash ( comprising of fat lime, water, gum with hot water and sodium chloride with hot water ) in interior surfaces as per the specifications including necessary scaffolding and surface preparation, etc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of premium acrylic emulsion exterior paint of required shade and including surface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty, necessary scaffolding, etc., all complete as per specifications and directions of engineer in charge. , providing and laying water proofing membrane to roof of atacticpoly propylrnr ( app ) with non woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturers specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. ( the thickness of atactic poly propylene ( app ) membrane to be considered as 4.0mm ) , providing and fixing tray type aluminium plank false ceiling consisting of 254 / 305mm x 1264mm or 600mm x 600mm size aluminium planks ( profiled for positive engagement into clip in profiles and demounting of individual planks ) manufactured out of 0.7mm thk. aluminium alloy 3105 / 3005 / 5052 ( as per astm 209m ) with stove enamelled ( coil coated ) finish in approved colour and suspension system consisting of 0.5mm thk. 40mm x 20mm galvnized steel clip in main runner profiles ( @1264m or 600mm as per plank size ) supported by and including 0.5mm thk. 25mm x 16mm gi suspension angle, 1mm thk. 25mm x 34mm x 76mm crca zinc plate steel ceiling brackets ( @ max. 1264mm c / c or 600mm as per profile ) fixed to roof slab / beam, 0.5mm thk. 40mm wide, 105mm high g.i> hold on clamps slotted for level adjustment, perimeter angles including providing slit openings for fixing supply / return air grill, lighting fixtures, ac ducts etc. all complete. , providing and fixing pressed steel door and window frames ofsize ( assorted size out of ) overall 125mm x 60mm section, of required profile confirming to is: 4351, made of 16 swg pressed steel including / consisting of: i ) 3 mm thick ms flat spacers welded to frame @500 mm c / c and at hold fast locations. ( ii ) filling the hollow frame section with concrete. ( iii ) ms angle ( 20mm x 20mm x 3mm ) horizontal tie member below floor furnish ( iv ) ms hold fasts ( 200mm x 25mm x 6mm ) welded to spacers. ( v ) fixing to masonery ( by grouting the holdfasts with m 15 grade concrete in minimum 250mm x 100mm x 100mm sized hole ) / fixing to rcc ( bu minimum 100mm long, 12mm dia metallic counter sunk anchor fasteners ) vi ) ms pad plates ( 40mm x 150mm x 3mm ) & gi mortar gaurd welded to frame at hinge and other hardware locations. vii ) metering of joints between horizontal and vertical members, grinding and smoothening of welding, cleaning of frame surface, finishing ( synthetic enamel painting / electrostatic powder coating / polyurethane ( pu ) coating ) , making true alignements and surface etc. all complete. note: 1 ) cumulative length of all horizontal and vertical frame members shall be measured for payment. frames painted with polyurethane ( pu ) paint coating over epoxy primer. , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40mm overall thickness; and consisting of / including; ( i ) 3 mm thick ms flat all along perimeter ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @ 600 c / c maximum ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces etc. all complete. notes : only the net shutter ( s ) area shall be measured for payment. single shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper ( iv ) ss 304 grade 19mm dia.200 mm long handle on both side of shutter. ( v ) 10mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40mm overall thickness; and consisting of / including; ( i ) 3 mm thick ms flat all along perimeter ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @ 600 c / c maximum ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces etc. all complete. notes : only the net shutter ( s ) area shall be measured for payment. double shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper ( iv ) ss 304 grade 19mm dia.200 mm long handle on both side of shutter. ( v ) 10mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing in position plastic doors ( with door frames ) , of uv stabilized compounds of pvc ( sintex or approved equivalent ) , consisting of 53 x 60mm l shaped door frame ( blr53 of sintex or equivalent ) , 33 x 47mm shutter frame ( dwuf 306 of sintex or equivalent ) , 30mm thick in fill panel slats, complete as per manufacturers specifications and recommendations, including all fittings, fasteners, fixtures, sealing periphery with polymeric sealant etc all complete. , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded build up standard tubular sections / appropriate z sections and other sections of approved make confirming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for galzing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for seperately ) ; for shutters of doors, windows & ventilators made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) including providing and fixing hinges / pivots and making provision for fixing of fittings whereever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) , providing and fixing toughened glass panes of 6.0 mm thickness in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basic item ) , supplying, transporting, storing, fabricating and fixing in position ms steel inserts ( with lugs ) as shown in drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain, reinforced cement concrete members inclusive of adjusting shittering & reinforcement / any other fixture, welding where ever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts, & painting with one shop coat of inorganic zinc silicate primer ( 30 micron dft ) and finishing with two coats of anti corrosive paint ( 20 micron dft each coat ) brand and colour, etc complete as per drawing, specification and direction of engineer in charge. , providing, straightening, fabricating curb angle as per drawing including hold fasts ( ms round or flat ) welded to angles and fixing, painting with one coat of anti corrosive primer complete as per drawings and specifications. , supplying, assembling and installing 1000mm high stin finish stainless steel ( ss 304 grade ) tubular railing of approved design in staircase, ramps, around floor cutouts etc. consisting of :1.50mm dia ss pipe top handrail 2. 32mm dia ss pipe balusters ( at every third step for staircase, @ maximum 1200mm c / c for ramp, floor cutouts ) 3. 3 nos minimum 18mm dia ss pipe intermediate handrails. including: 1. fixing balusters to floor with 4 nos bolts and 8mm thick, 100mm dia ss base plate & ss cap / collar. 2. fixing top hadrail to the balusters with 12mm dia plate. 3. fixing intermediate handrails to the balusters with 12mm dia ss bar connector. 4. all endcaps, decorative caps over balusters, necessary bending, welding, polishing of all weld joints ( lenght of top handrail shall be measured for payment ) . , construction of brick masonery ( brick class 5 ) inspection chambers / manholes of 750mm x 750mm internal size 1000mm deep ( max. ) in cement mortar 1:4 ( 1 cement : 4 sand ) with ci frame and cover 500mm clear dia, ( circular medium duty of grade md 10 ) confirming to is:1726 fixedon rcc slab of m 30 grade, necessary excavation, supplying, fixing 4 nos. 16mm dia m.s. rungs, m 20 grade foundation concrete 1:3 cement mortar ( 1 cement : 3 sand ) plastering of 13mm average thickness for inside & 16mm avg thicness for outside exposed surfaces, backfilling, disposal of surplus earth upto a lead of 100m, benching with m 20 grade cement concrete and rendering smooth with a neat coat of cement slurry, painting the c.i. frame and cover with two coats chlorinated rubber zinc phosphate primer @ 40 dft per coat and finish painting consists of two coats of chlorinated rubber paint @ 40 dft per coat etc. all complete as per drawings, specifications and directions of engineer in charge. , providing and laying upto 600 x 600 mm size coloured glazed ceramic tiles for wall / dado, of approved make & shade including 20mm thick cement bedding c.m. 1:3, pvc beading with matching colour, pointing and finishing exposed joints with white cement / matching colour pigment, etc., including cleaning the finsihed surface with wax polishing complete with material costs, tools and tackles, labour charges as per specifications and as directed by engineer in charge. , providing and laying of permium quality antiskid ceramic floor tiles ( size of all tiles upto 1200 x 1200 ) of approved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement pase / grout mixed with colour pigments matching the shade of tiles, with material costs, tools and tackles, labour charges etc. as per specifications, standards and instructions of engineer in charge. , providing and laying vitrified floor tiles of size upto 1200mm x 1200mm of kajaria / jhonson / somany / orient bell or approved make laid on 20mm thick cement mortar 1:4 ( 1 cement:4 m sand ) including a coating of adhesive as per manufacturers specifications, flush pointing of joints of tiles with cement paste, grouting with white cement and pigment with colour matching the shades of tiles including skirting, finishing, curing, material costs, labour charges, tools and tackles etc. all complete as directed by engineer in charge. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases, etc. using non shrink grout of approved make equivalent including supply of material, roughening surface, cleaning with compressed air / water jets, ramming, curing, labour charges, etc. all complete as directed by engineer in charge. , supplying, transporting, fabricating, erecting and fixing in position as per the specifications, electroforced hot dip galvanised gratings ( gloating weight shall be 305gm / sqm as per is 4759 ) of the approved designed and pattern and erecting & fixing of fabricated steel work on operating floors, platforms, stair landings & treads, drain cover etc., at various levels includingsupply ofall gi fixtures like edge plates for treads, clips, studs, bolts, welding if required and nosing for the treads and etc., complete as per drawings specifications & as directed by engineer in charge , demolishing brick masonry in cement mortar ( taking all necessary safety precautions ) for all depths and heights below and above plinth level including demolition of existing watch tower structural members at all heights, supply of all labours, tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing rcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depth and height below and above plinth level including demolishing of existing foundation upto bottom of pile cap , demolition of existing watch tower structiral members at allheights, supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing pcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depths and heights below and above plinth levelincluding pcc below existing pile cap, including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , providing, hoisting and fixing in position rcc precast elements with reinforced cement concrete grade 1:1.5:3 ( 1 cement:1.5 m sand: 3 graded stone aggregate with opc 53 grade and 20mm & down size graded crushed stone aggregates ) for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks, levelling, aligning and fixing / laying in position using crane, breaking brickwork and / or concrete surfaces and making good the same, etc. all complete ( excluding cost of reinforcement ) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying structural steel conforming to is:2062 grade a, ( yield strength 250.0 n / mm2 ) transporting, storage, straightening, cleaning, fabricating welded / bolted structural steel work in columns, beams, trusses, purlins, platforms, ladders, monorails, staircases, supports, strengthening of steel members, etc. at all locations / levels up to and inclusive of 40.0 m height above hpp / fgl, including supply of bolts, supply of shim plates & approved welding