Town Panchayats - Tamil Nadu

40855273 tender for rejuvenation of bund to ayyan kulam in ammapettai town panchayat.; 1 earth work excavation for foundation, septic tank etc., in all soil sand sub soils ( vide sl no.506+62 ) and to full depth as may be directed except in hard rock requiring blasting inclusive of stoning, shuttering, bailing out water wherever necessary refilling the foundation with excavated earth other than sandy soil in layers of not more than 15cm thick well rammed and depositing the surplus earth with in the compound in place shown by the departmental officers within an initial lead and lift and clearing and leveling the site etc., completed 2 foundation 3 plain cement concrete 1:4:8 ( one cement , four m sand , eight aggregate ) mix using 40mm iss hbg stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15 cm thick and well rammed and compacted , etc., completed complying with standard specification. 4 centering for soffits of rcc slabs of plane surface like lintels, beams , etc., including strutting 3m high using mild steel sheets of size 90cm x60cm x and b.g 10 stiffened with m.s angles of size 25mm x 25mm x 3mm laid over silver oak ( c.w ) joists of size 10cm x 6.5cm ( spaced at about 90cm c / c ) and supported dy casurina props of 10cm to 13cm dia ( spaced of 75cm c / c ) complying with standard specification and directedgrade beam 5 with strutting 6 plain cement concrete 1:2:4 ( one cement, two fine aggregates and four coarse aggregates ) using 20mm size iss hbg metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification 7 earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete with extra lead for conveyance etc, complete. 8 providing and laying, spreading and compacting graded stone aggregate to wet mix macadam ( wmm ) specification including premixing the material with water at omc in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of morth specifications. 9 supplying and laying rubberised interlocking paver blockm40 grade providing and laying of63mmthick high strength type conforming is 15658 2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40n / mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approvednon skitting surface in the top and the rate including levelling the base preparation ofpavers as sub base, stone dust cushion 150mm thick layingout of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification, . 10 supplying and fixing gi.pipe 32mm dia ( b class ) including cutting and fixing in suitable concrete and providing weld mesh of size 750 x500mm size 90 gauge and providing m.s. flat 35x6mm size at middle angle allowed of sizeluding cost and conveyance and welding with weld mesh. 25x25x5mm including cost and conveyance and welding with weld mesh. 11 supply and installationof led based street light luminaire made up of extured alluminium alloy body sealed toughened glass protector and pc side covers. the optical and control gear compartment should be with ip66 tightness leds in natural white ( 4000 4 ) 25w led street light 12 supply and fixing of 2x 1.5 sq.mm copper cable from pole switching point to light fittings 13 supply and fixing of light post 4m length single bracket pole with base plate ( 250 x 250 x 6mm ) 76.10mm od x 3.65mm thick x 4000mm length including fiber connection junction box internal wiring works on each pole including cost and conveyance etc complete. 14 collection, supply and filling of stone dust of approved quarry including cost and conveyance of al materials to site and all labour charges for filling etc complete. 15 providing and laying in position, standardised concrete mix m 20 grade in accordance with is:456 2000, using 20mm and down graded hard broken granite stone jelly for all rcc items of works with minimum cement content of 325 kg / m? and maximum water cement ratio of 0.55, including admixture ( plasticiser / super plasticiser ) in recommended proportions as per is:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about ( 5 cu.m. ) 7730 kg. of 20mm machine crushed stone jelly and with about ( 3.3 cu.m. ) 5156 kg. of 10 12mm machine crushed stone jelly and with about ( 4.79 cu.m. ) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.the coarse and fine aggregates to be used should comply with the requirements of is standards. ( no separate payment will be made by the department for the excess usage of materials ) . 16 suppling and fabricating and placing in position ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors. including charges for cutting, straightening, and bending, typing, welding, jointing, over laping and all labour charges etc....

Town Panchayats - Tamil Nadu

40846700 providing park ward no.12, sf.no.46 / 6 gandhi nagar in panamarathupatty town panchayat; 1 conducting geophysical survey, quality and quanty test and transportation charges etc., including labour charges in the field rent of the vechile for reaching the palce,rent of the instrument and excluding charges for the geologist etc., complete as per standard specifications 2 supply and delivery of 200mm dia pvc plain casing pipe (cs)including cost and conveyance of materials and labour charges etc., : note: approximate length of pipe is given the length may be decided as per site conditions during drilling of borewell etc., complete as per standard specifications 3 drilling 150 mmdiaborewellin hard rock areas anywhere in the state inculding transportation to site of work in hardrock areas inculding labour charges for insertion of ms casing pipe and flushing of borewell and for minutes. ( as per md twad board chennai letter no : f15090/ae/cm/twad/2013/ dated:22/4/2013 ) 4 0m to 150m 5 151m to 180m 6 181m to 210m 7 211m to 240m 8 241m to 270m 9 supplying and fixing in position of the following pvc / g.i pipes and specials best approved quality conforming to iss and providing leak proof joint with pvc adhesive etc.,complete complying with standard specification. 10 5.00 hp submersible motor 75 lpm x 225m head 11 5.00 hp pannel board 12 4.00 sqmm 3core copper cable 13 50mm upvc pipe 14 40mm g.i b class pipe 15 40mm g.iheavy coupling 16 40mm gun metal gate valve 17 2000 lit hdpe tank 18 kisok box 19 160mm pvc borewell dummy 20 borewell pipe ms clamp 21 labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable withproper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of tpicn switches starter, voltmeter, ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per ie rules etc., complete and testing the pumpset and trail run for 10 days. 5.00 hp submersible motor 22 supply and run of 4 x 6 sq.mm.(56nos/0.3mm.dia) pvc insulated single core unsheathed copper conductor cable of 1100 v on 7/20 g.i. bearer wire for service connection mains (sd 68) 23 supply and run of 4 x 4 sq.mm(84/0.3) pvc insulated sc unsheathed cu.conductor of 1100v grade in 25mm dia g.i pipe (bclass) suitable bend at both ends with necessary angle iron up right and end supports for mains.sd 73) 24 lowering pvc rigid/ hdpe pipes and specials to trench and laying to proper grade and alignment jointing with pvc couplers with cement paste and testing to the required pressure including conveyance of water for filling during testing etc.,complete 25 refilling with excavated earth after laying the pipes into the trencheswell rammed and compactedthe surplus earth over the pipeline trench including leveling the site complete complying with standard specifications includingall labour charges etc., complete as per standard specifications. 26 earth work excavation for foundation in all types of soils and sub soils to full depth (such as soils in rock / silt / light black cotton soil / ordinary soil ) except in rock requiring blasting but inclusive of shoring, shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth other than sand in layers of 150 mm thick well rammed and consolidated, depositing the surplus earth in places shown by the departmental officers with initial lead of 10 m and initial lift of 2 m. complete as per tnss23 & 24, v, vi (s2), vii, 9,10 27 footing 28 plinth beam 29 plain cement concrete of mix 1 : 4 : 8 (one part cement, four part sand & eight part of aggregates) using 40mm gauge hard broken metal from approved quarry including all cost, conveyance of materials to site with proper mixing, compacting, finishing and curing etc., complete as per standard specification. tndss no: 28 v, vi (s2) v,vi (s5a) vii 30 supplying anderrecting centeringfor sides and soffits including necessary supports and strutting upto3.29mt height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia supported at not more than 75cm centre to centre etccompletecomplying with standard specification without strutting.tnss no or nbc no 30(s) 86 86 a v, vi(s3)vii 31 plinth beam 32 for column 33 plain cement concrete 1:2:4 mix (one part cement, two part sand and four part of aggrigate) using 20 mm size iss hbg metal from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing. laying and curing etc. complete. complying with std. specifications. 34 reinforced cement concrete 1:1½:3 mix (one part cement, one and half part m sand and three part of aggregate)using 20mm size iss hbg metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc.complete with std.specifications.(using vibrator)tndss no: 30 v, vi (s3), vii 3. 35 suppling and fabricating and placing in position ms(or) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors as per standard specification. 36 brick work in cement mortor 1:5 mix (one cement, five sand ) using new best countrybricks of size 8 ¾”x 4 ¼”x 2 ¾”from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. 37 plastering in cement mortor 1:5 mix (one cement, five m sand) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. 38 supply and fixing of m.s grills for compound wall with doors and windows with one coat of red oxide with primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. 39 painting the new walls with exterior emulsion paint two coats with good quality of approved emulsion paintcomplete in all floorscomplying with standard specification.( the colour and shade of the paint shall be got approved by thedepartmental officers.) 40 painting two coats over the new iron work using ready mixed enamel paint including cost of all materials to site and all labour charges for mixing applying etc., complete as per standard specifications 41 providing and laying, spreading and compacting graded stone aggregates to wet mix macadam 250mm thick specification including premixing the materials with water at omc in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in sub base/ base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc.,complete as per clause 406 of morth 42 supplying and laying precast designer paver block confirming to is 1568 2006 specification manufacturing and laying standard of m40 grade 63mm thick (table clauses 5 and 9.14) suitable for bus terminals industrial complexes road on expensive soils etc., including the cost of paver block of size 225mm x 12.50 mm x 80mm and conveyance of materials to work site mentioned in the tender schedule cost of loading and unloading handling during over sand bed of 150mm thick (excluding the cost of sand) conveyance paver block cutter to site and hire charges of vibrators and block cutter operator and labour for leveling the sand to paver block etc., complete isi 15658 2006. 43 providing single seater double polish finish blackgranitesitting single round bench ( stool type) 100 thick 45cm dia granite slab for bench slab and 150mm dia on middile and 30cm on end posts including cost and conveyance and fixing in position etc., complete 44 supply and installation of led based street light luminaire made up of extured alluminium alloy body sealed toughened glass protector and pc side covers. the optical and control gear compartment should be with ip66 tightness. leds in natural white (4000 4) 45 supply and fixing of 2 x1.5 sq mm copper cable from pole switching point to light fittings etc., complete 46 supply and fixing of light post 4.00 m length with gradually reduce type pole 3 stages using 75mm and 50mm and 25mm size and bent up to top edge led including fiber connection junction box internal wiring works on each pole inculuding cost and conveyance etc.., complete 47 providing various designs of animal dust bins made of 3 layer fiber structure with multi colour powder coating. the height of the dist bins 4 feet available models are penguin, rabbit, fish and monkey etc.,complete 48 supplying and fixing of four seater seesaw to a height of 0.50m with 80mm dia leaver and 40mm top bar with ms pipes. the seatr is of moulded plastic with heavy duty bush bearing.the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the dpeartmetal officers 49 supplying and fixing ofdouble swing of height 2.40m height with 40mm dia ms pipes support as legs and top bar is 50mm dia.the seat is 9mm thick reinforced rubber with antiskid chequred top with heavy ball bearing and the suspension is 7mm dia electro galvanized chain and the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the departmental officers 50 supplying and fixing of jungle gym the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the dpeartmetal officers 51 supplying and fixing of slide for below 12 years old childrens to a length of 3.00 m with 80mm dia leaver and 40mm top bar with ms pipes. the seater is of moulded plastic. the ladder frme is made up of 25mm m.s. ppe., handrail 20mm dia ms pipe and the centre support is 80mm dia ms pipes.the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the departmental officers. ...

Vedanta - Tamil Nadu

40830012 auction sale of residual aluminium small size – (pcb required) residual mixture (pcb required) miscellaneous aluminium items aluminium alloy clamp (holders) high chrome valves and current measurement instruments ( alloy) rectifier, coolers, ac cooler and radiators cu radiators rectifier, coolers, ac cooler and radiators al radiators wood hydrate calcined alumina decomposer scale semi processed material rubber and polymer ( frp+hdpe+pvc +poly urethane + other related) furniture material xrd and related components ( spectrum), ms material ( pipe and tank) & gi sheet dorr gearbox pumps and valves motors foundry roof electrical ( dorr and foundry ) & instrument material aluminium cable copper cable cladding sheet al...

Town Panchayats - Tamil Nadu

40822707 providing park ward no.12, sf.no.46 / 6 gandhi nagar in panamarathupatty town panchayat , conducting geophysical survey, quality and quanty test and transportation charges etc., including labour charges in the field rent of the vechile for reaching the palce, rent of the instrument and excluding charges for the geologist etc., complete as per standard specifications , supply and delivery of 200mm dia pvc plain casing pipe ( cs ) including cost and conveyance of materials and labour charges etc., : note: approximate length of pipe is given the length may be decided as per site conditions during drilling of borewell etc., complete as per standard specifications , drilling 150 mmdiaborewellin hard rock areas anywhere in the state inculding transportation to site of work in hardrock areas inculding labour charges for insertion of ms casing pipe and flushing of borewell and for minutes. ( as per md twad board chennai letter no : f15090 / ae / cm / twad / 2013 / dated:22 / 4 / 2013 ) , 0m to 150m , 151m to 180m , 181m to 210m , 211m to 240m , 241m to 270m , supplying and fixing in position of the following pvc / g.i pipes and specials best approved quality conforming to iss and providing leak proof joint with pvc adhesive etc., complete complying with standard specification. , 5.00 hp submersible motor 75 lpm x 225m head , 5.00 hp pannel board , 4.00 sqmm 3core copper cable , 50mm upvc pipe , 40mm g.i b class pipe , 40mm g.iheavy coupling , 40mm gun metal gate valve , 2000 lit hdpe tank , kisok box , 160mm pvc borewell dummy , borewell pipe ms clamp , labour charges for the erection of submersible pumpset in borewell / openwell including fixing and jointing submersible cable withproper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of tpicn switches starter, voltmeter, ammeter, three pilot ( indicating ) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per ie rules etc., complete and testing the pumpset and trail run for 10 days. 5.00 hp submersible motor , supply and run of 4 x 6 sq.mm. ( 56nos / 0.3mm.dia ) pvc insulated single core unsheathed copper conductor cable of 1100 v on 7 / 20 g.i. bearer wire for service connection mains ( sd 68 ) , supply and run of 4 x 4 sq.mm ( 84 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade in 25mm dia g.i pipe ( bclass ) suitable bend at both ends with necessary angle iron up right and end supports for mains.sd 73 ) , lowering pvc rigid / hdpe pipes and specials to trench and laying to proper grade and alignment jointing with pvc couplers with cement paste and testing to the required pressure including conveyance of water for filling during testing etc., complete , refilling with excavated earth after laying the pipes into the trencheswell rammed and compactedthe surplus earth over the pipeline trench including leveling the site complete complying with standard specifications includingall labour charges etc., complete as per standard specifications. , earth work excavation for foundation in all types of soils and sub soils to full depth ( such as soils in rock / silt / light black cotton soil / ordinary soil ) except in rock requiring blasting but inclusive of shoring, shuttering and bailing out water wherever necessary and refilling the sides of foundation with excavated earth other than sand in layers of 150 mm thick well rammed and consolidated, depositing the surplus earth in places shown by the departmental officers with initial lead of 10 m and initial lift of 2 m. complete as per tnss23 & 24, v, vi ( s2 ) , vii, 9, 10 , footing , plinth beam , plain cement concrete of mix 1 : 4 : 8 ( one part cement, four part sand & eight part of aggregates ) using 40mm gauge hard broken metal from approved quarry including all cost, conveyance of materials to site with proper mixing, compacting, finishing and curing etc., complete as per standard specification. tndss no: 28 v, vi ( s2 ) v, vi ( s5a ) vii , supplying anderrecting centeringfor sides and soffits including necessary supports and strutting upto3.29mt height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90mm x60mm and 10bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia supported at not more than 75cm centre to centre etccompletecomplying with standard specification without strutting.tnss no or nbc no 30 ( s ) 86 86 a v, vi ( s3 ) vii , plinth beam , for column , plain cement concrete 1:2:4 mix ( one part cement, two part sand and four part of aggrigate ) using 20 mm size iss hbg metal from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing. laying and curing etc. complete. complying with std. specifications. , reinforced cement concrete 1:1½:3 mix ( one part cement, one and half part m sand and three part of aggregate ) using 20mm size iss hbg metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc.complete with std.specifications. ( using vibrator ) tndss no: 30 v, vi ( s3 ) , vii 3. , suppling and fabricating and placing in position ms ( or ) r.t.s. bar for reinforcement to all rcc works as per the design given including cost ofsteel and binding wire also in all floors as per standard specification. , brick work in cement mortor 1:5 mix ( one cement, five sand ) using new best countrybricks of size 8 ¾”x 4 ¼”x 2 ¾”from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. , plastering in cement mortor 1:5 mix ( one cement, five m sand ) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. , supply and fixing of m.s grills for compound wall with doors and windows with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specification. , painting the new walls with exterior emulsion paint two coats with good quality of approved emulsion paintcomplete in all floorscomplying with standard specification. ( the colour and shade of the paint shall be got approved by thedepartmental officers. ) , painting two coats over the new iron work using ready mixed enamel paint including cost of all materials to site and all labour charges for mixing applying etc., complete as per standard specifications , providing and laying, spreading and compacting graded stone aggregates to wet mix macadam 250mm thick specification including premixing the materials with water at omc in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in sub base / base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of morth , supplying and laying precast designer paver block confirming to is 1568 2006 specification manufacturing and laying standard of m40 grade 63mm thick ( table clauses 5 and 9.14 ) suitable for bus terminals industrial complexes road on expensive soils etc., including the cost of paver block of size 225mm x 12.50 mm x 80mm and conveyance of materials to work site mentioned in the tender schedule cost of loading and unloading handling during over sand bed of 150mm thick ( excluding the cost of sand ) conveyance paver block cutter to site and hire charges of vibrators and block cutter operator and labour for leveling the sand to paver block etc., complete isi 15658 2006. , providing single seater double polish finish blackgranitesitting single round bench ( stool type ) 100 thick 45cm dia granite slab for bench slab and 150mm dia on middile and 30cm on end posts including cost and conveyance and fixing in position etc., complete , supply and installation of led based street light luminaire made up of extured alluminium alloy body sealed toughened glass protector and pc side covers. the optical and control gear compartment should be with ip66 tightness. leds in natural white ( 4000 4 ) , supply and fixing of 2 x1.5 sq mm copper cable from pole switching point to light fittings etc., complete , supply and fixing of light post 4.00 m length with gradually reduce type pole 3 stages using 75mm and 50mm and 25mm size and bent up to top edge led including fiber connection junction box internal wiring works on each pole inculuding cost and conveyance etc.., complete , providing various designs of animal dust bins made of 3 layer fiber structure with multi colour powder coating. the height of the dist bins 4 feet available models are penguin, rabbit, fish and monkey etc., complete , supplying and fixing of four seater seesaw to a height of 0.50m with 80mm dia leaver and 40mm top bar with ms pipes. the seatr is of moulded plastic with heavy duty bush bearing.the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the dpeartmetal officers , supplying and fixing ofdouble swing of height 2.40m height with 40mm dia ms pipes support as legs and top bar is 50mm dia.the seat is 9mm thick reinforced rubber with antiskid chequred top with heavy ball bearing and the suspension is 7mm dia electro galvanized chain and the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the departmental officers , supplying and fixing of jungle gym the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the dpeartmetal officers , supplying and fixing of slide for below 12 years old childrens to a length of 3.00 m with 80mm dia leaver and 40mm top bar with ms pipes. the seater is of moulded plastic. the ladder frme is made up of 25mm m.s. ppe., handrail 20mm dia ms pipe and the centre support is 80mm dia ms pipes.the cost shall inclusive of all materials, labours and fixing etc., complete as directed by the departmental officers....

Southern Railway - Tamil Nadu

40791085 supply of barrel tower boltbarrel tower bolt, barrel tower bolt ( aluminium alloy ) dia 10mm x 100 mm long icf / std 5 6 011, alt. c / 0 item 19 to is:204 / 92, pt.2, type 4, table 1, amendment no.3 of jan.08 ( reaffirmed 2012 ) . [ warranty period: 30 months after the date of delivery ] => limited...

Military Engineer Services - Tamil Nadu

40783386 tender for repairs to pcc roads, hardstanding and road furniture at technical area cvrde, avadi.; 1 repair topotholesanydepthn.exc1sqm eachincludingsweepingfreefromdustandmudorwaterscoringsunkensurfacesinroadpathmakinggoodbyapplyingtackcoatbituminousprimer@ 5 kg per10 sqmputtingin premixasspecifiedforbituminouscarpet ( 2cmthick ) wellrammedand sealedwithpremixedsandsealcoat ( 6.80kg binder with 0.06 cumofsand ) againwellrammed. complete all as specified and as directed 2 preparing surfaces of black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed 3 m&lonblacktopsurfacesandapplyingevenly apriming / tackcoatwithbituminousprimer @ 5kg per x sqminpavingbitumenasspecifiedand directed .complete all as specified and as directed 4 m&lfor bitmuminous premix semi dense asphaltic concrete, 30mm consolidated thickness with 5.5% of binder content by weight of total mix and compacted to reqd camber and gardient with mechanical paver complete all as specified andasdirected . 5 m&l for providing hot applied thermoplastic compound 2.5mm thick and providing selecting glass beads @ 250gm per sqm as per irc 135, finished and existing old surface of painting lines dashes, arrows, letters etc.on roads / concrete exe10cm wideto be leveled uniform and free from streaks and holes including cleaning of surface to remove a loose dirt etc; complete all as specified. and as directed. 6 demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and asdirected by engineer in charge. 7 m&lfor sand filling under floors or in foundation including watering and consolidation complete all as specified and asdirected by engineer in charge. 8 m&l for layingpolythene film, black, 50 micron laid in floors complete all as specified and as directed by engineer in charge. 9 m&l for pavement quality cement concrete ( pqc ) work in pavement / hard standing of flexural strength 40 kg / per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less including necessary steel formwork complete all as specified and asdirected by engineer in charge. 10 m &l for forming 12mm thick machine cut expansion filled with premormed bituminious filler and top 30mm primed and sealed with sealing compound grade b for concrete slab 150mm thick complete all as specified and as directed by engineer in charge. 11 m&l for forming dummy joint 65mm deep x 10mm wide of machine cut filled with sealing compound grade b complete all as specified and as directed by engineer in charge. 12 finishing surfaces of concrete road by machine brooming on concrete surfaces while concrete is in green position all as specified andas directed by engineer in charge. 13 painting lines dashes, arrows, letters etc.on concrete roads surfaces with ( two or more coats ) of concrete floor paint to give uniform finish with road marking paint of superior make as approved by the engineer in charge, i / c cleaning the surface of oil dirt, scales, oil, grease and other foreign material etc. and lining out complete all as specified and asdirected. 14 m&l for cement concrete type b 1, 1:2:4 ( using 20 mm graded stone aggregate ) asinsub base complete all as specified andas directed. 15 m&l for machine pressed coloured precast with grey cement and pigment conctete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness, m 35 grade over a layer of 25mm thick sand cushion complete allas specifed andasdirected. 16 m&l for hydraulic pressed chequered cement concrete colour tiles 300mmx300mmx 25mm, set, jointedand pointed in thick neat cement slurry in floors and pointed with white cements and pigments iincluding screed bed or bedding layer of cement mortar 15mm thick for laying floor finishes with cm 1:6complete all as specified and as directed 17 demolition of brickwork or stone / boulder masonry or cement block masonary, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified andas directed by engineer in charge. 18 m&lforbrick work with sub class b brickes straight or curved on plan exc 6m mean radius in plan built in cm 1:6 complete all as specified andas directed 19 m&l for rendering 15mm thick in fair faces of brick work or concrete surfaces in cm 1:4 finished even and smooth with out using extra cementcomplete all as specified andasdirected. 20 m&lforpre cast cement concrete type c1 1:3:6 block masonary with solid blocks exe 10cm in width and setting in cement mortar 1:6 complete incld necessry excavationembedding blockin the ground to depths directed , required andtempering around and removing surplus spoil to a distance not exc 50 mtr and deposting where directed all as specified and as directed by engineer in charge. 21 s&f in repairs rubber speed bump of size 50 mm ( height ) x 375 mm ( width ) x 500 mm ( length ) , abs block black and yellow & reflectors on both sides including necessary fixing arrangements with epoxy / thermoplastic adhesive and anchor bolts all as per manufacturers instructions and complying to guidelines issued by min of road transport etc. complete and as per direction of engineer in charge.make:cateye / darkeye / suneyez / 3m 22 manufacturing, supplying and fixing cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm of retro reflective sign boards made up of 3 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type iv of astm d 4956 01 in blue and silver white or other colour combination including subject matter, message ( bi lingual ) , symbols and borders etc. as per irc ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class 2 of astm d 4956 01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c / c to back support frame of m.s. angle iron of size 35x35x5 mm along with theft resistant measures, mounted and fixed with 2 nos. m.s. angles of size 35x35x5 mm to a vertical post made up to m.s.tee section ismt 65x65x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including embedding in pcc 1:2:4 ( 300x300x750mm ) type b1including removal of excavated soil to a distance not exc 50 m and making holes in pipes, angles flats, providing & fixing m.s. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer ( vertical ms tee support to be painted in black and white colours ) .backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of engineer in charge.note: demolition of cement concrete in concrete road surface for making holes to be paid separately 23 m & l for preparation of new / old concrete kerb stone surfaces / plastered surface and applying two or more coats of first quality retro reflective enamel paint onkerb stone, etc to give uniform finish of any colours over a coat of primer and pattern complete all as specified andas directed by engr in chargemake : berger guidline / dulux trade line / indigo 24 s&f in repairs road convex safety mirror outdoor type made of one piece of polycarbonate traffic mirror unbreakable round wide angle of size 80 cms dia, outdoor type, including mountedsteel frame along with ms pole supporting of varying height including all fixing arrangementswith adjustable brackets and nuts bolts for installation, suitable for driveways, garages, warehouses and buildings blind spots and necessary foundations including excavation & removal of soil ( 300mmx 300mm x 450 mm with m15 using 20mm graded stone aggregate ) complete all as specified and as directed.make:cateye / darkeye / suneyez / 3m 25 supply only calcium hypo chlorite granules packing size ne less than 45kg , 65 95 concentration complete all as specifed and directed....

Military Engineer Services - Tamil Nadu

40773911 tender for special repairs to certain building at kattabomman under ge tirunelveli ( tender id:2023_mes_629434 _1 ) ; 1 dismantling corrugated or semi corrugated asbestos cement sheets in roof covering, all as specified and directed. 2 supply and fixing pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. 3 supply and fixing prepainted galvalume aluminium zinc coating gi based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof, fixed with self tapping screws complete all as specified and directed. 4 material and labour for 610mm dia aluminium 0.50mm thick turbo ventilators with 47 vanes including frp / aluminium base plate fixing with galvalume roof sheet including necessary fixing arrangements complete all as specified and directed. 5 material and labour for 25mm thick plain cement concrete type b 1, 1:2:4 ( using 20mm graded aggregate ) as in floorcomplete all as specified and directed. 6 material and labour for providing colour non skid joint free ceramictiles 7 to 8mm thick square / rectangular, area of each tile exceeding 0.18 sqm but to exc 0.38 sqm in floor of approved quality and patternset , and jointed in neat cement slurryand pointed in coloured cement to match in floors over 15mm thick screed bed in cm 1:6 complete all as specified and directed. 7 material and labour for non skid ceramic colouredtiles7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc., setand jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including screed bed or bedding layer of mortar 15 mm thick in cm 1:6 complete all as specified and directed. 8 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 9 material and labour for colour non skid joint free ceramictiles 7 to 8mm thick square / rectangular polished , on vertical surfaces such as skirting dado riser to steps , setand jointed in neat cement slurryand pointed in coloured cement to match in floors over 10mm thick backing coat in cm 1:4. complete all as specified and directed. 10 material and labour for 50mm thick plain cement concrete type b 1, 1:2:4 ( using 20mm graded aggregate ) as in floorcomplete all as specified and directed. 11 supply and fixglass dividing strips 38 x 3mm thick complete all as specified and directed. 12 demolition of reinforced cement concrete of roofs, floors ( other than ground floors ) , beams, staircases, landings, chajjas and similar suspended work complete all as specified and as directed . 13 material and labour for rcc 1:2:4 ( nominal mix ) type b1 ( using 20mm graded stone aggregate ) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies deck slab and shelves and the like complete all as specified and directed. 14 material and labour for formwork to soffits of suspended slabs such as landings, shelves and similar work : not exceeding 200mm thick ( horizontal or sloping ) for rough finished surfaces of concrete complete all as specified and directed. 15 material and labour for tmt bars 10mm dia and over cut to length bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and bindingwith and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 16 material and labour pcc 1:3:6 typec120 mmgraded aggregate 75 mm thick in plinth protection finished even and fair without using extra cement complete all as specified and directed. 17 material and labour pcc 1:3:6 typec120 mmgraded aggregate in surface channel and drain complete all as specified and directed. 18 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms moulds , mitred stopped ends etc complete all as specified and directed. 19 taking down cement plaster on brick or stone wallincluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 20 material and labour for rendering 10mm thick on brick or concrete surfaces in cm 1:6 on fair faces of brick work or concrete surfaces of wall finished even and smooth ( without using extra cement ) complete all as specified and as directed. 21 material and labour rendering 15mm thick in cm 1:4 on o fair faces of brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. 22 demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins arches, pillars etcall as specified and as directed. 23 material and labour for brick work with fly ash bricks straight or curved on plan exec 6 mtr mean radius with cement mortar 1: 6. complete all as specified and directed. 24 material and labour preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 2mm thick wall care putty on wall complete all as specified and directed. 25 material and labour preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces complete all as specified and directed. 26 material and labourfor complete removal of existing treatment andapplying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces complete all as specified and directed. 27 material and labourfor complete removal of existing treatment and applying two coats of oil bound distemper over a coat of alkali resistant primer over 2mm thick wall care putty on wall complete all as specified and directed. 28 material and labour for preparation of old plasteredsurfaces & applying two coat of white wash on ceilings complete all as specified and as directed.. 29 material and labour for preparation of old steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and as directed. 30 taking down shutters exceeding 1.0 sqm and not exceeding 2 sqm and removing from site complete all as specified and directed.. 31 material and labour flush door shutters, 35mm thick, solid core construction, withboth faces is covered with decorative face veneer with lipping / frame to match and glazed vision panels of size 20 cm x 20 cm, including lipping complete all as specified and as directed. ( note glass shall be measured and paid separately ) 32 material and labour for french polishing on surfaces of any description width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed. 33 material and labour for hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 34 supply and fix 4.0mm thick plain sheet glass of ordinary quality and glazing with oil putty n exc 0.5 sqm fixed to steel framing complete all as specified and as directed. 35 supply and fixing butt hinges heavy weight cold rolled mild steel and fixed in 125mm long complete all as specified and directed. 36 supply and fixing in repair butt hinges heavy weight cold rolled mild steel and fixed in 125mm long complete all as specified and directed. 37 supplying and fixing aluminium anodised barrel tower bolts of extruded section 150 mm and fixed complete all as specified and directed. 38 supplying and fixing extruded aluminiumhandles fabricatedtype anodised 150mm long complete all as specified and directed. 39 material and labour for aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections ( 250 mm length ) complete all as specified and directed. 40 supply and fixing in repairs door closer aluminium extruded section body hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. 41 dismantling wrought iron or mild steel work of any description complete all as specified and directed. 42 material and labour for welded steel wire fabric not exc 4 kgs / sqm supplied and fixed complete to wood or steel members complete all as specified and directed. 43 material and labour for framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 complete all as specified and directed. 44 dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. 45 supply and fixing steel rolling shutters 1.25mm thick , with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, completegear operated type with bevel gear box and crank handle complete all as specified and as directed. 46 supply onlyball bearing wheelfor the rolling shutter complete all as directed by engineer in charge. 47 supply onlysafety lever locks mild steel with 4 levers for the rolling shutter complete all as directed by engineer in charge. 48 material and labour for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 49 dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover filletscomplete all as specified and as directed. 50 material and labour gl frame work for seamless ceiling comprising of gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with gl cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having knurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. hangers 6 mm dia. g.i. ( upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 51 material and labour for 8mm thick seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish ( frame work for ceiling shall be measured and paid separately ) finished with 2mm thick putty over calcium silicate board and two coats oil bound distemper over a coat of primer complete all as specified and directed. 52 schedule of credit amount brought back from ser page no. 29 rs. 54, 404.00 will be deducted from the above quoted amount to derive the contract sum.signature of contractor...