electrodes, including all built up sections / compound sections made out of rolled sectionsand / or plates / bent plates in all types of structural frameworks, floor beams , stairs, or any other structural items or accessories to support equipments, piping , galleries, towers , masts etc, making templates, welding, bolting, erection bolting, splicing, etc. as per specifications and drawing and as directed by the owner / consultant. cutting to required size, straightening / bending if required, edge preparation, cleaing, scrapping and welding, preheating, finishing edges by grinding, fixing in line ans level, including preparing the surface for painting, surface cleaing, wire brushing, removal of mill scale, dust, rust, oil or grease, etc., complete along with providing paint system as follows: ( a ) applying inorganinc zinc silicate coat 50micron dft; ( b ) one coat of epoxy primer paint 50 micron dft each; ( c ) two coat of anti rust epoxy top coat paint 50micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after gritblast cleaing in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , dismantling / modification ofbolted and / or welded structural steel works already erected by others with all cranes and necessary machineries. at all locations and levels upto & inclusive of 50m above hpp / fgl, including all builtup sections / scaffoldingpipes / compound sections made out of rolled sections and / or plates / bent plates in all types of structural frameworks, floor beams, stairs or anyother structural items or accessories to support equipments, piping, conveyor galleries, towers, masts etc., providing temporary staging & bracing and removal of the same after erection and gas cutting, unwelding & bolt removing including supply of all tools & tackles, consumables, necessary scaffolding etc., providing temporary staging & bracing and removal of the same after erection and gas cutting, un welding & bolt removing including supply of all tools and tackles, consumables, necessary scaffolding etc., providing temporary bracings as required, cutting ( by flame or saw ) gusselt plates, bolts, nuts, welding etc., including necessary cranes, skilled & unskilled manpower required for the completing the work. transporting and stacking of all the serviceable materials to designated place and transporting to scrap yard within the refinery premises, all complete at all heights, as specified and directed by engineer in charge , providing and placing / spreading 500 microns thick hdpe sheet / film including laps as per drawing & as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion / contraction / isolation joint filler boards conforming to is:1838 p1 / 1983 in joints including expansion / contraction joints, application of primer as directed by engineer in charge. , same as item no.440 above, but for 25mm thick board. , providing pockets for foundation bolts as per drawings including providing and removing of necessary formwork, etc. complete as per specifications and as directed by owner / consultant. ( for 100 mm x 100 mm to 300mm x 300 size in plan ) and upto 300mm depth , same as item no.460, but for 300mm to 600mm , same as item no.460, but for 600mm and above , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty mechanical anchor fasteners, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item 490 above, but for 20mm dia , same as item 490 above, but for 24mm dia , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty chemical anchor fasteners, packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item 520 above, but for 16mm dia , same as item 520 above, but for 20mm dia , supply and installation of cylindrical triple layer white virgin plastic storage tank of capacity 1000 litres of sintex or approved equivalent on ground floor roof with lid and making necessary cutout / holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly, all complete. including, fixing, transportation to work site all complete as per drawings and directions of engineer in charge. , providing and fixing in position oval shaped coloured glazed vitreous china wash basin 550 x 400 mm of approved equivalent make including c.i. brackets fixed on walls, chromium plated couplings rubber plug with chromium plated chain and chromium plated tap with brass unions, brass c.p. bottle trap with cleaning nut and 32mm dia g.i.waste pipe ( from floor level to nahani trap ) complete with all necessary fittings and put into proper working order as per the specifications, drawings & as directed by engineer in charge. , providing and fixing white glazed earthern ware half stall urinal of parry ware niagara or approved equivalent, including parryware brandor approved equivalent cp urinal push angle valve, cp brass spreader with 32 mm dia pvc pipe, tee, distribution pipe, brackets etc. making inlet & outlet connections fixing with cp brass screws, finishing, etc. all complete as directed by engineer in chagre , providing and fixing in position chromium plated brass liquid soap dispenser of approved quality and design fixed with chromium plated brass screws finished complete as per the drawings, specifications and as directed by engineer in charge. , providing & fixing wall mounted coloured designer type european type wc of approved equivalent with seat cover, p or s traps and low level earthen ware cistern of 10 litres capacity of approved make with chromium plated stop cock & ball cock fittings etc. complete as per drawings, specifications and as directed by engineer in charge. , providing and fixing 150 mm dia. rigid pvc pipes as rain water pipes, weep hole pipes etc. with ms holder clamps including fixing / embedding into masonry / concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg / sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing 15mm dia. nominal bore upvc pipes ( sch 80 ) of ashirvad or approved equivalent including upvc fittings viz. elbows, reducers, couplers, end caps, tees, union, tank nipple, female adapter, male adapter, bends and providing pvc cement and joining with the pipes complete for both open and concealed works including providing ss clamps for fixing in open works and chipping the wall and making good the same after completion of concealed works etc. all complete as per directions of engineer in charge. , same as sl.no. 610 above, but for 20mm dia. nominal bore pipes , same as sl.no. 610 above, but for 25mm dia. nominal bore pipes , same as sl.no. 610 above, but for 40mm dia. nominal bore pipes , same as sl.no. 610 above, but for 80mm dia. nominal bore pipes , same as sl.no. 610 above, but for 100mm dia. nominal bore pipes , supplying and fixing m.s. nozzles with puddle flanges upto 200mm diameter in position as directed with necessary breaking of concrete / brickwork in slabs, beams, walls grouting with non shrinking grout ( if required ) and making the surface good, curing, painting with one coat of anti corrosive primer rtc. complete ( grouting to be paid separately ) . , same as item no. 670, but for 200mm dia to 500mm ms nozzle with puddle flange. , providing and fixing in position under deck insulation consisting of rigid polyisocyanurate foam ( pir ) slabs of size 1000 x 500mm and thickness of 30mm ( covered on one side with glass fibre tissue / aluminium foil having 50mm overlap ) confirming to is:12436 having density not less than 32 kg. / cum., thermal conductivity ( k value ) not more than 0.023 w / mk measured at 10 deg. c; classified as class i for surface spread of flame as per bs 476, part 7; fixed to r.c.c. slab by hot blow grade bitumen of 85 / 25 grade or cold adhesive cprx applied over a coat of bituminous primer @ 0.5 litres / sq.m. applied to bare r.c.c. surface and to the two surface of each pir panel and pressed in position ( while the bitumen is still tacky ) with the help of g.i. screws ( no. 8 x 75mm long ) fixed into rawl plugs ( holes in r.c.c. for the raw plugs shall be drilled prior to applying coat of bituminous primer ) of size 8 x 25mm inserted ( 5 nos. for each slab one each at 4 corners and one at center ) and g.i washers 25mm dia; including covering the overlaps with approved quality sealing compound ( mas 94 or equivalent ) ; chicken wire mesh 24g x 19mm shall then be fixed to g.i screws and tightened with lacing wire; including preparation of surface consisting of cleaning r.c.c surface of all dust, dirt and loose particles by wire brushing; etc. all complete as per approved manufacturers standard specifications and recommendations. , cut or form a hole, square or circular through reinforced concrete floor or wall exceeding 150 mm but not exceeding 500 mm thick & make good complete as directed by owner / consultant, for area of cutting in between 65 and upto 250 sq.cm, all complete as directed by eic. ( for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.700, but for area of cutting in between 260 up to 500 sq.cm. , supplying and applying two coats of coal tar epoxy paint of approved make as per manufactures specifications with minimum of volume solids as 65% coal tar content as 40% pigment content as 22% and dft per coat as 100 microns, on all exposed surfaces of rcc in substructure eg. foundation, footings, rafts, pile caps, beams, slabs, pedastals, trenches, manholes, catchpits, drains, rcc pits, pipe sleepers, equipment / machine foundations etc. all complete for all depths below ground level etc. including all labour, tools and tackles complete as directed by eic. , demolition of existing stores ( 02 nos. ) near wagon loading silos of size approx. 30.1mx10mx6m and 17.78mx7.75mx6m including dismantling of flooring, fixtures, doors, windows, partitions, rolling shutter etc., asbestos sheeting, truss, purlin, structural steel items etc. all complete as directed by engineer in charge. this includes demolishing foundation upto bottom of pile cap and pcc layer underneath if resting on pile else complete foundation including raft and underlying layersis to be demolished in case of open foundation.all unserviceable material should be disposed atvaikkadu area outside the refinery premises up to a lead of 7km as per specifications and as directed by the engineer in charge .all serviceable materials shall be the property of contractor. unserviceable material includes plain cement concrete, reinforced cement concrete excluding reinforcement bars, fire proofing materials, insulations, floor finishes and water proofing layers, bricks, stones, rubbish, vitreous ( ceramic ) sanitary items like washbasin, urinals, water closets and plumbing fittingsetc.serviceable materials are reinforcement steel, structural steel , roof / side cladding sheets, chequered plate, gratings, hand railing, doors, wooden / steel / aluminium windows & ventilators shutters, frames steel / aluminium grills, partitions, steels gates, rolling shutters, etc. as decided by the engineer in charge. , supplyof unskilled labour to carry out petty works not assessable for measurements / minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits and hand tools. , supply of jcb on hire basis on all working days from monday to saturday on 8 hrs. shift including driver, assitant / fuel / oil / lubricants / all consumables etc. complete. the quoted rate should include mobilization, operator crews / driver / assistant cost, labour, tools, tackles etc., as directed by the engineer in charge. , supply of poclain pc 200 on hire basis including fuel / oil / lubricants for excavating the existing compacted earth, levelling to required slopes and dumping at designated places within the site premises. the quoted rate should include mobilization, operator crews / driver cost, loading, transporting, unloading, labour, tools, tackles etc. complete as directed by engineer in charge , providing necessary barricading works with 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3m, embedding the same in firm ground with necessary foundation works, etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works. the same will be the property of contractor....

Municipal Corporation - Tamil Nadu

31705491 attending burst work in 700 mm dia ac pipe water supply pumping main at near oyamari opposite in ward no 8. hire charges for deploying earth moving machinery jcb for earthwork and refilling incluing diesel oil and labour charges etc complete. hire charges for temporary lighting arrangements for burst spot using 150w metal halide light fitting including cost of necessary wiring etc. hire charges for diesel pumpset above 7.5 hp with fuel and crew charges including transportation at site etc. supply and delivery ms specials without inside lining and outside coating but with anti rust painting. lowering of ms 700 mm dia pipes and specials in thetrenches and laying to proper rade andalignment and as directed by as directed by the department officers. interconnecting the 700mm psc pipes with ms pipe on both ends using 700 mm dia ms pipe machineendcollars including cost of ms plates fabrication charges and painting with anti corrosive paints etc. hire charges for 62.5 kva diesel generator....

Chennai Petroleum Corporation Limited - Tamil Nadu

31636740 civil works for construction of silo and other associated civil works for coke handling system in manali refinery of cpcl civil works for construction of silo and other associated civil works for coke handling system in manali refinery of cpcl , supplying, transportation, installing, dismantling and removing of interlocking type temporary steel sheet piles with crane / jcb / poclain / vibro hammer / pile driving machinery of adequate capacity and other ancillary equipment, including driving and joining the sheet piles as per specification up to levels indicated in the drawings & specifications. installed sheet piles are temporary and shall retain the earth, provide excavation support for a depth of 5m from ground level and protection against water seepage & sliding of earth during construction activities, including supply of all materials, steel members, welding, strutting, tie members supporting, labour, plant & machineries, etc. all complete as directed by engineer in charge. ( notes: ( i ) method of measurement for payment will be the actual horizontal limit of temporary sheet piling installed and accepted, and the vertical limit as measured from the bottom of the exposed face of the sheeting to the top of the retained earth behind the sheeting. ( ii ) the steel sheet piles shall be supplied by the contractor and shall remain the property of the contractor ) . , providing necessary barricading works with 1mm thick corrugated gi sheets and supporting with necessary structural steel arrangements including scafffolding pipes and tubes for a maximum height of 3m, embedding the same in firm ground with necessary foundation works, etc. rate quoted should include mobilisation and erection of the above items including demobilisation after completion of works. the same will be the property of contractor. , earthwork excavation in all types of soil depth up to 1.5 m, includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means ( hydraulic excavators ) / manually includingclearing away of vegetations, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated / sub soil water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed includingshoring and strutting and providing temporary supports to existing service lines like water pipes, product pipes, sewage pipes, electric overhead and underground cables, cable trenches, etc. all complete as per the specifications and directions of engineer in charge. , same as item no. 30 above, but for depth beyond 1.50 m and upto 3.0 m. , same as item no. 30 above, but for depth beyond 3.0 m and upto 4.80 m. , transporting & disposing the surplus earthfrom construction area to vaikkadu area up to a lead of 7km including re excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas ( viz., from where the earth is transported and where it is deposited ) to required levels and slopes complete with all lifts as directed by engineer in charge. ( note: if measured by stacks, 30% voids will be deducted. ) , supplying and filling approved m sand of specified quality under raft, foundation, etc. for all depths including the cost of sand, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layers not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and / or other equipment to specified level all complete as per specifications and directions of engineer in charge. , backfilling after execution of work to proper grade and level with selected materials from available excavated soil stacked in soil heaps within a lead of 100 m, including re excavating the deposited soil excavated earlier, breaking clods, laying at all depths & heights in layers of thickness not exceeding 150 mm watering, rolling and ramming by manual methods / mechanical compactors, dressing, trimming, etc., in foundations, plinths, trenches, pits, etc. including all labours, tools & tackles, etc. all complete as per the specifications and directions of engineer in charge. , providing & laying dry rubble soling ( hard core ) with 20 to 40 mm size metal, under foundations / ground floor slab ( grade slab ) , etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors, etc., complete as per drawings, specifications and as per the directions of engineer in charge. , providing, mixing and laying of pcc 1:4:8 nominal mix using 40 mm and downgraded coarse aggregate and using opc ( 53 grade ) for any thickness for all depths below raft, pile cap, etc., including shuttering, tamping, ramming, vibrating, curing, etc., all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete, as per drawings, specifications and as directed by engineer in charge. , providing, mixing and laying in position reinforced cement concrete ( rcc ) of grade m35 with 20mm and down graded coarse aggregates and minimum cement content of 400kg / cu.m as per is 456:2000 using 53 grade ordinary portland cement in sub structure for all depths upto 450mm from ground level along with cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash, etc. including single pour concreting as specified in drawing, ( excluding the cost of reinforcement and shuttering ) , etc. all complete as specified and directed by engineer in charge. , providing, mixing andlaying in position reinforced cement concrete ( rcc ) of grade m30 with 20mm and down graded coarse aggregates and minimum cement content of 330 kg / cu.m; as per is 456:2000 using 53 grade ordinary portland cement in super structure for all heights above 450mm from ground level ( upto and inclusive of 20m ) including cost of admixtures, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. ( excluding the cost of reinforcement, shuttering ) , etc. all complete as specified, and directed by engineer in charge. , same as item no. 120 above, but for height above 20m upto 50m including silo wall concreting , providing and laying reinforced self finished / broomer finish concrete of grade m35 with 40 mm & down size graded stone aggregates and mixing by mechanical mixers for roadwork / pavement in alternate bays, including tamping, compacting by internal and surface vibrators, providing smooth shuttering, providing camber to the surface, providing joints, curing, tarring the sides of slab with hot bitumen, etc. also including applying cement slurry ( 2.75 kg / m2 ) prior to placing concrete, complete as per the drawings and specifications and as directed by the engineer in charge. ( reinforcement shall be paid separately. ) , providing and fixing formwork in sub structure for all depths and height upto 450mm above ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents of approved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. , providing and fixing formwork in sub structure for curved shuttering in foundations in all types for columns, beams, slabs, walls, etc. of buildings for all depths below and upto & inclusive of plinth level, including strutting, bracing, propping, etc., keeping the same in position during concreting and removal of the same after specified period, etc. for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture, etc. all complete and as specified and directed. , providing and fixing formwork in super structures for all heights above 450mm from ground level including steel strutting, bracing, propping, keeping the same in position during concreting and removal of the same after specified period, application of mould releasing agents ofapproved make, for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels or any other fixture, etc., all complete and as specified and directed by engineer in charge. for all works above 450mm and upto 20 m , same as item no. 170 above, but for height above 20 m and upto 50 m , providing and fixing formwork in superstructures for curved shuttering in all types for columns, beams, slabs, walls, etc. of buildings for all heights above plinth level, including strutting, bracing, propping, etc., keeping the same in position during concreting and removal of the same after specified period, etc. for straight / inclined shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture, etc. all complete and as specified and directed. , same as item no. 190 above, but for height above 20m upto 50m , supplying, installing, dismantling and removing slip form shuttering arrangement for construction of rcc silo shell for all elevations from 20 m up to 50 m above gl as per drawings and specifications at all levels, using steel / plywood / wood shuttering. the quoted rate includes providing working platform inside & outside, structural beam / column for erecting slip form arrangements, scaffoldings, jack system, motors, metal ropes, safety nets as per the requirement, winch & lifting arrangement separately for materials and labour movement, all tool & tackles, machineries and materials, etc., all complete as per direction of engineer in charge. , supplying, fabricating and placing in position high strength deformed steel bar reinforcement of grade fe500d for rcc work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractors own 16 standard wire gauge ( swg ) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by engineer in charge. , providing and laying half brick masonry with bricks of class 5.0 in cement mortar 1:4 ( 1 cement : 4m sand ) for all depths and heights including cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by engineer in charge. note: the cost of reinforcement shall be paid seperately under relevant items. , providing and