Southern Railway - Tamil Nadu

40752333 supply of aluminium trolley step ladderaluminium trolley step ladder,aluminium trolley step ladder confirming to is 3696 (part 2): 1991 or latest version as per the following parameters .1) platform height 14 feet. 2) railing height 2 feet. 3) maximum load capacity 200 kg. 4) wheels : 4 nos of swivel wheels made of polyurethane with brake. 5) basement mild steel frame. 6) platform aluminium slip resistant platform. 7) hand rail available. 8) back frame aluminium /aluminium alloy. 9) aluminium platform size range: 18 feet x18 feet to 24 feet x24 feet. 10) warranty minimum 12 months from the date of delivery. [ warranty period: 12 months after the date of delivery ] => limited...

Southern Railway - Tamil Nadu

40739632 supply of aluminium alloy pneumatic impact wrenchaluminium alloy pneumatic impact wrench,aluminium alloy pneumatic impact wrench size 3/4 inch, torque: 653 nm(min.), operating pressure: 6.3 bar(min.), weight: 2.3 kg(max.), air consumption: 8 18 cfm(min.), warranty: 01 year, make: stanley/de neers/groz/chicago only [ warranty period: 12 months after the date of delivery ]...

Military Engineer Services - Tamil Nadu

40656614 tender for repairs to road in vellachi under age ( i ) navy chennai ( tender id: 2023_mes_628160_1 ) 82580 / e8; 2 material and labour for preparing of existing black top surfaces of roadby brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc., complete all as specified and as directed by engineer in charge. 3 repairs to pot holes any depth, not exceeding 1.5 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting arround edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming ( including of road metal ) by applying tack coat with bituminous primer at 5kg per 10 sqm, putting in premix as specified for thin bituminous carpet ( 2 cm thick ) well rammed and sealed with premixed sand seal coat 9.8 kg of binder with 0.09 cu m of sandstone chippings, 6.3 mmsize, again well rammed ( including supply of premix binder and sand ) depth of potholes n exc 30 mm complete all as specified and as directed by engineer in charge. 4 material and labour for appying evenly a priming / tack coat with bitumen primer using paving bitumen ( vg 30 ) at 5 kg per 10 sqm complete all as specified and directed 5 material and labour for bituminous premix semi dense asphaltic concrete ( sdac ) , 30 mm consolidated thickness with 5.5 % binder content of paving bitumen by weight of total mix usingvg 30 grade bitumen, rolled and compacted to required camber and gradient complete using mechanical paver and rolled using power roller 8 to 12 tonne capacity complete all as specified and directed.note: the contractors quoted rates shall also be deemed to include the following element: ( i ) in case of variation in the binder content as per approved design mix in comparison with the binder content as specified above, the variation in qty of binder content on lesser side shall be adjusted through supply only rate of bitumen vg 30. however, variation on the upper side shall be carried out by the contractor without any price adjustment. 6 m & l for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to bs 3262 1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. 7 material and labour for solar road stud having 3 leds of colours red / yellow to a side ( total 6 nos ) housed in a tough pressure die casted aluminium alloy of any size ( 120 x 130 mm ) , ( 100x130mm ) and ( 125x125mm ) of height 20 mm with built in stem nail 30 mmx 50 mm long for fixing with epoxy. leds, solar cells, battery & light sensor well protected in side under tough unbreakable polycarbonate transparent sheet roof. system workable for 2 3 days ( nights ) after full charge in 8 10 hours. make:greenlite cat part no. gpl 03 01 or equivalent as mentioned in ps 8 signature of contractor...

Military Engineer Services - Tamil Nadu

40655789 tender for maintenance and repairs to road at tuticorin under ge ( i ) cg chennai; 1 m&l for repairs to pot holes of any depth and n. exc. 1 sq.m. eachincluding sweeping free from dust and mud or water, scoring sunken surface in roads, cutting around edges to atleast 25mm in depth making good by applying tack coat @ ( 5 kg / 10 sq.m. putting in premixed bituminous macadam, well rammed and sealed with binder @ 9.8 kg / 10 sq.m. blinded with 0.09 cum of stone chippings 6.3mm size and again well rammed, depth of pot holes exc. 30mm including supply of premixed macadam, binder and chippingscomplete all as specified and as directed by the engineer in charge. 2 material and labour for premix bituminous, macadamwith 4.0% binder content by weight of total mixusing paving bitumen , any penetration of viscocity vg 30 , laid / rolled and compacted to required gradient and camber complete all as specified and as directed. 3 material and labour for preparingblack top surfaces of road by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and as directed. 4 material and labour applying evenly a priming / tack coat with bituminous primer using paving bitumen of viscocity vg 10 atthe rate of 4 kg per 10 sqm over black top surfacecomplete all as specified and as directed. 5 material and labour forbituminous premixsemi dense asphaltic concrete using hot mix plant40mm thick consolidated thickness with 5.5% binder content by weight of total mix usingpaving bitumen of viscocity vg 30, levelled, rolled wtih 8 to 12 tonne tandem vibratory roller and compacted to required camber and gradient using mechanical paver complete all as specified and as directed. note:the binder content is indicated tentatively and shall be as per acutal mix design.the rate of bitumen for adjustment purpose shall be as per the rate in purchase voucher. 6 material and labour for road marking strips, lines , dashes arrows, zebra crossings , letters etc of 2.5mm thick ( reflective type ) on new surfaces of road / pavementsand the likeexceeding 10 cm wide with hot thermo plast material @5 kg / sqm of white or golden yellow by applying with fully automatic paint applicator machine , fitted with profile shoe, glass beads dispenser by providing drop on glass beads @ 0.25 kg / sqm applying with propane tank heaters and profile shoe heater etc driven by the skilled opearator on road surface complete all as per morth specificationscomplete all as specified and as directed. 7 s&f for solar road stud having 3 leds of colours red / yellow to a side ( total 6 nos ) housed in a tough pressure die casted aluminum alloy housing of size 130x120mm of height 20 mm with built in stem nail 30 mmx 50 mm long for fixing with epoxy. leds, solar cells, battery & light sensor well protected in side under tough unbreakable polvcarbonate transparent sheet roof. system workable for 2 3 days ( nights ) after full @ & 1600 each charge in 8 10 hours.make: greenlite cat part no. gpl 03 01 srs bn ( dual directional ) or equivlaent in dark eye / 3 m....

Town Panchayats - Tamil Nadu

40611263 providing high mast light ( 16m ) at ward no:5 harur main road ambethkar ground in kadathur town panchayat; construction of foundation work with earthwork excavation , pcc :1:4:8, centering for shuttering, steel reinforcement, rcc 1:1.5:3including tower bolt rods for pole fixing including cutting, threading and welding work, refillingincluding all leads and lifts rtc, , complete , drawing an as directed by the departmental engineers supply of 16mtr high mast complete as per standard specificationbottom 8.3mtrs, top 8.3mtrs, bottom dia 460mm, top dia 150mm 16 withmeter high mast system octagonal post, fixing head frame with canopy , movable lantern carriage, three drum winch, 1hp motor hoisting ropes, with standing upto50mts / sec with fabrication with totally hot dip galvanize special steel plates suitable for 50 mts / sec wind velocity, fixing head frame, as specified in the relevantiss and with three abase and as directed by the dept. officerstreet light luminaries in aluminum alloy ( anodized ) construction suitable for led including control gear lighting source: led light. lumens:110lm / w operating voliage:230v ac, power consumption: 150 watts cooling technical: thermal conductivity aluminum column shape not easy to accumulate dust simple structure & reliable operation temperature: 22 to 55 0 c. ip grading : ip65, product life:> 50000 hrs, light color : 6300 k ( dependent adjustments ) , integrated sure protection , anti uv optical cover coating and increase hardness power supply driver: ac power 180 v 270 v , all fasteners: ss grade 304supply and fixing of ring 8 nos light round arm sewage weld steel tubular round bracket with made of 50mm “b” class pipe and also providing 8” round plate including cost and conveyance as per standard specificationsupply and run of 4 x 6 sq.mm. ( 84 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v on 7 / 20 gi bearer wire for service connection mainssupply and fixing of 230v ac 50hz flexible cable with pole 5x2.5sq.mm 1100v 6sq.mm with two core cable and connection with polesupply and fixng of tneb meter board suitable for 1 phases 63a service connection in fabricated powder coated sheet metal box made up of suitable angle iron frame work of size 2 feet x 1 1 / 2 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on eb pole covered with hylem sheet of size 2 feet x 1 / 2 feet of 6mm thickness with necessary ms clamp sets, bolts and nuts and supply and fixing of 3 nos 63a fuse units ( 500v ) 1 no. neutral link, copper earth flat of size 1 x 1 / 4 with inter connection of eb meter to fuse units by 7 / 16 pvc insulated copper wire with earth connection complete.supply of control panel suitable control circuit for the operation of the mast , it shall also consist of suitable control for the power contactor with , dual timer with 32 a 4 pole contactor 2 nos with enclose supply and fixing of 230v auto time controlmcb with kitkate fuse erection and commissioning of 16mtr high mast with help of suitable equipments civil work towards labour charges for erection of pole. fixing of 8noswith led lightsupply and fixing of earthingand lighting arrester as per the isi specification with an earth electrode of 2.10 metre class b gi pipe of dia not less than40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements withnecessary masonry work and with 38mm rcc cover slab for the brick masonry and lighting arrester and name board arrangementetc completed...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

40595833 tender for disposal of condemned and scrap materials available at sub stores / p.velur and central stores / nedc / namakkal.; 1 lot no .1 ( lot ofone item ) condemned 22kv distributiontransformer of various capacity w / o oil ( copper wound ) =25 nos 2 lot no .2 ( lot of one item ) condemned 22 kv distributiontransformer various capacity w / o oil ( copper wound ) =25 nos 3 lot no .3 ( lot o f oneitem ) condemned 22 kv distributiontransformer of various capacity w / o oil ( copper wound ) =25 nos 4 lot no .4 ( lot of one item ) condemned 22 kv distributiontransformer of various capacity w / o oil ( copper wound ) =25 nos 5 lot no .5 ( lot of three items ) 1.condemned 22 kv distributiontransformer of various capacity w / o oil ( copper wound ) =21. nos2.condemned distribution transformer 63kva / 11kv w / o oil ( aluminium wound ) =7 nos3.condemned distribution transformer 100kva / 11kv w / o oil ( aluminium wound ) =1 no 6 lot no .6 ( lot of sixteen items ) 1 .m.s miscellaneous iron scrap = 25582 kg2. transformer lamination sheet scrap =2199 kg3. t & p scrap 67kg4. condemned fire extinguishers =10 nos 5. condemned wall coffer = 5 nos 6. condemned weighing balance various capacity ( 1000 kg & 50kg ) =2 nos 7. auto parts scrap =99 kg8. empty barrel 40 / 45 gallon leaky = 51 nos 9. radiator scrap = 1no 10. tube light fitting scrap =33 kg11 . cond.ceiling fan with regulator = 4 nos 12. rail cut bits scrap = 5221 kg13. ms / rts scrap= 4003 kg14. rsj cut bit scrap= 3139 kg15. slater weighing scale 50 kg capacity =1no16.lt ab switch= 10nos 7 lot no .7 ( lot of one item ) 1. acsr scrap = 53740 kgs 8 lot no .8 ( lot of six items ) 1. alu ug cable scrap =737 kg2. aac cut bits scrap = 3909 kg3. aaac scrap= 1275 kg4. alu transformer winding scrap with insulation paper oil soaked = 431 kg5. pvcalu cablescrap = 47 kg6. all aluminium alloy scrap = 13 kg 9 lot no .9 ( lot of twenty three items ) 1. brass scrap = 182 kg2. cond.tong tester = 6 nos3. cond.ltct coil = 9 nos4. cond.volt meter = 1 no5. cond.megger = 4 nos6. cond.cmri meter = 4 nos7. cond.monitor = 40 nos8. cond.computer assecceries = 600 kg9. cond.pedestal fan = 2 nos10. cond.relay of various sizes =7 nos11. cond.hand held device = 66 nos12. cond.ups = 20 nos13. cond.sv / mv lamp fittings = 23 nos14. cond.2kva ups for computer = 11 nos15. cond.phase sequence meter sizes = 1 no16. cond.earth tester = 1 no17. cond.digital clamp meter =1 no18. coil ltct 400 / 5a electr rescring ( new ) = 705 nos19. coil ltct 800 / 5a electr rescring ( new ) = 105 nos20. lt ct coil 150 / 5a ( new ) = 793 nos21. 3 ph 100 120a meter ( sh ) = 2 nos22. cond. type writer =1 no23. gps instrument hand held old version ( new ) = 2 nos 10 lot no .10 ( lot of seven items ) 1. waste paper scrap= 2712kg2. deal wood scrap= 191kg3. pvcscrap = 7 kg4. metering box pilfer proof 2 compartments ( fiber ) = 217 nos5. hut service kit with bulb =646 set6. empty wooden drum ( available at p.velur sub stores ) = 400 nos7. teak wood scrap= 121kg 11 lot no .11 ( lot of three items ) 1. mechanical meter scrap= 9815kg2. hq meter scrap =10538kg3. static meter scrap = 13397kg 12 lot no .12 ( lot of one item ) 1 condemned metering set various sizes w / o oil = 40nos 13 lot no .13 ( lot of one item ) 1 condemmned metering set various sizesw / o oil= 43 nos 14 lot no .14 ( lot of four items ) 1. condemned metering set various sizes w / o oil = 14 nos 2. condemned 110kv ct w / o oil =2 nos 3 condemned 33 / 11 kv ctw / o oil =6 nos 4 condemned 22 kv ctw / o oil= 30 nos 15 lot no .15 ( lot of two items ) 1. condemned station battery =30 nos2. condemned 12v tubular battery =24 nos...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

40579052 disposal of scrap and condemned materials available at cedc north coimbatore , lot no.1(lot of two items) 1. scrap rail cut bits 6155 kgs 2. scrap rsj cut bit 3916 kgs , lot no.2(lot of fourteen items) 1. scrap miscellaneous iron 7750 kgs 2. scrap gi 534 kgs 3. scrap transformer lamination sheet 98 kgs 4. cond. fire extinguisher 1 no 5. cond. monitor 7 nos 6. cond. printer 5 nos 7. cond. water filter 1 no 8. cond. chair (computer) 9 nos 9. scrap ms misc scrap 80 kgs 10. scrap gi wire 310 kgs 11. cond. laser printer 1 no 12. scrap auto parts 13 kgs 13. empty steel drum above 6 dia. 15 nos 14. ms barrel 40/45 gln. capacity (leaky) 47 nos , lot no.3(lot of three items) 1. scrap waste paper 7575 kgs 2. scrap teakwood 53 kgs 3. scrap deal wood 20 kgs , lot no.4(lot of three items) 1. scrap ms/rts grill 22486 kgs 2. cond. computer scraps 50 kgs 3. cond. type 3 officer pc 16 set , lot no. 5 (lot of fourteen items) 1. scrap brass 46 kgs 2. energy meter scrap (electro mechanical) 1867 kgs 3. cond. megger of sizes 1 no 4. scrap burnt meter/hq 2628 kgs 5. burnt static meter 9732 kgs 6. cond. relay of sizes 1 no 7. cond. exhaust fan motor (small) 1 no 8. cond. digital micro ohm meter 1 no 9. cond. ct /lt coil 9 nos 10. cond. valve scrap 1 kg 11. cond. motor of various capacity (5hp) 1 no 12. cond.resistant kit 1 kg 13. cond. spilt ac various capacity 1 no 14. cond. window type 2 ton air conditioner with stabilizer 2 nos , lot no. 6(lot of two items) 1. cond. metering set of various capacity w/o oil–29 nos i) 11 kv 20/5a 1 no(apoorv 37062 2018) ii)11 kv 20 10/5a 1 no (crel 121766 2008) iii)11 kv 50/5a 1no(pgr 9220 2019) iv)11 kv 100/5a 1no( vidyuth 9846 2016) v)11 kv 100 50/5a 2 nos 1)vidyuth 453 1505 2007, 2)ae 1664 1996, vi)22 kv 10/5 5a 2 nos 1)ascott 224813 2013, 2)ascott 224799 2015, vii)22 kv 20 10/5a 9 nos 1)ascott 2522 2006, 2)ascott 2003 2005, 3)ascott 2520 2008, 4)crel 121251 2008, 5)crel 120736 2007, 6)ascott 2805 2008, 7)delta 555 2006, 8)ascott 2377 2006, 9)ascott 2840 2008, viii)22 kv 40/5a 2 nos 1)amptech at/22/277 2016, 2)ascott 223823 2012, ix)22 kv 40 20/5a 3 nos1)ascott 3058 2008, 2)crel 121273 2008, 3)ascott 2071 2005, x)22 kv 50/5 5a 1 no 1)crel 127084 2014, xi)22 kv 60 30/5a 3 nos1)elcont 2297/b 3 1997, 2)ascott 223622 2011, 3)crel 121276 2008, xii)22 kv 100 50/5a 3 nos 1)ascott 2669 2008, 2)crel 117904 2004, 3)crel 124170 2011, 2. cond. distribution transformer of various capacityw/o oil (aluminum wound) 10 nos i).200 kva /11 kv – 1 no1) danya dec/600/alu 1989 ii)100 kva /11 kv – 7 nos1) into tech it 17475 1991 2) vijay 9620 1995,3) senthil ad/204/1235 1997 4) indo tech it 13305 1980, 5) ashok 2746 1974 6) vijay 5709 1991,7) jay shree jt – 576 2007 iii)63 kva /11 kv – 2 nos1) venkateswara am/1496/8328 1992 , 2) magdyne 631049 1988 , lot no. 7(lot of six items) 1. scrap aluminum including aac cut bits 79 kgs 2. scrap acsr 8025 kgs 3. scrap aaac 137 kgs 4. scrap aluminum transformer winding 74.950 kgs 5. scrap vir/wp wire with aluminum core 32 kgs 6. scrap all aluminum alloy 19 kgs , lot no. 8(lot of one item) 1. cond. distribution transformer of various capacityw/o oil (copper wound) 30 nos i) 250kva/22kv 2 nos. 1) rel 25025 1936 ,2) rel m 8496 na ii)200kva/22kv – 8 nos 1) rel m 12619 1985 86, 2) hindusthan 3288 1992, 3) danya dec/1271 1994, 4) apex t 035/2350 1970 , 5) indotech it 894 1979,6) hidusthan 3286 1992 , 7)indotech it 8407 1986,8) eltra et 6202 1980. iii)150kva/22kv 1no 1) amul 1947 1970 iv)100kva/22kv 13nos 1) perkure 61251 18 1957, 2) star delta 2075 1970, 3) hindustan 2400 1989, 4) voltamp 62/41 1971, 5) gresham 216850 1950, 6) indo tech it 3318 1980 81, 7) apex t 081/7347 1970 71, 8) eltra t 02/203 1970 , 9) bajaj 1001334 1962, 10)electromech 3171 1996 , 11) rel m 2741 1992 , 12)vigneswara 499 1989,13) hindusthan a 1060 na, v)100kva/11kv 2nos 1) crompton greaves b123/63 1972, 2) volt amp jn 227/46 1971 vi)63kva/22kv 2nos 1) hindusthan 910 1987 , 2) hindusthan 5623 1996 vii)50kva/11kv 2nos 1) kirloskar 50a724/m na , 2) crompton greaves 3522 1967 , lot no. 9(lot of one item) 1. empty wooden drum 3 to 6 dia – 211 nos...

Council Of Scientific And Industrial Research - Tamil Nadu

40538235 tender for various minor repair works in institute area at csir cecri, karaikudi; 1 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 2 applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 3 water thinnable cement primer 4 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 5 two or more coats on new work 6 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 7 two or more coats on new work 8 providing and laying a single layer of tarfelt sheet weighing not less than 1kg / sqm of approved quality / approved by the engineer in charge over one coat of bituminous emulsion paint and pressed wellwith existing ac sheet roofing including ridges as directed ( one coat of bituminous emulsion paint to be paid separetly ) . 9 taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the engineer in charge. 10 providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to is: 1868 with minimum anodic coating of grade ac 15 ) of approved design / pattern, with approved standard section and fixed to the existing window frame with c.p. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of engineer in charge. ( only weight of grill to be measured for payment ) . 11 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fastenersto be paid for separately ) : 12 for fixed portion 13 powder coated aluminium ( minimum thickness of powder coating 50 micron ) 14 for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) 15 powder coated aluminium ( minimum thickness of powder coating 50 micron ) 16 providing and fixing 9 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in charge. pre laminated particle board with non decorative lamination on both sides 17 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) : 18 with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) 19 providing and fixing bright / matt finished stainless steel handles of approved quality & make with necessary screws etc all complete. 150mm 20 providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. 21 providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. 22 twin rubber stopper 23 providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 24 providing & applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg / 10 sqm. one coat of self priming of cementatious waterproofing polymer ( dilution with water in the ratio of 1:1 ) and two coats of cementatious waterproofing polymer ( dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of engineer in charge. 25 providing & fixing sun control film in the glass paneled steel windows, inclusive of surface cleaning, pasting etc., and fix the film as per the instructionof the site –engineer in charge. 26 finishing walls with acrylic smooth exterior paint of required shade : 27 new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) 28 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 29 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 30 supplying chemical emulsion in sealed containers including delivery as specified. 31 chlorpyriphos emulsifiable concentrate of 20% 32 diluting and injecting chemical emulsion for post constructional anti termite treatment ( excluding the cost of chemical emulsion ) : 33 treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 ce ment : 2 coarse sand ) to the full depth of the hole : 34 with chlorpyriphos e.c. 20% with 1% concentration 35 removing and re fixing of existing steel glazed door / windows after necessary alternation including necessary repair work of proper locking arrangements ( using ms flats, etc. ) and hinges as per site requirement as directed by the engineer in charge. ( upto 4.00 sqm of shutters ) 36 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 37 all kinds of soil 38 pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 39 cleaning the man holes / septic tanks including removal of blockages in the existing lines by mechanical means including transportation charges as directed by the engineer in charge ( 6000litre capacity ) 40 making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 41 for pipes 100 to 250 mm diameter 42 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 43 hot finished welded type tubes 44 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 45 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 46 in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 47 providing and fixing expansion hold fasteners on c.c. / r.c.c. / brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. 48 wedge expansion type 49 fastener with threaded dia 12 mm 50 repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of engineer in charge. 51 providing and fixingpvc swr pipes type b conforming to is:13592 including jointing with necessary fittings as directed by the engineer in charge. 150mm diameter 52 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with r.c.c. top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) , inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design : inside size 90x80 cm and 45 cm deep with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 53 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 54 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources ) 55 1:4:8 ( 1 cement : 4 manufactured sand derived from recycled concrete aggregate ( rca ) : 8 graded stone aggregate 40 mm nominal size recycled aggregate ( ra ) 56 providing and fixing unplasticized polyvinyl chloride ( upvc ) pipes, including all upvc threaded fittings. this includes jointing of pipes & fittings with one step suitable solvent and testing of joints complete as per direction of engineer in charge. 80mm dia upvc pipe 57 providing and fixing upvc ball valve of approved quality, high or low pressure, with plastic floats complete as directed by the engineer in charge. 80 mm dia upvc ball valve 58 making connection of g.i. distribution branch with g.i. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 59 50 to 80 mm nominal bore 60 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 61 all kinds of soil. 62 half brick masonry with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundations and plinth in : 63 cement mortar 1:4 ( 1 cement : 4 coarse sand ) 64 12 mm cement plaster of mix : 65 1:6 ( 1 cement: 6 coarse sand ) 66 grouting the joints of stone masonry having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade ( 0.10 kg of hardener and 0.20 kg of resin per kg ) , including filling / grouting by suitable gun / pump at required pressure and finishing complete as per direction of engineer in charge. 67 ( a ) designing, fabricating, testing, installing and fixing in position curtain wall with aluminium composite panel cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. ( b ) providing, fabricating and supplying and fixing panels of aluminium ( c ) composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick fr grade mineral core sandwiched between two aluminium sheets ( each 0.5mm thick ) . the aluminium composite panel cladding sheet shall be coil coated, with kynar 500 based pvdf / lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer ( service ) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. the fastening brackets of aluminium alloy 6005 t5 / ms with hot dip galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, ss 316 pins and anchor bolts of approved make in ss 316, nylon separators to prevent bi metallic contacts all complete required to perform as per specification and drawing the item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. base frame work for acp cladding is payable under the relevant aluminium item.s the contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the engineer in charge. however, for the purpose of payment, only the actual area on the external face of the curtain wall with aluminum composite panel cladding ( including width of groove ) shall be measured in sqm. up to two decimal places. 68 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete. 69 fixed to steel windows by welding 70 providing and fixing square mouth s.w. gully trap class sp 1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 71 150 x 100 mm size p type 72 with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 73 providing and fixing 63 mm dia pvc pipes ( 4kg / cm2 ) ( finolax or equivalent ) complete with necessary fittings and clamps including cutting and making goodthe walls etc. 74 providing and fixing double scaffolding system ( cup lock type ) on the exterior side, up to seven story height made with 40 mm dia m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .the scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in charge .the elevational area of the scaffolding shall be measured for payment purpose .the payment will be made once irrespective of duration of scaffolding. note: this item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. 75 supplying and fixing self adhesive decorative film for glass doors / winows / glass partition / backing of suitable boards including requireddesign as directed by the engineer in chage....

Indian Army - Tamil Nadu

40537915 bids are invited for cb / 8455 000527 armlet mp cc2 / 8465 000142 container soap plastics ch / knd / niv / cl2 / 242 overall comb disp w / patt indian a / l s1 cc2 / 8405 004534 shirt men angola drab p / wool 73 patt s / 2 cn / knd / niv / cl2 / 114 tin mess alluminium alloy total quantity : 11478...

Nuclear Power Corporation Of India Limited - Tamil Nadu

40506010 tender for preparation of drawings, supply of cs structural materials, gi/ zinc aluminium alloy coated profile sheet, fabrication, supply and application of painting, construction of semi covered protective sheds, disassembly of erected shed, modification and re assemblies with modified structural steel material, excavation of earth, providing and laying of pcc, supply and fixing of m/s hilti anchor fastener...