laying brick masonry in super structure with bricks of class 5.0 in cement mortar 1:4 ( 1 cement:4 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in sub structure with bricks of class 5.0 in cement mortar 1:6 ( 1 cement: 6 m sand ) for all depths including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, finishing the joints flush below ground level, curing, excluding plaster, etc. all complete as per specifications, and as directed by engineer in charge. , providing and laying brick masonry in super structure with bricks of class 5.0 in using cement mortar 1:6 ( 1 cement:6 m sand ) for all heights including the cost of materials, labour, tools and tackles, scaffolding / staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size, sealing the gap between masonry and soffit of beam / slab, embedding the fittings, curing, etc. all complete as per specifications, and as directed by engineer in charge. , providing 15mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curingincluding mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 12mm thick cement plaster in cement mortar 1:4 ( 1 cement:4 m sand ) on brickmasonry, pcc / rcc surfaces including preparation of base, cleaning, chipping, packing of electrical, plumbing works, scaffolding if required, finishing, curing including mouldings and providing grooves in plaster, bands, mouldings, etc. as specified for all depths and heights including labour charges, tools and tackles, material costs, etc. as per specifications and as directed by the engineer in charge. , providing 20 mm thick cement plaster in 2 coats, 1st coat of 12 mm thick in cement mortar 1:4 ( 1 cement:4 m sand ) & 2nd coat of 8 mm thick in cement mortar 1:4 ( 1 cement:4 m sand ) plain cement plaster outside / inside the building / boundary wall finished to a smooth finish including providing grooves at junctions of two dissimilar materials all complete as directed by eic. , providing 6mm thick cement plaster in cement mortar 1:3 ( 1cement:3 m sand by volume ) on roof ceilings, concrete surfaces including preparation of base, cleaning, chipping, packing of electrical works, scaffolding, finishing, curing, etc. for all heights complete with all labour charges, material costs, tools and tackles, etc. as per specifications and as directed by the engineer in charge. , providing & applying interior paint one coat of emulsion primer & filling services, if any with putty & applying two coats of acrylic distemper paint of asian / approved equivalent make, as per the manufacturer’s specifications including necessary scaffolding, brushing, cleaning & surface preparation with plaster of paris punning, etc. complete as per specifications, drawings and as directed by engineer in charge. , providing and applying three coats of approved white wash ( comprising of fat lime, water, gum with hot water and sodium chloride with hot water ) in interior surfaces as per the specifications including necessary scaffolding and surface preparation, etc., complete as per specification and as directed by engineer in charge. , supplying and applying two coats of premium acrylic emulsion exterior paint of required shade and including surface preparation, a priming coat with emulsion primer of approved brand as same as final coat including cleaning, removing dust, filling all holes, cracks and depressions with wall putty, necessary scaffolding, etc., all complete as per specifications and directions of engineer in charge. , providing & laying water proofing membrane to roof of atactic polypropylene ( app ) with non woven polyester reinforcement having thin polyethylene foil of approved quality including cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturer’s specifications, rate shall include supplying & sprinkling pea sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by engineer in charge. ( the thickness of atactic polypropylene ( app ) membrane to be considered as 4.0 mm. ) , providing and fixing tray type aluminium plank false ceiling consisting of 254 / 305mm x 1264mm or 600mm x 600mm size aluminium planks ( profiled for positive engagement into clip in profiles and demounting of individual planks ) manufactured out of 0.7mm thk. aluminium alloy 3105 / 3005 / 5052 ( as per astm 209m ) with stove enamelled ( coil coated ) finish in approved colour and suspension system consisting of 0.5mm thk.40mm x 20mm galvanised steel clip in main runner profiles ( @ 1264mm or 600mm as per plank size ) supported by and including 0.5mm thk. 25mm x 16mm gi suspension angle, 1mm thk. 25mm x 34mm x 76mm crca zinc plated steel ceiling brackets ( @ max.1264mm c / c or 600mm as per profile ) fixed to roof slab / beam, 0.5 mm thk. 40mm wide, 105mm high g.i. hold on clamps slotted for level adjustment, perimeter angles including providing slit openings for fixing supply / return air grill, lighting fixtures, ac ducts, etc. all complete. , providing & laying 15mm thick tile acid resistant tiles ( vitrified ) to floors of approved make bedding & joints filled with appropriate acid proof cement. all work complete as per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing & laying acid resistant tiles ( vitrified ) to 10 to 12 mm thick for walls of approved make with applying 2 coats ( to the base concrete ) of mixture of general purpose polymer ( bonding agent ) mixed with opc cement, sprinkling silica to make surface rough. bedding mortar of 8 to 10 mm thickness in 1:3 ratio with 5 % general purpose polymer added to cement. joints of min. width 5 to 8 mm raked, cleaned & filled with appropriate acid proof cement. all work complete as per manufacturer’s specifications, drawing & as directed by engineer in charge. , providing and fixing 2 hours fire rated single shutter steel doors consisting of steel door frame, shutter, vision panel, insulation and hardware such as hinges panic bar, locks / trims for panic bar, door closer, door stopper, consealed flush bolt, etc. including fixing with masonry, partition, etc. all complete as per specificaitons and approved manufacturers details. , providing and fixing pressed steel door and window frames of size ( assorted size out of ) overall 125mm x60mm section, of required profile conforming to is: 4351, made of 16 swg pressed steel including / consisting of: ( i ) 3 mm thick ms flat spacers welded to frame @ 500mmc / c and at holdfast locations. ( ii ) filling the hollow frame section with concrete. ( iii ) ms angle ( 20mmx20mmx3mm ) horizontal tie member below floor finish. ( iv ) ms holdfasts ( 200mmx25mmx6mm ) welded to spacers. ( v ) fixing to masonry ( by grouting the holdfasts with m 15grade concrete in minimum 250mm x 100mm x 100mmsized hole ) / fixing to rcc ( by minimum 100mm long, 12 mm dia metallic counter sunk anchor fasteners ) ( vi ) ms pad plates ( 40mm x150mm x 3mm ) & gi mortar guard welded to frame at hinge and other hardware locations. ( vii ) metering of joints between horizontal and vertical members, grinding and smoothening of welding, cleaning of frame surface, finishing ( synthetic enamel painting / electrostatic powder coating / polyurethane ( pu ) coating ) , making true alignments and surfaces, etc. all complete. notes: ( 1 ) cumulative length of all horizontal and vertical frame members shall be measured for payment. frames painted with polyurethane ( pu ) paint coating over epoxy primer. , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of / including: ( i ) 3 mm thick ms flat all along perimeter. ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap. ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c. ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware, etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c / c maximum. ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces, etc. all complete. notes: only the net shutter ( s ) area shall be measured for payment. single shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16 mm dia 250mm long aldrop on both sides of shutter. ( iii ) spring loaded heavy duty door stopper. ( iv ) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter. ( v ) 10 mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . , providing and fixing pressed steel sheet door shutter made of 18 swg galvanized pressed steel sheet bent to form hollow box of 40 mm overall thickness; and consisting of / including: ( i ) 3 mm thick ms flat all along perimeter. ( ii ) packing the shutter with mineral wool ( 48 kg / cum ) without gap. ( iii ) strengthening with 18 swg gi vertical stiffeners@200 c / c. ( iv ) 3 mm thick ms pad plates welded inside at required locations for fixing of hardware, etc. ( v ) fixing to door frame by 100 mm long ss 304 grade heavy duty ball bearing hinge @600 c / c maximum. ( vi ) hardware and vision panel as required. ( vii ) grinding and smoothening of welding, cleaning, finishing ( synthetic enamel painting / polyurethane ( pu ) coating / electrostatic powder coating ) , making true alignments and surfaces, etc. all complete. notes: only the net shutter ( s ) area shall be measured for payment. double shutter painted with electrostatic powder coating with following hardware: ( i ) over head hydraulic door closer ( heavy duty ) . ( ii ) ss 304 grade 16 mm dia 300mm long aldrop on bothsides of shutter. ( iii ) spring loaded heavy duty door stopper. ( iv ) ss 304 grade 19 mm dia.200 mm long handle on both side of shutter. ( v ) 10 mm dia ss 304 tower bolt ( 250mm long for 2100mm height & 600mm long for 2500mm height ) . ( vi ) 2mm thick 25mmx 25mm gi angles ( vertical ) welded to each shutter at the meeting point of double shutter. , providing and fixing in position plastic doors ( with door frames ) , of uv stabilized compounds of pvc ( sintex or approved equivalent ) , consisting of 53x 60mm l shaped door frame ( blr53 of sintex or equivalent ) , 33x47mm shutter frame ( dwuf 306 of sintex or equivalent ) , 30mm thick infill panel slats, complete as per manufacturers specifications and recommendations, including all fittings, fasteners, fixtures, sealing periphery with polymeric sealant, etc. all complete. , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket, etc. aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p.brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) ; for fixed portion of aluminium doors, windows, ventilators and partitions made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) , providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket, etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p.brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) ; for shutters of doors, windows & ventilators made from powder coated aluminium ( minimum thickness of powder coating 50 micron ) including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) , providing and fixing 12 mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ii, with decorative lamination on both sides, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws, etc. complete as per architectural drawings and directions of engineer in charge. , providing and fixing toughened glass panes of 6.0 mm thickness in aluminium door, window, ventilator shutters and partitions, etc. with epdm rubber / neoprene gasket, etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basic item ) , supplying, transporting, storing, fabricating and fixing in position ms steel inserts ( with lugs ) as shown in drawing including fabrication to any shape made out of flats, plates, rolled sections, sleeves, pipes, etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both plain, reinforced cement concrete members inclusive of adjusting shuttering & reinforcement / any other fixture, welding wherever necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts, & painting with one shop coat of inorganic zinc silicate primer ( 30micron dft ) and finsihing with two coats of anti corrosive paint ( 20micron dft each coat ) on exposed surface only, of approved brand and colour, etc. complete as perdrawing, specification and direction of engineer in charge. , supplying, fabricating, fixing and installation in position at all levels and locations threaded m.s. anchor bolts of all diameters and nomenclature including nuts, washers, anchor plates, washer plates, closure plates, pipe sleeves, etc. in foundations, pedestals, etc. as directed including handling & transporting, straightening if required, turning from relevant size, m.s. rounds to required diameter, threading, welding, providing necessary templates and auxillary dummy structure, if any, necessary tying and welding, providing necessary templates and auxillary dummy structures, if any, necessary tying and welding with reinforcement bars, adjustment of shuttering & reinforcement / any other fixture, greasing exposed metal surfaces, covering bolts and packing the sleeves with jute cloth, etc. all complete as per drawing and specification and direction of engineer in charge. , same as item no.480 above, but for collecting from owner store, fixing and installation in position at all levels and locations ( excluding supply / fabrication which is in owner scope ) , etc. complete. , providing, straightening, fabricating curb angle as per drawing including holdfasts ( ms round or flat ) welded to angles and fixing, painting with one coat of anticorrosive primer complete as per drawings and specifications. , grouting pockets, holes, pipe sleeves of any shape or size, column bases, machine bases, etc. using non shrink grout of approved make equivalent including supply of material, roughening surface, cleaning with compressed air / water jets, ramming, curing, labour charges, etc. all complete as directed by engineer in charge. , demolishing brick masonry in cement mortar ( taking all necessary safety precautions ) for all depths and heights below and above plinth level including supply of all labours, tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing rcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depth and height below and above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning anddisposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , demolishing pcc work ( taking all necessary safety precautions ) manually / by mechanical means for all depths and heights below and above plinth level including supply of all tools and tackles, necessary scaffolding, propping, underpinning, cleaning and disposal of unserviceable material at designated place upto 7 km lead outside the refinery premises ( vaikkadu village ) as per specification and directions of engineer in charge. , supply of unskilled labour to carry out petty works not assessable for measurements / minor repair works, on day to day basis. the rates shall include esi, pf, payroll cost and allowances, fringe benefits, overhead supervision, profits and hand tools. , same as item no.550 above, but for supply of skilled labour. , providing, hoisting and fixing in position rcc precast elements with reinforced cement concrete grade 1:1.5:3 ( 1 cement:1.5 m sand: 3 graded stone aggregate with opc 53 grade and 20mm & down size graded crushed stone aggregates ) for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks, levelling, aligning and fixing / laying in position using crane, breaking brickwork and / or concrete surfaces and making good the same, etc. all complete ( excluding cost of reinforcement ) and as directed by engineer in charge. all material including cementto be supplied by the contractor. , supplying and sealing expansion joints 25mm wide and 12mm deep at all locations and levels in concrete structures with approved two parts liquid polysulphide sealing compound as per is: 12118 including raking of joints, etc. all complete as shown, specified and directed by eic. , supplying and sealing expansion joints 50mm wide and 12mm deep at all locations and levels in concrete structures with approved two parts liquid polysulphide sealing compound as per is: 12118 including raking of joints, etc. all complete as shown, specified and directed by eic. , supplying structural steel conforming to is:2062 grade a, ( yield strength 250.0 n / mm2 ) transporting, storage, straightening, cleaning, fabricating welded / bolted structural steel work in columns, beams, trusses, purlins, platforms, ladders, monorails, staircases, supports, strengthening of steel members, etc. at site to line and level, including supply of bolts, supply of shim plates & approved welding electrodes, including making templates, welding, bolting, erection bolting, splicing, etc. as per specifications and drawing and as directed by the owner / consultant. cutting to required size, straightening / bending if required, edge preparation, cleaing, scrapping and welding, preheating, finishing edges by grinding, fixing in line ans level, including preparing the surface for painting, surface cleaing, wire brushing, removal of mill scale, dust, rust, oil or grease, etc., complete along with providing paint system as follows: ( a ) applying inorganinc zinc silicate coat 50micron dft; ( b ) one coat of epoxy primer paint 50 micron dft each; ( c ) two coat of anti rust epoxy top coat paint 50micron dft each as per manufacturers specifications and as directed by engineer in charge. note: one coat of zinc silicate and one coat of epoxy primer shall be applied on structural steel surfaces after gritblast cleaing in workshop prior to erection as per specifications and as directed by engineer in charge. supply of all materials in contractors scope. , providing and placing / spreading 500 microns thick hdpe sheet / film including laps as per drawing & as directed by engineer in charge. , providing & fixing in position bitumen impregnatedboard 12 mm thk. of approved make premoulded bituminous expansion / contraction / isolation joint filler boards conforming to is:1838 p1 / 1983 in joints including expansion / contraction joints, application of primer as directed by engineer in charge. , same as item no.620 above, but for 25mm thick board. , providing pockets for foundation bolts as per drawings including providing and removing of necessary formwork, etc. complete as per specifications and as directed by owner / consultant. ( for 100 mm x 100 mm to 300 mm x 300 mm size in plan ) and upto 300 mm depth. , same as item no.640, but for depth from 300mm to 600mm. , same as item no.640, but for depth 600mm and above. , supplying, assembling and installing 1000 mm high satin finish stainless steel ( ss 304 grade ) tubular railing of approved design in staircases, ramps, around floor cutouts, etc. consisting of: ( 1 ) . 50mm dia ss pipe top handrail. ( 2 ) . 32 mm dia ss pipe balusters ( at every third step for staircase, @ maximum 1200mm c / c for ramp, floor cutouts ) . ( 3 ) . 3 nos. minimum 18mm dia ss pipe intermediate handrails, including: ( 1 ) . fixing balusters to floor with 4 nos. bolts änd 8mm thick, 100mm dia ss base plate & ss cap / collar. ( 2 ) . fixing top handrail to the balusters with 12mm dia ss bar connector & 6mm thick ss saddle plate. ( 3 ) . fixing intermediate handrails to the balusters with 12mm dia ss bar connector. ( 4 ) . all end caps, decorative caps over balustrades, necessary bending, welding, polishing of all welded joints ( length of top handrail shall be measured for payment ) . , supplying and fixing in position hydrophilic self swelling water stops as per manufacturers specifications in rcc structures at all locations including cutting, fixing and jointing, etc. all complete as shown, specified and directed by eic. , providing and fixing 150 mm dia. rigid pvcpipesas rain water pipes, weep hole pipes etc. with ms holder clamps including fixing / embedding into masonry / concrete, providing connections like shoes, vents, specials, bends, etc. fixing in perfect plumb, etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg / sq.cm including clamps, connections, etc. complete as per specifications and as directed by engineer in charge. , providing and fixing 100 mm dia. rigid pvc pipes with pressure rating of 4 kg / sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring joints using approved lubricant, making hole in the slaband restoring the same to the original condition including provision of cowl in the septic tank vent pipe, etc. complete as per specifications and directions of engineer in charge. , providing and fixing parryware or equivalent approved 15mm nominal bore brass bib cock including breaking walls and making good the same, inlet and outlet connections, etc. complete as directed by engineer in charge. , providing and fixing 15 mm dia. nominal bore upvcpipes ( sch 80 ) of ashirvad or approved equivalent including upvc fittings, viz., elbows, reducers, couplers, end caps, tees, union, tank nipple, female adapter, male adapter, bends and providing pvc cement and joining with the pipes complete for both open and concealed works including providing ss clamps for fixing in open works and chipping the wall and making good the same after completion of concealed works, etc. all complete as per directions of engineer in charge. , same