Military Engineer Services - Tamil Nadu

40501739 tender for repair / maintenance of external electrical infrastructure and connected items in domestic and technical area including lca area 2 m&l for removing of 160 watt flame proof lights along with hanging iron rods fixed in sun shelters by disconnecting the electric cable connections and re fixing in same sunshelter but, other locations by necessary fixing arrangements like welding/clamp/nut bolt etc duly connecting with electric supply and testing complete all as specified and directed by the engineer in charge. (total sunshelters 06 nos) 3 note for item no 2 : the following items are deemed to be inclusive of quoted rate : 4 (a)the above job shall be carried out by a trained electricians only 5 (b)the rate quoted for shifting of all lights in one sun shelter shall be considered as on job. each sunshelters provided with 16 nos flame proof lights 6 (c) each sun shelters have approx. height of 10 meter and the ceiling of each sun shelters have provided with anti bird net. for removal of lights, anti bird net may be removed and kept without any damagefor re fix after the fixing of lights. the contractor has to consider the above aspects while quoting the rate. the quoted rate shall deemed to be inclusive for removing and re fixing of the anti bird net if necessary and nothing extra shall be admissible on this account. 7 (d) necessary t&p, safety belt, vehicle, aluminium ladder, cranes etc. shall be arranged by the contractor and cost for the same shall deem to be included in the quoted unit rate 8 (e)all safety measures and provn of all safety devices, first aid box etc shall be provided by the contractor.contractor will be solely responsible forfull safetyof the persons deployed for providing the services and department will have no liability for any type of accident/injury of any type. unit rate quoted will be deemed to include the cost of the same and no extra payment shall be made on this part. 9 (f)all type of t & p, pvc insulation tapes, minor nuts/ bolts/ washers etc required shall be provided by the contractor without any extra cost to department. 10 (g)additional cables required if any shall be measured and paid seperately under relevent item here in after. 11 supply onlypvc insulated copper conductor cable 1.5 sqmm, single core round flame proof flexible cable for connection of flame proof lights, complete all as specified and as directed. 12 m&l for periodical servicing / maintenance of 150 watt high bay lights fixed in hangars on quarterly basis including checking of loose connections tightening of loose nut bolts if any and cleaning and testing complete all as specified and directed by the engineer in charge.(total hangers 05 nos) 13 note for item no 12 : the following items are deemed to be inclusive of quoted rate : 14 (a)the above job shall be carried out by a trained electricians only 15 (b)the rate quoted for servicing of all lights in one hangers shall be considered as on job. the payment shall be made on quarterly basisonly after testing of all lights in each sun shelter satisfactorily by the engr in charge. 16 (c) each sun hangers have approx. height of 12 meter and the ceiling of each hangers have provided with anti bird net. for the servicing of the lights, the anti bird net may be removed and kept without any damagefor re fix after the fixing of lights. the contractor has to consider the above aspects while quoting the rate. the quoted rate shall deemed to be inclusive for removing and re fixing of the anti bird net if necessary and nothing extra shall be admissible on this account. 17 (d) necessary t&p, safety belt, vehicle, aluminium ladder, cranes etc. shall be arranged by the contractor and cost for the same shall deem to be included in the quoted unit rate 18 (e)all safety measures and provn of all safety devices, first aid box etc shall be provided by the contractor.contractor will be solely responsible forfull safetyof the persons deployed for providing the services and department will have no liability for any type of accident/injury of any type. unit rate quoted will be deemed to include the cost of the same and no extra payment shall be made on this part. 19 (f)all type of t & p, pvc insulation tapes, minor nuts/ bolts/ washers and cables etc required for maintaining the services shall be provided by the contractor without any extra cost to department. 20 m & l for disconnecting of burnt/ damaged cables from panels/ junction boxes etc, cutting out the burnt out ends, making new end joints by supply and fixing new aluminium lugs/ insulation tapes etc and reconnecting using new nuts/ bolts/ washer etc and restoring three phase and neutral in the junction box complete all as directed for the 25/ 35 sqmm 3.5 core size of lt underground armoured cablescomplete all as specified and directed. 21 note for item no 20 : earth work required for extending the incoming/ outgoing cable in junction box/ panel board etc shall be deemed to be included in the unit rate quoted. 22 s & f gi tubing 40/50 mm bore light grade 1.2 mtr long bent to shape as required with clamps for fixing of street light on poles/ walls including nuts, bolts, washers clamps of suitable size including taking down existing onecomplete all as specified and directed. 23 s & f singlepole mcb 6 to 32 amps, 240 v, 50 hz acsuitable for ‘c’ curve, 10 ka breaking capacity conforming to is 8828 of 1996including taking down existing one complete all as specified and directed. 24 supply and fixing in repairs led flood light 100 watt 230 v ac outdoor type with thermal management in multiple optics and equipped with ip66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. 25 supply and fixing in repairstpn, mcb 40 to 63 amp, 240 v, 50 hz acsuitable for ‘c’ curve, 10 ka breaking capacitycomplete conforming to is 8828 of 1996 completeall as specified and directed 26 excavation in trenches in hard/dense soil not exceeding 1.5m wide and not exceeding 1.5 metre in depth for laying of cable and not exceeding 10 sqm on plan for poles, struts, stays etc. and not exceeding 1.5 m in depth and getting out completeall as specified and directed 27 riddling sand obtained from excavation for cable protection 8cm under the cable and 15cm above the cable in trench and get the thick layer of 18cm after ramming complete all as per specified and as directed. . 28 note for item no 27 : in case sufficient sand not obtained from excavation, the rate is deemed to be inclusive for additional qty of sand requiredto be obtain from outside md land as directed by the engineer in charge 29 removing excavated materials not exceeding 50m distance and depositing where directed at level not exceeding 1.5 m above the starting point complete all as per specified and as directed. 30 s&f fly ash bricks using modular bricks as in cable protection cover including taking down existing bricks of any size complete all as per specified and as directed. 31 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soil complete all as specified and directed. 32 s&f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 25 sqmm 3.5 core laid in trenches /ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets, taking down existing cable etc complete all as specified and directed. 33 note for item no 32 : excavation and earth work shall be measured and paid separately. 34 s & f cable jointing kit for 1.1 kv grade cable for outdoor straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core xlpe armoured aluminium conductor cable of size 10 sqmm to 16 sqmm complete all as specified and directed. 35 m & l for cutting existing road/pcc/drain for laying of di/gi or any type of pipe including necessary earthwork, excavation exc 600mm depth but not exc 1mtr depth, wide 800mm including making existing surface with pcc 1:2:4 type b1 using 20mm aggregate thickness of concrete is 150mmcomplete all as specified and directed. 36 note for item no 35 : the tenderer shall take into consideration for following points while quoting his rate for this item andthe unite rate is deemed be included for : 37 (i) earth work excavation in any type of soil 38 (ii) returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick complete all as specified and as directed. 39 (iii) removing excavated material to out side md land 40 (iv)laying of any type/any bore of pipe in trenches including taking down any description. supply of pipe will be measured and paid separately 41 (v)150 mm thickpcc 1:2:4 type b1 as inany type of road 42 (vi) gi pipe requiredfor cable protection shall be measured and paid separately under respective item. but labour required for take the cable through gi pipe and laying in trench shall deemed to beincluded in the rate quoted. 43 supply only gi pipe 50 mm bore medium grade for cable protection completeall as specified and as directed by engr in charge. 44 m & l for disconnecting of burnt/ damaged cables from panels/ junction boxes etc, cutting out the burnt out ends, making new end joints by supply and fixing new aluminium lugs/ insulation tapes etc and reconnecting using new nuts/ bolts/ washer etc and restoring three phase and neutral in the junction box complete all as directed for the 10/16 sqmm 4 core size of lt underground armoured cablescomplete all as specified and directed.. 45 note for item no 44 : earth work required for extending the incoming/ outgoing cable in junction box/ panel board etc shall be deemed to be included in the unit rate quoted. 46 m & l for cleaning vegetation around the lt pole completely root out from soil and clean the surface onemtr around the pole of street lights complete all as specified and as directed. 47 note for item no 46 : removing of accumulated earth depth upto 15cm cleaning / cutting the grass with hand operated petrol/ kerosene driven grass cutting machine andremoving thegrass waste to outside md land is deemed to be included in quoted rate. 48 s&f powercontactors 40 amps, 4 pole,415v, including taking down old item complete all as specified and as directed. make : cat no 412553 of legrand or equivalent of l&t/ siemans 49 m & l for preparing surfaces by removing exisiting faded sky blue and white straps on pcc poles and applying a coat of sky blue/white straps painting with synthentic enamel paint, eachsky blue/white straps of 30 cm height up to 1.5 mtr from top of pcc coating, writing pole no with white paint on black base of pcc pole by sentensile measure includingapplaying one coat of synthetic enamel paint to clamps/cross arm/street light gi bracket fixed on pole complete all as specified and as directed 50 supply & fix in repair pvc insulated copper conductor cable 1.5 sqmm, 3 core round flexible for connection of street light fitting, complete all as specified and as directed. 51 m&l sub main wiring for circuit complete with 2 runs of 1.5 sqmm single core pvc insulated, unsheathed frls1100 volt grade multi stranded copper conductor cable drawn through and incl suitable size non metallic pvc conduit and accessories complete fixed surface to wall/roof/ceiling etc and 1 run of 1.5 sqmm single core pvc insulated, unsheathed frls 1100v grade multi stranded copper conductor cable as earth continuity conductoretc including taking down existing sub main wiring complete all as specified and directed. 52 note for item no 51 : (a) two runs of 1.5 sqmmpower cable , one run of 1.5 sqmm earth conductor and one run of pvc conduit/casing capping will be measured as one length. 53 (b)connections of cables with mcbs or bus bars shall be done through appropriate size brass/copper thimbles. 54 m & l for removing steel swagedtubular pole 8.5/9 mtr long for providing suitable new bracket for fixingstreet lightand re fixing the poleincluding necessary pcc 1:4:8, type d2 (using 40 mm graded stone aggregate) for foundation of 50 x 50 x 45 cm and coping with 1:2:4, type b1 (using 20 mm graded stone aggregate) complete all as specifiedand directed by engr in chrage 55 s&f in repairs connector suitable for fixing of cable of size cross sectional area 10 sqmm to 25 sqmm armoured/pvc for preventing of short circuiting of cable in junction boxes, complete all as specified and as directed. 56 m & l for preparing the existing painted steel surface and painting with one coat of aluminium paint on cross arms, clamps, ms flat and street light brackets if any on steel / rcc pole for doublecross arm for three phase4 wire system complete all as specified and directed. 57 supply and fixing in repairs led flood light 210 watt 230 v ac outdoor type with thermal management in multiple optics and equipped with ip66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.. 58 s&f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 16 sqmm 4 core laid in trenches /ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets, taking down existing cable etc all as specified and directed. 59 note for item no 58 : excavation and earth work shall be measured and paid separately. 60 supply, transporting to site, erecting and fixing in position, steel tubular swaged poles of 9mtr longtype 410 sp 31 is 2713 marked complete with ci/ ms base plate, finial taper plug, bolts, nuts, washers and screws as specified, drilling of necessary holes including painting with two coats of aluminium paint overa coat of red oxide primer on exposed surface and black bituminous paint on steel surface embedded in concrete externally and throughout internally and painting 03 nos of band /strips with fluorescent , po box red synthetic enamel paint (30 cm wide each) at a distance of 30 cm from plinth block and number of poles including taking down existing one completeall as specified & directed by engineer in charge. 61 note for item no 60 : earth work excavation, pcc foundation, coping will be measured and paid separately. the rate for pole shall also be included painting to steel tubular pole (in side and out side). 62 m&l cement concrete 1:4:8,type d2 (using 40mm graded stone aggregate ) including necessary form work for pole foundation complete all as specified and directed by engr in charge . 63 m&l cement concrete 1:3:6 type c2(using 40mm graded stone aggregate) including necessary form work for pole foundation complete all as specified and directed by engr in charge . 64 m&l pcc 1:2:4 type b 1 using 20mm graded stone aggregates as in pole coping completeall as specified & directed 65 s&f powercontactors 63 amps, 4 pole,415v, including taking down old item complete all as specified and as directed. make : cat no 412557 of legrand or equivalent in ps 66 m & l for preparing the painted steel surfaces of existing lt steel tubular pole including cross arms, clamps ms flats, steel light bracket if any etc and applying one coat of aluminium paint(above ground/coping level) not exc 8 mtr long including painting of strips of height 0.3mtr each (three nos sky blue and three nos white), writing pole no with black paint with letters/figures 7.5 cm high and tightening of cross arms, clamps and street light brackets complete all as specified and directed. 67 s&f led aviation obstruction light with ip 66 protection water clear poly carbonate uv stabilized dome neoprene rubber with bind spike with 302 nos led bulbs including necessary electric connections including 2.5 sqmm, 2 core, pvc copper cables fixed on wall with 20mm dia pvc conduit from db to light fitting fixed in and including gi pipe 25mm dia 1 mtr long grouted with pcc complete/ binding with existing angle frame etc complete including taking down existing one complete all as specified and directed.make : bajaj cat no 110731 or equivalent in wipro/ cg. 68 m & l earthing testing, identifying the earth and recording of test results in prescribed format all as directed by engineer in charge. each earth pit result be submitted to engineer in charge duly signed by user and mes rep for earth test less than 1 ohm (10 pits and more considered 1 earthing point) 69 earthing testing, identifying the earth and recording of test results in prescribed format all as directed by engineer in charge. each earth pit result be submitted to engineer in charge duly signed by user and mes rep for earth test less than 3 ohm (4 pitsand more considered 1 earthing point) 70 earthing testing, identifying the earth and recording of test results in prescribed format all as directed by engineer in charge. each earth pit result be submitted to engineer in charge duly signed by user and mes rep for earth test less than 4 ohm (3 pits and more considered 1 earthing point) 71 earthing testing, identifying the earth and recording of test results in prescribed format all as directed by engineer in charge. each earth pit result be submitted to engineer in charge duly signed by user and mes rep for conventional type earthing (individual pit) 72 note for item no 68 to 71 : the following items are deemed to be inclusive of quoted rate : (i)the above job shall be carried out by a trained technician having iti in electrical and well known regarding earthing test. documentary proof of the education of tradesman shall be produced, before commencement of work. 73 (ii) the afore said test will be carried out in presence of user and mes representative.(iii) two party (consisting 2 x 1 no. technician with 2 x 1 no. helper) will report every morningat 9 am to je e/m for daily earth testing. 74 (iv) they will testearth resistance every day ( not more than 10 nos earthing/day) in presence of user & mes rep and willrecord it in prescribed format , same will be put to engineer in charge,je e/m duly signed by user & mes rep on very next day, failing which a sum of rs. 100.00 per day will be recovered from the contractor. 75 (v) earth resistance tester will be provided by the contractor. (tester should be calibrated from authorised company/ lab). 76 (vi) contractor will be responsible for pouring of water in the earth pits weekly at their own arrangement with water tanker, etc. (water will be provided by the contractor at his own arrangement and nothing extra will be admissible). 77 (vii) checking of earth pits existing and improve it by watering / adding a layer of salt/ magnesium sulphate/ charcoal, etc. 78 (viii) contractor will be responsible for marking of earth check date and due date on existing plate with paint as specified by engineer in charge. 79 (ix)contractor will be responsible for cleaning of bushes and grass all around upto 1.50 metre area of existing earth pit with tightening of strip. 80 (x)ep no should be mentioned on individual earth pits and er value of installation etc all as specified and directed by engr in charge. 81 (xi)it will be the responsibility of the contractor to liase with station authority to obtain security pass as per station rules for entering/ working in high security tech area. 82 checking of any breaking in the link of earth strip wire of galvanised/copper/aluminium strip any size and jointing them by exothermic welding or brazing including taking down old unserviceable one, complete all as specified and as directed. 83 attending unserviceable/ non functional street light complaints (for street light/perimeter lights/high mast light/flood light etc of any type/size fitted on poles/walls/post/pillars etc)by deploying technically qualified and experienced technicians to find out defective/taking out unserviceable parts such as electronic driver, pvc insulated copper conductor cable for connecting street light fittings etc and repairing by changing the defective parts including minor repair to cable connection/loose connection, screws, nuts & bolts and insulation tap to insulate the lt joint etc and testing complete all as specified and as directed for domestic area of old kalpa colony, new kalpa colony, mehra colony, map qrts, akash enclave, gulmohar enclave, kiran enclave, mes colony, afwwa, various connecting roads and other facilities such as shopping complex/ various institutes/ messes/ play ground, complete perimeter etc located in complete domestic area andtechnical area at af station sulur 84 note for item no 83 : the following items are deemed to be inclusive of quoted rate : 85 (a)the above job shall be carried out by a trained electrician having iti in electrical, documentary proof of the education of tradesman shall be produced before commencement of work. 86 (b)supply only items to be delivered/ supplied to age e/m store yard as per qty asked by engineer in charge with in one calendar month from the date of commencement of contract and these items will be issued from age e/m store yard for attending unserviceable/ defective street light complaints. 87 (c)contractor or his authorised representative has to inspect all street/ security lights on daily basis at their own arrangement between 7.00 pm to 9.00 pm and maintain the record in register which will be put up to engineer in charge/ je on the very next day. 88 (d) a joint inspection for serviceability of all street/security lights will be carried out from 7.00 pm to 9.00 pm on every monday by engineer in charge/ je (e/m)/ user along with contractor or his authorised representative. 89 (e) contractor has to arrange own moveable generatorof suitable capacity for repairing and testing of the street/ security lights, defect rectification of cables, etc. and to check the serviceability after repair.no electricity shall be provided by the department on this account. 90 (f) quoted unit rate shall deemed to be inclusive of attending any breakdown of street/ security lights during night. contractor has to arrange electrician and helper and all necessary t&p and equipments to remove the breakdown. fault will be intimated through telephone/ sms. 91 (g)in case of any delay in attending the complaint more than 12 hrs after handing over routine/urgent work, the contractor shall be liable to pay the penalty as described in penalty clause given here as under. 92 (h) the penalty shall be applicable to the contractor if the delay is noticed by the engr in charge more than twelve hrs after handing over works of urgent nature to the contractor. the engr in chargeshall handover the slip containing specification of work to the contractor by lodging the time and signature of contractor be obtained on slip.the contractor shall attend the complaint immediately and shall report to engr in charge with in 12 hrs. the contractor will keep his tradesmen in stand by for attending any routine / urgent works from the executive.if the nature of job is such that the work cannot be completed within period of 12hrs then the facts shall be brought to the notice of the ge/engr in chargeand the period for the working to the complaint shall be decided by the ge/eic. if the delay is more then twelve hrs period and the ge is not satisfied with the reason for delay then penalty at the rate of rs 50/ per job shall be deducted from the dues of the contractor. please note that this penalty is exclusively other then the condition 56 of iafw 2249 and shall be treated as interim condition of the contract and shall be enforce above as and when delay in individual job is noticed and no claim whatsoever on this account shall be entertained by the dept.the decision of the accepting officer is this regards shall be final and binding. 93 (j) contractor has to ensure serviceability of all street/ security lights of domestic & technical area on daily basis in any weather condition at their own arrangement. 94 (k)contractor shall provide conveyance to the deployed labour for maintaining the services without any extra cost to department. 95 (l)vehicle mounted ladder for maintaining services shall be provided by the contractor at no extra cost to department. 96 (m) materials requiredfor the repairing of the lights shall be measured and paid separately under respective item(s). but labour required for taking down, dismantling, repairing and replacing parts and reinstalling and testing the street lights fittings shall deemed to beincluded in the rate quoted. 97 (n)necessary t&p, safety belt, vehicle, aluminium ladder, etc. will be arranged by the contractor and cost for the same shall deem to be included in the quoted unit rate. 98 (o)all safety measures and provision of all safety devices, first aid box etc shall be provided by the contractor.contractor will be solely responsible forfull safetyof the persons deployed for providing the services and department will have no liability for any type of accident/injury of any type. unit rate quoted will be deemed to include the cost of the same and no extra payment shall be made on this part. 99 (p)all type of t & p, pvc insulation tapes, minor nuts/ bolts/ washers etc required for maintaining the services shall be provided by the contractor without any extra cost to department. 100 (q)attending and repairing complaint for onelightof any type shall be measured and paid as one job. 101 (r)earth work (if necessary at site) for removing of any cable fault will be measured and paid under respective items. 102 (s) the contractor shall maintain a record of all urgent work at and if the work is repeated due to poor workmanship, he will be liable to repair the same without any extra expenditure to the govt. 103 (t)contractor shall provide contact details of his responsible person(s) for any emergency. 104 (u) any materials replaced which are not specified in schedule of credit will be deposited to mes store yard without any extra cost to the department. 105 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 10 watt, complete all as specified and as directed. 106 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 20 watt, complete all as specified and as directed. 107 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 36 watt, complete all as specified and as directed. 108 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 45 watt, complete all as specified and as directed. 109 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 76 watt, complete all as specified and as directed. 110 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 120 watt, complete all as specified and as directed. 111 supply only electronic driver with input voltage 220 to 240volt and output voltage suitable for led light fitting of capacity 160 watt, complete all as specified and as directed. 112 s & f gi water tubes of size of 20 mm bore medium grade isi markedwith all fittings such as bend, elbow, socket, tee etc and fixed completeto wall and ceilings or laid in floors including taking down old unserviceable one, complete all as specified and as directed. 113 s & f bib taps 20 mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete including taking down old unserviceable one, all as specified and as directed. 114 s & f in repairs air termination single pointed aluminium rod dia upto 20mm and length upto 300mm including provision of cement concrete 1:2:4 (20mm graded stone aggregate) block 300x300x300 mm and necessary fixing arrangement at roof, complete all as specified and as directed. 115 note for item no 114: if threaded of the rod is damaged then contractor will be responsible for cutting of thread for fixing the rod. any minor repairs/ materials is deemed to be included. 116 s & f aluminium strip 25 x 3mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including taking down existing one complete all as specified and directed. 117 s & f galvanised iron tubing/pipe 40mm bore, light grade for strip protection, fixed in walls/floors with suitable type of clamps, etc. including taking down old unserviceable one, complete all as specified and as directed. 118 s & f in repairs stainless steel screw/ nut and bolts (machine made) with hexagonal or square heads at one end and screwed the other each screwed end to be fitted with washers and one hexagonal or square nut of dia 5mm to 10mm, n. exc 25mm long complete all as specified and directed. 119 s & f mild steel sheet of size approximate 300x200x1.6mm thick sheet egg type, half round type, rectangular type and triangular type with welded 1 (inch) dia 2 (feet) long mild steel pipe with duly different synthetic enamel paint cutting of equipment earth/ lighting arrester earth/ signal earth etc. complete as specified duly painted as specified and marking of earth plate number/ description of earthing/type of earthing on plate with white paint including earth plate no. and earthing resistance with earthing check date and earthing check due date including taking down old unserviceable one, complete all as specified and as directed 120 excavation in existing defective earth pit as notified by the engr in charge and spreading common salt, charcoal dust and magnesium sulphate complete all as specified and directed by engr in charge. 121 note for item no 120: common salt, charcoal dust and magnesium sulphate shall be measured in relevant item of schedule. however labour element for spreading is deemed to be included. 122 supply only common salt commercial in trenches to improve the er value of existing earth pits complete all as specified and directed. 123 supply only charcoal dust/breeze each bags of 25 kg in trenches to improve the er value of existing earth pits complete all as specified and directed. 124 note for item no 123: earthing charcoal dust/breeze shall be supplied in packing as per originally packed by the manufacture 125 supply only magnesium sulphate in trenches to improve the er value of existing erath pits complete all as specified and directed.. 126 s&f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 10 sqmm 4 core laid in trenches /ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets, taking down existing cable etc all as specified and directed. 127 note for item no 126 : excavation and earth work shall be measured and paid separately. 128 supply and fixin replacement of high power led street light fittings energy saving luminaire with lens , capacity 36 watt with system efficacy (lm/w) shall be 100 lumenper watt or more lumens per watt, total system lumen not less than 3600 lumens, pf not less than 0.95, cri not less than 70,colour temp. 5000k to 6500 k, surge protection not less than 5 kv, high pressure die cast aluminium alloy lm6 housingip 65/66 class 1 protection, toughened glass cover, driver efficiency > 85% with constant output of current and voltage against input voltage variation 120 to 270 volt at 50 hz ( + 5%), thd< 10% completeincluding taking down existing complete all as specified and directed. 129 s&f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 10 sqmm 2 core laid in trenches /ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets, taking down existing cable etc complete all as specified and directed. 130 s&f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 6 sqmm 2 core laid in trenches /ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets, taking down existing cable etc complete all as specified and directed. 131 note for item no 129 & 130 : excavation and earth work shall be measured and paid separately. 132 supply and fixin replacement of high power led street light fittings energy saving luminaire with lens , capacity 60 watt with system efficacy (lm/w) shall be 100 lumenper watt or more lumens per watt, total system lumen not less than 3600 lumens, pf not less than 0.95, cri not less than 70,colour temp. 5000k to 6500 k, surge protection not less than 5 kv, high pressure die cast aluminium alloy lm6 housingip 65/66 class 1 protection, toughened glass cover, driver efficiency > 85% with constant output of current and voltage against input voltage variation 120 to 270 volt at 50 hz ( + 5%), thd< 10% completeincluding taking down existing complete all as specified and directed. 133 s & f synchronising electronic timer unit operated on ac 230 volts, 24 hrs clock time for controlling street lights including taking down old unserviceable timer switches complete all as specified and directed.make : cat part no : 4126 41 of legrand or equivalent in l&t, abb. 134 m & l cleaning of existing solar street light panels fixed above street light pole of approximate height 6 meter by using wet cloth dipped in soap water including the panel perimeter complete all as specified and directed. 135 note for item no 134: (i) the contractor shall be responsible for arrange necessary conveyance vehicle, aluminium self supporting ladder/bamboo ladder, bucket, soap powder, cloths etc and the quoted rate shall be deemed to be inclusive for the above. 136 (ij) contractor has to ensure serviceability of solar street light panel of domestic & technical area on daily basis in any weather condition at their own arrangement. 137 (iii)contractor shall provide conveyance to the deployed labour for maintaining the services without any extra cost to department. 138 (iv)vehicle mounted ladder for maintaining services shall be provided by the contractor at no extra cost to department. 139 (v)necessary t&p, safety belt, vehicle, aluminium ladder, etc. will be arranged by the contractor and cost for the same shall deem to be included in the quoted unit rate. 140 (vi)all safety measures and provision of all safety devices, first aid box etc shall be provided by the contractor.contractor will be solely responsible forfull safetyof the persons deployed for providing the services and department will have no liability for any type of accident/injury of any type. unit rate quoted will be deemed to include the cost of the same and no extra payment shall be made on this part. 141 m&l in repairs earthing with galvanised earth plate electrode 600x600x 6mm thick burried directlyin ground (earth pit not less than 2.25 metre below ground level) with top edge of the plate not less than 1.50 metre below ground level, connected with galvanised earth strip of size 25x6mm by means of bolts, nuts, check nuts and washers of gi or steel and connected earthing testing point/bus bar including gi 40mm bore (dia) light grade protection pipe, earth plate surrounded by a packed thickness of char coal or coke dust mixed with common salt magnesium sulphate (1 : 1: 0.5) in alternate layers of not exc 150mm thick, pcc pit in cement concrete 1:3:6 (20mm graded stone aggregate) and pre cast rcc cover slab of size 350x350x50 mm in cement concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia tmt bars @ 100mm centre to centre in both ways, gi wire mesh, funnel with gi watering pipe 20mm bore (dia) medium grade including necessary excavation in soft/loose soil, returning, filling in and removal of surplus spoil upto a distance of 50.00 metre and all as shown in electrical plate no. 3 of mes schedule part i and testing on completion, complete all as per specified and as directed. 142 note for item no 141 : (a)all joints should be joined by exothermic welding or brazing. 143 (b)after completion of work earthing shall be tested by the contractor in presence of engineer in charge, user and proper record shall be maintained duly signed by all concerned. 144 (c)earth resistance tester will be provided by the contractor. it should be calibrated from authorised company/ lab.. 145 (d)after testing if desired earth resistance of less than 3 ohm is not obtained, the earthing will be redone at no extra cost to govt. till desired result is obtained. 146 (e)rate shall include gi strip and protection pipe of length up to 7.5m 147 s&f galvanised earth strip of size 25 x 6mm fixed on proper post insulator at the instrument end including taking down existing strip complete all as specified and directed. 148 taking down existing gi strip 25x3mm thick as earthling lead with its accessories and re fixing to wall/roofs etc. drawn in conduit/gi pipe etc complete all as specified and as directed 149 note for item no 148: unit rate is deemed to be included for old broken insulators/ clamps replace with new insulators of existing size from site and making good disturbed surfaces of floors/walls/ceiling etc complete all as directed. 150 s & f epoxy base insulators of suitable size 40mm height for fixing gi earth strip on wall/ceiling/floor/poles etc including taking down existing one complete all as specified and as directed 151 note for item no 150: quoted unit rate deem to be included drilling holes per metre or as specified on gi/aluminium/copper strip of any type and size. 152 m & l for cutting and screwing existing gi tubing of size 20 /25/ 40mm bore for alterations or additions complete all as specified and as directed 153 supply only chemical i.e. ground enhancing compound in bag of 25 kg each complete all as specified and directed. 154 note for item no 153: material shall be delivered in the store yard of age e/m or as directed by age e/m and nothing extra shall be payable on this account. 155 s & f stop valve, cast copper alloy, screwed down, high pressure with crunch or butterfly handle screwed both ends for union and fixed for size 20mmborepipe complete including taking down existing one complete all as specified and directed. 156 repairing damaged earth pit cover factory made earth chamber in cement concrete 1:3:6(20mm stone aggregate) as shown in electrical plate no. 03 of mes schedule part i and providing pre cast rcc 1:2:4 (20mm graded stone aggregate) in slab /pitcover 450x450x 50mm in size, reinforced with and including 10mm dia tmt bars @ 100mm centre to centre in both ways including funnel and cleaning the surrounding of earth pit cover and pouring salt water to improve the resistance and measuring and recording the same in presence of engineer in charge, complete all as specified and as directed. 157 s & f copper strip 20 x 3mm thick as earthing lead fixed to wall/roofs etc including taking down existing one complete all as specified and directed. 158 note for item no 157: all joints should be joined by exothermic welding or brazing. 159 m & l for brazing / exothermic welding arrangement for existing copper strip of size 32 x 6 mm / 20 x 3 mm thick completeall as specified and directed. 160 s & f test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 no. 8mm dia, 25mm long hexagonal head screw including taking down old unserviceable one, complete all as per specified and as directed. 161 s & f air termination single pointed copper rod 16mm dia and 300mm long with arrester clamp 16mm made out of brass including provision of cement concrete 1:2:4 (20mm graded stone aggregate) block 300 x 300x 300mm and necessary fixing arrangement at roof including taking down old unserviceable one, complete all as specified and as directed. 162 note for item no 161: if threaded of the rod is damaged then contractor will be responsible for cutting of thread for fixing the rod. any minor repairs/ materials is deemed to be included. 163 s & f factory made rcc 1:2:4 (20mm graded stone aggregate) in slab/pit cover 350x350x50mm in size, reinforced with and including 10mm dia tmt bars @ 100mm centre to centre in both ways, complete including taking down existing one all as specified and as directed. 164 removing existing unserviceable earthing system and supply, installation, testing & commissioning of maintenance free chemicalearthing system comprising 17mm dia copper bondedrod 3 mtr long horizontally pre welded t terminal rod with provision for connection size of 50 x 150mm long, 6mm thickness with equal space either side, with 12mm dia hole of 02 numbers each on either side of the terminal clamp with 250 microns (average) coating thickness, tested and certified by cpri india alongwith 50 kg earth energizer compound and 10 litres earth resistance reducingliquid. the earthing energizer compound and resistance reducing earthing liquid shall be tested as per iec 62561 7 read with astm g57 06, ci 3.4 a by any nabl accredited lab. the above mentioned rod shall be installed in 8 10 inch bore, 12 feet depth with a distance of minimum 3 meters between each installation. 165 the quoted rate shall also deemed to be included the following : (i)prior toinstallation of maintenance free chemicalearthing, soil resistivity test to be carried out at the location where earthingwork to be donein presence of engr in charge/je (e/m),user and the report has tosubmitto garrison engineer with recommendation of manufacturer, if required additional interconnection ofearthing (not more than 04 number of earthing) to achieve earth result less then 1 ohms. the arrangement done for soil resistivity testingandsubmission of report with recommendationdeemed to be included in the quoted rate. 166 (ii) the description/ size/ qty of items mentioned in above are for indicating only however qty/ size may vary at site condition to maintain the earth resistance 1 ohm. the contractor shall quote rate by considering all factors. 167 (iii) rateofearth energizer compound of 25 kg of 02 bags and earthresistance reducingliquid 10 litre per cane for each pit deemed to be included in the quoted rate. 168 (iv)resistivity of earth energizer compound and resistance reducing earthing liquid shall be certified by any nabl accredited lab carried out as per iec 62561 7 read with astmg57 06, ci 3.4a and the certificate of same shall be submitted by the contractor before commencement of work. 169 (v) earth enhancing material should not leach into the adjacent soil or underground water channels and its ph valve should be in neutral range complete all as specified and as directed. it should solidify when mixed with water and set like concrete. 170 (vi) copper strip of size 20 x 3 mm shouldbe fixed on proper post insulator at the instrument end ( the rate of earthing strip up to7.5 mtrs is included in the quoted rate). 171 (vii)testing of earth shall be carriedout in presence ofdepartmental and user representativeand report shall be submitted to garrison engineer duly signed by all concern. 172 (viii)earth resistance tester will be provided by the contractor.tester should be calibrated from authorised company/ lab. 173 (ix)earthing shall be tested after completion of work by the contractor in presence of engr in charge, user and proper record shall be maintained duly signed by all concerned.after testing if the desired earth resistance of less than 1 ohm is not obtained, the earthing will be redone at no extra cost to govt. till desired result is obtained. 174 (x) the contractor shall given a written guarantee of minimum three years for maintaining the earth resistance less than 1 ohm after certified date of completion. 175 (xi) no further maintenance or periodic watering or recharge shall be required in earthing during its guarantee period of over 03 years in all type of soil including dry or rocky soil. 176 (xii) during the guarantee period, if earth resistance is not maintained less than 1 ohm the contractor has to redo or rectify at no extra cost to govt till desired result is maintained. 177 (xiii) a security deposit of value equal to 2.5 % of the rate quoted for chemical earthing per each earthing shall be retained from payment due to the contractor for the guarantee period. 178 (xiv) the electrode shallcarry manufacturers name . 179 (xv) the connection clamp shall be permanently welded to the copper bounded rod to avoid any kind of connectivity loss. the pre welded copper bounded rod shall not need any additional clamp for termination. 180 (xvi) the acceptable earth resistance at earth busbar/ test point shall not be more than 0.1 ohm. 181 (xvii)the contractor shall submit cpri india certified document for copper bonded rod to ensure genuinity of material. 182 (xviii) sign boardof mild steel 2 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxidezinc chrome primer showing result of earthing should be fixed near the earth pit after completion as directed by engr in charge. 183 (xix)earth work such as auguring andmaking good the surrounding area shall carried out in any type of soil. 184 s & f in repairs earth pit cover madeof heavy duty poly plastic of high grade polypropylene tested and certified by any nabl accredited lab for load bearing capacity not less than 9.2 tonnes with top dia not less than 250mm, bottom dia not less than 330 mm and height not less than 260 mm dia for each electrode pit complete all as specified and directed. 185 note for item no 184 : the contractor shall submit load bearing capacity certificate from the manufacturer. 186 supply and fix ip 66 thermoplastic pc gfs polycarbonate weather proof junction box size 255l x 205b x 112d mm with plain walls for cable entries to be drilled individually, system voltage : 415v, 50hz,the plain side walls on the four sides can be drilled and customized for cable entries from any direction. lid fasteners shall not have screws but shall be with quarter turn locking knobs – which is well visible ( open – locked), and they will be sealable without any accessories.cable terminal : 25 sq mm 4 no with 10a sp mcb 1 no, 6sq mm disconnected terminal 1 no, the junction box shall fulfil the following standards weather proof : uv resistant due to solar radiation, rainwater proof, temperature resistant. salt water proof & shall be suitable for off shore applications. iec 60670 22 : particular requirements for connecting boxes and enclosures. iec 60695 – 2 – 11 : flame – retardant & self extinguishing. glow wire tested at minimum 960 deg c. iec 60529 : ip 66 / ip 67 / ip 69 degree of protectionincluding taking down existing all as specified and directed. 187 taking down carefully hanger lights for repair/ replacement of defective spare parts such as ballast, etc including taking down old one of any capacity from 150 watts flame proof light including cleaning internally and externally fixing back the fitting in same position after repair and test complete all as specified and as directed. 188 note for item no 187: following shall be part of job under this item : 189 (a)the above job shall be carried out by a trained electrician 190 (b)all sort of petty t&p items such as pvc insulation table, ladder, galvanised screws, nuts, bolts, washers etc. required to accomplish the job shall be provided by the contractor with out any extra cost to dept. 191 (c) necessary t&p, safety belt, vehicle, aluminium ladder, cranes etc. shall be arranged by the contractor and cost for the same shall deem to be included in the quoted unit rate 192 (d)all safety measures and provn of all safety devices, first aid box etc shall be provided by the contractor.contractor will be solely responsible forfull safetyof the persons deployed for providing the services and department will have no liability for any type of accident/injury of any type. unit rate quoted will be deemed to include the cost of the same and no extra payment shall be made on this part. 193 supply and fix in repairs flame proof electronic led driver suitable for flame proof flood light fitting 150w sun shelter down light/ flood light fitting of make sudhir/baliga/ cg complete all as specified and directed. 194 m&l for sub main wiring with pvc insulated unsheathedfrls cable 1100 volts grade multi stranded copper conductor cable 2 runs of 4 sqmm drawn through in and including suitable size steel conduit and all accessories fixed to wall/floors along with 4 sqmm pvc insulated unsheathed copper conductor multi stranded cable 1100v grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size complete all as specified and directed. 195 note for item no 194 : (a)2 runs of 4 sqmm cable along with onerun of 4 sqmm cable for earth conductor and one run ofsteel conduit shall be measured as one length. 196 (b)connections of cables with mcbs or bus bars shall be done through appropriate size brass/copper thimbles. 197 m&l for sub main wiring with pvc insulated unsheathed frls cable 1100 volts grade multi stranded copper conductor cable 2 runs of 6 sqmm drawn through in and including suitable sizesteel conduit and all accessories fixed to wall/floors along with 6 sqmm pvc insulated unsheathed copper conductor multi stranded cable 1100v grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size complete all as specified and directed. 198 note for item no 197 : (a)2 runs of 6 sqmm cable along with onerun of 6 sqmm cable for earth conductor and one run of steel conduit shall be measured as one length. 199 (b)connections of cables with mcbs or bus bars shall be done through appropriate size brass/copper thimbles. 200 s&f switch flame proof rotary type with termination box in lm6, 16a, single pole 250v complete all as specified and directed. 201 supply and fixing in replacement of switch flame proof switch socket and plug combined in lm6 cable termination box in lm6, 16a, 250v, 2p + earth, complete all as specified and directed make : sudhir, bajaj, baliga. 202 supply and fixing in replacement of luminaire wellglass led zone i gr iic lm6 die cast aluminium lm6 housing, 230v ac, 50 hz suitable for 150w led fitting with 2 nos of 0.75et cable entry, neoprene gasket , stainless steel hardware, epoxy powder coating light grey finish shed 631/is 5 with cable gland, plug & lamp complete all as specified and directed. make cat no flpw 2595/ii c/l of sudhir, bajaj or baliga or equivalent make 203 s&f in replacement of flame proof bulk head fitting 5 w (to be used with red led bulb) including fixing arrangement all as specified and directed. 204 s&f in replacement of cable tray perforated type of size 100 x50mm made out of 1.6mm thick gi sheet fixed in peb structure by providing ms angle 40x40x5mm clamps etc including fittings like bend, tee and making good the disturbed portion and matching with existing surface complete all as specified and directed 205 s&f in replacement of flame proof weather proof vtpn distribution board 4 way 415 volts with mccb 63a , fp, 16 ka as incommer 01 no and mcb 32a tp 02 nos mcb 16a sp 18 nos as out going complete all as specified and directed.. make sudhir or bajaj, baliga or equivalent make. ...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