as sl. no. 720 above, but for 20mm dia. nominal bore pipes. , same as sl. no. 720 above, but for 25mm dia. nominal bore pipes. , same as sl. no.720 above, but for 40mm dia. nominal bore pipes. , same as sl. no.720 above, but for 80mm dia. nominal bore pipes. , same as sl. no. 720 above, but for 100mm dia. nominal bore pipes. , providing and fixing in position stainless steel kitchen sink single bowl with drain board glossy finish folded edge of nirali elegance ultra or approved equivalent make of bowl size 510mmx 410mmx 200mm made of min stainless steel sheet supported on m.s. brackets, supply, fixing of m.s.brackets, fasteners, sink cock ( quarter turn range ) of parryware agate or approved equivalent, c.p. angle valve of parry ware, c.p. brass waste, pvc drain pipe with heavy bottle trap of parryware or approved equivalent make, inlet pipe, drain pipe, rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls wherever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing, etc., all complete as directed by engineer in charge. , providing and laying reinforced np3 class ( medium duty ) rcc hume pipe of 300mm dia. with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1cement:2m sand ) for road crossing, etc. including cutting, lowering, laying in position, with proper level, slope, testing of joints, etc. as per specifications and directed by engineer in charge. , same as item no. 790 above, but for 600 mm dia. hume pipe , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty mechanical anchor fasteners, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as per manufacturers specification and directed by engineer in charge. , same as item no.810 above, but for 20mm dia. , same as item no.810 above, but for 24mm dia. , supplying, handling, transporting to site of work and fixing approved electroplated steel heavy duty chemical anchor fasteners, packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia at specified positions on concrete floors, roofs, beams ( sides and bottom ) , walls, columns, etc. according to manufacturers specifications including all accessories like nuts, washers, etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire brush and making good any damage done to the structure, etc. all complete for all heights, depths and locations as manufacturers specification and directed by engineer in charge. , same as item no.840 above, but for 16mm dia. , same as item no.840 above, but for 20mm dia. , supplying and fixing m.s. nozzles with puddle flanges upto 200mm diameter in position as directed with necessary breaking of concrete / brickwork in slabs, beams, walls grouting with non shrinking grout ( if required ) and making the surface good, curing, painting with one coat of anti corrosive primer, etc. complete ( grouting to be paid separately ) . , same as item no.870, but for 200 mm dia to 500mm ms nozzle with puddle flange. , cut or form a hole by chipping, square or circular through reinforced concrete floor or wall for area in between 65 to 250 sq.cm, not exceeding 150mm thick and make good all complete as directed by eic. ( note: for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.890, but for area of cutting in between 260 up to 500 sq.cm. , cut or form a hole, square or circular through reinforced concrete floor or wall exceeding 150 mm but not exceeding 500 mm thick & make good complete as directed by owner / consultant, for area of cutting in between 65 and upto 250 sq.cm, all complete as directed by eic. ( for cutouts, below 65 sq.cm surface area, no extra payment will be made ) , same as item no.910, but for area of cutting in between 260 up to 500 sq.cm. , supplying of 150mm dia gi pipe ( h ) , fabricating, fit up, welding, laying, alligning, including shifting to location & gi painting to the welding portion, etc. complete as per drawing & specification & as per direction of the engineer in charge , same as item no.930, but for 100mm dia. , same as item no.930, but for 75mm dia. , providing, fabrication and fixing g.i. pipe inserts of 40mm dia with fixing arrangement on slab, platforms & silo walls, shown in drawing includingproviding necessary scaffolding, staging, cutting, straightening, if required, embedding in position on both plain, reinforced cement concrete members, fixing to structural steel inclusive of adjusting shuttering & reinforcement / any other fixture, welding where necessary, tying and holding to correct level, line and position, any auxiliary dummy structures to support the heavy inserts all complete as per drawing and specification and direction of engineer in charge. , same as item no.960, but for 25mm dia. , providing and applying two coats of cold applied heavy duty bituminous protective coating over one coat of primer to external faces of underground concrete structures after thorough cleaning of concrete, surface preparation, complete as per drawing and manufacturer specification and as directed by engineer in charge. , providing and fixing dowel bars ( for pavement works alone ) of 25mm dia. x 1000 mm long and at 300 mm c / c including handling, fixing, straightening, cutting, wastage, and g.i. pipe 40 mm dia. x 150 mm long with end cap over dowels at construction joints & fixing cotton filling sleeve & painting for bond broken etc., complete as per drawings, specifications and as directed by eic. , concertina coil fencing: providing and fixing 750mm dia green colour painted razor type concertina fencing with all required clips, pins. etc as per the specifications ( each concertina coil piece stretch to 9m length ) concertina coil shall be fixed to the m.s. angle with 4 rows of same concertina runner wires over existing x type angle supports as per drawings. rate shall be quoted on running metre of compound wall basis. a. diameter of coil: 750mm, number of circles and number of clips are 72 and 180 in each 9m of length. b. central core wire: core wire shall be of 2.6mm diameter made of highcarbon spring steel of high tensile strength having minimum galvanized coating thickness equivalent to 230 grams per sq.m.c. razor strip: 0.5mm thick hot dip galvanized and of width 19mm having series of barbed punched all along the length at regular intervals having minimum galvanized thickness of 12 microns. hardness of tape should be between 137 180 vpn ( victor penetration number ) d. clips: 1.5mm thick made out of stainless steel. e. runner wire: shall be of same specifications as of central core wire. , supply of jcb on hire basis on all working days from monday to saturday on 8 hrs.shift including driver, assitant, fuel, oil, lubricants, all consumable etc. complete. the quoted rate should include mobilization, operator crews, driver, assistant cost, labour, tools & tackles etc., as directed by the engineer in charge. , supply of poclain pc 200 on hire basis including fuel, oil, lubricants for excavating the existing compacted earth, levelling to required slopes and dumping at designated places within the site premises. the quoted rate should include mobilization, operator crews, driver cost, loading, transporting, unloading, labour, tools and tackles etc. complete as directed by engineer in charge. , supply of 20 feet trailer with tractor on hire basis on all working days from monday to saturday on 8 hrs. shift, inclusive of driver, one assitant, all consumables like diesel etc., with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization, operator crews, driver, assistant cost, loading, transporting from site to scrap yard within refinery premises, unloading, labour for loading and unloading, tools, tackles, wire ropes, pulley blocks, belts, chains etc. for lifting, aligning, tying, stacking etc. all complete as directed by engineer in charge. , supply of 12 t hydra on hire basis on all working days from monday to saturday on 8 hrs shift, inclusive of driver, one assitant, all consumables like diesel etc., with all safety precautions within cpcl refinery premises. the quoted rate should include mobilization, operator crews, driver, assitant cost, loading, transporting, unloading, labour, tools and tackles etc. complete as directed by engineer in charge. , dismantling of structural steel works ( bolted / riveted / welded ) of all descriptions ( taking all necessary safety precautions ) for all heights & depth above & below plinth level including supply of all tools & tackles, consumables, necessary scaffolding etc. providing temporary bracings as required, cutting gusset plates, bolts, nuts, weldings etc, stacking of serviceable materials at designated location / cpcl storage yard / scrap yard within the refinery premises as per direction of engineer in charge. , dismantling of scaffolding / staging ( made of pipes / tubes / frames ) already erected by others including at all locations and levels upto 25 mtr from ground level, including all builtup sections / scaffoldingpipes / compound sections made out of rolled sections and / or plates / bentplates in all types of structural frameworks, floor beams, stairs or anyother strucutral items providing temporary staging including supply of all tools and tackles, consumables, necessary scaffolding etc., including necessary cranes, skilled & unskilled manpower required for the completing the work.transporting and stacking of the serviceable materials to designated place, cleaning & disposal of the site of work from all unserviceable materials transporting to scrap yard / disposal yard within the plant boundary, all complete at all depths andheights, as specified and directed by engineer in charge. , providing and fixing double scaffolding system on the exterior side, upto 25 mtr height from groud level made with 40mm dia m.s. tube 1.5m centre horizontal & vertical tubes joining with cup & lock system with m.s.tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it inserviceable condition for the required duration as approved and removingit there after.the scaffolding system shall be stiffened with bracings, runners, connection with the buildings / strucutures etc. whereverrequired for inspection of work at required locations with essential safety features for the workmen etc.complete as per directions and approval of engineer in charge. the elevational area of the scaffolding and product of height shall be measured for payment purpose. the payment will be made once irrespective of duration of scaffolding. ( scaffolding material shall remains property of contractor and shall be taken back bycontractor after completion of work / instructions of eic ) ...