40427899 disposal of scrap materials available at central stores / tuticorin of tuticorin edc , sale of scrap materials available at central stores tuticorin in tuticorin edc , scrap miscellanies iron ; scrap waste paper. ; condemned 4 wheeler jeep registration tn 72 d 0918 without rc book engine no d01003248 chassis no t01001590c97 ;scrap ms / rts ; condemned lorry 5ton capacity without rc book registration tn 69 b 2434 engine no 692d22mo1237026 chassis no 358008muo202755. ; 1 scrap aaac kg 145 2 scrap aluminium incl aac cut bits kg 170 3 condemned water filter no 1 4 scrap transformer aluminium winding wire with oil insulation paper kg 1, 008 5 scrap ascr kg 1, 596 6 scrap aluminium with iron kg 1 7 scrap all aluminium alloy kg 271 8 scrap aluminium core with viper wp kg 184 9 scrap aluminium ug cable kg 881 10 scrap aluminium pvc cable kg 706 1 scrap rsj cut bit kg 1, 403 2 scrap rail pole cut bit kg 3, 168 3 condemned cash chest no 7 4 condemned computer chair no 3 5 condemnedfire extinguisher various size no 52 6 condemned 33kv vcb various operating voltage no 2 7 condemned bicycle no 1; 1 condemned shunt capacitor no 53 2 condemnedsingle phase mono black motor no 1 3 condemned three phase motor ( mono1, jet 2 ) no 3 4 condemned disk glay no 5, 242 5 condemned rhoneo machine no 2 6 condemned auto parts kg 45 7 scrap transformer lamination sheet kg 340 8 condemned single phase test bench no 1 9 condemned three phase test bench no 1 10 scrap t & p kg 147 11 scrap brass kg 150 12 scrap deal wood kg 829 13 condemned fan without regulator no 12 14 scrap brass with iron kg 21 15 condemned exhaust fan no 2 16 scrap copper with steel iron mixed kg 101 17 scrap ethernet switch n0 1 18 scrap teak wood kg 299...

Military Engineer Services - Tamil Nadu

40426653 tender for special repairs to certain bldgs and communityhall ( p 75 ) at afac coimbatore; 1 removal of plants / shrubs grown on walls / slabs / beams by making holes or demolition of concrete etc and including applying suitable chemical for killing the roots of plants, filling of holes with concreteand making good complete all as specified and directed. 2 chipping / removing loose concrete in cloumns / beams / chajjas / roof slab etc. up to reinforcement bars without damaging the reinforcement, removing all the loose material and to make all the exposedsurface free from dust and all impurities etc complete allspecified and directed. 3 removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution reebaklens rr of fosroc / sika rust off 100 / equivalent in bostic india ltd by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush and applying anti corrosive coating to reinforcement nitozinc primer of fosroc / sika friazinc r / equivalent in bostic india ltd , all as recommended by product manufacturer. 4 providing and applying one coat of structural grade epoxy coat by brush of approved make . mixing of two components will be as directed by manufacturer .application shall be provided not more than 5 hours before application of micro concrete / polymer mortar etc complete all as specified by the manufacturer.make: nitobond ep of fosrock / sikdur 32lp / equivalent in bostic india ltd 5 providing and applying n exc 40 mm thick ( in layers of each 10mm thick ) shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar renderoc sp 40 of fosroc / sika plastocrete plus / equivalent in bostic india ltd, mixed with water in a water & powder ratio 0.18 in ceiling of roof slab / chajjas / beams / parapet walls etc.note: quoted tate is deemed to be inclusive of provideing scaffolding for working in patches upto a height of 15 mtr complete all as specified and directed. 6 surface grinding, rounding off all edges to minimum of 25mm radius andand applying nitowrap cws 230 of fosrock ( or ) sika wrap 230c, uni directional, high strength, light weight, non corrosive carbon fiber sheets of all around the periphery of pier for entitre height of pier.the frp fabric used shall be ofzero degree unidirectional fibers havingfiber density of 1.8 g / cc and shall have tensile strength > 4900 mpa ; tensile modulous > 230 gpa and ultimate elongation of 2.1%. the substrate shall be primed with nitowrap 30 epoxy primer &nitowrap 410 impregnating resin saturant shall be used for saturating the fibers.saturant used shall have tensile strength of >30 mpa; elongation > 2% ; flexural strength > 30 mpa ; tensile modulous > 2400 mpa & flexural modulous > 1700 mpa when tested as per astm d638 type i and astm d 790 & glass transition temperature > 50 deg celcius as per astm e 1356. the adhesion of the entire system ( frp sheet, saturant and primer combined ) with concrete shall be > 3.5 mpa with concrete failure as per astm d 4541.wrapping the cfrp fabric to rcc member atdesired orientation using tamping rollers to avoid any airvoids etc. and sprinkling sand over it as per direction and satisfaction of engineer in charge, etc, complete. product used shall have ce ( ce 29842 ) marking and compliance according to construction products directive 89 / 106 / eec ( cpd ) 7 demolition of rcc roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work . 8 m&l for flat form work for rough finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup ports, overhangs, etc. also splays between floors and beams, etc. 9 m&l for flat form work for rough finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) . 10 m&l for rcc m 25 in beams, cantilevers, bressummers, lintels over 1.5m span 11 m&l for rcc m 25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like 12 s&f mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips 13 all as above item but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 14 taking down existing roof treatment includingscreed bed , app membrane etc upto mother slab of roof and cleaning with wire brushe and water complete , including shifting of mulba from roof to ground floor for futher disposal all as specified and directed by e i c. 15 m&l for pcc 1:1.5:3 type b0 admixed with nitobond sbr of fosrock ( or ) equivalent products in sika / asain paints @ 2% by weight of cement in roof slabs for filling up spots of loose screed / concrete , complete all as specified and directed by e i c. 16 supply and application of single component, seamless, spray applied, hybrid elastomeric pu based material i.e nitoproof 725 of fosroc chemicals ( or ) sikalastic 590 of sika india pvt ltd ( or ) equivalent in any approved make as approved by ge over a coat of primer i.e nitoproof wb primer of fosroc chemicals ( or ) diluted sikalastic 590 of sika india pvt ltd ( or ) equivalent in any approved make as approved by ge, all as recommended by manufacturer ans as specified.note: ( i ) average minimum dftof pu based material shall be 1mm and shall be applied by using a graco pump. ( ii ) pu based material shall process the following properties solids by volume 65%, tensile strength astm d412 1.75mpa, density 1.3 g / ml, elongation astm d 412 350%, adhesion to substrate concrete 1.9mpa, resistance to water 10m pressure. ( iii ) rate are deemed to be include for cleaning and preparation of surface to receive pu water proofing system including filling of cracks with cementitious repair mortars i.e renderoc cs of fosrock chemicals ( or ) equivalent of approved make. ( iii ) work shall be got carried out by authorised applicator of the manufacturer and it shall be got approved by the ge before progressing the work. ( iv ) 10 years of guarantee shall be provided and security amount shall be deposited as speicified in tender documents. 17 taking down cement plaster on brick or stone walls, ceilings, etc including racking out joints, hacking for key, scrubbing down with water, etc 18 m & lrendering in cm 1:3, 5mm thick on fair faces of brick work or concrete surfaces on ceiling complete all as specified. 19 m & l for preparation of newlyplastered surfaces and applying threecoats of white washon ceiling.surface all as specified. 20 m&l for rendering with wpc in cm 1:4, 15mm thick on othe thanfair faces of brick work or concrete surfaces all as specified and directed. note : wpc shall be measured and paid separately 21 m&l for rendering in cm 1:6, 10mm thick on fair faces of brick work or concrete surfaces all as specified and directed. 22 m & l preparation newly plasteredof wall surfaces and applyingtwo coats of cement base paint over a coat of primerall as specified and as directed directed by engr in charge. 23 m & l prepation of newly plastered wall surfaces and applyingtwo coats of distemper oil emulsion over over a coat of primerall as specified and as directed directed by engr in charge. 24 supply only intergral waterproofing compound 25 preparation of old treatedof wall surfaces and applyingone coat of cement base paintall as specified and as directed directed by engr in charge.note: ( i ) this item of work shall be executed upto a height of 30 mtr height buildings / structures / rcc ohts. ( ii ) scaffolding required to be done for executing the work above the normal heights as specified in ssr pt ii shall be measured and paid separately under a separate item for the whole building / structure. 26 m & l for applyingone coats of distemper oil emulsion on old treated / decorated surfaces of wall including preparation of wall all as specified and as directed directed by engr in charge. 27 m & l for preparation of oldplastered surfaces and applying twocoats of white washon ceiling.surface all as specified. 28 m & l for preparation of oldtreated wall surfaces and applying twocoats of white washall as specified. 29 preparing old surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint. 30 preparing old surface of steel and steel based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint. 31 providing & fixing double steel scaffolding system ( cup lock type ) on the exterior side of the building / structure, including additional rows of scaffolding in stepped manner as per requirement at site, made with 40mm dia ms tube, placed 1.5mtr c / c ( maximum ) , horizantal & vertical ms tubes jointed with cup & lock system in the scaffolding for working platform etc amd maintaining it in a serviceable condition for execution of work and removing it thereafter. the scaffolding system shall be stiffned with bracings, runners, connecting with building etc wherever required to ensure safety of workmen all as directed by engr in charge.note: 1.area derived by multiplying the outer most external perimeter and height of the building / structure shall be measured for payment.2. the payment shall be made only once after completion of all external items of work w.r.t the building / structure. 3. after completion of the work the material of the scaffolding shall be the property of the contractor and required to be removed from the site. 32 demolition of concrete in above ground floors and pavings exc 15 cm thick 33 dismantling floor, hearth or wall tiling including cement mortor bedding ( but not backing to stone and rubbish off the premises complete all as specified and directed. 34 m & l for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 35 m & l for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 36 m & l glazed coloured ceramic tilesin vertical surface 350x250x7mm / 450x350x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by engr in charge.. 37 m&lfor screed bed or bedding layer of mortor 15 mmthick in cm 1:6 for laying floor finishes all as specified and directed. 38 m&l for rendering 10mm thick on fair faces of brick work or concrete surfaces with cm 1:4as in backing coat of skirting / dado all as specified and directed. 39 m&l for brick work with sub class b bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed. 40 demolition of brickwork or stone / boulder masonry, built incement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles 41 taking down chowkhats or frames with shutter ( with out taking off the shutters from the frames ) size not exc 1.50 sqm each and all as specified and directed. 42 taking down shutters of any descriptionexc 1 sqm and n exc 2sqm each all as specified and directed. 43 s&f iind class hard wood , 35mm thickplain, framed, panelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers all as specified and directed. 44 s&f iind class hard wood, 35 mm thick glazed and skeletonshutter, open rebated and prepared to receive glass , gauge, etc without sash bars but divided into squares, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in ssr part i section 8, clause 8.24 ( a ) and fitted to chowkatscomplete all as specified and as directed by engineer in charge. 45 s & f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified and as directed by engineer in charge. 46 s & f factory made solid pvc moulded door shutter with wood eps, 30mm thick , with 2, 4, or 6 raised panel design with 2mm thick mouldedprelaminated pvc sheet on both facessupplying & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by engineer in charge. 47 steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded . 48 ditto, but without glazing bars 49 s&f mild steel work in hold fasts etc and similar work conforming to fe 290 gde e 165. 50 preparing surfaces of wood and wood based materials, steel and iron work , new or old , treating small articles such as stop, covers gully gratings, hold fasts ends of posts, back of chowkats etc , area n exc 0.1 sqm each and treated with tar or coal tar black paint. 51 m&l for cement concrete type b1 1:2:4 ( 20mm graded aggregate ) for fixing of hold fast, including finished to match with exiting surfacesall as specified and directed. 52 s&f iind class hard wood, small fittings such as shaped door and window stops and like articles n exc 200 cu cm each all as specified and directed. 53 s&f300mm long aluminium alloy, anodised sliding door bolt with hasp, staple ( bolt type ) and fixing bolts and sliding bolts of extruded sections or cast aluminum alloycomplete and all asspecified and directed 54 s & f floor door stopper 140mmlong with cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring. fixed in floor 55 s&f100mm long butt hinges, medium weight, coldrolled mild steel and all asspecified and directed 56 s&f 150mmaluminium alloy , anodised, sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy all as specified and as directed. 57 s&f 150mm longaluminium anodised barrel towers bolts of extruded section and all asspecified and directed 58 s&f 150mm extruded aluminium alloy handles, fabricated type anodised asspecified and directed 59 m&l for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces all as specified and directed. 60 framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 61 m&l for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces all as specified and directed. 62 supply only3 mm figured glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 63 supply only stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples. 64 s&f in repair only4mm sheet glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 65 s&f in repair3 mm figured glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 66 s&f in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples. 67 taking up or down steel tubing and connections, and removing to store for taking in account of credit for 15mm bore complete all as specified and directed. 68 all as per itemabovebut for 20 mm bore 69 3 layer pp r ( polypropylene random copolymer ) concealed pipes / un concealed pipes sdr 7.4 ( pn 16 ) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all pp r plain and brass threaded poly propylene random fittings fixed complete to walls / ceilings or laid on floors of 16mm outer dia of pipe all as specified and as directed 70 all as per item no 69 above but 20mm dia 71 taking down & refixing ppr 15mm / 16mm pipes 72 taking down & refixing ppr 20mm 73 s&f in repairs vitreous china wash down water closet pan ( pedestal pattern ) , white including seat cover and flush pipe etc complete all as per specified and as directed by engineer in charge. 74 s & f in repairs pvc valveless, syphonic action type, flushing cistern of 10 ltrs capacity , low level , white, with inlet , ball valve, float and handle including brackets and flush pipe etc complete all as specified and as direted by engineer in charge. 75 s& f in repair vitreous china wash basin, white, flat back, size 450x300mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including 32mm ptmt waste cupling , complete all as specifed and directed. 76 s&f in repairs bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. 77 s&f in repairs two way bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. 78 s&f in repairs pillar taps fancy type cast copper alloy, with capstain head, chromium plated screwed down high pressure, with long shanks and fly nuts screwed for iron pipe and fixed 15 mm bore. 79 s & f pvc connections 15 mm size with ptmt nuts of length 450 mm 80 s&f in repairs chromium plated angle valves, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size. 81 s&f brass chromium plated health faucet with hand held and spring operated control valve with pvc flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe. 82 m & l 75mm dia for pvc ( swr ) multi floor trap ofwith grating including jointing with solvent cement etc complete, 83 s & f in repairs 110mm dia pvc ( swr ) pipe single sockted in any length with rubber ring joints fixed to wallwith clamp complete all as specified and directed. 84 s&f 110mm radius pvc ( swr ) bendscomplete all as specified and directed. 85 s&f 110mm radius pvc ( swr ) branch piece, single ( single t ) equal or unequal complete all as specified and directed. 86 s & f in repairs75mm dia pvc ( swr ) pipe single sockted in any length with rubber ring joints fixed to wallwith clamp complete all as specified and directed. 87 s & f 50mm diaunplasticised pvc pipe of pressure rating 10 kgf / cm2 fixed complete to walls, ceiling or in floors etc complete 88 m & l for 125 / 110mm dia pvc ( swr ) gullytrap including setting jointing with solvent cement etc complete, 89 s&f 110 mm borepvc ( swr ) vent cowl 90 s&f 600mm x 450mm bevelled edge looking mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed towooden plugs with chromium plated brass screws and cup washers. 91 dismantling of pvc water tank 500 ltr capacity and removing to store 92 s&f moulded polyethylene 500 ltr water tank storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position complete all as specified and directed by engr in charge. 93 s&f in repairs 25 mm ball brass valves, high pressure, with polythene float and flynut cimplete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 94 m&l for cement concrete type b1 1:4:8 ( 20mm graded aggregate ) in filling and mass concreteall as specified and directed. 95 m&l forsand cushioning under floor or in foundation including watering and consolidation for laying of interlocking pavour block. 96 machine pressed precast concrete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness, m 35 grade with grey cement and no pigments 97 removalof debris / building material out side the campus including loading and unloading, etc to a distance exc 5km but n exc 10 km out side the md land complete all as specified and directed. note: location and permission of depositing the building materials / debris disposal outside the md land shall rest with contractor at his own arrangement. 98 taking down chain link fencing including ms straining rods and ms flat iron strips all as directed by engr in charge 99 fixing only chain link fencing including line wires any mesh size and type of standerds rails scraining babs etc incl permission o binding wire ( note supply of chain link will be measured seperately ) . 100 supply only chain link ms galvanized fencing of any mesh size and type note fixing shall be measured under serial item no here in above. 101 m& l hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencingincluding cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets ( for securing wire mesh etc. ) including all necessary drilling, bolting or riveting, etc., and similar work conforming to fe 290 gde e 165 102 tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to fe 290 gde e 165 103 dismantling wrought iron or mild steel work of any description not otherwise provided for 104 demolition ofcement concretein below or above ground level and paving not exc 15 cm thickness 105 m&l 25 mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in sub base of floors without extra cement all as specified. 106 s& f heavy duty virtified tiles 300x300mmx10mm in flooring all as specified and as directed. 107 s& f heavy duty virtified tiles 300x300mmx10mm in skirting / dado as specified and as directed. 108 m & l non skid coloured ceramic floor tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface. 109 m&lbrick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius built in cm 1:6 with old size bricks 110 m&lbrick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius in half brick thick walls built in cm 1:6 with old size bricks 111 m & lrendering in cm 1:6, 10mm thick on fair faces brick or concrete surfaces finished even and smooth without using extra cement 112 m & l prepation of newly plastered wall surfaces, apply 3mm thick wall care putty and applyingtwo coats of distemper oil emulsion over a coat of primerall as specified and as directed by engr in charge. 113 m&l for preparation of old surface and applying one coat of white wash on ceiling surface all as specified and directed . 114 s&f sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connection union to pipe, overall size 915x460mm bowl size 410mmx330mmx160mm complete all as specified and directed. 115 hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames of stone, concrete or brick surrounds, glazed with putty or fixed with beads. 116 s&f sheet glass, ordinary quality 4mm thick and glazing with oil putty or fixed with beads in square n.exc 0.5 sqm in each pane. 117 taking down shutters of any description n. exc 1.00 sqm each all as specified and directed. 118 taking down chokhats or frames with shutters ( without taking off the shutters from the frames ) size exc 1.50 sqm but n exc 4 sqm all as specified and directed. 119 s & f for second class hard wood with plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints 120 supply only4mm sheet glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed. 121 s & f butt hinges medium weight cold rolled mild steel, and fixed 75 mm size 122 s&f 100mm long extruded aluminium alloy handles, fabricated type, anodised and all asspecified and directed 123 s&f 200mm longaluminium anodised barrel towers bolts of extruded section and all asspecified and directed 124 removing buildingmaterialout side the campus including loading and unloading etc., to a distance exc 5.0 km but not exc 10.0km out side the md land ( ministry of defence ) where responsibility regarding place of deposition and obtaining permission from all authorities etc., in this regard will be of contractor responsibility and allas specified. 125 s & f pvc ( swr ) pipe 75mm diasingle sockted in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 126 s & f pvc ( swr ) pipe 110mm diasingle sockted in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 127 s&f 20mm bore gun metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed. 128 s&f soap dish ( poly carbonate ) complete all as per specified and as directed by engineer in charge. 129 s&f in repairs 125mm dia shower rose brass chromium plated with or without seivel joints, including fixing to steel pipe or union complete all as specified and directed. 130 s & f factory made solid panel pvc door shutter 30mm thick ( style ) consisting of frame made out of m.s tube for top & bottom rails. m.s frame shall be covered with heat moulded plain colour pvc c channel having pvc sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour pvc sheet for top rial, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the m.s frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement , suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by engineer in charge. 131 m & l for cement concrete type c1, 1:3:6 ( 20mm graded stone aggregate ) 75 mm thick as in plinth protection including necessary form work as required. 132 m & l for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub structure to a depth of 300mmincluding excavating channel along the wall and rodding etc. complete all as specified and as directed by engr in charge. 133 dismantling of asbestos cement ( corrugated, semicorrugated, etc. ) sheets in roof coverings 134 s & f pre painted galvalume aluminium zink coating gi based corrugated steel sheet 0.50 mm thick of any color having tensile stregth of 550 mpa as in roof covering / cladding fixed to walls fixed with self tapping screws as specified. 135 m&l for pcc 1:2:4 type b0 in roof slabs ( average thickness 50mm ) using water proofing compound complete all as specified and directed by e i c. note : wpc shall be measured and paid separately 136 m & l precast cement concrete 1:2:4 type b1 using 20 mm graded stone aggregate as in cover slab of manhole, drain cover, chullah, water troughs water troughs, shelves etc similar work with plain faces and set in cm 1:4 complete all as specified and directed. 137 s & f rolled mild steel work in tubular trusses including special shaped washer etc.complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st 240. 138 s & f roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc to fe 410 w ( gde e 250 ) quality a 139 dismantling ceiling boards any description any thickness including cover fillets all as specified and directed 140 s&f anodised aluminium snap grid frame work for false ceiling all as specified 141 s&f exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid ( frame work for ceiling shall be measured and paid separately ) . 142 s&f hangers 6 mm dia. g.i. ( upto 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 143 m & l for granite ( of any type ) tiles 20mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement withadmixture of pigment to match the shade of granite stone including 15mm thick screed bed or bedding layer of in cm 1:6all as specified and as directed. 144 m & l for 18 mm thick veneered decorative plywood, grade 1 ( with bwr resin ) with decorative face veneers on both faces; fixed with screws to timber frame work etc complete all as specified and as diirected. 145 s&f continous ( piano ) hinges 30mmwidth mild steel, bright finish or electrogalvanised complete all as specified and directed. 146 s&f 100 mm long hasp and staple, aluminium anodised, inclufing bolt to hinge plate and fixed with screw complete all as specified and directed. 147 m&l hardcore with broken stone or boulders of gauge not exc 63 mm deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surface . 148 m&l for chequered cement concrete tiles 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigmentin floors including 20 mm thick screed bed or beding layer in cement mortar 1:6 complete all as specified and as directed by engineer in charge. 149 m&l pcc 75 mm thick , type d21:4:840 mm graded aggregate as in sub base 150 supply and fixing factory made upvc white colour three track three panels sliding window with fly proof ss wire mesh ( two nos glazed & one no. wire mesh panels ) upto 1.50m height made of ( big series ) frame 116x45mm & sash 46x62mm both having wall thickness of 2.3+ 0.2mm and single glazing bead / double glazing bead of appropriate dimension. ( area of window above 1.75 sqm ) comprising of upvc multi chamfered frame, with inbuilt roller track and sash extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to upvc profile ) , appropriate dimension of upvc extruded glazing beads and upvc exruded interlocks, epdm gasket, wool pile, zinc alloy ( white powder coated ) touch locks with hook, zinc alloy body with single nylon rollers ( weight bearing capacity to be 40kg ) , gi fastners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. profile of frame & sash shall be mitred cut and fuson welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as specified and directed by engineer in charge. ( glass or wire mesh shall be paid separately ) 151 spply and fixing factory made upvc white colour fixed glazed window / ventilator made of ( small series ) frame 47x50mmmullion 47x68mm both having wall tickness of 1.9+ 0.2mm and single glazing bead of appropriate dimension. ( area upto 0.75 sqm ) comprising of upvc multi chamfered frame, and mullion ( where ever required ) extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to upvc profile ) , upvc extruded beads of appropriate dimension of epdm gasket, gi fastners 100 x 8mm size for fixing frame to finished wall, plasyic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fuson welded at all corners, mulion ( if required ) shall be also fusion welded including drilling of holes for fixing of hardwares and drainage of water etc. after fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as per approved drawing & direction of engineer in charge. ( glass or wire mesh shall be paid separately ) 152 taking down old unserviceable point wiring ( light, fan socket or power ) complete, including fixture and fittings such as switches, ceiling rose, pendents, regulators, sockets, light fittings etc.removing materials for keeping for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surface of walls floors etc. all as specified. 153 taking down old unserviceable submain wiring of any size including gi / copper earth continuity conductor in pvc conduit on wall / roof and making good to disturbed surfaces all as directed. 154 taking down ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custodyfor reuse at site andmaking good disturbed surfaces complete all as specified and as directed. 155 refixingonly ceiling fan with and including carrying out cleaning servicing, oiling and greasing of ceiling fans and connecting up including provision of cable from celling rose / connector to fan all as specified and as directed. 156 m& l painting of ceiling fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed. 157 disconnecting electric connection and taking down main switch / db of any size and keep in safe custody for taking credit complete and good / levelling the disturbed surfaces of wall to match with existing surface. 158 m&l for concealed point wiring complete with 1.5 sqmm single core pvc insulted frls cable 1100 volts grade multistrandedcopper conductor drawn through in and including 20mm dia pvc rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling / roof / etc including 1.5 sqmm single core pvc insulated frls cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for the following : ( a ) one light point controlled by one, one way switch. 159 ( b ) one ceiling / exhaust fan point controlled by one, one way switch. 160 ( c ) oneswitch socket outlet point 5 amps on independent board. 161 ( d ) one05 amps socket outlet pointon same board. 162 all as per item no.158 described here in before but with copper conductor cable frls, 4.00 sqmm for one 3 pin socket outlet, 15 amps and including 4 sqmm pvc insulated copper conductor cable as earth continuity conductor on independent board. 163 note for item no. 158 &159 : cutting chases and making good in wall / floor will be measured and paid seperately. 164 supply and fixing led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.make havells / bajaj / crompton 165 supply and fixing led light fitting mirror type withhigh out put diffuser 2 feet, 10 watt 220 v acdecorative type with driver holder and led lampincluding connecting up with three core flexiblecopper conductor cable of suitable size complete.make havells / bajaj / crompton 166 s & f led light fitting 1x9w / 1x10wbulkheadluminaires including led light driver holderconnecting up with three core flexible copperconductor cable of suitable size.make havells / bajaj / crompton 167 supply and fix mcb db, spn, 8 ways, isolated neutral bar with single doorip54 protection, door earthing arrangement with cement spill protector, mechanical impact strength ik09 complete. make: l&t / legrand / havells 168 supply and fix mcb spn 32 amps, 240volts, 10 ka, b curve complete. make: l&t / legrand / havells 169 supply and fix mcb sp 6 to 32 amps, 240volts, 10 ka, b curve complete. make: l&t / legrand / havells 170 supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals. 171 s&f modular fan regulator step type 120 w, 2 module complete all as specified and as directed. 172 s&f switch modular 6a single pole, one way, 1 module complete all as specified and as directed. 173 s&f switch modular 16a single pole, one way, 1 module complete all as specified and as directed. 174 s&f socket, 6a 2 / 3 pin combined 2 module complete all as specified and as directed. 175 s&f socket 6a / 16a 2 / 3 pin combined 2 module complete all as specified and as directed. 176 m&l for concealed sub main wiring by making recess in wall / surface complete with 2 runs of 6 sqmm single core pvc insulated frls cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 sqmm single core pvc insulated frls cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid pvc conduit and conduit accessories suface / concealed in wall / ceiling etcfor three phase sockets all as specified and as directed by engr in charge. note : 2 runs of 6 sqmm, + 1 run of 6 sqmm ( earth cotinuity conductor ) and 1 run of pvc conduit shall be measured as one unit length. 177 m & l earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 m below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead gi wire 4mm dia ( 8 swg ) connectd to gi earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board / feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and20mm bore medium grade gi pipewith funnel and wire mesh for watering including necessaryexcavation and earth works. pcc chamber in cement concrete 1:2:4 type b 1 & rcc cover and all as shown in electrical plate no. 3 of ssr ( part i ) of 2009. ( i ) the unit rate includes earthing wire, and protection pipe upto 7.5 metre. 178 cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; andcutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth 179 m& l for making opening for fixing of exhaust fan of size 300 mm sweep complete and making good the disturbed surface complete. 180 supply and fix exhaust fan, steel bodyac single phase. 230v of size 300msweep with, blades, and frame andlouvers 181 supply and fixing wall mounted fan 400 mm sweep, high speed, single phase, 230 volts , 50 hz complete. make havells / crompton / bajaj....

Southern Railway - Tamil Nadu

40420859 supply of dj close boards aluminum alloydj close boards aluminum alloy,supply of dj close boards aluminum alloy sheet/ss retro reflective type of size 800*400*2 mm as per rdso spec eti/ohe/33 a (12/97) rev.8 and annexure a drawing (attached). [ warranty period: 30 months after the date of delivery ] => limited...

Power Grid Corporation Of India Limited - Tamil Nadu

40304388 bids are invited for gym and sports equipments 3 hp motorised treadmills , aluminium alloy table tennis table , table tennis rackets 100 105 , table tennis ball white , pvc blue swiss gym ball size 55 cm sgb 001 , mild steel ped o cycle 1 year warranty , iron flat gym bench warranty 12 month , double twister one standing and one sitting , rosewood carrom board , wood chess board , high modulus graphite frame wood handle badminton racquets , volleyball blue synthetic leather volleyballs , hand stitched football , tennikoit ring smooth , 1101 1200 gram english willow cricket bat , synthetic leather red cricket ball , polypropylene full face cricketer helmet, size large , pvc printed full finger cricket gloves, size l keeper , polyurethane printed full finger batsman cricket gloves, size m , polyvinyl chloride pvc sports thigh pads , pu leather sports batsman leg pads , pu cotton cricket hand guard, size medium , synthetic leather white cricket ball , blue nylon 18.3 meter cricket net total quantity : 71...

Indian Army - Tamil Nadu

40284128 bids are invited for 1 cb / 8455 000527 armlet mp 2 cc2 / 8465 000142 container soap plastics 3 ch / knd / niv / cl2 / 242 overall comb disp w / patt indian a / l s1 4 cc2 / 8405 004534 shirt men angola drab p / wool 73 patt s / 2 5 cn / knd / niv / cl2 / 114 tin mess alluminium alloy total quantity : 11478...

Integral Coach Factory - Tamil Nadu

40227487 supply of trolley for train settrolley for train set,technical specification of trolley 1) trolley made of high grade aluminium extrusion profiles, sheets and stainless steel hardware. 2) trolley body adopts the box type sealing structure, which has thermal insulation effect 3) the inner plate is fully formed and easy to clean 4) the trolley is light weight and easy to handle 360 degree rotatable. 5) the trolley will have provision to place 3 tray in a row and 15 rows which can accommodate 45 trays 6) both side 270 degree openable door with suitable hinges and magnetic stopper 7) handle material will be of aluminium extrusion profile 8) built in door lock with handle will be made of stainless steel 9) brake mechanism made of aluminium alloy, stainless steel, and moulded nylon parts, centralized locking & unlocking on both sides. 10) 3 twin wheel with ball bearing for smooth movement 11) it has a built in door lock with handle made of ss304. 12) trolley size: 728mm (l) x 318mm (w) x 1120mm (h) 13) trolley weight: 23 26kg 14) trolley material: aluminium special alloy 15) loading weight: 150kg 16) inner size: 700mm (l) x 292mm (w) x 940mm (h) 17) packing size: 820mm (l) x 390mm (w) x1170mm (h) 18) tray size 287mm l x 225min w the schematic drawing of trolley is enclosed as annexure i note: successful tenderer shall submit oga drawing for approval to icf before manufacture. [ warranty period: 30 months after the date of delivery ] => limited...

Military Engineer Services - Tamil Nadu

40226152 tender for provision of certain sanctioned and major revenue works at af station sulur; 2 surface excavation n.exc 30 cm deep and averaging 15cm deep in soft / loose soil complete all as specified and as directed. 3 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying xlpe cable etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard / dense soil complete all as specified and as directed. 4 m&l pcc ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. 5 m&l reinforced cement concretetype b 0, 1:2:4 using 12.5mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. 6 m&l formwork to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc to provide flat rough finished concrete surface complete all as specified and as directed. 7 m&l reinforced cement concrete type b 0, 1:2:4 using 12.5mm graded stone aggregate slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed. 8 m&l formwork to soffits of suspendedslabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) to provide flat rough finished concrete surface complete all as specified and as directed. 9 m&l formwork toedges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide to provide flat rough finished concrete surface complete all as specified and as directed. 10 m&l reinforced cement concrete type b 0, 1:2:4 using 12.5mm graded stone aggregate as in chajjascomplete all as specified and as directed. 11 m&l formwork to chullah hoods, chajjas, troughs and similar items including edges to provide flat rough finished concrete surface complete all as specified and as directed. 12 s&f high strength corrosion resistant tmt steel bars of grade fe–500of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 13 s&f high strength corrosion resistant, tmt steel bar of grade fe 500, 5 mm dia and above and up to 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire ( annealed ) not less than 0.9 mm dia., or securing with clips in stirrups , spacers and binders etccomplete all as specified and as directed. 14 m&l100 mm thick pcc ( 1:4:8 ) type d 2 using40 mm graded stone aggregate as in sub base floors complete all as specified and as directed. 15 m&l 25mm thick cement concrete type b 1, 1:2:4 using 20mm graded stone aggregate as in floors complete all as specified and as directed. 16 m & l pre cast cement concrete block masonry with solid blocks, type c 1, in pcc 1:3:6 using 20 mm graded aggregate, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed. 17 m&l rendering 10mm thick on brick work or concrete surfacesin cementmortar 1:4 and finishedeven and smooth without using extracement complete all as specified and as directed. 18 m&l preparation on newly plastered wall surfaces and applying two coats of oil bound distemper over the wall treated with 2mm thick plaster of paris putty and one coat of alkali resistant primer complete all as specified and directed. 19 m&l rendering 15 mm thick onbrick or concrete wall surfaces, in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. 20 m&l preparation on newly plastered wall surfaces and applying two coats of cement base paint one coat of alkali resistant primer complete all as specified and directed. 21 m&l 75mm thick, plain cement concrete ( 1:3:6 ) , type c 2 ( using 40 mm graded stone aggregates ) , as in plinth protection / path including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling ( to full depth ) comprising of one part heated hot blown bitumen 85 / 25 & two parts heated sand ( by volume ) , surface finished even and smooth without using extra cement, complete all as specified and as directed. 22 note for item no 21 : the concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm. 23 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. 24 removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed complete all as specified and as directed. 25 m&l framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 complete all as specified and as directed. 26 m&l preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. 27 note for item no 26 : ( a ) all synthetic enamel paint, shall be of 1st quality manufactured by the standard firms of make as specified. 28 ( b ) the contractor shall inform the ge, within three weeks of the acceptance of the tender, the brand / names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of ge before their use in works. 29 ( c ) the contractor shall when so required by the ge, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant indian standards. tint of paint, will be approved by the ge. 30 ( d ) paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. the paint so procured shall be of first quality of any approved make as per list of makes specified. i. berger paints ( luxol ) , ii. jenson & nicholson ( brolac ) , iii. shalimar paints ( superlac ) , iv. goodlass nerolac ( nerolac ) , v. asian paints ( apcolite ) 31 ( e ) unless otherwise specified the tints of paint shall be as approved by the ge 32 ( f ) the contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the engineer in charge for approval. 33 ( g ) the surface shall be thoroughly cleaned and dusted. all dirt scales oil and grease shall be thoroughly removed before painting is started. the prepared surface shall be inspected and approved by the ge before painting is commenced. the weather shall not be foggy / rainy, dusty or windy. the suitability of the weather will be determined by the engineer in charge. 34 ( h ) no hair marks from the brushor clogging of paint buddles shall be left on the work. surface shall ordinarily not be painted until it has dried up completely. trial patches of paint shall be laid at intervals to check if drying is satisfactory. 35 ( e ) unless otherwise specified the tints of paint shall be as approved by the ge 36 ( f ) the contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the engineer in charge for approval. 37 s& f steel rolling shutterswith out ball bearing, springas per specified including top cover, anchoring rod, hasp and staple withone shop coat of primerand two coats of synthetic enamel paint with gear operated box ( approved quality ) erected in position and making good the surface after fixing including locking system complete all as specified and as directed . 38 s&f pre painted coloured corrugated galvalume roofing system sheet 0.50 mm thick having zinc aluminum alloy coating az150 shall be as per is:277 / astm 1379 150 gsm / sqm double ribbed trapezoidal profile steel sheetany colour having tensile strength of 550 mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified anddirected. 39 m&l pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mmthick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified anddirected. 40 note for item no 38 & 39: ( pre painted coloured galvalume roofing ) : 41 ( i ) the manufacturers test certificate andindividual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation. 42 ( ii ) the contractor shall ensured that no leakages take place from the roof. the roofing shall be coloured galvalume roofing system ( olive green colour or as approved by ge ) with feed material manufactured from 0.50 mm totalcoated thickness ( tct ) , minimum 550 mpa yield strength and shall conform to the physical specifications of is: 2062 of 2011, coated with hot dip metallic aluminium / zinc alloy coating az150 as 150 gm / sq.mt total on both sides. 43 ( iii ) the painting shall be coloured baked enamel polyesterwith silicon coatingoffilm thickness 25 microns nominal on the exposed face / exterior side and on the reverse side ( interior face ) shall be white with 15 microns film thickness, over a coat of 5 micron nominalthickness primer. 44 m & l aluminium powder coated ofthree track sliding window consisiting of outer frame top & sides ( section no 20831 ) of size 92.0x31.75x1.5mm weighing 1.06 kg / m, frame bottom ( section no 20832 ) of size 92.0x31.75x1.5mm weighing 1.248kg / m , shutter to plain vertical ( section no 21093 ) of size 39x18x1.5mm weighing 0.634 kg / m, shutter interlock vertical frame ( section 21094 ) of size 39x18x1.55 weighing 0.734 kg / m, shutter bottom horizontal frame ( section no 20551 ) size 40x20x1.5mm weighing 0.484 kg / m, with powder coating of min thickness 50 micron , sliding type with out sash bars, including 4mm thickness colour glass, rubber packing, snap beading screws with stainless steel wire mesh, complete all as specified anddirected. 45 note for item no 44 : the minimum thickness of powder coating shall be 50 micron 46 m & l damp proof course 40 mm thick, in plain cement concrete1:2:4, type b 0, using 12.5 mm graded stone aggregate including necessary formwork complete all as specified and as directed 47 m&l 150 micron thick, polythene film laid over a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm complete all as specified and directed 48 s&f steel work in tubular trusses and columns including special shaped washer etc complete using erw or induction butt, welded tubes conforming to is 1161 1979 grade st 240complete all as specified 49 s&f framed brackets of angles or tees with web and flanges, cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary , gusset plates, riveting, etc. n exc10 kg each brackets, conforming to fe.290.gde e 165complete all as specified 50 s&fplates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, with riveted , bolted or welded attachment. ( fe 410 w ( gde e 250 ) quality a complete steelall as specified 51 s&f ms flat iron wind ties for roof including securing bolts and all necessary drilling, bolting or riveting, etc. , and similar work conforming to fe 290 gde e 165 all as specified and as directed. 52 s&f mild steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, n exc 5cm long diameter of neck 5 to 10mm complete all as specified and directed. 53 m&l preparation of new steel surface of any description n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. 54 note for item no 53 : ( a ) all synthetic enamel paint, shall be of 1st quality manufactured by the standard firms of make as specified. 55 ( b ) the contractor shall inform the ge, within three weeks of the acceptance of the tender, the brand / names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of ge before their use in works. 56 ( c ) the contractor shall when so required by the ge, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant indian standards. tint of paint, will be approved by the ge. 57 ( d ) paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. the paint so procured shall be of first quality of any approved make as per list of makes specified. i. berger paints ( luxol ) , ii. jenson & nicholson ( brolac ) , iii. shalimar paints ( superlac ) , iv. goodlass nerolac ( nerolac ) , v. asian paints ( apcolite ) 58 ( e ) unless otherwise specified the tints of paint shall be as approved by the ge 59 ( f ) the contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the engineer in charge for approval. 60 ( g ) the surface shall be thoroughly cleaned and dusted. all dirt scales oil and grease shall be thoroughly removed before painting is started. the prepared surface shall be inspected and approved by the ge before painting is commenced. the weather shall not be foggy / rainy, dusty or windy. the suitability of the weather will be determined by the engineer in charge. 61 ( h ) no hair marks from the brushor clogging of paint buddles shall be left on the work. surface shall ordinarily not be painted until it has dried up completely. trial patches of paint shall be laid at intervals to check if drying is satisfactory. 62 ( e ) unless otherwise specified the tints of paint shall be as approved by the ge 63 ( f ) the contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the engineer in charge for approval. 64 m&l hardcoreofgaugenotexceeding 63mmofbroken stonesorboulders, deposited, spreadandlevelledin layersnotexceeding 15cmthick, wateredand rammed to a true surface completeall as specified and directed. 65 m&l100 mm thick pcc ( 1:2:4 ) type b 2 using40 mm graded stone aggregate as in sub base floors for receiving tiles complete all as specified and as directed. 66 m & l moorum / red bajrifilling including spreading and levelling in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. 67 m&l vitrified ceramic tiles 10 mm thick, lightshade ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding screed bed or bedding layer, 15 mm thick in cement mortar 1:6complete all as specified and as directed. 68 m&l vitrified ceramic tiles 10 mm thick, lightshade ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting / dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding backing coat with 15 mm thick in cement mortar 1:6 complete all as specified and as directed. 69 note for item no67 & 68 : ( i ) vitrified tiles are classified under group b1a of the international standard for ceramic tiles iso: 13006. tiles shall be hard, dense, impervious and frost resistant. water absorption of tiles shall be less than 0.5% and flexural strength ( modulus of rupture ) shall be more than 35 n / sqmm. 70 ( ii ) the manufacturers test certificate andindividual test certificateof tilesmust be submitted for approval by the concerned authority prior to installation. 71 s & f machine pressed rubber moulded precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to is 15658 of 80mm thickness m 40 grade, laid over and including m sand cushion of 50mm thick complete and packing the sides with pcc 1:3:6 complete all as specified and directed. 72 ( b ) the manufacturers test certificate andindividual test certificateof tilesmust be submitted for approval by the concerned authority prior to installation. 73 m&l false ceiling using gi snap grid size 60x60cm with main runner 38mmx24mm, wall angle & cross tee 29mmx24mm wall angle 24mmx24mm suspended with 4mm dia gi wire fixed with steel dash fasteners carrying max load upto 8.1 kg / sqcm including supply and fix 4mm thick designer ceiling board complete all as specified and as directed by engineer in charge. 74 m&l brickwork with subclass ‘b’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1: 4completeall as specified and directed. 75 m&l point wiring using approved colour coding as per iswith pvc insulated, unsheathed frls multi stranded copper conductor 1.5 sqmm ( nominal area ) 1100 volt grade cable for phase & neutral drawn through 20mm dia pvc conduit fixed on surface ofwall, columns etc including pvc insulated, unsheathed frls multi stranded copper conductor 1.5 sqmm ( nominal area ) copper conductor as earth wire and connected to earth dolly for the following complete all as specified and directed. 76 one light point / ceiling fan / exhaust fan / bell point controlled by one switch 77 all as per item no. 75 here in before but for one 3 pin socket out 6 ampon the same board 78 all as per sl no 75 above but wiring with 2.5 sqmm copper multistranded unsheathed cable and 2.5 sqmm copper cable for earth continuity conductor controlled by one 16a switch socket independently 79 s&ffactory madepowder coated distribution board sp & n 8 way double door, including200 amp rated bus bar, neutral bar, standard din rail, earth bar complete all as specified and conforming to is: 8623complete all as specified and directed. 80 m&l for sub main wiring with pvc insulated unsheathed frls cable 1100 volts grade multi stranded copper conductor cable 2 runs of 6 sqmm drawn through in and including suitable size pvc conduit with all accessories fixed to wall / floors along with one run of6 sqmm pvc insulated unsheathed copper conductor multi stranded cable 1100v grade as earth continuity conductor and connected to common earth dolly complete all as specified and directed. 81 note for item no 80: ( a ) 2 runs of 6 sqmm cable along with 1run of 6 sqmm cable for earth conductor and one run ofpvc conduit shall be measured as one length. 82 ( b ) connections of cables with mcbs or bus bars shall be done through appropriate size brass / copper thimbles. 83 s & f modular switch1 way 6 amp.1 module complete all as specified and directed. 84 s & fmodular switch1 way 16 amp.1 module complete all as specified and directed. 85 supply & fix modular socket outlet 6a 2 / 3 pin combined 2module, complete all as specified and directed. 86 supply & fix modular socket outlet 6a / 16a 2 / 3 pin combined 2module, complete all as specified and directed. 87 supply & fixmodular white cover plate with frame, 3 module complete all as specified and directed. 88 supply & fixmodular white cover plate with frame, 6 module complete all as specified and directed. 89 supply & fixmodular white cover plate with frame, 8 module complete all as specified and directed. 90 s & f modular metal flush box, 3 module complete all as specified and directed. 91 s & f modular metal flush box, 6 module complete all as specified and directed. 92 s & f modular metal flush box, 8 module complete all as specified and directed. 93 supply and fixing led light fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 94 s & f led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 95 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 5 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 96 supply and fixing ceiling fans with brushless direct current motor ( bldc ) , five star rated, 230v, min air delivery 210 cfm with service value 6.00 bee., 1200 mm sweep complete with blades, down rods and fittings accessories like flexible copper cord if size 1.5 sqmm etc, complete all as specified and directed. 97 supply and fix exhaust fan, steel body ac single phase. 230v of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed. 98 s&f electronicmodular fan regulator 230 volts, step type, socket type, hum free 120 watt 2 module complete all as specified and directed. 99 supply & fix single pole mcb 6 to 32 amp, 240 v, 50 hz acsuitable for ‘c’ curve, 10 ka breaking capacity conforming to is 8828 of 1996complete all as specified and directed. 100 supply & fix single pole neutral, mcb 32 amp, 240 v, 50 hz acsuitable for ‘c’ curve, 10 ka breaking capacity conforming to is 8828 of 1996complete all as specified and directed. 101 supply and fixing led street light fitting 20 watt, 230 v ac outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection complete all as specified and directed. 102 m & l for making connection of pp r distribution branch with pp r main of sizes16 to 40 mm bore by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed. 103 supply and fixing pp r gate valves ( brass insert ) 25 mm outer dia with iron wheel head screwed both ends for iron pipes complete all as specified and directed. 104 s & f 25 mm outer dia of pipes 3 layer pp r ( polypropylene random copolymer ) pipes concealed pipes sdr 7.4 ( pn 16 @ 20°c ) uv stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. all as specified and directed. 105 note for item no 104 : ( a ) the unit rate shallinclude the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accessories such as pipe hooks, screws clamps etc 106 ( b ) wall thickness of pipes shall be all as per is : 15801 107 s & f ball brass valves of size 25mm bore, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed. 108 removingexcavated material to a distance not exc. 50m and depositing where directed at level not exc 1.5 m above complete all as specified and as directed. 109 s & f rotational moulded polythene water storage tank of500 ltrs capacity cylindricalvertical with closed top including 3 nos gi check nuts and tank nipple of 25mm bore for inlet and outlethoisted and fixed in position all as specified in ssr part i including complete all as specified and directed. 110 s & f xlpeinsulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100volts grade cross sectional area 16 sqmm 4 core laid in trenches / ducts / fixed to wall / pole / inside panel / drawn through pipe including cable glands and terminal sockets complete all as specified and directed 111 m & l earthing with galvanised earth plate electrode 600x600x 6mm thick buried directlyin ground ( earth pit not less than 2.25 metre below ground level ) with top edge of the plate not less than 1.50 metre below ground level, connected with galvanised iron earth wire 4mm dia by means of bolts, nuts, check nuts and washers of gi or steel and connected earthing testing point / bus bar including gi 15mm bore ( dia ) medium grade protection pipe, earth plate surrounded by a packed thickness of char coal or coke dust mixed with common salt, magneisum sulphate ( 1 : 1 : 0.5 ) in alternate layers of not exc 150mm thick, pcc pit in cement concrete 1:3:6, type c 1 using 20mm graded stone aggregate and pre cast rcc cover slab of size 300x300x40 mm in cement concrete 1:2:4 type b 1 using 20mm graded stone aggregate, reinforced with 10mm dia tmt bars @ 100mm centre to centre in both ways, gi wire mesh, funnel with gi watering pipe 20mm bore ( dia ) medium grade including necessary excavation in any type of soil, returning, filling in and removal of surplus spoil disposal to out side md land and all as shown in electrical plate no. 3 of mes schedule part i and testing on completion etc complete all as per specified and directed. 112 note for item no 111: ( a ) all joints should be joined by exothermic welding or brazing. 113 ( b ) after completion of work earthing shall be tested by the contractor in presence of engineer in charge, user and proper record shall be maintained duly signed by all concerned. 114 ( c ) earth resistance tester shall be provided by the contractor. it should be calibrated from authorised company / lab. 115 ( d ) after testing if desired earth resistance of less than 5 ohm is not obtained, the earthing will be redone without extra cost to govt till desired result is obtained. 116 s&f factory madepowder coated distribution board vtpn, 4 way double doorincludingbus bar, neutral bar, standard din rail, earth bar completeall as specified and conforming to is: 8623 completeall as specified and directed. 117 s&f mccb four pole, 63 amp ultimate breaking capacity 16 ka, 415v including connecting by using suitable size of lugs complete conforming to iec 61439 1 complete all as specified and as directed. 118 s&f mccb four pole, 40 amp ultimate breaking capacity 16 ka, 415v including connecting by using suitable size of lugs complete conforming to iec 61439 1 complete all as specified and as directed. 119 s & f 40 mmbore gi tubinglight gradefor protection of lt cables fixed to walls / poles / road crossing including clamps and fittings complete all as specified and directed. 120 m&l fly ash bricks using modular bricks as in cable protection covercomplete all as specified and directed. 121 riddling sand obtained from excavation for cable protection 8cm under the cable and 15cm above the cable in trench and get the thick layer of 18cm after ramming complete all as specified and as directed. 122 note for item no 121 : in case sufficient sand not obtained from excavation, the required additional qty shall be obtained from out side md land as directed by the engineer in charge and the rate is deemed to be included the above provision also. 123 supply and fix in repairs to ms c track with accessories without cable of existing size and gauge suitable for 3 / 2 ton crane complete all as specified and directed.make : rockwell or equivalent approved as directed 124 supply and fix in repairs to6+2 pendent suitable for 3 / 2 toneot crane complete all as specified and directed. make: schneider or equivalent approved as directed 125 supply and fix in repairs tofeston trolley suitable for 3 / 2 ton rockwell eotcrane complete all as specified and directed. 126 supply and fix in repairs toct, lt, hoist limit switch with connected arrangements of 3 / 2 ton eot crane complete all as specified and directed. make: rockwell or equivalent approved as directed 127 supply and laying of pvc copper conductor electric flat cable of size 1.5 sqmm, 16 core on wall, floor, ceiling etc including taking down existing cable complete all as specified and directed....

Integral Coach Factory - Tamil Nadu

40192717 supply of trolley for train settrolley for train set,technical specification of trolley 1) trolley made of high grade aluminium extrusion profiles, sheets and stainless steel hardware. 2) trolley body adopts the box type sealing structure, which has thermal insulation effect 3) the inner plate is fully formed and easy to clean 4) the trolley is light weight and easy to handle 360 degree rotatable. 5) the trolley will have provision to place 3 tray in a row and 15 rows which can accommodate 45 trays 6) both side 270 degree openable door with suitable hinges and magnetic stopper 7) handle material will be of aluminium extrusion profile 8) built in door lock with handle will be made of stainless steel 9) brake mechanism made of aluminium alloy, stainless steel, and moulded nylon parts, centralized locking & unlocking on both sides. 10) 3 twin wheel with ball bearing for smooth movement 11) it has a built in door lock with handle made of ss304. 12) trolley size: 728mm (l) x 318mm (w) x 1120mm (h) 13) trolley weight: 23 26kg 14) trolley material: aluminium special alloy 15) loading weight: 150kg 16) inner size: 700mm (l) x 292mm (w) x 940mm (h) 17) packing size: 820mm (l) x 390mm (w) x1170mm (h) 18) tray size 287mm l x 225min w the schematic drawing of trolley is enclosed as annexure i note: successful tenderer shall submit oga drawing for approval to icf before manufacture. [ warranty period: 30 months after the date of delivery ] => limited...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

40186800 disposal of scrap and condemned materials available at kadamparai generation circle , lot no. 01. ( lot of fifteen items ) ( available at central stores / kadamparai power house ) 1. m.s misc. scrap 10000 kgs. 2. rail pole cut bit scrap 284 kgs. 3. ss scrap 2 kgs. 4. m.s / rts grills scrap 26 kgs. 5. t&p scrap 218 kgs. 6. condemned emmeter scrap 20 kgs. 7. condemned megger of all sizes 1 no. 8. condemned multi meter 1 no. 9. condemned printer various size 2 nos. 10. condemned window type ac 1.5 cap 2 nos. 11. condemned mercury choke 26 nos. 12. condemned emmeter 2 nos. 13. brass mixed ms scrap 2 kgs. 14. condemned cpu unit with colour monitor set 1 set. 15. condemned 250 / 11 kva unit auxilary transformer without oil 1 no. , lot no. 02. ( lot of fifteen items ) ( available at central stores / kadamparai ) 1. m.s misc. scrap 9535 kgs. 2. teak wood scrap 189 kgs. 3. tube light fitting scrap 101 kgs. 4. aluminiumscrap 29.5 kgs. 5. condemned pedestal fan 2 nos. 6. steel wire rope all size 1294 kgs. 7. pvc aluminium cable cut bit scrap 3 kgs. 8. aluminium alloy scrap 3 kgs. 9. condemned celling fanw / regulator 1 no. 10. condemned trivector meter 3 nos. 11. condemned fax machine 1 no. 12. condemned refrigerator 3 nos. 13. empty ms barrel 200 / 210 lit. cap leaky 43 nos. 14. condemned ups 0.5kva 1 no. 15. auto scrap 226 kgs....