Integral Coach Factory - Tamil Nadu

30926748 supply of supply and application of anti corrosive paintsupply and application of anti corrosive paint,supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for sr ilanka main line passenger coaches1) bogie frame arrangement to drg.no.685 03 001 alt b 2nos 2) bogie bolster arrangement to drg.no.685 04 001 alt a 2nos. sl. no.(1) & (2) together constitute one coach set....

Southern Railway - Tamil Nadu

29589141 supply and apply of single pack pu anti corrosive paint on fiat and icf bogie components in different quantities at central workshop, golden rock, southern railway, trichy 620 004supply and apply of single pack pu anti corrosive paint on fiat and icf bogie components in different quantities at central workshop, golden rock, southern railway, trichy 620 004, ...

Southern Railway - Tamil Nadu

28040597 supply of supply and apply of single pack pu anti corrosive paint on fiat and icf bogie components in different quantities at central workshops, golden rock, southern railway, tiruchirappalli 620 004supply and apply of single pack pu anti corrosive paint on fiat and icf bogie components in different quantities at central workshops, golden rock, southern railway, tiruchirappalli 620 004,...

Integral Coach Factory - Tamil Nadu

26130050 supply of , supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for srilanka main line passenger coaches 1) bogie frame arrangement to drg.no.685 03 001 alt b 2nos 2) bogie bolster arrangement to drg.no.685 04 001 alt a 2nos. sl. no.(1) & (2) together constitute one coach set....

Southern Railway - Tamil Nadu

26075255 supply of , mcb double pole fitted in a metal enclosure (box) with the following specifications: 1) capacity of mcb: 16amps 2) type: double pole (single pole and neutral) 3) enclosure: metal box with anti corrosive paint 4) with four fixing screws for metal box cover fixing with metal box base 5) with four fixing screws for metal box rear for fixing to the wall 6) with suitable hole in the metal box bottom for cable entry. 7) with suitable cut in the metal box in such a way that the mcb should be operated without opening the metal box cover. 8) mcb make: l&t/ havells/ crabtree/ c&s/ abb/ siemens/ standard make only with isi marking 9.) warranty: minimum 1 year guarantee/warranty certificate to be submitted at the time of supply...

Integral Coach Factory - Tamil Nadu

25369322 supply of , supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for srilanka main line passenger coaches 1) bogie frame arrangement to drg.no.685 03 001 alt b 2nos 2) bogie bolster arrangement to drg.no.685 04 001 alt a 2nos. sl. no.(1) & (2) together constitute one coach set....

Southern Railway - Tamil Nadu

24778608 supply and apply of anti corrosive paint on fiat and icf bogie components in different quantities at central workshop/southern railway/ponmalai/tiruchchirappalli 620 004...

Southern Railway - Tamil Nadu

24429934 supply of , ready mixed anti corrosive paint, brushing, bituminous, black, acid, alkali, water and chlorine resisting to is:9862 :2017 (first revision)...

Integral Coach Factory - Tamil Nadu

23498152 supply of supply and application of anti corrosive paint, supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for srilanka main line passenger coaches 1) bogie framearrangement to drg.no.685 03 001 alt b 2nos 2) bogie boslter arrangement to drg.no.685 04 001 alt a 2nos. sl. no.(1) & (2) together constitute one coachset....

Ministry Of Micro Small And Meduim Enterprises - Tamil Nadu

23123664 supply of cable and conductor testing machines equipment 15 nos for electrical lab: smoke density tester for cable testing, halogen acid gas tester for cable testing, multicell ageing oven, thermal stability test apparatus for cable testing, cold chamber for cable testing, fixture for cold impact test apparatus ( low temperature impact apparatus ) for cable testing, torsion testing machine ( wrapping test ) for cable testing, ss tank with anti corrosive paint for cable testing, step up transformer with digital ac voltmeter & ammeter for output ( horizontal type dimmerstat model ) , wheatstone bridge ( dual type wheatstone cum kelvin double bridge preferred ) ) , 5000 ampere capacity copper flexible ( silk woven or laminated shim type ) shunt with ( crimped ) solid square copper end plates in four numbers...

Indian Oil Corporation Limited - Tamil Nadu

22987768 carrying out repainting of truss or purlin structurals , sprinkler line , qb line , lpg lines , air lines in empty cylinder shed cum cylinder filling shed with anti corrosive paint at indane bottling plant , chengalpet carrying out repainting of truss or purlin structurals , sprinkler line , qb line , lpg lines , air lines in empty cylinder shed cum cylinder filling shed with anti corrosive paint at indane bottling plant , chengalpet...