Chennai Metropolitan Development Authority - Tamil Nadu

40151195 tender for park development at perumbakkam, chennai; 1 civil works 2 earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. 3 supplying and filling in foundation, basement, etc with filling m sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 4 supplying and filling approved river sand of specified quality for sand pits in play zone area. the rate including the cost of sand, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, loading, unloading, spreading in layer not exceeding 150 mm thick, watering, ramming, compacting with mechanical compactors and / or other equipment to specified levelall complete and as per the standard specification. 5 plain cement concrete 1:4:8 ( one cement, four sand and eight hard broken stone jelly ) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification 6 plain cement concrete 1:2:4 ( one cement two sand and ten broken machine crushed stone jelly ) using hbg machine crushed stone jelly of size 20mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. 7 supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 bg stiffened with welded mild steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. ( payment for centering shall be given after the concrete is laid ) 8 for plane surfaces such as rcc floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 9 for plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc. 10 providing and laying m 30 design mix for all reinforced cement concrete with minimum cement content conform to is 456 2000 using ordinary portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for raft, grade beam, shear wall, rcc walls, lift walls, plinth beams, column, footings, grade slab, roof slab & beam, curved slab, beam, column drops, pergola, staircase waist and landing slab lintel, sunshades, parapet cum drops, steps, canopy, window boxing slab, loft, fins facia planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items.rate to include all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in rcc slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the engineer in charge 11 basement concrete work 12 ground floor concrete work 13 providing under reamed pilesr.c.c.38 cm ( 15 ) dia cast in situ with single reamed ( bulb ) in cement concrete1:1.5:3, 11.5cm above g.l. including boring, erecting, vibrating, curing, hire charges for drilling equipments, etc., complete as per relevent isi specifications ( excluding cost steel reinforcement ) . 14 bored pile 450 mm diaproviding and installing bored cast in situ reinforced cement concrete pile ofspecified diametre and length below thepile cap in rmc m25 concrete to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including bentonite solution machinery charges labour chargres etc., all complete. ( length of pile for payment shall be measured from bottom pile to the bottom of pile cap ) 15 supplying, fabricating and placing in position mild steel / ribbed tor steel grills for all rcc works as per design given including cost of steel and g.i. binding wire in all floors etc. complete complying with standard specification. ( contractor has to make his own arrangements for the supply of steel and binding wire ) 16 brick masonry in cement mortar 1:5 ( one cement and five sand ) in foundations, basement and superstructure walls using second class ground moulded chamber burnt bricks of size 9”x 43 / 8”x2 3 / 4” etc., complete complying with standard specifications and drawings and as directed by departmental engineers 17 basement brick work 18 ground floor brick work 19 brick partition walls of 11.50cm thickness using best quality ii class ground chamber burnt bricks of size9 x 43 / 8 x 23 / 4 in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. 20 supplying and filling brick bats of size various from 20to40mm in regular layers of 15cm thick including watering, consolidating and rolling with hand roller, etc., complete as per direction of engineer in charge 21 supplying and filling in foundation, basement, etc with filling gravel inwellrammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. 22 supplying and stacking of red earth at site to the departmental guage for premeasurements which is of light textured, crystalline, porous and firable and not of generally acidic or neutral but not of alkaline and should not of alkaline and shoulde be fertile. the rate including seignior age charges, cost of red earth, transportation, loading & unloading, stacking etc., complete and as directed by engineer in charge. 23 special ceiling plastering and finishing the exposed surface of all rcc items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with cement mortar 1:3 ( one cement and three sand ) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers 24 plastering with cement mortar 1:5 ( one cement and five sand ) , 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. 25 supplying and painting of2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. the rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the engineer in charge. 26 providing granolithic floor finish 25mm thick with pcc 1:2:4 ( one cement two sand and four aggregate ) using 10 to 12mm thick hgb jelly and river sand and including rubbing the top surface smoothly thread lining if found necessary and curing etc., complete complying with standard specification and as directed by the departmental officer 27 providing and laying granular sub base ( gsb ) by provided coarse graded material confirming to ( table 400 1 ) mixing in a mechanical mix plant at omc carriage of mixed material to work site spreading in uniform layers with motor grader on prepared surface and compacted with vibratory power roller to achieve the desired dry density to the required grade and cross slope as per drawings all others incidental charges etc.complete as per clause of 401 morth specification 28 structural steel works:supplying fabricating, hoisting, erecting and fixing in position mild steel structural steel works of pergola, gate for compound wall and grill at all elevations, levels and heights including aligning, leveling, providing and fixing bolts, nuts, washers, comprising ms plates, flats, squares etc., of various sizes and other structural steel sectionsconforming to latest is2062 grade a&b including straightening, cutting, welding, bending to shape, bolting and inclusive of the following finishes. the rate including cost of all materials, labour chanrges, scafolding, stagging, transportation, lead & lifts, wastage, etc., complete with all respects complying with relevant standard specification, as directed by the engineer in charge. all ms members shall be painted with one coat of zinc chromite primer and 2 coats of 35 microns dft of synthetic enamel paint of approved colour and make etc, .the rate includes the cost of all materials, labour, tools, tackle and plants, wastage etc., as per specification and drawings complete. the rate quoted is to include cost of bolts, nuts, washers, welding, electrodes and connections required for the work. no extra on this account will be paid for. the rate to include preparation of fabrication shop drawings for owners approval: 29 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( the make quality and colour of paint should be got approved by the executive engineer before use on works. ) 30 manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304l grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. the vertical pipe has to be welded to the 100 x 100 x 6mm ms base plate encased in the base concrete. the rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 31 solid pvc door shutters using 19 gauge 19mm ms square tubes for styles and outer frames. 15mm ms square tubes for top, lock and bottom rails. the steeltubes shall be covered with 5mm thick solid pvc sheets. shutter using 5mm thick solid pvc sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. the over all size of styles shall be 50mm x 30mm. the over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. the over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutte 32 providingcountry wood wrought and put up frame for door and window any other similar joinery works using following size of upto 4m in length country wood scantling of pillai maruthu or patak including labour for wrought and putup in position etc., complete complying with standard specification.. 33 frp door suitably reinforced using ms angle / flats, cost of holdfasts and solid core frp shutter panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by engineers 34 upvc windowspecification:supplying and fixing upvc ( un plasticized polyvinyl chloride ) windows of casement type ( open ) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with gi / 1mm 125gsm and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with over all the edges of frame and shutter the shutter will be provided with espag multi power point locks and also it operates as handle. the corners and joints should be welded and cleaned. radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. the connecting mechanism between sash and outer frame that enables opening of the window. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the window should be got approved from the executive engineer before use on work 35 upvc ventilatorspecification:supplying and fixing upvc ( un plasticized polyvinyl chloride ) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with gi / 1mm 125gsm and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. the epdm rubber ( black colour ) covered with all over the edges of frame and shutter. the corners and joints should be welded and cleaned. radiations pin headed glass 4mm thick should be provided in the louvers. the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. the ventilator should be got approved from the executive engineer before use on work 36 weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime ( no sand to be used ) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the rcc roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. 37 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 38 flooring with followingdesigned antiskid ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 ( one cement and three sand ) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. ( the make and brand of the tiles should be got approved by executive engineer before use on works ) 39 dadooing walls with following best approved quality, designed colour ceramic tilesof following sizes set in cement mortar 1:2 ( one cement and two sand ) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 40 supplying and laying interlocking rubber moulded paver 83mm thk of approved sample as per design / drawing made of m40 concrete 83 mm thick includingtransportation of the blocks to the site preparation of surface including supplying and filling with manufactured sand to 50 mm thick, levelling and compacting with plate vibrator and laying of the inter locking paving blocks with sand binding and final compaction with plate vibrator of 3 tonne capacity finishing the surface including cutting of blocks at the edges including all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 41 supplying and layingmanhole cover sfrc with size of 750mm x 750mm including all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 42 supplying and laying pvc mould ci steps for sumpincluding all labour, materials, transportation, shifting etc., complete, as directed by the engineer in charge 43 supplying and fixing colour metal roofing sheets made up of galvalumed aluminumzinc alloy coated steel, az 150 and hitensile grade 550 steel of thickness 0.47mm, trapezoidal profile over all width 1080 mm etc as per direction of engineer in charge 44 supplying and fixingweld mesh of size 7.5x2.5cm 10 gaugeincluding all labour, materials, transportation, shifting, welding chargesetc., complete, as directed by the engineer in charge 45 providing and fixing 18mm thick machine cut, mirrorpolished, premoulded and pre polished machine cut granite for platforms, seating top finished copping, etc., of approved qualityfor wash basin / vanity counters, pantry etc.of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 ( 1 cement:4 m sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by engineer in charge. 46 plumbing 47 supplying and fixing in position best approved of bis quality pvc rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry pvc shoe, pvc bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the rcc roof slab including finishing neatly etc., complete. the rate shall be inclusive of cast of removable cast iron grating. the pvc pipe shall be fixed in wall with special type of u clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 48 supplying and fixing in position best quality pvc soil / waste pipes of various dia having 6 kg / sq.cm. pressure bis mark and providing leak proof joints using pvc adhesives including fixing to the wall with special pvc / ms clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / rcc works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. ( the pvc pipes should be got approved by the executive engineer before use on works ) . the rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level 49 supply and delivery and fixing of hdpe tankincluding loading, unloading, transportation and labour charges for fixing of the pipes and specials for pipe connection works including cutting, threading and fixing charges etc., 50 supplying and fixing in position first quality and approved variety of gun metal gate valve / wheel valve with bis make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements ) .the valves to be used on work shall be got approved by the executive engineer before use on work. 51 32mm gun metal gate valve 52 40mm gun metal gate valve 53 supplying and fixing in position 15mm dia brass long body tap ( heavy duty ) of approved make conforming to bis specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. ( taps should be got approved by the executive engineer before use on the works ) 54 sd tap 55 pillar tap 56 supply andlaying and jointingupvc pipe ( un plasticized polyvinyl chloride ) upvc used for commercial applications operate and designed to handle higher water pressure ( schedule 80 ) including cost of such specials and fixing in position dismantling masonry and make the same to original conditionetc complete complying with standard specification and as directed by the departmental officers at site of work. 57 25mm dia 58 32mm dia 59 supplying and fixing in position best quality and approved make indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm ( with pedestal / without pedestal ) with a pair of cast iron brackets, including cost 15mm dia brass cp pillar tap, 32mm dia b class gi waste pipe with rubber plug and chain, 15mm dia gm wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia cp brass waste coupling including fixing of wash basin using ci brackets on to the wall in position with tw plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. ( the wash hand basin and specials should be got approved by the executive engineer before use on works ) . 60 supplying and fixing in position cp shower rose with cp stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers ( the cp shower rose should be got approved by the executive engineer before use on works ) . 61 supplying and fixing in position indian make bevelled edge mirror of approved quality and brand pvc / fibre glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. ( the mirror should be got approved by the executive engineer before use on woks ) 62 supplying and fixing in position white / glazed european water closet of best quality and approved make with 100 mm p or s trap connecting with ci pipe of 100mm dia / pvc pipe of 110mm dia, double flapped rigid pvc black seat and seat cover with cp brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity pvc porcelin low level flushing tank with a pair of ci brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white pvc flush hand using indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm gm wheel valve, 15mm brass nipple ( 2 nos. ) , 15mm nylon connection, tw plugs, screws and also giving necessary connection to the pvc pipe including cost of 600mm length of 110mm dia pvc pipe and painting the ci brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re doing the dismantled masonry to original condition etc. complete complying with standard specifications. ( the ewc and flushing tank wiht all accessories should be got approved by the executive enginer before use on works ) 63 supplying and fixing position ci nahani trap / floor trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( one part of lime, two part of sand and five part of 40mm gauge brick jelly ) and finished with cement mortar 1:3 ( one cement, three sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the ci / pvc pipes, etc., complete complying with standard specification. ( the nahani trap should be got approved by the executive engineer before use on works ) 64 supply and fixing in position of best indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with gi pipe, 32mm dia bell mouth pvc connection and waste pipe, 15mm dia gi pipe of required length, 15mm dia gm wheel valve, 15mm dia brass nipple 2 nos., and fixing the urinals in position with necessary tw plugs, clamps, screws, etc., including dismantling masnory and re doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. ( the urinal should be got approved by the executive engineer before use on works. ) 65 bore well 66 drilling bore well anywhere in chennai city including transportation from one place to another place within alluvial soil or sedimentary rock clay and sand or stone pebbles, boulders etc., by first taking a pilot bore of 140mm / 150mm / 200mm and the enlarging to required depth direct or reverse rig fuel, drilling the betonite mud and water required for drilling by departmental officers including construction of mud pts. ( water available with a lead of 1.50km ) 67 300mm 68 150mm 69 reaming from 200mm pilot bore to 300mm dia bore upto 60m depth ending below ground level and as directed by the departmental officers. 70 supply and laying following dia pvc casing pipe with excise duty as per is 12818 / 1992 71 200mm dia cs ( plain pipe ) 72 200mm dia rs 73 150mm dia rs 74 labour charges for inserting pvc casing pipes assembly ( with slots or without slots ) in the drilled hole including jointing the pipes with pvc couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the executive engineer of departmental officers. 75 200mm dia cs ( plain pipe ) 76 200mm dia rs 77 150mm dia rs 78 supplying and filling with river pebbles in annular space between bore and pvc pipe up to hard rock. 79 charges for developing the borewell with air compressor of 300 cfm capacity ( minimum 8 hours ) including transportation labour and fuel charges for compressor as directed by twad board officers and conducting yield test by v notch method. 80 supplyand erection of 2.hp submersible pump set using nylon rope including cost of motor , fixing necessary cable charges and labour charges etc., complete ( for sump & bore well ) 81 supplying and fixing in position best quality of hdpe pipes with isi mark of following dia with specials including cost and coveyance of hdpe pipes and specials, labour charges for erection of pipes in the borewell and jointing materials etc., all complete as directed by the departmental officers. 82 dismantling removing reinforced cement concrete work and etc., by mechanical means including stacking of steel bars and disposal of unserviceable material within 50m lead as per direction of engineer in charge 83 conveyance of earth / debris to a lead of within 30 km from site as directed by the engineer inculding loading, unloading, hire charges for vehicle and other incidental charges etc., all complete as directed bythe departmental officers. 84 supplying and erecting in position of following liters capacity industrial model reverse osmosis water cum purifier to deliver potable water with world health organisation ( who ) standards with following accessories. ( a ) ms skid 1 no. ( b ) media 11054 no. vessel with 20 nb multiport valve ( with media pubble and fine sand and activated carbon filling ) set ( c ) feed pump 0.50 hp – 1 no. ( d ) vertical pump 2 9, 2.00 hp / single phase – 1 no. ( e ) membrane 40 x 40 filmtech ( or ) equilaents / osmonic ( usa ) 1 no. and membrane pressure vessel 40 x 40 1 no. & pressure gauge 2 nos. ( f ) flow meter 1 no. 20” filter with housing 1 no., low pressure switch 1 no., level switch 1 no. & necessary cpvc pipes and fittings. the system shall be provide with two panel control system with necessary stainless valves and fittings and float control etc. the rate should be inclusive of all civil works, wherever necessary to install the system in position and intact. 50 litres 85 supply and fixing of water co2 stored pressure type 9 litres capacity fire extinguisher as per new is 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the departmental officers. 86 supplying and planting of black eyed susanvariety of height 6 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 87 supplying and planting of thornless velvet rose variety of height 1 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 88 supplying and planting oflilium longiflorum variety of height 1 in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 89 supplying and planting of quisqualis indica variety of height 13in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 90 supplying and planting of bougainvillea variety of height 16in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 91 supplying and planting of hydrangea macrophylla variety of height 9in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 92 supplying and planting of vinca minor variety of height 3in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 93 supplying and planting of acalypha variety of height 1in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 94 supplying and planting of canna indica varigatedvariety of height 14in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 95 supplying and planting of coleus plant ornamentalvariety of height 1in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 96 supplying and planting of cypress tree variety of height 6 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 97 supplying and planting of dypsis lutescenstree variety of height 8 10 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 98 supplying and planting of plumeira albatree variety of height 8 10 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 99 supplying and planting of polyalthia longifolia tree variety of height 8 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 100 supplying and planting of neem treevariety of height 8 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 101 supplying and planting of coccoloba uniferatreevariety of height 810 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 102 supplying and planting of mimusops elengitreevariety of height 810 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 103 supplying and planting of moringa oleifratreevariety of height 3 in polythene bag of dia 30cm including supporting stack of 5 cm diacasurina pole of 5 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of requiredsize, planting of sapling, refilling of excavated earth etc as directed by the site in charge 104 supplying and planting of tabernaemontana divaricatavariety of height 16in polythene bag of dia 30cm including , including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge 105 irrigation work 106 supply, fixing & commissioning of pop up spray head robust design 1804 seal a matic ( sam ) pressure regulating series spray bodies, with rotary nozzle with capable of covering 4.0 7.3m at 1.4 3.8 bars pressure, rotary nozzles shall have hand adjustable ( without tools ) radius and arc 45 to 270 degree or full circle true flushing mechanism, thick streams andlarge water droplet & low precipitation rate. triple blade wiper seal precisely balances flushing, flow by and debris rotection to optimize performance and durability at pop up and retraction. precision controlled flushing at pop up and retraction clears debris, ensuring positive stem retraction in all soil types. unique debris pockets hold grit in place, removing it from circulation and preventing long term damage. parts resistant to corrosion in treated recycled water containing chlorine. pop spray body shall with stand upto 6.9 bar. built in seal a matic™ ( sam ) check valve. traps water in lateral pipes in elevation changes of up to 14 feet ( 4.2 have a double lacquering made out of highly concentrated fluomax pvdf on both side, double pvc coating and be weldable without grinding to make sure the fabric have less environmental impact the fabricator has to deliver evidence of r park 107 supply, fixing & commissioning of 5004 plus sam prs series rotor pop up sprinkler full / part circle having radius of 6.7m 12m @ 2.5 4.5 bar with discharge of 0.09 0.61 ltr. / sec. the sprinklers having arc adjust thru top cover w / std. screwdriver the sprinkler is gear driven rotary type with having 3 / 4 bottom inlet. oversized wiper seal, rain curtain technology, gentle closein watering and self flushing arc adjustment port and also having tapered riser stem with wiper seal the sprinkler shall have plus ( pressure loss ) flow shut off, 45 psi pressure regulator with flow optimizer technology, internal seal a matic device which prevents low head drainage ( upto 3.1m ) & hence puddling & erosion. the body of sprinkler is of non corrodible, heavy duty, anti breaking system plastic. o ring slip clutch, racheting slip clutch, side inlet available 6 and 12, turret mounted internal dia plugs, flow stop available, non potable water indication available etc., complete including installation charges. ( rain bird, toro, k rain or equivalent brand ) park 108 supply of 3 / 4 pop up connecting swing joint assembly. the tubing shall beof polyetylene having wall thickness of 2.3mm, a working pressure of 5.5 kg / cm2 at 430 c and a surge pressure of 16.6 kg / cm2. the fittings shall be made of uv resistant thermo plastic.sa series including installation charges. pd 1585 109 supply of 3.0 twin disc filter 50 m³ / hr. including installation charges. ( brands like rain bird or equivalent ) pd 1587 110 flexible polyethelene irrigation pipe 16 mm dia / 2.5 / 1.1 1.4 mm cl ii. including installation charges. netafim or equivalent brands. pd 1589 111 supply of pressure compensated dripper with 2 / 4 / 8 lph outlet flow including installation charges. rain bird / netafim makeor equivalent make. pd 1591 112 supply of endcap, nipple, start nipple, rubber grommet 16 mm dia. including installation charges. netafim or equivalent brands. pd 1590 113 supply, installation, testing and commissioning of sperinkler system with 2 hp, 230v motor with 380 lpm, 2.80 kg / cm2 pressure, with a head range of 22 30 meter, suitable to support sprinkler and dripper, including installation all inclusive. 114 supply, fixing & commissioning of a double acting airand vaccum release 2 air release valve . the air release valve shall be capable of both releasing and admitting air from and into the line. the working pressure shall be 10 ksc etc., complete, the rate including cost of all materials, labour charges, transportaion charges etc., complete complying with standard specifications as per the direction of departmental engineer in charge. 115 children play equipment 116 design, manufacture, supply, erection and testing and commissioning of puppy dog rider with a size of 0.9 m x 0.40 m x 0.76 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. the rider is of size 0.9 m x 0.4 m x 0.55 m, bolts, nuts, screws, washers and etc., used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety feature. all joints are robotic welded including all civil works as required complete 117 design, manufacture, supply, erection and testing and commissioning of elephant rider with a size of 0.9 m x 0.40 m x 0.76 mcomply with en 1176 safety standards. the en 1176 certificates issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. the rider is of size 0.9 m x 0.4 m x 0.55 m. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete 118 supply and fixing of arch sea saw sea saw made of g.i.sheets with 2 stainless steel pipes boards to play 4 c hildren simultaneously. seats made of fiber reinforced plastic. 119 design, manufacture, supply, erection and testing and commissioning ofpod swingwith a size of 2.83 m x 1.30 m x 2.50 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc.all products must be tested and certified to meet en 1176 safety standards. the en 1176 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. an inverted ‘u’ shaped structural posts of height 2.50 m are to be schedule hot dip galvanized steel with a 114mm od and 2.2mm ( wall ) thickness of the tubing. the poles are welded on to a base plate made from steel with 114mm inner diameter. at top a metal sheet is provided which shall be an all robotic welded unit, fabricated fromgalvanized steel pipes. swing seats are all robotic welded fabricated the electro statically applied polyester powder has a tough finish with maximum durability. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en1176 standards. all joints are robotic weldedincluding all civil works as required complete. 120 supply and fixing of see saw 4 seater withfiber reinforced plastic of width 7ft 0” and supporting frame made of 40mm stainless steel pipes and swinging arm made of 50mm stainless steel pipes of length 8ft 0”.handle made of 19mm stainless steel pipes seats are fiber reinforced plastic etc. including all civil works as required complete. 121 design, manufacture, supply, erection and testing and commissioning of multi play system ( kpsnk 005 ) with a size of735 x 735 mm comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. the new hdpe play panels include different games, each with their own unique hdpe panel design. all panels are available in other colours or languages on request. the mounting holes must be drilled on installation. 3 in a row form three discs of your colour in a row in this classic game for two .unique hdpe panel design. solid hdpe material thickness 19 mm. available in other colours / languages on request. mounting holes to be drilled depending on installation. all joints are robotic welded. all components designed and manufactured to meet with en1176 safety standards including all civil works as required complete. 122 supply and fixing of merry go round – 6 seater ( frp ) height :3” gi pipe, 2.5mm thick, b class seat size:15” x 14”, paint: pu coating. 123 design, manufacture, supply, erection and testing and commissioning of multy play system type 1 ( kpsnk 008 ) with a size of980 x 735 mm comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. the new hdpe play panels include different games, each with their own unique hdpe panel design. all panels are available in other colours or languages on request. the mounting holes must be drilled on installation. race your sliding disc as quick as possible from start to finish. unique hdpe panel design. solid hdpe material thickness 19 mm. available in other colours / languages on request. available in other colours / languages on request. all joints are robotic welded. all components designed and manufactured to meet with en1176 safety standards including all civil works as required complete. 124 supply and fixing of duck merry go round: [ measurement ] height:2ft width:7ft [ component ] leg :3” galvanished ‘b’ class pipe seat :frp duck 4nos. with isotolic gel coat with uv pigment.support : 1 ½” galvanished ‘b’ class pipe. painting with pu coating [ wanted area ] product area : ø 7’ft play area : ø 9’ft 125 design, manufacture, supply, erection and testing and commissioning of triangle rope climber with a size of 2.33 m x 1.5 m x 1.5 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. support posts of height 2.1 m are to be schedule galvanized steel with a 89 mm od { outer diameter } . specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be oftamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 126 design, manufacture, supply, erection and testing and commissioning of hexa climber with a size of 2.2 m x 2.1 m x 2.3 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. these en 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. upright structural posts of height 2.3 m, are to be schedule galvanized steel with a 114mm od { outer diameter } . parallel climber of size 1.9 m x 1.17 m , horizontal ladder 1.9 m x 1.17 m , pull up bar, chain climber of size 1.9 m x 1.17 m, and gymnastic rings of size 0.77 m x 1.17 m shall be an all patent welded fabricated from 54 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 127 design, manufacture, supply, erection and testing and commissioning ofcrawl tunnel with a size of 1.94 m x 1.54 m x 1.3mcomply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. upright structural posts of height 1.3 m are to be schedule galvanized steel with a 114mm od { outer diameter } . the tunnel of size 1.94 m and dia 900 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 128 design, manufacture, supply, erection and testing and commissioning oftoddler multi play system type 2 with a size of4.10 m x 2.30 m x 2.60 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. with upright structural posts of height 2.0 m, are to be schedule galvanized steel with a 114mm od { outer diameter } . deck of size 0.80 m x 0.80 m and staircase of size 0.91 m x 0.39 m shall be an all robotic welded assembly fabricated from perforated solid punched steel. deck perimeter is precision pre punched for attachments. decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. handrail of height 1.5 m and dia 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. frisby climber, piped walls of size 1.52 m shall be an all robotic welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. galvanized steel for the inner parallel bars. roof of size 1.17 m x 1.17 m x 0.85 m straight slide of size 1.46 m x 0.45 m x 0.95 m. a shaped swing of size 1.73 m x 1.24 m shall be fabricated from 32mm o.d. galvanized steel pipe. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded including all civil works as required complete. 129 design, manufacture, supply, erection and testing and commissioning of customized adventure system hps 2 with a size of10 m x 8.56 m x 4.2 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc.curved structural poles of height 2.6 are to be schedule galvanized steel with a 114mm od { outer diameter } . handrails of dia 60 shall be an all patent welded unit, fabricated from 32 o.d. galvanized steel pipes. wiggle triangle crawl of size 1.08 m x 0.13 m ( single triangle ) , stepping stones of dia 0.32 m ( single stone ) , elliptical shaped climber of size 2.12 m x 0.64 m, plastic components, net climbers shall be an all patent welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. galvanized steel for the inner parallel bars. slide of size 2.77 m x 0.46 m x 1.21 m. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotics welded including all civil works as required complete. 130 design, manufacture, supply, erection and testing and commissioning of multiplay system type 3 with a size of 10.04 m x 6.19 m x 4.2 m comply with en 1176 safety standards. the en 1176 certificates issued by an international certifying body such as ipema, tuv, cpsc, or sgs etc. upright structural posts of height 2.3 m, 2.9 m and 3.3 m are to be schedule galvanized steel with a 114mm od. deck of size 1.16 m x 1.16 m and staircase of size 1.4 m x 1.35 m shall be an all robotic welded assembly fabricated from perforated solid punched steel. deck perimeter is precision pre punched for attachments. decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. handrail of height 1.88 m and dia 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. step climber size is 1.0 m x 0.5 m x 2.7 m, piped walls of size 2.4 m, shall be an all robotic welded fabricated from 32 o.d. galvanized steel pipes for the outer pipes and 25mm o.d. monkey bar size is 2.35 m x 1.0 m x 2.13 m shall be an all robotic welded fabricated from 32 o.d. galvanized steel for the inner parallel bars. roof of size 1.5 m x 1.5 m x 0.93 m, 131 straight slide of size 1.68 m x 0.66 m x 1.8 m, wavy slide of size 3.17 m x 0.58 m x 2.4 m, spiral slide of size 1.31 m x 1.73 m x 2.7m, plastic climbers of size 1.06 m x 0.73 m x 0.96 m, tunnel, panels, plastic components. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as a safety. all joints are robotic welded. all components designed and manufactured to meet with en 1176 safety standards including all civil works as required complete. 132 gym equipment 133 supply, erection and fixing of arm & shoulder wheels 1300 x 1200 x1350 mm 4mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. 134 design, manufacture, supply, erection and testing and commissioning of tai chi spinners with a size of 1.25 m x 1.09 m x 1.49 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only.the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.49 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. circular handrail of dia 477 mm made with the pipe dia of 32 mm shall be an all robotic welded unit, fabricated from 32 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standards including all civil works as required complete. 135 supply and fixing of double cross walker cardio, lower / upper body exercise. main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes ( 1680 x 515 x 1780 mm ) 4 mm pipe double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. steel foot rest / foot paddle for long lasting life. 136 design, manufacture, supply, erection and testing and commissioning ofelliptical cross trainerwith a size of 1.02 m x 0.53 m x 1.52 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.25 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two numbers of foot rest of size 320 mm x 132 mm are attached to the standing bars 998 mm x 40 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. lower part of support handrails of size 0.8 m high and dia 47 mm and upper part of support handrails of size 0.51 m high and dia 32 mm are all robotic 137 welded fabricated from 47 mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 138 supply and fixing of push pull up chair promotes upper body and triceps strength lat pull down develops upper body strengths size 2900 x 775 x 2060mm main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes double coat powder coating, heavy duty branded sealed ball bearing, for long lasting life. steel foot rest / foot paddle for long lasting life. . 139 supply and fixing of twister & leg trainer back and spinal joint exercise. strengthens abdominal and spinal. also increase flexibility of upper and lower and spinal. also increase flexibility of upper and lowerback. size 1700 x 510 x1425mm ) 4 mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes thick rexin covered cushioned seat. double coated powder coating, heavy duty sealed ball bearing, for long lasting life supply and fixing of twister & leg trainer back and spinal joint exercise. strengthens abdominal and spinal. also increase flexibility of upper and lower back. size 1700 x 510 x1425mm ) 4 mm pipe main post made of 4 inch pipe and other main pipes 1 1 / 2 inch pipes. 3 mm thickness pipes thick rexin covered cushioned seat. double coated powder coating, heavy duty sealed ball bearing, for long lasting life 140 resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. all joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 141 design, manufacture, supply, erection and testing and commissioning of self weight rower with a size of1.26 m x 0.80 m x 1.59 mcomply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. horizontal bars of length 1.08 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. handle bars of 0.74 m and dia 38 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 142 design, manufacture, supply, erection and testing and commissioning ofmini ski with a size of 1.07 m x 0.78 m x 1.40 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.40 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. the standing bars 991 mm and dia 60 mm. upper part of support handrails of size 1.04 m high and dia 38 mm are all robotic welded fabricated from 40mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant 143 stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 144 design, manufacture, supply, erection and testing and commissioning of bicycle of size 0.97m x 0.49 m x 1.30 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates. upright structural posts of height 1.33 m is to be schedule hot dip galvanized steel with a 60 mm o.d. and 2.2mm ( wall ) thickness of the tubing. two numbers of pedal of size 113mm x 40mm & rotating disc of dia 380 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be 145 covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 146 design, manufacture, supply, erection and testing and commissioning of squat pusher with a size of 1.93 m x 0.56 m x 1.70 mcomply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.vertical bars height of 1.50 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. l shaped bars of 960 mm x 600 mm carrying two seats of 0.34 m x 0.34 m shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured tomeet with en6630 safety standardsincluding all civil works as required complete. 147 design, manufacture, supply, erection and testing and commissioning of sit up station with a size of 1.48 m x 1.21 m x 0.63 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 0.63 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two j shaped bars of 1.07 m and dia 48 mm. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 148 supplying and fixing of leg extension / leg curf : pl 9019 of glass fiber reinforced nylon pulleys with deep v groove provides secure cable seating and fluid bearing rotation. shroud is applied to protect the equipment or the possible injury during operation. tubing: 2.5 mm to 2.75 mm square tube differ into any types, from 30 x 60x 2.75 mm square tube differ into any types, from 30 x 60mm to 50 x 100 mm, electro welded to maximum integrity. pad total thickness is 70 mm dimension: 1465 l x 1245 w x 1520 h ( mm ) product weight: 115.5 kg / 255 lbs warranty: 1 year. 149 design, manufacture, supply, erection and testing and commissioning ofdouble air skier comply with a size of1.61 m x 0.52 m x 1.51 m with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 1.25 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. the foot rest of size 365 mm x 164 mm is fixed to the standing bars of length 1640 mm x 40 mm shall be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. lower part of support handrails of size 0.8 m high and dia 47 mm and upper part of support handrails of size 0.51 m high and dia 32 150 mm are all robotic welded fabricated from 47 mm o.d. and 32 mm o.d. galvanized steel pipes. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 151 supplying and fixing of lat pull down / seated row: pl 9002 of glass fiber reinforced nylon pulleys with deep v groove provides secure cable seating and fluid bearing rotation. shroud is applied to protect the equipment or the possible injury during operation equipment or the possible injury during operation tubing: 2.5 mm to 2.75 mm square tube differ into any types, from 30 x 60 mm to 50 x 100 mm, electro welded to maximum integrity. pad total thickness is 70 mm dimension: 1764 l x 1019 w x 2182 h ( mm ) product weight: 90.5 kg / 200 lbs warranty: 1 year 152 exposed hardware shall be covered with safety caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 153 design, manufacture, supply, erection and testing and commissioning of seated chest press with a size pof 1.82 m x 0.69 m x 1.88 m comply with en16630 safety standards with gs test mark. the en16630 certificates must be issued by a reputed notified international certifying body such as ipema, tuv, cpsc, or sgs only. the gs mark en 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors.all products must clearly display the gs mark as has been issued in the en16630 safety certificates.upright structural posts of height 1.88 m is to be schedule hot dip galvanized steel with a 114mm o.d. and 2.2mm ( wall ) thickness of the tubing. two pair of u shaped bars of 1.02 m and dia 40 mm while the handles are placed at a spacing of 698 mm shall 154 be an all robotic welded unit, fabricated from 40 o.d. galvanized steel pipes. joints are robotic welded. bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. exposed hardware shall be covered with caps as per en16630 standards. joints are robotic welded. all components designed and manufactured to meet with en 16630 safety standardsincluding all civil works as required complete. 155 play equipment 156 supply and fixing of badminton court poles 2 nos. ss 304with 46 x 46 mm 3mm poles with a overall height of 2.0 m height white colour powder coated with 80 micron thick, 1550 mm above ground and 450 mm below ground, nylon net with 1.0 m heightincluding excavation, civil work including cost of all materials , labour, lead lift etc., complete. 157 supply and delivery of aluminium alloy ovel frame with steel handle badminton racquetswith overall dimension of 680 mm long, 230mm frame width, 280 mm long string area, 95 mm grip perimeter string with high quality nylon confirming to the badminton federation of india standards.. 158 supply, installation of basket ball pole of 10 feet height 65 mm dia, with back stop unit, approved colour of powder coated with 80 micron thick, 25 mm acrylic sheetincluding excavation, civil work including cost of all materials , labour, lead lift etc., complete. 159 supply and delivery of rubberbasket ball for competition ( competition in all categories size 7. with inner nylon cloth lining, the outer surface of the ball shall be made of toxic free leather or rubber material with ball circumference range from 749 mm to 780 mm and mass of 567 g to 650 g ) 160 supply and delivery of rubberfootball made out od moulded synthetic material with 32 panels, hand stitched, with a size of 580 600mm dia, weigh of 3002 to 320 grams all inclusive. 161 supply and delivery of rubbervolleyball spherical shaped, made out of moulded synthetic material, hand stitched, with a circumference, latex bladder, of 660 mm size weigh of 270 grams cotton stitching, all inclusive. 162 electrical 163 tneb metering boardsupply and fixingof tneb meter board suitable for 3 phases 100 a service connection made up of suitable iron angel frame work of size 2 feet x 1.5 feet using angle iron of size 1 1 / 2 x 1 1 / 2 x 1 / 4 rigidly fixed on wall covered with hylem sheet of size 2 feet x 1.5 feet of 12 mm thickness with necessary bolts and nutt supports and supply, installation and commissioningof 3 nos 100 a fuse units ( 500v ) , 1 no neutral link , copper flat of size 1 x 1 / 4 with interconnection of eb meter to fuse units by 19 / 16 pvc insulated copper wire with earth connection and to complete the work etc. 164 250a isolator switch supply and fixing of 200a tpn switch disconnector fuse units in sheet steel enclosure with hrc fuses double break on suitable angle iron frame work with ms cable entry boxes with pwd earthing. 165 supply and fixing of 6 way vertical triple pole and neutral mccb sheet steel enclosure distribution board ( with mccb incomer ) with double door ( metal door ) with 1 no. 160 a 4 p mccb switch as incoming and 4nos. 63a 3p mcb , 6 nos. 6a to 32a sp mcb as outgoing with suitable cable end box on wall with earth connection only. 166 supply and fixingof8 way verticaltpmcbsheetsteel industrial type tpmcb db with ip54 protection of surface type fitted with bus bars and neutral links with1 no. of 63a fp mcb as incoming and 4 nos. of32a, 10ka triple pole mcb in flush with wall and making good of the concealed portion with earth connection. ( industrial type tpmcb db with ip54 protections ) 167 supply and fixing of 7 segment8 way63a tpn mcb sheet steel distribution board ( higher end ) with metal / acrylic doorcover flush type / surface type fitted with busbars and neutral links with single / three phase mcb outgoings and separate 4 way provision for accommodating one no. 4 pole incoming mcb / isolator and another separate 4 way provision for accommodating one no. 4 pole elcb / rcd ( totally 8 ways in one segment ) ( 3x 6 ways in each segment ) and separate provision for mcb / isolators ( totally 18 nos. ) for sub incomers in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. withthe following in flush with wall with earth connection only. 168 supply and fixing of 12way single pole and neutral mcb sheet steel enclosure distribution board with double door ( metal ) 1no. 32a 30 ma 4 pole elcbas incoming and10 nos. 6a to 32a sp mcb outgoing in flush with wall. the mcb db and mcbs should be with isi mark ( like standard make ) 169 supply and laying of following xlpe armoured ltug cable in a trench / tray with suitable cable tie tag etc as required. 170 supply and laying of 3 1 / 2 x 70 sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 171 supply and laying of 31 / 2 x 35sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 172 supply and laying of 31 / 2 x 25sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 173 supply and laying of 4c x 16 sq.mm. pvc armoured ltug cable in suitable size hdpe pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 174 supply and clamping of following xlpe armoured ltug cable on post or on wall ms clamps , saddles, plugs, screws etc., as required. 175 supply and clamping of 3 1 / 2 core x 70 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 176 supply and clamping of 3 1 / 2 core x 35 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 177 supply and clamping of 3 1 / 2 core x 25 sq.mm pvc armoured ltugaluminium cable on post or on wall ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 178 supply and clamping of 4c x 16 sq.mm pvc armoured ltugaluminium cable on post or on wall with ms clamps, saddles, plugs, screws etc., complete including transport charges of ug cable. 179 supply and fixing of double compression brass cable gland for following aluminium conductorxlpe insulatedarmoured cable of 1100 v grade with earth connection. 180 supply and fixing of brass cable gland for3 1 / 2 cx 70 sq.mm pvc ltugarmoured cable with earth connection 181 supply and fixing of brass cable gland for3 1 / 2 cx 35 sq.mm pvc ltugarmoured cable with earth connection 182 supply and fixing of brass cable gland for3 1 / 2 cx 25 sq.mm pvc ltugarmoured cable with earth connection 183 supply and fixing of brass cable gland suitable for4c x 16 pvc armoured ltug cable with earth connection. 184 supply and providing cable end termination of the following sizepvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete ( copper sockets for copper cables and alu. sockets for alum. cable ) 185 supply and providing cable end termination of 3 1 / 2corex 70 sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 186 supply and providing cable end termination of 3 1 / 2corex 35sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 187 supply and providing cable end termination of3 1 / 2corex 25sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. 188 supply and providing cable end termination of 4 c x 16sq.mm pvc ltug aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete. 189 wiring with 2 x1.5 sq.mm. ( 22 / 0.3 ) pvc insulated single core unsheathed copper conductor of 1100 v grade in suitable pvc rigid pipe concealed in wall and ceiling with pvc accessories with module gi switch box in flush with wall with 6a one way module switch with module front plate continuous earth wire connection by 1.0 sq.mm. pvc insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour for concealed pvc light point / fan point ( for electronic regulator ) ( 4points / coil ) higher end 190 wiring with 2 x 1.5 sq.mm. ( 22 / 0.3 ) pvc insulated sc unsheathed copper conductor of 1100v grade in suitable pvc rigid pipe concealed in wall and ceiling withmodule gi switch box in flush with wall with 6a one way module switch with module front plate continuous earth wire connection by 1 sq.mm. pvc insulated sc unsheathed copper wire and making good of the concealed portion with suitable colour for pvc concealed light ( 6 points per coil ) ( for rooms like bath, toilet & pumproom, etc. ) . 191 wiring with2rx1.5sqmm ( 22 / 0.3 ) pvc insulated unsheathed sc cu. conductor of 1100vpvcconduit pipeconcealed wall and ceilingwith pvcaccessoriesgi metal back box and 6a modularswitch & 6a modular socket ( board itself point ) in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, for making good of the concealed portion with suitable colour for pvc concealed point ( 8 points / coil ) 192 supply, run, testing and commissioning of2 run x 2.5 sqmm and 1r of 1.5sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 193 supply and run of 50mm dia.hdpe pipe of 4kgf / cm2 approved quality and best variety conforming to iss and isi markbelow ground inhdpe pipes 194 supply and installationof 16m high mast shaft in two sections suitable for 50 m / sec wind speed, with head frame, winch mounting bracket, luminaries carriage suitable to install 8 nos of 150w led light fittings luminaries ( semi circle arrangement ) with counter weight arrangements , mounting clamp and brackets etc. raising , lowering system comprising double drum winch, suitable ss wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lighting finial, lightning spike if require, wiring material from jb to individual luminaire & mcb in base compartment are included and are a part of installation, foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. 150w led single light fitting dome aviation obstruction light, outdoor stand mounted feeder pillar with 63a 4pole rccb with 100ma, single dial time switch, 45a tp contactor for the automatic switching of luminaries , power tool control with 2 no 9a contactors and raise lower push button, incoming 35 sq. mm and outgoing 25& 4.0 sq. mm terminals, shallow foundation with m25 grade concrete for the high mast considering the safe soil bearing capacity at site as 10 t / sqmtr at 2 metre depth with all materials and labour, gi pipe earthing for high mast with 2.5 m long 40mm die gi pipe including connection to high mast earth terminal with 25 x 3 mm gi flats with all materials and labour ( 2nos per mast required ) , wiring of luminaires with all wiring materials like pvc insulated pvc sheathed flexible cable of suitable copper conductor cores of 2.5 sq. mm, lugs, mcb and all labour, mast feeder pillar by grouting the stand in concrete. with allnecessary components for the complete functional operation. contractor to getstructural approval from the civil team for the high mast foundation 195 supply and fixing of 150 mm dia. gi pipe ( class b ) of 9 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 10a sp mcb , 2 / 4way connector on suitable hyleg sheet and with supply and fixing of unique modular 250w led floodlight made up of pressure die cast aluminium housing with toughened glass and high power leds and secondary lenses with ip66 protection. available in nb / mb / wb angles. 10kv spd included, system efficacy = 110 / 120 / 135 suitable to operate in 120 280 v ac, 50 / 60 hz complete with suitable ms brackets for 200w led floodlight fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour. crompton cfs 501 300 57 60d hl3 gl nbkg 196 supply and fixing of 65 mm dia. ( 2 1 / 2 ) gi pipe ( class b ) of 6 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 10a sp mcb , 2 / 4way connector on suitable hylem sheet and with supply and fixing of floodlight luminaire with superior polycarbonate optics pressure die cast housing, ip66 ingress protection, 4kv in built and 10kv external surge protection. efficacy 110lm / w. available in nb / mb / wb angles. complete with suitable ms brackets for 200w led floodlight fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour. ( sd 543 ) . ( bajaj gleam f 220l wh sy pc sd v2 ) 197 supply and fixing of 65 mm dia. ( 2 1 / 2 ) gi pipe ( class b ) of 4 metre length with 300mm x 300mm x 6mm ms base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable smc box with door arrangement to house 6a sp mcb switch, 2 / 4 way connector on suitable hylem sheet and supply and fixing of 45w led toplight fitting with led ( higher end ) with 1 metre 32mm dia. gi pipe ( class b ) complete with suitable ms clamps for led street light fitting and smc box with pvcunsheathed copper leads from smc box to fitting and with painting of suitable colour ( sd 541 ) ( 45w led top light fittings 198 supply, installation, testing & commissioning of 10w led bollard light fittings fitting. the light fitting should be powder coated with high pressure die cast aluminium led housing. and the led fixed on die cast aluminium heat sink for proper thermal management.and the operating voltage range 140 – 270v ac, provided with open and short circuit protection and input surge voltage protection. the driver should be constant voltage constant current smps protection of fitting should be ip 66. led having 50, 000 burning hours with minimum 70% lumen maintenance and power factor 0.95.system consumption should be require with lumen package as per requirement. crompton cat ref : lbla3 10 cdl / equivalent ( landscape light ) . rate shall inclusive of necessary joint kit, glands, etc., for loop in / outconnection suitable to outdoor application . 199 supply and fixing of 30w led street light fitting with led ( higher end ) with 25 mm dia. gi pipe ( class b ) with 1 no. 25 mm gi bend complete on the existing post / on wall with pvc unsheathed copper leads with ms clamps and withpainting. 200 supply, installation, testing and commissioning of 18 w led down light fittingwith ip55 cool day light suitable for pole mounting, made outcrca powder coated body, aluminium reflectors, poly methyl meth acrylate ( pmma ) diffuser, glare free light, including electronic drivers, day light colour led lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive. 201 supply, installation, testing and commissioning of 40 w led tube light fitting with cool day light made out of crca powder coated body, poly methyl meth acrylate ( pmma ) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour led lamps, inter connecting wiring including accessories all inclusive. 202 supply and fixing ofpressure die cast aluminium housingbulk head 10w led fitting with ip65 protected withpvc unsheathed copper leads from terminals to the fitting. model equivalent to cromptonlbhe 10 cdl ( rate as per quotation ) ( philips / bajaj / crompton / k.lite ) 203 supply and fixing of 1200mm ( 48 ) sweep ac ceiling fan 5 star rated complete ( higher end ) with 2 module 100w fan step regulator ( higher end ) with 600mmdown rod with fan clamp, and wiring to the nearby by point with 1.5 sqmm frls , pvc insulated copper wires, including necessaryaccessories and hardwares as required. 204 supply and fixing of 300mm ( 12 ) sweep ( heavy duty ) ac exhaust fan complete with necessary wall opening and making good of the wall and wiring to the nearby by point with 1.5 sqmm frls pvc insulated copper wires including necessaryaccessories and hardwares as required. 205 supply and fixing of louvers shutters arrangements for 300mm ( 12 ) sweep ( light duty ) ac exhaust fan, including necessaryaccessories and hardwares as required. 206 supply and fixing of 1 no.16a two modulesocket , 1 no.16a one module switch with module cover plate ( plastic ) onsuitable module concealedbox ( gi ) in flush with wallwith connections. scope cover wall cutting , grouting , flushing and making good on the wall. higher end. 207 supply and fixing of 2nos.6a two module 5 pin socket , 2 nos. 6a one module switch with module cover plate ( plastic ) on suitable module concealed box ( gi ) in flush with wall with connections. scope cover wall cutting , grouting , flushing and making good on the wall. higher end. 208 earthing as per the isi specification with an earth electrode of 2.10 metre class b gi pipe of dia. not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp andwithcopper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm rcc cover slab for the brick masonry 209 coil earth to street light poles with no.8 swg gi wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length ( 75mm to 100mm dia. ) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth. 210 supply, fabrication, of gi / copper earth flatof following size in provided trench, clamping in wall, ceiling, with suitable clamps / saddles, connecting the joints through bracing / welding covering withtermination in the earth pits, panels, distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive 211 25 mm x 6mm gi flat ( sd 77 ) 212 no8 swg copper ( m 1571 ) 213 no8 swg gi 214 lighting rodsupply of early streamer emission air terminal ( eseat ) .model: sthe eseat has corrosion resistant stainless chrome body made up of aisi 316 grade of height 0.50 metres capable of working in hazardous atmosphere. the air terminal is non radioactive and requires no special licensing. the unit is fully autonomous ( no battery, no external power supply is required ) , collects energy from the ambient electric field. the eseat model has been tested in a high voltage laboratory in accordance with nfc 17 102 in order to measure the average gain in triggering. the average gain in triggering time ( ?ts ) obtained during the lab test for the offered model is 60 μs. the eseat works on negative as well as positively polarized discharges. eseat has been tested for such discharges in central power research institute ( cpri ) . a dedicated tester is available to test the healthiness of the eseat on request ( page no. 37, point no. 3 of clause 8.6 of the revised nfc 17 102 version 2011 ) . eseat model : s radius of protection : 46 metres level of protection considered for the project ii level 215 mounting structuresupply of standard / special mounting structure of height 4.5 mts. pipe, and 300 x 300 x 8mm ms plate, 3 mts. 48mm odclass c gi outer pipe, 1.8 mtr, 38mm od inner pipe, for roofmounting on concrete base and with frp adapter 216 down conductorsupply and run of 25mm x 6mm gi flat down conductor with necessary clamps / supports on wall / floor / ground for earthconnection 217 test linksupply of test link box for each down conductor in order to disconnect the earth termination system to enable measurement of resistance 218 supply and installation maintenance free gi earthing system comprising of 50mm dia. and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp 219 surge protectionsupply and installation cabinet type class 1 and 2 combined model spd to arrest surges and over voltage in the power line due to lightning switching action etc. they must be installed in the incoming mcc panel / db of the respective building in parallel to the power circuit. model: psv4 12.5 / 400tt ( 3 phase power network ) 220 first aid box complete with all first aid medicines ( m 1977 ) 221 shock treatment chart fixed in glass frame ( m 1978 ) 222 danger board as required by the electrical authorities ( m 1981 ) 223 supply and kept in position of 9 litres capacity fire buckets of 4 nos. with bucket stand as per standard specifications and as directed by the departmental officers 224 supply and fixing of carbon di oxide gas type 2 kg. capacity fire extinguisher as per new is15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the departmental officers. make: excellent / safety first / equivalen 225 cctv system 226 supply, installation, testing and commissioning of 32 channel 8 sata nvr, with 6t hard disk drive 4 nos, new logical and visualized gui design dual os design to ensure high reliability of system running, anr technology to enhance the storage reliability when the network is disconnected, configurable normal or hot spare working mode to constitute an n+1 hot spare system video input and transmission, connectable to the third party network cameras compression and recording, h.265+ compression effectively reduces the storage space by up to 75%, full channel recording at up to 12mp resolution hd video output ? hdmi1 / vga1 outputs provided ? hdmi1 video output at up to 4k ( 3840 × 2160 ) resolution storage and playback, upton 16 sata interfaces and 1 esata interface for hdd connection, support up to 10tb capacity for each hdd, smart search for efficient playback. and smart playback to improve the playback efficiency, supports vca search for fire / ship / temperature / temperature difference detection triggered video files, pos information overlay on live view and playback, pos triggered recording and alarm network & ethernet access ? hik connect for easy network management, 2 gigabit ethernet network interfaces. ( make : hikvision / dahua / sony. 227 supply of 8mp, internet protocol fixed bullet camera with following specification:?1 / 2.5 progressive scan cmos, ? 3840 × 2160 @15 fps, 2.8 / 4 mm fixed lens, 01 lux @ ( f1.2, agc on ) , 0.028 lux @ ( f2.0, agc on ) , 0 lux with ir, h.265+, h.265, h.264+, h.264, 2 behaviour analyses ( line crossing detection, intrusion detection ) ? face detection ? 120db wdr, ? blc / 3d dnr / roi, ip67 complied?on board storage built in micro sd / sdhc / sdxc card slot, up to 128 gb, ? shutter speed 1 / 3 s to 1 / 100, 000 s, ? 3 axis adjustment pan: 0° to 360°, tilt: 0° to 100°, ? rotate: 0° to 360°, 2.8 mm, ? horizontal fov: 102°, vertical fov: 53°, diagonal fov: 124°, ?lens mount m12 ? ir range i5: up to 50 m, ? image settings rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ? power consumption and current 12 vdc, 0.7 a, max. 7.5w poe: ( 802.3af, 36v to 57v ) , 0.3 a to 0.2 a, max. 9w 228 ? camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. ( make: dahua / panasonic ) ( rate as per quotation enclosed ) 229 supply, installation, testing and commissioning of 55 smart led tv with following specifications a ) full hd 1920 x1080 ( 4k monitor ) b ) ips panel c ) slim back light led module d ) 900 pmi e ) triple xd engine f ) dynamic scanning g ) anrh ) true colour generatori ) 8modes of picture j ) picture wizardiii k ) real cinema 24p l ) hdmi 3nos m ) usb 3nos n ) built in lan o ) magic remotep ) dimension 1242 x 724 x 55.1min ( 37 ) . ( make: sony / lg / samsung ) . 230 supply and fixing of outdoor4x6pvc box with 102mm x 77mm x 102mm with all fixing accessories. 231 supply and clamping of cat 6 armoured cable in suitable pvcpipe 1 thick on wall / ceiling with connected pvc accessories with clamps, saddles etc., complete. ( between ethernet switch to camera and radio modem ) i. application : primary ( campus ) , secondary ( riser ) , tertiary ( horizontal ) ieee 802.3 : 10base t; 100base t; 1000base tieee 802.5 16 mb; isdn; tpddi; atmii. standards: iso / iec 11801 2nd ed.; iec 61156 5 2nd en 50173 1; en 50288 6 1, eia / tia 568c.2, rohs compliant.fire rating: pvc : iec 60332 1.iii. conductor bare copper wireiv. insulation polyethylene v. twisting 2 cores to the pair vi. cable lay up 4 core to the pair it has diameter of ( 23 awg ) 0.550 ± 0.015.insulation : polyethylene.gi wire of size is 0.90 ± 0.030mm. 232 fixing and termination of cat 6 cable rj 45jack single point ( point to point ) crimping, testing and arrangement charges. 233 supply, run, testing and commissioning of2 run x 2.5 sqmm and 1r of 1.5sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 234 supply and fixing of poe 24 port switch10 / 100 / 1000 base t / 2 x 1000base fx / 20gbps bandwidth / ieee803.af / at compliant poe+ / rj45 supports auto mdi / mdi x function / auto negotiation speed, half / full duplex / store and forward / max packet size: 10kbytes / wide range power design ( 12~56vdc ) / operating temperature ( 40 °c ~ +75 °c ) / reverse polarity protection / resettable fuse to protect against overcurrent / ip 40 protection / eft protection for power line. 235 supply and fixing of poe 8 port switch10 / 100 / 1000 base t / 2 x 1000base fx / 20gbps bandwidth / ieee803.af / at compliant poe+ / rj45 supports auto mdi / mdi x function / auto negotiation speed, half / full duplex / store and forward / max packet size: 10kbytes / wide range power design ( 12~56vdc ) / operating temperature ( 40 °c ~ +75 °c ) / reverse polarity protection / resettable fuse to protect against overcurrent / ip 40 protection / eft protection for power line. ( make: dlink, netgear / tplink ) 236 supply and fixing of out door weather proof box 2ft x 2ft out door weather proof box 2ft x 2ft 237 supply and fixing of rack with accessories higher end 42 u rack with lns unit and fan extra for the above rack. 238 supply and fixing of 2 feet cctv camera stand with attachment fittings as follows:* weather heads and couplings * cabinet mounting fittings, plates, brackets as needed. * reinforced couplings for wire entrances to cabinets. 239 supply and installation for 2kva ups with battery, single phase ups ( single phase in & single phase out ) capacity system with battery 2hours back up 240 supply and installation for 1kva ups with battery, single phase ups ( single phase in & single phase out ) capacity system with battery 1 hours back up 241 of 6mlengthpole with base plate of size 250x250x6mm as per is 875 with following specification. pole outer die 76.10mm x 3.65mm thick x 6 meter. 242 supply and filling in foundation and basement with m sand / filling sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification. 243 providing and relaying plain cement concrete 1:2:4 ( one cement two sand and ten broken machine crushed stone jelly ) using hbg machine crushed stone jelly of size 20mm gauge for founding and basement including de watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. 244 pa system 245 supply, installation, testing & commissioning of 30 watts 2 way high efficiency, high fidelity, long throw ip65 weather proof p.a music horn speaker. it combines the high efficiency of horn with wide frequency response. music horn is weather protected and uv protected abs plastic housing combines with the feature of easy poertap selection on a terminal strip with a two core cable. it has impedance of 250 / 500 / 1k / 2k ohm with frequency response of 120 16000 hertz. ( make: ahujaamh402t / bosch or its equivalent ) 246 supply, installation, testing & commissioning of 240 watts p.a mixer amplifier with the output power of 1350 watts maximum, 500watt rms at 10% thyristor harmonic distortion ( thd ) , 850watt rms at 5% thd, 800 wattsrms at 2% thd and the power supply ac voltage ranging from 220 240 volt, 50 / 60 hertz. with the dc input of 48 volt and 1000watts has tone controls of bass=+ 10 db at 100 hz weighing 42kg with the speaker output of2q, 4q.70volt&100volt has power consumption of 1600va ac &12a dc and 100db output regulation at 1khz no load to full load ratio. the signal to noise ratio is 60db with the input channels of 0.8mv / 4.7kq, 3*aux 100mv / 50kq.the frequency response of 50 15000hz+ 3db. ( make: ahuja ssa 10000 / bosch or its equivalent ) 247 supply, installation, testing & commissioning of10 gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedance and has 2.5mv / pa sensitivity and frequency response ranging from 50 15000hz with multi tone chime model. ( make: acm66 ahuja / bosch / its equivalent ) 248 supplyand run ofarmoured speaker cable 2 core 2.5 sqmm and 1r of 1sq sqmm pvc insulated sc unsheathedof 1100v grade in suitable pac conduit pipe onconcealed wall and ceiling with continuous earth wire connection with painting of suitable colour. 249 supply & installation of custom built m.s powder coated wall mounting audio rack with lock & key for housing of amplifier & player / recorder conforms to eia 310, iec 60297 and able to withstand the load of 40kg with welded construction made up of crca steel with suitable height, width and depth. 250 supply, installation, testing & commissioning ofcordless mic uhf model. ( make: acm66 ahuja / bosch / its equivalent ) 251 maintenance of garden for a period of six months including all required materials and man power etc., all inclusive....

Department Of Heavy Industry - Tamil Nadu

39999229 bids are invited for supply of cladding sheet for 2 x 660 mw ennore sez tpp mssheets of 0 6mm bare metal thickness having minimum yield strength 250 mpa and zinc aluminium alloy coating not less than 150 gm per sqm , ms sheets of 0 6mm bare metal thickness having minimum yield strength 250 mpa and galvanisation not less than 180 gm per sqm , z spacers made of at least 2 mm thick galvanized sheet of grade 375 , permanent colour coated metal cladding with troughed ms sheets of 0 6mm bare metal thickness having minimum yield strength 250 mpa and zinc aluminium alloy coating not less than 150 gm per sqm , 0 total quantity : 29890...

Southern Railway - Tamil Nadu

39996241 supply of light weight torque multiplierlight weight torque multiplier,light weight torque multiplier along with specialized reaction arm for torque enhancer as per the following specification. gear ratio 1:16. torque capacity 500 nm 4000 nm. accuracy: +/ 3 %. output square drive 1 inch. material aluminium alloy housing. weight not more than 5.4 kgs. non destructive over load protection for gear box. make/model no: ht92 95 awur of m/s norbar or dvv 40z of gedore or equivalent in griphold/ tekniplus/sweeney. [ warranty period: 30 months after the date of delivery ]...

Private Company - Tamil Nadu

39951468 auction sale of following items 1 miscelleneous aluminium items mt 15 multiple lots 2 aluminium alloy clamp (holders) mt 12 3 residual aluminium big size mt 300 4 residual aluminium small size mt 200 5 high chrome valves and current measurement instruments ( alloy) mt 3 6 rectifier, coolers, ac cooler and radiators cu radiators mt 4 7 rectifier, coolers, ac cooler and radiators al radiators mt 6 8 porcelain mt 100 9 wood mt 10 10 residual mixture mt 1000 11 hydrate mt 200 12 alumina powder mt 84 13 calcined alumina mt 16 14 decomposer scale mt 700 15 semi processed material mt 8000 16 rubber and polymer ( frp+hdpe+pvc +poly urethane + other related) mt 3 17 furniture material mt 0.5 18 xrd and related components ( spectrum) mt 3 19 ms material ( pipe and tank) & gi sheet dorr mt 1200 single lot / single bidder system 20 gearbox mt 12 21 pumps and valves mt 20 22 motors mt 10 23 cera wool ( dorr + stores) mt 20 24 foundry roof mt 200 25 electrical ( dorr and foundry ) & instrument material mt 5 26 aluminium cable mt 2 27 copper cable mt 2 28 cladding sheet al mt 0.1...

Nuclear Power Corporation Of India Limited - Tamil Nadu

39878283 preparation of drawings, supply of cs structural materials, zinc aluminium alloy coated profile sheet, fabrication, painting, construction of semi covered protective sheds and miscellaneous safety and security related structure, dismantling, modification and erection of shed with dismantled material, excavation of earth, supply and fixing of hilti anchor fastener...

Southern Railway - Tamil Nadu

39622565 supply of cordless impact wrench with complete set mode: single mode drive: 1 / 2 inch torque output: 1000 ft lb or more free speed: 1900 rpm or more battery voltage: 18 v warranty: one year it should able to rotate in both clock wise and anti clockwise, it should have voltage protection, dual bay battery charger, led light to illuminate work area. make: makita / bosch / stanley / ingersoll rand / fein [ warranty period: 12 months after the date of delivery ] , pneumatic impact wrench housing material: aluminium alloy size: 1 / 2 inch torque: 1085 nm operating pressure: 6.2 bar or less feature: handle exhaust warranty: one year weight: 2.5 kg or less make: chicago pneumatic / bosch / ingersoll rand / metabo / hazet [ warranty period: 12 months after the date of delivery ] , digital outside micrometer measurement range: 125 150 mm. leastcount: 0.001 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide display type: lcd material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency. make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , digital outside micrometer measurement range: 150 175 mm. leastcount: 0.001 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide display type: lcd material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency. make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , digital outside micrometer measurement range: 200 225 mm. leastcount: 0.001 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide display type: lcd material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , cordless small angle grinder. tool type: cordless disc diameter: 125 mm. grinding spindle thread: m14 no load speed: 10000 rpm battery voltage: 18 v battery included: yes warranty: one year make: bosch / makita / dewalt / stanley [ warranty period: 12 months after the date of delivery ] , analog outside micrometer measurement range: 175 200 mm. leastcount: 0.01 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , digital outside micrometer measurement range: 175 200 mm. leastcount: 0.001 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide display type: lcd material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , analog outside micrometer measurement range: 200 225 mm. leastcount: 0.01 mm. anvil: non removable with flat measuring face spindle end tipped with tungsten carbide material of the frame: stainless steel material of the spindle: hardned stainless steel. warranty: one year condition: 1. shape of frame of micrometer must be in semi circle ( c type ) 2. tenderer must attach photocopy of micrometer in bidding calibration certificate is required from nabl / ilac accredited agency make: insize / mitutoyo / baker / tesa / microgerman / brown and sharpe [ warranty period: 12 months after the date of delivery ] , ratchet type torque wrench square drive size: 1 / 2 inch torque range: 70 340 nm swing arc: 10 degree over all length: 780mm torque limiting direction: clock wise materail: steel; finish: chrome plated make:stanley bri tool or taparia or gedore or snap on or tristar [ warranty period: 12 months after the date of delivery ] , ratchet type torque wrench square drive size: 1 / 2 inch torque range: 10 70 nm swing arc: 10 degree over all length: 780mm torque limiting direction: clock wise materail: steel; finish: chrome plated make: stanley bri tool / taparia / snap on / tristar / gedore [ warranty period: 12 months after the date of delivery ] => limited...