Southern Railway - Tamil Nadu

22804193 supply of mcb double pole ., mcb double pole fitted in a metal enclosure (box) with the following specifications: 1) capacity of mcb: 06amps 2) type: double pole (single pole and neutral) 3) enclosure: metal box with anti corrosive paint 4) with four fixing screws for metal box cover fixing with metal box base 5) with four fixing screws for metal box rear for fixing to the wall 6) with suitable hole in the metal box bottom for cable entry. 7)with suitable cut in the metal box in such a way that the mcb should be operated without opening the metal box cover. 8) mcb make: l&t/ havells/ crabtree/ c&s/ abb/ siemens/ standard make only with isi marking 9) warranty: minimum 1 year guarantee/warranty certificate to be submitted at the time of supply...

Southern Railway - Tamil Nadu

22688074 supply of mcb double pole., mcb double pole fitted in a metal enclosure (box) with the following specifications: 1) capacity of mcb: 16amps 2) type: double pole (single pole and neutral) 3) enclosure: metal box with anti corrosive paint 4) with four fixing screws for metal box cover fixing with metal box base 5) with four fixing screws for metal box rear for fixing to the wall 6) with suitable hole in the metal box bottom for cable entry. 7) with suitable cut in the metal box in such a way that the mcb should be operated without opening the metal box cover. 8) mcb make: l&t/ havells/ crabtree/ c&s/ abb/ siemens/ standard make only with isi marking 9.) warranty: minimum 1 year guarantee/warranty certificate to be submitted at the time of supply...

Southern Railway - Tamil Nadu

22479090 supply of paints for ashok leyland, paints for ashok leyland lorry to the following in set. one set consists of : 1.paint enamel taxi yellow oy72 asian or nerolac, qty : 10 ltrs. 2.paint enamel white asian or nerolac, qty : 6 ltrs. 3.paint enamel black asian or nerolac, qty : 4 ltrs. 4. anti corrosive paint black , qty : 6 ltrs. 5.nc putty for enamel paint, qty : 12 kgs. 6. nc thinner for enamel paints, qty : 5 ltrs....

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

22203803 tender for casting of 4 , 100 nos of 8 . 00 m ( 140kg wl ) psc poles as per rec design drawing at thalaivasal psc yard , casting of 8 . 00m ( 140kg wl ) psc poles as per rec design cast in m42 design mix ( rcc 1:1 . 14:2 . 33 ) using ordinary portland cement of 53 grade , 4mm hts wire , 10mm & 12mm machine crushed metal of 50% each ( hbg stone jelly ) and river sand ( sieved ) using the twin mould form boxes including cost of labour charges , for cleaning and fixing of form boxes , stretching and tensioning of hts wires , mixing and conveying and placing of concrete , vibrating , curing in bed for three days ( not less than 72 hours ) , casting and testing of cubes of size 15x15x15cm for ascertaining the strength of concrete for detensioning , cutting of hts wire , removing of bolts & nuts , shifting of poles to the curing tanks for curing and after curing stacking in platform after levelling the stacking yard , painting at top & bottom using anti corrosive paint , cleaning the curing tank and yard including cost of wedge , barrels , bolts , nuts , empty gunnies for covering the poles in bed for 3days , welding electrodes , waste oil , hydraulic jacks , tensioning machines , welding plants , water charges , pvc hose , properly insulated cables for welding and power supply and necessary t&ps for maintaining the yard , testing of poles for its quality for acceptance of supply including cost of keeping the form boxes in proper shape including cost of all materials used , lead , lift etc . , complete at thalaivasal psc yard ....

Southern Railway - Tamil Nadu

21872140 supply of supply and application of anti corrosive, supply and application of anti corrosive painting in under frame to specn. icf/md spec. 357 issue status 01 rev.00 as per the scope of work enclosed. (material : anti corrosive paint per coach : 34 ltrs.)...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

21650151 overhauling , servicing of d . m . plant unit , servicing and overhauling of d . m . plant : 1 . opening of pressure filter , cleaning the pebbles , washing the sand media and fixing up the vessel after painting inside the black anti corrosive paint . 2 . opening of sac unit , cleaning of blocking nozzles giving acid treatment for the existing resins . back washing and removing the powdered resin and charging the new resin . 3 . opening of sba unit , cleaning of blocking nozzles , treating the resin with brine solution , removing the powered resin and replacing with new resin . 4 . the above works are to be under taken with your own manpower and tools . 5 . resin washing has to be carried out with your technical persons . 6 . after servicing of d . m . plant the water treated has to confirm the parameters i . e . tds below 100 . ...

Tamil Nadu Cooperative Sugar Federation Limited - Tamil Nadu

21567949 overhauling , servicing of d . m . plant unit , servicing and overhauling of d . m . plant : 1 . opening of pressure filter , cleaning the pebbles , washing the sand media and fixing up the vessel after painting inside the black anti corrosive paint . 2 . opening of sac unit , cleaning of blocking nozzles giving acid treatment for the existing resins . back washing and removing the powdered resin and charging the new resin . 3 . opening of sba unit , cleaning of blocking nozzles , treating the resin with brine solution , removing the powered resin and replacing with new resin . 4 . the above works are to be under taken with your own manpower and tools . 5 . resin washing has to be carried out with your technical persons . 6 . after servicing of d . m . plant the water treated has to confirm the parameters i . e . tds below 100 . ...

Integral Coach Factory - Tamil Nadu

21551527 supply of supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for srilanka, supply and application of anti corrosive paint to spec icf/md/spec 357 issue status 01 rev 00 for srilanka main line passenger coaches 1) bogie framearrangement to drg.no.685 03 001 alt b 2nos 2) bogie boslter arrangement to drg.no.685 04 001 alt a 2nos. sl. no.(1) & (2) together constitute one coachset....

Indian Railway - Tamil Nadu

18049062 tender for set of anti corrosive paints 1.single pack high performance grafted co polymer based anti corrosive protective coating of brand anticor sk 03 orequilant, qty 15 ltrs, 2. single pack zinc primer anti corrosive primer, qty 15 ltrs....

Integral Coach Factory - Tamil Nadu

17821084 tender for supply and application of anti corrosive paint on one coach setconsisting of 1)bogie frame assembly to drg.no. 45503001 col.i alt g 2 nos. 2)fiatbogie bolster to drg.no.45504001 alt e 2 nos or similar type of one coach set ofbogie frame and bogie bolsters. 3) dry film thickness (dft)of the paint shall be 150micron for above sl.no.1&2. special condition : 1. time lag between shot blasting andpainting should not be more than 30 minutes in any case. 2. material safety datasheet (msds) to be given along with the paints supplied. 3. supply rates andapplication rates to be quoted separately. 4. annexure a to be followed....

Indian Railway - Tamil Nadu

17805319 tender for set of anti corrosive paints 1.single pack high performance grafted co polymer based anti corrosive protective coating of brand anticor sk 03 orequilant, qty 15 ltrs, 2. single pack zinc primer anti corrosive primer, qty 15 ltrs....

Indian Oil Corporation Limited - Tamil Nadu

16594620 carrying out repainting of truss / purlin structurals in all sheds, conveyors, stair cases, sprinkler and qb air pipeline with anti corrosive paint as per scope of work and name writing of all sheds as per look book at indane bottling plant, chengalpet...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

8729428 supply of the following materials to sub store /kodayar/papanasam/periyar for the use at all the power houses of this generation circle for aoh 2016 17 work 1).aluminium paint with paste 2).anti corrosive paint [black] 3).red oxide paint note: a).to be supplied in 5 ltrs pack b). any branded items...

Southern Railway - Tamil Nadu

5827648 supply of mild steel u shaped clamps for hoiding core of pole mounted battery charger, provided with grey colour anti corrosive paint coat as per enclosed drawing no: bc/001/03/2013. (one set includes 2 nos of bottom clamps +2 nos of top clamps)....

Southern Railway - Tamil Nadu

5362411 tirunelveli â?? tenkasi (bg) section anti corrosive paints to the rail in main line and all loop lines in between ten â?? tsi stations in sse/p.way/tirunelveli and sengottai section for a length of 70km...