Department of Defence Production - Tamil Nadu

39596421 bids are invited for 5 types of round steel round gr 20x2h4a 40mm dia steel , round gr st 20 12mm dia steel , round gr 30xgca steel 110 mm dia , round alluminium alloy 48mm dia , round hot rolled and annealed condition dia 32 total quantity : 10026...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

39583520 disposal of scrap available at central stores / sub stores , lot 1 material available at central stores / gcc / trichy 1 empty cylinder for gas of sizes 9 nos., 2 empty cylinder for gas of sizes 2nos., 3 scrap miscellaneous iron 8887 kgs., 4 scrap meters / meter parts 212 kgs., 5 scrap g.i. 2344 kgs., 6 scrap t & p 1607 kgs., 7 scrap teakwood 39 kgs., 8 scrap tube light fittings49 kgs., 9 condd. type writer 1 no., 10 condd. fan w / o regulator 4 nos., 11 condd. table fan 1 no., 12 condd. fire extinguisher 30 nos., 13 scrap alu. incl. aac cut bits3219 kgs., 14 scrap acsr1829 kgs., 15 condd. chain pulley block of sizes2 nos., 16 condd. chair 1 no., 17 scrap machinary part 538 kgs., 18 scrap copper cable2740 kgs., 19 scrap all alluminium alloy 150kgs., 20 condd. pt 11 kv w / o oil 2 nos. 21 condd.22 kv pts w / o oil 7 nos., 22 condd. cooling fan for auto transformer2 nos., 23 condd.computer monitor with cpu 1no., 24 condd. mv / sv / lamp 33nos., 25 condd. portable oil testing kit 2 nos., 26 scrap gi with porcelin 293 kgs., 27 scrap gi / ms tower angel 72 kgs., 28 scrap radiator 9 nos., 29 scrap alluminium with insulation190 kgs., 30 condd. window type a / c 1.5 tone7 nos., 31 scrap auto parts 28 kgs., 32 condd hydralic jack 50 ton 5 nos., 33 empty steel drum above 6 dia1no., 34 empty steel drum 3 to 6 dia1 no. , lot 21empty oil barrel 40 / 45gl.cap ( sh ) 228 nos. 2 empty oil barrel 40 / 45gl.cap ( leaky ) 480nos. , lot 3. 1 scrap gi wire42592 kgs. , lot 4. 1 scrap gi wire 42592 kgs. , lot 5. 1 empty steel drum 3 to 6 dia 38nos., 2 scrap miscellaneous iron 15121 kgs., 3 scrap g.i. 3611 kgs., 4 scrap gi pipe & fitting 360 kgs., 5 connd. gas cylinder 6 nos., 6 condd. dc panel 5 nos., 7 condd. transformer oil filter machine ( with out oil ) 1 no., 8 scrap reel wood 2410 kgs., 9 steel structure for 110 kv coupling cap.9nos., 10 mounting & elevating structure for 110 kv capacitor bank 1 nos., 11 clamp free end for 3 bus. 100 nos., 12 clamp alu. l clamp for panther 45 nos., 13 clamp t alu. for 75 mm bus to dbl zebra11 nos., 14 cable 4x25sqmm lt ug arm alu 64 m, 15 copper cable useful cut bits of various 97 m, 16 repair sleeves for panther conductors50 nos., 17 fitting ss for zebra with armar rod 22 nos., 18 repair sleeve for e / wire 7 / 9 20 nos., 19 clamp spacer for twin zebra 195 nos., 20 dt fittings for panther conductors 22 nos., 21 midspan compression joint ew 7 / 3.15mm 145 nos., 22 midspan compression joint ew 7 / 3.55mm 1355 nos., 23 midspan compression joint for zebra 50 nos., 24 pa rods for panther conductors 26 nos., 25. suspension fittings for ew 7 / 3.15mm 60 nos., 26 vibration damper with protectionrod 8 nos., 27 vibration dampers for zebra 50 nos., 28 washer spring gi18 mm 50kgs., 29 washer spring gi 20 mm640 kgs., 30 pb stub and cleats2set., 31 various template loose parts ( 14 items ) 1 set., 32 pc tower loose parts ( 4 items ) 1 set, 33 ls tower loose parts ( 23 items ) set 1, 34 ks tower loose parts ( 10 items ) 1 set, 35 g tower loose parts ( 3 items ) 1 set, 36 earth pipe gi 1 25mm32 nos. , lot 6. material available at sub stores / gcc / virudhachalam1 scrap miscellananeous iron78 kgs., 2 scrap acsr 812 kgs., 3 scrap gi wire 753 kgs., 4 scrap gi fitting 58 kgs., 5 scrap gi / ms tower angle 13922 kgs., 6 washer packing type gi 25mm 1955 kg., 7 gr tower template 5 set, 8 ksr tower template5 set, 9 lsr tower template 5 set, 10 pa template loose parts ( 10 items ) 1 set, 11 pc template loose parts ( 11 items ) 1 set, 12 gc template loose parts ( 7 items ) 1 set, 13 hc template loose parts ( 8 items ) 1 set. , lot 7.1. clamp dead end w / a type bolts 8 nos, 2. vibration damper for opgw 110 nos, 3. suspension assembly for opgw 1set, 4. bolt & nut gi 16x70 662 kgs, 5. levelling instrument with stand 3 nos, 6. bolt & nut gi 45x25mm 879 kgs, 7. bolt & nut gi 40x18mm 1000 kgs, 8. washer flat gi 20mm 854 kgs, 9. washer flat gi 18mm 1050 kgs, 10. bolt & nut gi 40x20mm 550 kgs, 11. bolt & nut gi 20x70mm 100 kgs, 12. kc template loose parts ( 4 items ) 1 set, 13. a template loose parts ( 10 items ) 1 set, 14. g template loose parts ( 18 items ) 1 set, 15. gcr, hcr, kcr template loose parts ( 16 items ) 1 set, 16. lsr black tower +6 mtr. exten. loose ( 58 items ) 1 set, 17. clamp dead end for kundha tensionfitting 3 nos, 18. gi spring washer 25mm 1205 kgs, 19. double tension without pass through jb 3 set, 20. plate washer 16x3 mm 315 kgs, 21.bolt & nut gi 24x70 582 kgs, 22. hand winch 1 no, 23. pa rod for leopard 10 set, 24. pa rod for zebra 123 nos, 25. pa rods for kundah conductors 34 nos, 26. vibration damper for kundah 26 nos, 27. fan pedestal 16 1 no, 28. chair twmp 3no, 29. table jc 42x24x30 3 nos, 30. drum stand ordinary 2 nos, 31. chest of drawer ( tw ) 1 no, 32. theodalite with stand 3 nos, 33. levelling staff 4 meters 1 no, 34. derrick ( tripoid ) 1 no, 35. four sleeve pulley 1 no and 36.triple sleeve pulley 1 no , lot 8.1 condemned power transformer 10 mva110 / 22 kvmaek:apex., sl.no: t 992 / 10.with out oil available at peraliss / perambalur edc 1 no. , lot 9. material available at sub stores / gcc / thanjavur1 scrap miscellanious iron 131 kgs ., 2 scrap gi42 kgs., 3 scrap teakwood 6 kgs., 4 scrap alu. incl.aac cut bits 8kgs., 5 scrap acsr 3746 kgs., 6 cond. chair1 no., 7 scrap gi wire13949 kgs., 8 scrap gi with porcelin 25 kgs., 9 scrap gi / ms tower angle48kgs., 10 cond. postal weighing balance1 set, 11 empty steel drum 3 to 6 dianos 63 , lot 10. 1 clamp bm switch end for panther acsr 12 nos., 2 steel structure for 110kv cc11 set, 3 230kv switch support str1 set, 4 washer flat gi 18mm 140 kgs., 5 washer packing type gi 25mm280 kgs., 6 bolt u type 16mm 1no., 7 various tower loose parts ( 16 items ) 1 set, 8 kcr 2 cleat 204 nos., 9 pa stub128 nos., 10 pa cleat56 nos., 11 pb 1 s stub 14 nos., 12 pb 2 s cleat 112nos., 13 hcr 2 cleat 61 nos., 14 ct marshalling box 1 no., 15 110kv ab switch support w / o 1 sw5l 7 set., 6 pa stub and cleat5 set, 17 gi spring washer 25mm 316 kgs., 18 p.a.+3 mtr extension 1 set, 19 tower parts for g 51 items 1set, 20 230kv bh fabrication structure 3 set, 21 230kv vc fabrication structure6 set, 22 aluminium earth bond with gi bolt & nut 100 nos., 23 bolt & nut gi 24x45mm1090 kgs., 24 bolt & nut gi 24x50mm 450 kgs., 25 bolt & nut gi 24x60mm 325 kgs., 26 bolt & nut gi 24x7065 kgs., 27 dt fittings for panther conductors 10nos., 28 fitting ss for zebra 26nos., 29 midspan compression joint ew 7 / 3.15mm 26nos., 30 midspan compression joint ew 7 / 3.55mm61 nos., 31 pa rod for leopard 26 nos., 32 pa rod for zebra200 nos., 33 pa rods for kundah conductors85 nos., 34 vibration dampers for zebra 5 nos., 35 washer packing gi 24mm40 kgs., 36 table teakwood sc 1 no. , lot 11. 1 various tower loose parts ( 28 items ) set 1 2 tower parts for g +6 extn. 25 items set 1...

Military Engineer Services - Tamil Nadu

39556098 tender for welcome maintenance and certain misc b / r repair worksto md offrs accn bldgs & periodical servicesto single officers accnatafac under age ( i ) ( af ) coimbatore. ; demolition of stone slabs and tiles of any description or thickness in floors, aprons, wall, etc, including cement mortar bedding ( but not backing ) and removing rubbish off the premises all as specified and as directed. 2 taking down shutters of any description n exc 1 sq.m each each andstacking for issuing under creditall as specified and as directed. 3 taking downshutters exc1 sq. m and n exc 2 sq. m eachandstacking for issuing under credit all as specified and as directed. 4 taking down shutters of any description exc 1.00 sqm and n exc 2 sqm each and stacking for issuing under credit all as specified and directed 5 taking up or down steel tubing of size 15mm dia including connections, valves, taps etcandstacking for issuing under credit., all as specified and as directed. 6 supply and fixsolid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with 19mm x 19mm ms square tube epdm rubber gasket weather seal to be provided throught the frame. the profile shall be mitre cut at two corners and jointed by inserting 02 nos of 150mm long bracket of 15mm x 15mm ms square tube inside the 19mm x 19mm ms square tube and suitable screwed the door frame shall be fixed to the wall using pvc fastners. a minimum of 6 nos screws to be provided for each frame all as specified and as directed.note: the quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces. 7 supply and fixing upvc window / ventlators25 mm thick factory made white colour partly glazed and partly stainless steelwiremesh window shutter consisting of frame made out of ms tube of19 gauge of size 15 mmx15 mm for style top &bottom rail .upvc channel of size 62 mmx25x50 mm forthe window shutter forming styles &rails glass panel and wire meshwill be externely in the clear space avilable between stiles and rails and fixedshutter upvc beading of size 12mmx8mm complete incluing solid upvc window frame of size 50mmx42 mm and 2 no alminum handle100 mm size, 2 no stainless steel hinges 75 mm size, 2 no alminum tower bolt 100 mm sizepowder coated ms sq bar 12 mm @100mm centre to centre should be fixed in upvc frame .sample as approved by age ( i ) / engr in charge . 8 s & f in repairs floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel fixed in floor with over all length of cover plate 140 mm fixed in repairs complete. 9 s & f in repiars 150mm ms ordinary helical springs ofordinary rat tail rod pattern springs including roller and roller plate complete in repairs. 10 supply and fix 35mm thick second class hard glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) for door all as specified and as directed. 11 supply and fix in repairsfactory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails. ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement all as specified and as directed. 12 m&l for 15mm thick screed bedin cement mortar 1:6 all as specified and as directed. 13 material and labour for non skid ceramic colouredtiles 7 to 8mm thick square / rectangular ) area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and all as specified. 14 material and labour for non skidcoloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed. 15 material and labour for non skidcoloured ceramic vitrified 8 to 10mm thick tiles ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchall as specified and as directed. 16 m&l for 10mm thick backing coat as in skirtingin cement mortar 1:6 all as specified and as directed 17 all as per item no. 13 above but as in skirting 18 all as per item no. 14 above but as in skirting 19 all as per item no. 15 above but as in skirting 20 material and labour for 300mm x 200mm x 7mm thick coloured glazed ceramic tiles onvertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchwith tile including 10mm thick backing coat in cement mortar 1:6 all as specified and as directed. 21 supply and fix grating doom 125mm dia with waste hole of ptmt ( minimum weight 40 gms ) all as specified and as directed. 22 s&f20 mm dia 3 layer pp r polyproperlene random copolymer ) concealed pipes sdr 7.4 ( pn 16 ) uv stablized andantimicobial fusion welded having thermal stability for hot & cold water supply including all pp r plain & brass threaded polyproplene random fittings fixed to walls, ceiling or in floors etccomplete all as specified and directed. 23 supply and fix in repairs 15mm dia bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and as directed.make: soma / leader / zolotto / sieko 24 supply and fix in repairs15mm dia stop valves, cast copper alloy, fancy type chromium plated with long shank and cub ( concealed type ) high pressure with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and as directed.make: soma / leader / zolotto / sieko 25 supply and fix in repairs brass chromium platedshower rose with or without swivel joints, 125mm size including fixing to 15mm dia steel pipe, all as specified and as directed.make: soma / leader / zolotto / sieko 26 supply and fix pvc cabinetof size 600 x 450mm with shelves and hinged cover all as specified and as directed.make : parryware / kohinoor / sintex 27 s&f of plastic water closet seat cover white , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinges device fixed in repairs 28 supply and fix 100mm size msbutt hinges medium weight all as specified and as directed. 29 supply and fix aluminium anodised barrel tower bolt of extruded section of size 150mm all as specified and as directed. 30 supply and fix extruded aluminium alloy handles, fabricated type, anodisedof size 125mm all as specified and as directed.make: classic / jyoti / shalimar / asoka 31 supply and fix 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and as directed. 32 material and labour for preparation of old decorated wall surfaces and applying one coat of oil bound distemper all as specified and as directed. 33 material and labour for preparation of old decorated ceiling surfaces and applying one coat of white wash all as specified and as directed. 34 m&l for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying onecoat of synthetic enamel paint all as specified and as directed. 35 all as per item no. 30but for old steel surfaces 36 m&l for preparation of old wall surfaces and applying one coat of white wash complete all as specified and directed. 37 material and labour for preparation of old decorated external wall surfaces and applying one coat of cement based paint all as specified and as directed. 38 supply and fixstainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed. 39 supply and fixstainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repairs all as specified and as directed. 40 supply and fix figured glass, pin head type, 4mm thick, and glazing with oil putty in squares not exceeding 0.50 sqm in each pane including hacking out old glass all as specified and as directed. 41 hacking out old broken glass from metal frame including punching or drilling out oldgalzing pins / spring clips and s / f sheet glass ordinary quality 3 mm thick, in squares n.exc. 0.50 sqm in each pane including. necessary new oil putty or with existing metal beadings complete. 42 supply and fix in repairs low level pvcflushing cistern white complete with syphonic action type 10 litre capacity including float valve handle, bracket, pvc flush down pipe 32mm dia as required with bend, etc complete all as specified and as directed. 43 s& f in repairs pvc waste pipe 32mm bore for , whb, and sink 44 supply and fix in repairsvitreous china wash down water closet pan ( pedestal pattern ) , white ( excluding flushing cistern and flush pipe ) , including fixing to existing 125 / 110mm size pvc ( swr ) p trap etc complete all as specified and as directed. 45 s& f in repairs viterous china wash hand basin white flat back size 450 x 300 mm excluding taps, chain and plug and porcelain stopper but including brackets, waste fittings of 32 mm waste pipeetc all as specified 46 supply and fix in repairs health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect as specified and as directed. 47 supply and fix in repairs brass chromium plated health faucet with hand held and spring operated control valve with pvc flexible pipe connection of suitable length as directed fixed to 15mm bore pipe all as specified and as directed. 48 material and labour for complete removal of existing treatementincluding washing, rubbing down and stopping of distempered and painted surfaces, applying 2 mm thick wall care puttyover a coat of chalk whitingprimer and applying two coats of acrylic emulsion distemper all as specified and directed. 49 m&l for chalk whitining on plastered wall surfaces preparatory to distemberingon wall wall surfaces in patches. 50 taking down cement plaster on brick or stone walls etc., including ceilingsincluding racking out joints, hacking for key, scrubbing down with wateretc., all as directed. 51 material and labour for rendering5mm thick in cement mortar1:3 on fair surfaces of brick work or concrete surfacesof ceiling in repair all as specified and directed 52 material and labour for preparation of theplastered surfaces of ceiling and applying three coats of white wash all as specified and directed. 53 material and labour for rendering 15mm thick in cement mortar1:6 on fair surfaces of brick work or concrete surfaces of wall , finishedeven and smooth without using extra cement all as specified and as directedwork in patches. 54 material and labour for preparation of newly plasteredwall surfaces, applying 3 mm thick wall care putty andapplyingtwo coats of acrylic emulsion distemper over acoat of chalk whiting primer completeall as specified and as directed. 55 material and labour for preparation of newly plasteredwall surfaces and applying two coats of white washcompleteall as specified and as directed. 56 material and labour for preparation of old treated surfaces of wall by cleaning with brush, filling the cracks / holes with approvedcrack filler and applying one coat of premium exterioracrylic emulsion paint ( matt ) completeall as specified and as directed....

Integral Coach Factory - Tamil Nadu

39399172 supply of led flame proof light fitting 20 w generally conforming to iec 60079 1:2007 and shall also meet the following technical requirements: 1.material : cast aluminium alloy lm6 2.flame proof:ex d zone 1 &2 , gas group iia & ii b as per is / iec 60079 1:2007 . 3.weather proof : ip / 65 as per is / iec 60529:2001. 4.operating voltage : 110 v dc 5.finish : light grey shade 631 / is 5 ( epoxy powder coated ) 6.mounting gasket : neoprene 7.earthing : 1 no. internal & 2 nos external with m6 tapped screws. 8.glass : heat resistant toughned type a flat glass. 9.the fitting shall be supplied along with suitable brass cable entry gland and dummy plug with strap suspension 10.the light fitting shall be supplied along with adaptor bracket ( mild steel powder coated matching to the light fitting finish ) suitable for wall mounting type. 11.the overall dimensions of the fitting ( including adaptor bracket ) shall not exceed 330 mm ( h ) x 205 mm ( d ) . note : 1. acceptable makes : m / s voltech manufacturing company ltd., m / s baliga lighting equipments ltd., & m / s scg exd tech pvt.ltd., 2. oems or their authourised dealers shall only be considered. 3. necessary test reports and test certificates from cmri shall be submitted for validation if required. 4. oga drawings with bom & technical details shall be got approved from icf before effecting bulk supply. [ warranty period: 30 months after the date of delivery ] => limited...

Southern Railway - Tamil Nadu

39322760 supply and installation of smart door lock for executive chamber having following specifications: 5 way unlocking using finger print, passcode, bluetooth mobile app, rfid access card and emergency key, upto 50 finger print, access sharing features two layer authentication, stainless steel ( 5 ) with wrong password alert. low battery alert via mobile app, material: aluminium, alloy steel, control method: voice, style: black; dimension: 34.l x 19. l x 12.2 cm approx. installation with standard accessories. make: schlage or qubo essential or wyze or kwikset or ultraloq. [ warranty period: 30 months after the date of delivery ] => limited...

Integral Coach Factory - Tamil Nadu

39244010 supply of unf alu alloy conduit size 25mm dia, aluminium alloy conduit ( 25mm dia, wall thickness 2.0mm ) of threadable quality to designation 63400 of table 1 and condition t6 ( new ) or wp ( ol d ) of table 2 of is:1285 ( latest ) suitable for electrical wiring, marking and dimensions shall confirm to clause 6 & 7 of is 9537 latest part ii . the supply of conduit shall be in standard length of 4 meters. note icf approved sources shall only be considered. [ warranty period: 30 months after the date of delivery ] furnishing depot / icf, chennai tamil nadu 15075.00 metre => limited...

Southern Railway - Tamil Nadu

39177645 supply of spare cast alluminium alloy aerofoil impeller duly balance suitable for mvsl blower to clw specification no. clw / es / b 14 alt. c [ warranty period: 30 months after the date of delivery ] => limited...

Municipal Adminitration And Water Supply Department - Tamil Nadu

39166405 tender for supply and errection of solar minimast led light ( 60w x 6nos ) in ward no.98 ; solar minimast led light ( 60w x 6nos ) supply, delivery and fixing of make : melon1. 60watts led fittings x 6nos2. aluminium alloy body3. triple water proof4. remote control operation5. ip 65 rating6. 10 meter height post with top circular ring7. with base plate, foundation bolt8. inclusive of installation ........ 1no costincluding gst 18% , installation and transportation...

Integral Coach Factory - Tamil Nadu

39141520 supply of unf conduit alu alloy 40mm dia to is, aluminium alloy conduit ( 40mm dia, wall thickness 2.0mm ) of threadable quality to designation 63400 of table 1 and condition t6 ( new ) or wp ( old ) of table 2 of is:1285 ( latest ) suitable for electrical wiring, marking and dimensions shall confirm to clause 6 & 7 of is 9537 latest part ii. the supply of conduit shall be in standard length of 4 meters. note as per dy.cmm / g letter no.04 / rb 120 / icf 206 / 707 dt.03.02.2023, eligibility criteria shall be : sl.no. c for items not listed in vendor directory of icf / rcf / mcf / rdso please find tender drawing key created for demand : 05231344 , this can be viewed in ireps vendor portal with key : 0523qakiv0r1344 [ warranty period: 30 months after the date of delivery ] furnishing tamil nadu 2209.00 metre => limited...

Southern Railway - Tamil Nadu

38865579 supply of mingle modular plt ( 41 seater ) work surface, mingle modular plt ( 41 seater ) work surface with mingle modular plt_2 str main st mingle modular plt_2 str, shared st 1350 x 600 x 740mingle modular plt 1800w st 1800 x 850 x 740, with accessories dsk 2 way name plate , dsk mod doc shelf, dsk hdmi wire man ( one packet contain 8 qty ) made of 25mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping.plastic abs access flap is provided for easy access to wires and cables. work top is available in various shapes as shown above. understructure it consist of 18mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. aluminium alloy 63400 wp profile is used for connecting panels together. the product has a knock down construction. modesty panel made of 18mm thick pre laminated twin board of e1 p2 grade and approved shade conforming to is 12823:1990, edge banded with matching 2 mm thick pvc lipping. powder coated accent metal strip provided below work surface to enhance aesthetics. it is made of 0.8mm crca as per is 513, epoxy polyester powder coated ( dft 40 60 microns. wire management an array of panels made of 0.8mm crca ms is:513, epoxy polyester powder coated ( dft 40 60 microns ) is used for flow of wires and cables. provision to mount anchor roma 6 module plate is provided below worktop. cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio , video cables onto worktop and connect devices charger to power socket below worktop. [ warranty period: 12 months after the date of delivery ] => limited...

Tamil Nadu Generation And Distribution Corporation Limited - Tamil Nadu

38740836 sale of non moving and obsolete items ferrous and non ferrous scraps etc sale of non moving and obsolete items ferrous and non ferrous scraps etc in central store thanjavur , lot 1 condemned distribution transformars without oil ( aluminium ) = 28 nos. 1.63 kva / 11 kv 12 nos. 2.100 kva / 11kv 10 nos. , 3. 150 kva / 11 kv 5 nos.4.250 kva / 11 kv 1 no the details of sl.nos.are given of specifications. , lot 2condemned distribution transformars without oil ( aluminium ) = 31 nos. 1.63 kva / 11 kv 8 nos. 2.100 kva / 11 kv 21 nos.3.150 kva / 11 kv 1 no. 4. 250 kva / 11 kv 1 no. the details of sl.nos.are given of specifications. , lot 3. condemned distribution transformars without oil ( copper ) = 27 nos.1. 50 kva / 11 kv 3 nos., 2. 50 kva / 22kv 1 no 3. 63 kva / 22 kv 1 no. 4.100 kva / 11 kv 9 nos.5. 150 kva / 11 kv 2 nos. 6. 200 kva / 11 kv 2 nos. 7.250 kva / 11 kv 7 nos. 8.100 kva / 22 kv 1 no 9. 200 kva / 22 kv 1 no10.condemned 11 kv metering set without oil 2 nos.9.condemned 11 kv ct without oil 28 nos. 10.condemned 33 / 11 kv ct polycrate 3 nos. 11. condemned vacuum interrupter 42 nos. , 12. condemned 11 kv pt 4nos., 13. condemned 33 kv pt 1no .14. condemned oil temprature indicator 1 no.15.condemned 110 kv pt 1no.16. condemned battery charger 5 nos.17. condemned 11 kv vcb 8nos the details of sl.nos.are given of specifications. , lot 4condemned distribution transformars without oil ( aluminium ) = 25 nos. 1.63 kva / 11 kv 14 nos. 2.100 kva / 11 kv 11 nos. the details of sl.nos.are given of specifications. , lot 5condemned distribution transformars without oil ( aluminium ) = 24 nos. 1.100 kva / 11 kv 21 nos. 2.150 kva / 11 kv 1 no. 3. 250 kva / 11 kv 2 nos. the details of sl.nos.are given of specifications. , lot 6.1.aluminium scrap ( aac ) 815 kgs., 2.acsr scrap 30063 kgs., 3. aluminium pvc cable scrap 110 kgs., 4. aaac scrap 7830 kgs., 5.brass scrap misc 1633 kgs., 6.scrap copper cable 4066 kgs.7. scrap aluminium ingot 181 kgs., 8.scrap tube light fitting 92 kgs., 9.condemned window type a / c 1.5 ton 12 nos.., 10.copper brass mixed scrap 21 kgs., 11.all aluminium alloy scrap 224 kgs. , lot 7.1. scrap miscellaneous iron 62000 kgs.2. scrap m.s / r.t.s grill 24881 kgs. 3. scrap auto parts 105 kgs.4. scrap r.s.joists cut bits 14819 kgs.5. scrap g.i 1602 kgs.6.scraptransformer lamination sheet 3141 kgs., 7. scrap rail cut bits 4330 kgs, 8.empty barrel 40 / 45 gal.cap.leaky 110 nos. 9. empty wooden drum 258 nos.10. scrap gi / ms tower angle 4122 kgs. 11.breather scrap 131 kgs. 12. condemned steel drum 3 ft. upto 6 ft.dia 4nos , lot 8.1.transformers aluminium wingding wire scraps with oil paperinsulation 29541 kgs.2. condemned tong tester 2 nos., 3.condemned relay of sizes 19 nos.4. condemned megger of sizes 2 nos., 5. condemned printer 47 nos., 6.condemned motor 0.25 hp 1 no., 7.condemned type writer 2 nos., 8.scrap teak wood 86 kgs., 9.condemned chain pulley block sizes 1no., 10. condemned transformer oil filter machine 1 no., 11. scrap deal wood 68 kgs 12. condemned radiator 1 no. 13.waste paper scrap 8975 kgs., 14. condemned ltct coil 98 nos. , lot 9. 1. condemned energy meter scrap 7690 kgs. 2. condemned high quality meter scrap 7861 kgs. 3.condemned static meter scrap 8510 kgs. 4. condemned cpu 54 nos.5. condemned 2 kva ups 17 nos. 6. condemned monitor 32 nos. 7.condemned 136 dot matrix printer 6 nos , lot 10 scrap m.s. form boxavailable at psc yard ayyampettai 83502 kgs...

Integral Coach Factory - Tamil Nadu

38698422 supply of led flame proof light fitting 20 w generally conforming to iec 60079 1:2007 and shall also meet the following technical requirements: 1.material : cast aluminium alloy lm6 2.flame proof:ex d zone 1 &2 , gas group iia & ii b as per is / iec 60079 1:2007 . 3.weather proof : ip / 65 as per is / iec 60529:2001. 4.operating voltage : 110 v dc 5.finish : light grey shade 631 / is 5 ( epoxy powder coated ) 6.mounting gasket : neoprene 7.earthing : 1 no. internal & 2 nos external with m6 tapped screws. 8.glass : heat resistant toughned type a flat glass. 9.the fitting shall be supplied along with suitable brass cable entry gland and dummy plug with strap suspension 10.the light fitting shall be supplied along with adaptor bracket ( mild steel powder coated matching to the light fitting finish ) suitable for wall mounting type. 11.the overall dimensions of the fitting ( including adaptor bracket ) shall not exceed 330 mm ( h ) x 205 mm ( d ) . note : 1. acceptable makes : m / s voltech manufacturing company ltd., m / s baliga lighting equipments ltd., & m / s scg exd tech pvt.ltd., 2. oems or their authourised dealers shall only be considered. 3. necessary test reports and test certificates from cmri shall be submitted for validation if required. 4. oga drawings with bom & technical details shall be got approved from icf before effecting bulk supply. [ warranty period: 30 months after the date of delivery ] => limited...

Southern Railway - Tamil Nadu

38646837 supply of pneumatic impact wrench sq drive: 3 / 4 inch, torque : 2700 nm, operating pressure :6.2 bar, body: aluminium alloy, weight :not more than 3.5, warranty:1 year, model:2146q1max of ingersoll rand or equivalent in dewalt / makita / chicago pneumatic. [ warranty period: 12 months after the date of delivery ] ...

Department of Defence Production - Tamil Nadu

38511938 bids are invited for aluminium alloy 7075 t6510, single extruded bars dia 135.0mm according to astm b 221m as per happ sp ( q3 ) mse exemption for turnover yes startup total quantity : 248767...